Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “octane sensitivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Octane Requirements of Lean Mixed-Mode Combustion in a Direct-Injection Spark-Ignition Engine

Here, this study investigates the octane requirements of a hybrid flame propagation and controlled autoignition mode referred to as mixed-mode combustion (MMC), which allows for strong control over combustion parameters via a spark-initiated deflagration phase. Due to the throughput limitations associated with both experiments and 3-D computational fluid dynamics calculations, a hybrid 0-D and 1-D modeling methodology was developed, supported by experimental validation data. This modeling approach relied on 1-D, two-zone engine simulations to predict bulk in-cylinder thermodynamic conditions over a range of engine speeds, compression ratios, intake pressures, trapped residual levels, fueling rates, and spark timings. Those predictions were then transferred to a 0-D chemical kinetic model, which was used to evaluate the autoignition behavior of fuels when subjected to temperature–pressure trajectories of interest. Finally, the predicted autoignition phasings were screened relative to the progress of the modeled deflagration-based combustion in order to determine if an operating condition was feasible or infeasible due to knock or stability limits. The combined modeling and experimental results reveal that MMC has an octane requirement similar to modern stoichiometric spark-ignition engines in that fuels with high research octane number (RON) and high octane sensitivity (S) enable higher loads. Experimental trends with varying RON and S were well predicted by the model for 1000 and 1400 rpm, confirming its utility in identifying the compatibility of a fuel’s autoignition behavior with an engine configuration and operating strategy. However, the model was not effective in predicting (nor designed to predict) operability limits due to cycle-to-cycle variations, which experimentally inhibited operation of some fuels at 2000 rpm. Putting the operable limits and efficiency from MMC in the context of a state-of-the-art engine, the MMC showed superior efficiencies over the range investigated, demonstrating the potential to further improve fuel economy.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Influence of gasoline fuel formulation on lean autoignition in a mixed-mode-combustion (deflagration/autoignition) engine

We report stoichiometric spark-ignition engines suffer efficiency penalties due to throttling losses at low loads, a low specific-heat ratio of the stoichiometric working fluid, and limits on compression ratio due to end-gas autoignition leading to undesirable knocking. Mixed-Mode Combustion (MMC) mitigates these shortcomings by using a lean working fluid where a spark-initiated pilot-stabilized deflagrative flame front is followed by controlled end-gas autoignition. This MMC study investigates the effects of initial conditions (intake air temperature, intake pressure, equivalence ratio, and intake oxygen fraction) on autoignition tendency of four gasoline-range fuels with varying properties and composition. The use of fuels with varying octane sensitivity (S) allowed exploring the importance of low-temperature heat release in triggering autoignition. Fuels with high S were less reactive for conditions that promote low-temperature chemistry (operation at high intake air pressure or without N2 dilution). Conversely, an Alkylate fuel with low S showed a greater autoignition resistance at operating conditions that were unfavorable for low-temperature chemistry. Next, the effect of residual gas composition on autoignition tendency of fuels was examined with a chemical-kinetics model. Among the various molecules in the residual gas, nitric oxide (NO) enhanced the low-temperature chemistry and increased the autoignition tendency most significantly. The fuels’ autoignition response to increasing NO amount corroborates the experimental observations. Next, the sequential autoignition of the end-gas was assessed to be less impacted by thermal stratification because of lean mixtures showing relatively less low-temperature chemistry, when compared to stoichiometric mixtures. Next, the effect of changing equivalence ratio on the autoignition was found to be similar for all fuels, regardless of their S. With changing intake air temperature, the response of fuels’ autoignition tendency depended on the dilution level used. At high dilution (i.e. low intake [O2]), fuels’ reactivity increased with increasing intake air temperature. In contrast, for operation without dilution, the autoignition tendency of the low-S Alkylate fuel decreased with increasing intake air temperature, while that of high-S High Cycloalkane fuel still increased with increasing intake air temperature. In conclusion, conventional octane metrics (RON and MON) have utility in assessing the autoignition tendency under lean MMC operation. Moreover, the fuel requirements for MMC align with that of stoichiometric operation: i.e., high RON and high S fuels are desirable for stable non-knocking operation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Piston geometry and stroke optimization for high efficiency propane spark ignition engines

