Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “optical materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Point defect formation in optical materials expos ed to the space environment

Point defect formation associated with early stages of optical damage was observed unexpectedly in two, and possibly three, different optical materials subjected to short-duration space exposure. Three calcium fluoride, two lithium fluoride, and three magnesium fluoride samples were flown on Space Shuttle flight STS-46 as part of the Evaluation of Oxygen Interactions with Materials - Third Phase experiment. One each of the calcium and magnesium fluoride samples was held at a fixed temperature of 60 C during the space exposure, while the temperatures of the other samples were allowed to vary with the ambient temperature of the shuttle cargo bay. Pre-flight and post-flight optical absorption measurements were performed on all of the samples. With the possible exception of the magnesium fluoride samples, every sample clearly showed the formation of F-centers in that section of the sample that was exposed to the low earth orbit environment. Solar vacuum ultraviolet radiation is the most probable primary cause of the defect formation; however, the resulting surface metallization may be synergistically altered by the atomic oxygen environment.

Allen, J. L.↗
NASA NTRS1990

Diamondlike carbon as a moisture barrier and antireflecting coating on optical materials

Diamondlike carbon (DLC) is amorphous, hard, semitransparent, and is under consideration for use as a coating material for infrared optics. DLC is also designated as a-C:H to indicate its amorphous nature as well as to indicate the presence of large (20 to 55 percent) amounts of hydrogen in the film. Two important questions arise with respect to use of DLC in infrared optics. Will the lack of grain boundaries help to keep moisture from penetrating the film. Secondly, application as an antireflection coating places restrictions on the allowed values of the index of refraction of the film relative to the particular substrate material being used. Will DLC have the correct index range. These two questions are addressed in this paper.

Woollam, John A.↗
NASA NTRS1998

Solution Growth of a Novel Nonlinear Optical Material: L-Histidine Tetrafluoroborate

Single crystals of L-Histidine tetrafluoroborate (L-HFB), a semiorganic nonlinear optical (NLO) material have been successfully grown by the temperature lowering and evaporation methods in our laboratory. Solubility curves of L-HFB have been determined in different solvents, such as water, ethanol and acetone. The solubility of L-HFB is very low in acetone, and ethanol, therefore, it is not feasible to grow L-HFB single crystals using these solvents. Good quality single crystals of a novel nonlinear optical material L-HFB have been grown from aqueous solution. Effects of seed orientation on morphologies of L-HFB crystals were studied. The advantages and disadvantage of both the evaporation and the temperature lowering techniques are compared. The single crystals in size 20 x 20 x 10 cubic mm were grown with deionized water as solvent in two weeks with an approximate growth rate of 1.4mm/day. The transmission range for these crystals has been found to be from 250 nm to 1500 nm.

Aggarwal, M. D.↗
NASA NTRS1987

Infrared fiber optic materials

The development of IR fiber optics for use in astronomical and other space applications is summarized. Candidate materials were sought for use in the 1 to 200 micron and the 200 to 1000 micron wavelength range. Synthesis and optical characterization were carried out on several of these materials in bulk form. And the fabrication of a few materials in single crystal fiber optic form were studied.

Feigelson, Robert S.↗
NASA NTRS1987

Organic nonlinear optical materials

Recently, it became clear that organic compounds with delocalized pi electrons show a great nonlinear optical response. Especially, secondary nonlinear optical constants of more than 2 digits were often seen in the molecular level compared to the existing inorganic crystals such as LiNbO3. The crystallization was continuously tried. Organic nonlinear optical crystals have a new future as materials for use in the applied physics such as photomodulation, optical frequency transformation, opto-bistabilization, and phase conjugation optics. Organic nonlinear optical materials, e.g., urea, O2NC6H4NH2, I, II, are reviewed with 50 references.