Propane has unique properties and offers interesting characteristics for high-efficiency spark ignition engines. Its high volatility reduces or completely eliminates fuel-wall wetting and facilitates fuel air mixing. Furthermore, propane has a research octane number of 112 and a high octane sensitivity of 15. Finally, its laminar flame speed is on the same order as that of conventional gasoline, and it exhibits high dilution tolerance. Modern spark ignition internal combustion engines rely on fast combustion rates and high dilution to achieve high brake thermal efficiencies. To accomplish this, high stroke-to-bore ratios and high geometric compression ratios have been used in new engine designs. Therefore, propane’s relatively high laminar flame speeds, high knock resistance, and dilution tolerance make it an excellent candidate fuel for modern spark ignition engines. The objective of this work is to co-optimize the piston geometry and the engine stroke to maximize the efficiency of a spark-ignition engine fueled with propane. 3D computational fluid dynamics (CFD) simulations employing the extended coherent flamelet model were used to study the parametric effects of piston shape and stroke length. A piston geometry based on high performing pistons was parameterized using four controlling parameters. The piston geometry and engine stroke design space was explored using deterministic and quasi-random sampling techniques. In conclusion, a Gaussian process regression model was built using the simulation data to explain the results observed.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

A wide range experimental and kinetic modeling study of the oxidation of 2,3-dimethyl-2-butene: Part 1

2,3-Dimethyl-2-butene (TME) is a potential fuel additive with high research octane number (RON) and octane sensitivity (S), which can improve internal combustion engine performance and efficiency. However, the combustion characteristics of TME have not been comprehensively investigated. Thus, it is essential to study the combustion characteristics of TME and construct a detailed chemical kinetic model to describe its combustion. In this paper, two high-pressure shock tubes and a constant-volume reactor are used to measure ignition delay times and laminar flame speeds of TME oxidation. Further, the ignition delay times were measured at equivalence ratios of 0.5, 1.0, and 2.0 in “air”, at pressures of 5 and 10 bar, in the temperature range of 950 – 1500 K. Flame speeds of the TME/ “air” mixtures were measured at atmospheric pressure, at a temperature of 325 K, for equivalence ratios ranging from 0.78 to 1.31. Two detailed kinetic mechanisms were constructed independently using different methodologies; the KAUST TME mechanism was constructed based on NUIGMech1.1, and the MIT TME mechanism was built using the Reaction Mechanism Generator (RMG). Both mechanisms were used to simulate the experimental results using Chemkin Pro. In the present work, reaction flux and sensitivity analyses were performed using the KAUST mechanism to determine the critical reactions controlling TME oxidation at the conditions studied.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Numerical analysis of soot emissions from gasoline-ethanol and gasoline-butanol blends under gasoline compression ignition conditions

In the present work, computational fluid dynamics (CFD) simulations of a single-cylinder gasoline compression ignition (GCI) engine were performed to investigate the impact of blending two biofuels, ethanol and n-butanol, with gasoline on the trade-off between combustion phasing and soot emissions under low load conditions. Here, in order to represent market gasoline (RD5-87), a four-component toluene primary reference fuel (TPRF) + ethanol (ETPRF) surrogate (with 20% ethanol by mole; E20) was formulated using a neural network based octane predictor such that the surrogate had the same ethanol content, Research Octane Number (RON) and Octane Sensitivity (S). In addition, a novel skeletal kinetic mechanism for ETPRF and TPRF + n-butanol (BTPRF) blends, incorporating polycyclic aromatic hydrocarbon (PAH) chemistry, was developed. A three-dimensional (3D) engine CFD formulation employing the skeletal mechanism, adaptive mesh refinement (AMR), finite-rate chemistry approach, and hybrid method of moments (HMOM) was adopted to capture the in-cylinder combustion phenomena and soot emissions. The engine CFD model was validated against RD5-87 experimental data for a broad range of start-of-injection (SOI) timings (-21/-27/-36/-45 crank angle degrees (CAD) after top-dead center (aTDC)), with respect to in-cylinder pressure, heat release rate, combustion phasing, and soot emissions. The closed-cycle simulation results were analyzed to elucidate the non-monotonic trend of soot emissions versus SOI timing: SOI-36 > SOI-45 > SOI-21 > SOI-27. Thereafter, the validated CFD model was employed to simulate the combustion of a gasoline-ethanol blend with 45% (by mole) ethanol (E45) and a gasoline-butanol blend with 45% (by mole) n-butanol (B45) under the same operating conditions to study the effects of fuel composition and SOI timing on combustion phasing and soot emissions. The sooting propensity followed the trend: B45 > E20 > E45 at all SOI timings. Overall, it was observed that the autoignition propensity was primarily related to fuel chemistry. On the other hand, sooting propensity showed strong coupling with both fuel chemistry and physical properties, with greater impact of fuel physical properties at advanced SOI timings.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Fuel property impacts on gaseous and PM emissions from a multi-mode single-cylinder engine

The U.S. Department of Energy’s Co-Optima initiative has focused on improving fuel economy and vehicle performance while reducing emissions through the simultaneous development of emerging sustainable fuels with beneficial properties and advanced combustion strategies. A major thrust has been the development of advanced compression ignition (ACI) combustion strategies of gasoline range fuels in combination with spark-ignited (SI) combustion in a single engine capable of multi-mode operation to achieve high power density with enhanced part load efficiency. The aim of this study was to further the understanding of how emissions from both ACI and SI strategies operating on the same fuels in the same engine are impacted by different fuel properties. This investigation focused on particulate matter (PM) and gaseous hydrocarbon emissions from 6 different fuels across 3 different combustion modes on the same single-cylinder engine designed for multi-mode operation: SI combustion, partial fuel stratification (PFS), and spark-assisted compression ignition (SACI). In each of these modes, 3 different CA50 phasings were studied such that all 6 fuels could be studied at the same phasings. Three of the six different fuels used were specially formulated in a previous investigation to study the impact of fuel distillation and aromatic content while maintaining the research octane number (RON) and octane sensitivity. Additionally, neat isooctane and two ethanol containing fuels (RD5-87 and Co-Optima E30) were studied. Different fuel and phasing impacts on emissions were observed across the three combustion modes. Fuel properties were found to impact soot PM and particle number more than the CA50 phasing, while the phasing had more impact on NOx emissions. The NOx emissions were reduced in the PFS mode for all fuels compared to SI combustion, but the SACI combustion mode did not reduce NOx emissions. Although PFS produced low soot PM emissions like SI, total PM mass emissions were significantly higher due to large organic carbon (OC) PM mass contribution. Both PFS and SACI had greater particle number emission than SI operation with small nuclei mode particles dominating in PFS compared to large agglomeration particles in SACI.

42 ENGINEERING↗
DOE OSTI2022

An experimental and modeling study on autoignition of 2-phenylethanol and its blends with n-heptane

2-Phenylethanol (2-PE) is an aromatic alcohol with high research octane number, high octane sensitivity, and a potential to be produced using biomass. Considering that 2-PE can be used as a fuel additive for boosting the anti-knocking quality of gasoline in spark-ignition engines and as the low reactivity fuel or fuel component in dual-fuel reactivity controlled compression ignition (RCCI) engines, it is of fundamental and practical interest to understand the autoignition chemistry of 2-PE, especially at low-to-intermediate temperatures (<1000 K). Based upon the experimental ignition delay time (IDT) results of neat 2-PE obtained from our previous rapid compression machine (RCM) investigation and the literature shock tube study, a detailed chemical kinetic model of 2-PE is developed herein, covering low-to-high temperature regimes. Besides, RCM experiments using binary fuel blends of 2-PE and n-heptane (nC7) are conducted in this work to investigate the nC7/2-PE blending effects, as they represent a dual-fuel system for RCCI operations. Furthermore, the newly developed 2-PE model is merged with a well-validated nC7 kinetic model to generate the current nC7/2-PE binary blend model. Overall, the consolidated model reasonably predicts the experimental IDT data of neat 2-PE and nC7/2-PE blends, as well as captures the experimental effects of pressure, equivalence ratio, and blending ratio on autoignition. Finally, model-based chemical kinetic analyses are carried out to understand and identify the controlling chemistry accounting for the observed blending effects in RCM experiments. In conclusion, the analyses reveal that nC7 enhances 2-PE autoignition via providing extra $\dot{O}$H radicals to the shared radical pool, while the diminished nC7 promoting effect on 2-PE autoignition with increasing temperature is due to the negative temperature coefficient characteristics of nC7.