Umegaki, S.↗
NASA NTRS2004

Thermally Stable Heterocyclic Imines as New Potential Nonlinear Optical Materials

In the course of a search for new thermostable acentric nonlinear optical crystalline materials, several heterocyclic imine derivatives were designed, with the general structure D-pi-A(D'). Introduction of a donor amino group (D') into the acceptor moiety was expected to bring H-bonds into their crystal structures, and so to elevate their melting points and assist in an acentric molecular packing. Six heterocycle-containing compounds of this type were prepared, single crystals were grown for five of them, and these crystals were characterized by X-ray analysis. A significant melting temperature elevation was found for all of the synthesized compounds. Three of the compounds were also found to crystallize in acentric space groups. One of the acentric compounds is built as a three-dimensional H-bonded molecular network. In the other two compounds, with very similar molecular structure, the molecules form one-dimensional H-bonded head-to-head associates (chains). These chains are parallel in two different crystallographic directions and form very unusual interpenetrating chain patterns in an acentric crystal. Two of the compounds crystallized with centrosymmetric molecular packing.

Nesterov, Volodymyr V.↗
NASA NTRS1998

Crystal Growth of Mixed Optical Materials With the Automatic Czochralski Puller

Most of optical and semiconductor single crystalline materials produced in the electronic industry is grown with the Czochralski technique. This is the only technique capable of producing large high quality single crystals in a reasonable amount of time. The technique originated, and took its name, from pioneering work by Polish engineer J. Czochralski in 1917, who pulled single crystal wires (fibers) of low melting point metals from the melt in order to determine the maximum speeds at which they could be crystallized. The technique has been modified and its application has been extended first to the growth of silicon and later to a very wide range of compound semiconductors, metals, oxides and halides. It is now the dominant technique for the wide range of materials in the electronic industries. Czochralski growth is initiated by dipping a seed crystal of a chosen crystallographic orientation onto the surface of a melt contained in the heated crucible. The seed is then slowly withdrawn, solidifying the adherent column of the melt in steady state at an average rate given by the sum of the pulling rate and the rate of lowering the solid-liquid interface due to the depletion of the melt in the crucible. The control of the desired crystal diameter is achieved by closely controlling the heat balance at the solid-liquid interface.

Loutts, George B.↗
NASA NTRS1985

Orbital atomic oxygen effects on thermal control and optical materials - STS-8 results

The effects of exposing 23 specimens of optical and thermal control materials to space at 120 km altitude for over 40 hrs during the STS-8 mission are discussed. Ten samples of paint targeted for the Space Telescope (ST) and the Tethered Satellite were exposed, and included polyurethane, oxide, silicone, and glossy black and white samples which were scanned for alterations in the optical properties after being retrieved. Nine mirror-type materials were also investigated, along with silver specimens typical of solar cell interconnects. The oxygen flow at the orbital altitude was 3.5 x 10 to the 20th atoms/cu cm. The exposures caused no degradation of the magnesium fluoride mirror coatings, while the Kapton coating for the ST solar cell panels showed evidence of losing thickness. The Ag solar cell contacts will require coatings to extend their lifetimes. Overcoatings were also proven necessary for inhibiting degradation of painted surfaces.

Whitaker, A. F.↗
NASA NTRS1991

Reflective and refractive optical materials for earth and space applications; Proceedings of the Meeting, Orlando, FL, Apr. 4, 5, 1991

The present conference discusses beryllium mirror design and fabrication, production of aspheric beryllium optical surfaces by HIP consolidation, the control of thermally induced porosity for the fabrication of beryllium optics, fine-grained beryllium optical coatings, light-absorbing beryllium baffle materials, and advanced broadband baffle materials. Also discussed are radiation-resistant optical glasses, a catalog of IR and cryooptical properties of selected materials, durable metal-dielectric mirror coatings, the optical stability of diffuse reflectance materials, and optical filters for space applications.

Riedl, Max J.↗
NASA NTRS1996

Unsymmetrical squaraines for nonlinear optical materials

Compositions for use in non-linear optical devices. The compositions have first molecular electronic hyperpolarizability (.beta.) either positive or negative in sign and therefore display second order non-linear optical properties when incorporated into non-linear optical devices.