2-phenlyethanol↗
DOE OSTI2022

A 100+ RON Gasoline Blendstock for High Efficiency, Low Emission Vehicles Engines - CRADA 493 (Final Report)

This study aimed at demonstrating production of a 100+RON gasoline fraction from a linear olefins feedstock to help improve further the viability and flexibility of the Pacific Northwest National Laboratory/ LanzaTech alcohol-to-jet (ATJ) patented process that converts ethanol from LanzaTech’s syngas fermentation process to low aromatic jet-range iso-paraffins. To achieve a high RON gasoline and ultimately a 100+RON, the technical approach consisted of converting the linear olefins into an iso-olefins rich mixture and then oligomerizing the iso-olefins rich mixture into high RON compounds in a single bed loaded with an acid catalyst that allows conversion at low reaction temperature. Three families of acid catalysts labeled as type A, B and C were investigated for the single-bed conversion of linear olefins into high RON gasoline range compounds. The effects of the nature of the catalyst, acid sites concentration and operating conditions were investigated. Fuel properties measurements and engine testing were conducted for the most promising catalyst. For type A catalysts, we demonstrated that the conversion increases with the increase of the Brönsted acid site concentration and that lower reaction temperature favors the formation of desired highly branched compounds. The highest dRON obtained with type A catalyst was equal to 94 (from NMR and IQT). Type B catalysts appear very effective for producing dimethyl-olefins compounds when operating at low reaction temperature (i.e., < 100°C). The highest dRON obtained with type B catalyst was equal to 92. The results suggest that type B catalysts are less favorable to internal conversion of linear olefins into iso-olefins compared to type A catalysts which leads to the formation of a gasoline blendstock with a lower dRON. A Type C catalyst that is less commonly used for production of gasoline range compounds from linear olefins was investigated due to its ability to favor conversion of linear olefins into iso-olefins. Compared to type A and type B catalyst, type C favors the formation of highly branched compounds (i.e., with 3+ methyl groups) in the gasoline range. Indeed, a gasoline blendstock containing about 33 wt.% of highly branched compounds was produced with type C catalyst while maintaining a high linear olefins conversion (i.e., 70%). A large quantity of this gasoline blendstock was produced and fuel properties measurements including engine testing for Research Octane Number (RON), Motor Octane Number (MON) and octane sensitivity (S) were conducted. A high RON = 97, MON = 82.7, S =14.3, AKI = 90 and HoV = 334.1kJ/kg were measured. While a RON of 100 was not achieved, the fuel properties of the gasoline blendstock are very acceptable as compared to current premium gasoline. Overall, these results highlight the potential for producing a high RON/ premium gasoline blendstock starting from a linear olefins feedstock.

02 PETROLEUM↗
DOE OSTI2021

A Rapid Compression Machine Study of 2-Phenylethanol Autoignition at Low-To-Intermediate Temperatures

To meet the increasing anti-knocking quality demand of boosted spark-ignition engines, fuel additives are considered an effective approach to tailor fuel properties for satisfying the performance requirements. Thus, screening/developing bio-derived fuel additives that are best-suited for advanced spark-ignition engines has become a significant task. 2-Phenylethanol (2-PE) is an attractive candidate that features high research octane number, high octane sensitivity, low vapor pressure, and high energy density. Recognizing that the low temperature autoignition chemistry of 2-PE is not well understood and the need for fundamental experimental data at engine-relevant conditions, rapid compression machine (RCM) experiments are therefore conducted herein to measure ignition delay times (IDTs) of 2-PE in air over a wide range of conditions to fill this fundamental void. These newly acquired IDT data at low-to-intermediated temperatures, equivalence ratios of 0.35–1.5, and compressed pressures of 10–40 bar are then used to validate the 2-PE model developed by Shankar et al. (2017). It is found that this literature model greatly overpredicts the current RCM data. The comparison of experimental and simulated results also provides insights into 2-PE autoignition behaviors at varying conditions. Further chemical kinetic analyses demonstrate that the absence of the O2-addition pathway of β-R. radical in the 2-PE model of Shankar et al. (2017) could account for the model discrepancies observed at low-to-intermediated temperatures.

Fang, Ruozhou (ORCID:0000000348315100)↗
DOE OSTI2020

Fuel Property-Informed Process Design for the Direct Catalytic Conversion of Cellulosics

The direct catalytic conversion of cellulosics (DC3) with supercritical methanol presents a promising pathway to completely solubilize woody biomass and produce >60% mass yield of C2-C6 oxygenates for light duty vehicle applications. Although the oxygenate composition can be tuned by modifying catalyst and process conditions, limited efforts to date have examined DC3 fuel properties for light duty fuel applications to iteratively inform conversion process design. In this work, we designed and evaluated multi-component surrogate bioblendstocks that represent major DC3 light oxygenates and refined catalyst formulations and distillation parameters to improve the resulting light duty fuel quality. Surrogate design for this novel fuel production pathway was based on a preliminary product slate that was systematically adjusted to determine impacts on fuel properties of interest including heating value, oxidative stability, and heat of vaporization, among others. The resulting predictions and measurements of these surrogates were then used to inform improvement of conversion process, and specifically, reformulation of the catalyst which resulted in production of a higher energy density fuel product primarily comprised of saturated alcohols. Fuel testing outcomes also informed downstream oxygenate separations requirements. This resulted in the production of a promising DC3 light-duty fuel blendstock with >15% greater energy density relative to ethanol, while maintaining high octane number and octane sensitivity.

BIOMASS FUELS↗
DOE OSTI2021

Octane Index Applicability over the Pressure-Temperature Domain

Modern boosted spark-ignition (SI) engines and emerging advanced compression ignition (ACI) engines operate under conditions that deviate substantially from the conditions of conventional autoignition metrics, namely the research and motor octane numbers (RON and MON). The octane index (OI) is an emerging autoignition metric based on RON and MON which was developed to better describe fuel knock resistance over a broader range of engine conditions. Prior research at Oak Ridge National Laboratory (ORNL) identified that OI performs reasonably well under stoichiometric boosted conditions, but inconsistencies exist in the ability of OI to predict autoignition behavior under ACI strategies. Instead, the autoignition behavior under ACI operation was found to correlate more closely to fuel composition, suggesting fuel chemistry differences that are insensitive to the conditions of the RON and MON tests may become the dominant factor under these high efficiency operating conditions. This investigation builds on earlier work to study autoignition behavior over six pressure-temperature (PT) trajectories that correspond to a wide range of operating conditions, including boosted SI operation, partial fuel stratification (PFS), and spark-assisted compression ignition (SACI). A total of 12 different fuels were investigated, including the Co-Optima core fuels and five fuels that represent refinery-relevant blending streams. It was found that, for the ACI operating modes investigated here, the low temperature reactions dominate reactivity, similar to boosted SI operating conditions because their PT trajectories lay close to the RON trajectory. Additionally, the OI metric was found to adequately predict autoignition resistance over the PT domain, for the ACI conditions investigated here, and for fuels from different chemical families. This finding is in contrast with the prior study using a different type of ACI operation with different thermodynamic conditions, specifically a significantly higher temperature at the start of compression, illustrating that fuel response depends highly on the ACI strategy being used.

02 PETROLEUM↗
DOE OSTI2020

From Atom to Engine: Understanding Fundamental Effects of Structure on Combustion Using Tandem Experiment and Computation

The ability to tie structural features to a fuel candidate’s ignition properties provides a path for rational design of advantaged fuels that facilitate higher-efficiency, lower-emitting combustion in engines. The time evolution of a fuel’s radical population directly correlates with global combustion parameters, and because the generated radicals depend on the initial structure and reaction pathways of the fuel molecule, it follows that the molecular structure of a fuel has a direct impact on this cascade, and therefore salient ignition-tied fuel properties. This work aims to understand the impact of structural features in the context of global combustion properties for direct application to emerging engine technologies. Specifically, we highlight the ability to identify potential fuel blendstocks for specific engine strategies by examining and elucidating the radical cascade tied to ignition. A representative subset of alcohols possessing a variety of structural features (e.g. branching, chain length) was selected for study using a robust combination of experimental and computational methods. The approach begins with identifying short-lived radicals and likely abstraction sites upon pyrolysis in a microreactor coupled with photoionization mass spectrometry for direct detection of product species. In tandem, electronic structure calculations were performed to calculate the relevant potential energy surfaces for fuel pyrolysis as well as the subsequent O2 addition-isomerization reactions, which govern ignition behavior. Furthermore, the theoretical energetic and ro-vibrational data are used to calculate rate constants for direct ignition modeling to explore how structural effects impact NTC behavior. The microreactor data combined with electronic structure theory calculations provide a well-informed picture of the reactions relevant to ignition for each fuel in this study, as well as the most likely radicals generated under engine conditions. This thorough fundamental picture of fuel decomposition and ignition chemistry is used to correlate the observed ignition behavior to molecular structural effects.