Marder, Seth R.↗
NASA NTRS1996

Computational Modeling of Ultrafast Pulse Propagation in Nonlinear Optical Materials

There is an emerging technology of photonic (or optoelectronic) integrated circuits (PICs or OEICs). In PICs, optical and electronic components are grown together on the same chip. rib build such devices and subsystems, one needs to model the entire chip. Accurate computer modeling of electromagnetic wave propagation in semiconductors is necessary for the successful development of PICs. More specifically, these computer codes would enable the modeling of such devices, including their subsystems, such as semiconductor lasers and semiconductor amplifiers in which there is femtosecond pulse propagation. Here, the computer simulations are made by solving the full vector, nonlinear, Maxwell's equations, coupled with the semiconductor Bloch equations, without any approximations. The carrier is retained in the description of the optical pulse, (i.e. the envelope approximation is not made in the Maxwell's equations), and the rotating wave approximation is not made in the Bloch equations. These coupled equations are solved to simulate the propagation of femtosecond optical pulses in semiconductor materials. The simulations describe the dynamics of the optical pulses, as well as the interband and intraband.

Goorjian, Peter M.↗
NASA NTRS1972

Measurements of the UV and VUV transmission of optical materials during high energy electron irradiation

An experimental program was conducted in which the optical transmission of several transparent materials was measured during high energy electron irradiation. These experiments were conducted using the Dynamitron electron accelerator as a continuous source of 1.5 MeV electrons and the LINAC electron accelerator as a pulsed source of 5-7 MeV electrons. The experimental program consisted of three major portions. The first portion, the optical transmission of fused silica, BeO, MgF2, and LiF was measured at vacuum ultraviolet wavelengths in the range 1550-2000 A during ambient temperature, 1.5 MeV electron irradiation at ionizing dose rates to 0.5 Mrad/sec. In the second portion of the program, the optical transmission of fused silica and BeO was measured in the range 2000-3000 A during high dose rate, elevated temperature 1.5 MeV electron irradiation. In particular, accurate measurements of the optical transmission were made at ionizing dose rates as high as 10 Mrad/sec. In the final portion of the program, the optical transmission of fused silica and BeO was measured in the wavelength range 2000-3000 A during pulsed 5 and 7 MeV electron irradiation from the LINAC accelerator. The maximum time averaged ionizing dose rate was limited to 0.75 Mrad/sec due to accelerator limitations.

Palma, G. E.↗
NASA NTRS2012

Development of Field-Controlled Smart Optic Materials (ScN, AlN) with Rare Earth Dopants

The purpose of this investigation is to develop the fundamental materials and fabrication technology for field-controlled spectrally active optics that are essential for industry, NASA, and DOD applications such as: membrane optics, filters for LIDARs, windows for sensors, telescopes, spectroscopes, cameras, flat-panel displays, etc. ScN and AlN thin films were fabricated on c-axis Sapphire (0001) or quartz substrate with the RF and DC magnetron sputtering. The crystal structure of AlN in fcc (rocksalt) and hcp (wurtzite) were controlled. Advanced electrical characterizations were performed, including I-V and Hall Effect Measurement. ScN film has a free carrier density of 5.8 x 10(exp 20)/per cubic centimeter and a conductivity of 1.1 x 10(exp 3) per centimeter. The background ntype conductivity of as-grown ScN has enough free electrons that can readily interact with the photons. The high density of free electrons and relatively low mobility indicate that these films contain a high level of shallow donors as well as deep levels. Also, the UV-Vis spectrum of ScN and AlN thin films with rare earth elements (Er or Ho) were measured at room temperature. Their optical band gaps were estimated to be about 2.33eV and 2.24eV, respectively, which are obviously smaller than that of undoped thin film ScN (2.4eV). The red-shifted absorption onset gives direct evidence for the decrease of band gap (Eg) and the energy broadening of valence band states are attributable to the doping. As the doped elements enter the ScN crystal lattices, the localized band edge states form at the doped sites with a reduction of Eg. Using a variable angle spectroscopic ellipsometer, the decrease in refractive index with applied field is observed with a smaller shift in absorption coefficient.

Kim, Hyun-Jung↗