advanced biofuels↗
DOE OSTI2024

Potential Adoption and Benefits of Co-Optimized Multimode Engines and Fuels for U.S. Light-Duty Vehicles

Exploring a diverse portfolio of technologies for decarbonization is crucial to understanding the potential impacts of different technological solutions and their associated environmental implications. Using high-octane, high-sensitivity biofuel blends in co-optimized multimode engines can increase engine efficiency and reduce vehicle emissions. Here, the multimode engine research focuses on the benefits of light-duty vehicle engines, which can operate in multiple modes depending on the vehicle's load. Low-temperature combustion can improve efficiency and reduce emissions (such as those from oxides of nitrogen and particulate matter) during low-load operation, while spark ignition performance is maintained in high-load operation. These advanced engines can be optimized to run on blends of biobased fuels. This analysis models scenarios for potential market adoption of co-optimized multimode vehicles fueled by three different bioblendstocks: ethanol, isopropanol, and isobutanol. An integrated modeling approach is used to forecast the energy and environmental impacts of the deployment of co-optimized multimode vehicles and fuels in the light-duty sector over the 2020-to-2050 time horizon. The multidisciplinary approach combines vehicle sales modeling, system dynamics modeling of the biorefining industry, and life cycle assessment to estimate the emissions and energy benefits. The models consider market forces such as consumer preferences for vehicle attributes, biofuel supply and demand dynamics subject to biorefinery capacity build-out and bioresource constraints, and forecasted changes to the U.S. bulk energy system over time. Market adoption of co-optimized vehicles is evaluated across a wide parameter space for incremental vehicle cost and engine efficiency improvement. This analysis reveals that the deployment of co-optimized multimode fuels and vehicles results in up to a 5% reduction in annual sector-wide life cycle greenhouse gas (GHG) emissions by 2050, relative to a business-as-usual scenario, but is also indicates environmental trade-offs, such as higher life cycle water-use. Emission benefits could potentially increase beyond 2050, as the new technologies penetrate the market and gain a foothold. Results also show that, under certain circumstances, vehicles with engines co-optimized for use with high-octane, high-sensitivity biofuel blends can be cost-competitive with conventional gasoline, while reducing GHG emissions. Our modeling results indicate that co-optimized multimode fuels and engines can be strategically leveraged in tandem with electrification to decarbonize the light-duty sector. Co-optimized vehicles could play a role in the early years of the time horizon, while electric vehicles (EVs) could become more competitive in the later years, highlighting the complementary benefits of these technologies for GHG reductions.

Oke, Doris↗
DOE OSTI2022

Enhancing $\phi$-sensitivity of ignition delay times through dilution of fuel-air mixture

The high $\phi$-sensitivity (η) of ignition delay time (τ IDT ) is one of the desirable fuel properties for the high-load extension of advanced compression ignition engine. Recent studies revealed the effectiveness of a high dilution rate (x D ) for enhancing η at the engine-relevant conditions. This study aims to quantify the effect of dilution on the η of isooctane using a combined experiment-simulation approach. The ignition delay of the isooctane/air mixture was measured with an Advanced Fuel Ignition Delay Analyzer (AFIDA) over the temperature range of 623 - 923 K at 10 bar pressure with global $\phi$ = 0.3 - 0.6, with and without 28.6% of additional N 2 dilution. For precise evaluation of experimental η, the facility effect of the AFIDA experiment was characterized with three-dimensional computational fluid dynamics (3-D CFD) simulation. The temperature in the combustion chamber from 3-D CFD indicated a substantial temporal dependency, varying up to ~52 K by charge-cooling of fuel injection and heat transfer from the wall. We introduced the dimensionless number θ(t) for characterizing the temporal profile of chamber temperature. Consideration of the facility effect using θ(t) resulted in better agreement between the experimental ..eta.. and zero-dimensional (0-D) kinetics simulation. The refined η were then further utilized to quantify the effectiveness of dilution to η The extent of η enhancement with dilution strategy was maximized at the low-temperature chemistry regime, increasing η by 77% with a 28.6% dilution rate. Further analysis on the dilution effect was carried out using 0-D kinetics simulation, revealing the critical dimensionless numbers relevant to the effectiveness of dilution to η enhancement. Here, this study is the first experiment-simulation combined research to quantify the effect of dilution on η, facilitating the kinetics model refinement for better reproduction of $\phi$-sensitivity.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Economic analysis of the benefits to petroleum refiners for low carbon boosted spark ignition biofuels

A refinery modeling framework is developed to estimate the benefits of blending high-quality biofuels directly with refinery gasoline components for attaining a premium grade fuel (also termed as Co-Optima Boosted SI gasoline here). Our results change the paradigm of bio-blendstocks (BBs) being competitors to fossil components, by identifying opportunities for refineries to add value to their product slate, from some favorable BB properties. This potential value can be characterized by calculating the breakeven value (BEV), as defined down below. The proposed modeling framework incorporates extensive data from (1) projected product over the next few decades, (2) crude oil and refinery products pricing, and (3) fuel specifications. The complete refinery models serve as a basis for assessing the value of biofuels, assuming profitability remains the same for representative petroleum refinery configurations. Our assessment showed wide range of variation of biofuels BEV from $\$$20-$\$$120/bbl, within the considered blending level and crude prices. Further, the BEV was correlated with the fuel octane ratings such as octane numbers (research, RON and motor octane numbers, MON) and both antiknock index (AKI, average of RON and MON) and sensitivity (S, difference between RON and MON), with a slightly higher correlation with the sensitivity. However, the expected decrease in gasoline demand for the upcoming years could negatively impact biofuels demand and value, in a business-as-usual scenario. Our analysis also showed a more valuable bio-blendstocks incorporation in smaller refineries since they can enhance the capabilities for producing specialty, high-value fuels/products, and introduce high octane-barrels into otherwise constrained blending operations. Additional implications towards refiners include opportunities to rebalance operations, access to high-value fuel markets, and synchronization with broader transportation industry trends. Furthermore, results indicate the value of Co-Optima boosted spark ignition (BSI) efficiency gains can extend to refiners to incentivize decarbonization and diversified feedstock production.

09 BIOMASS FUELS↗
DOE OSTI2024

A chemical kinetic analysis of knock propensity of methanol-to-gasoline fuel

Production of low carbon gasoline-like fuels such as methanol-to-gasoline (MTG) is a promising approach to achieve rapid greenhouse gas emission reduction of the transportation sector. Despite the fact that gasoline that meets the ASTM D4814 standard for automotive spark-ignition engine fuel can be readily produced from these processes, it is unclear how the composition of MTG may affect engine performance and emissions. Here, in this paper, a surrogate for an MTG is used to numerically study the effects of gasoline composition on knock propensity and on the sensitivity of knock to thermal and fuel stratification, to oxygen dilution and to nitric oxide from exhaust gas recirculation of residual gases. Simulations were performed in ANSYS CHEMKIN-PRO using a comprehensive chemical kinetic mechanism for gasoline surrogates, and results of the MTG surrogate were compared against those of a petroleum-based regular E10 gasoline, termed PACE-20. A premium-grade MTG fuel was also formulated by adding ethanol to the MTG surrogate, and results were compared against those of four premium-grade, gasoline-like fuels representative of future alternative gasoline formulations. Surrogates and mechanism were evaluated by comparison against experimental engine data, and the model showed high accuracy at stoichiometric conditions (mean absolute error of ignition timing equal to 1.46 crank angle degrees) but larger deviations at lean conditions (mean absolute error of ignition timing equal to 5.52 crank angle degrees). Despite the fact that the MTG surrogate has a RON 1.1 units higher than that of PACE-20, it may show higher knock propensity at medium temperature conditions due to a less intense NTC behavior. MTG autoignition was more temperature- and equivalence ratio-sensitive than that of PACE20, suggesting that MTG can benefit more from naturally-occurring thermal stratification or from induced fuel stratification of the end gas to mitigate knock intensity. The sensitivity of autoignition reactivity to oxygen dilution and to NO concentration was higher for MTG than for regular gasoline at medium loads, but the opposite trend was observed at high loads due to the effect of pressure on the low-temperature chemistry of regular gasoline. Approximately 14 % vol ethanol content was required to upgrade the octane rating of MTG from regular grade to premium grade. Adding 13.6 % vol ethanol made the fuel autoignition less sensitive to both oxygen dilution and NO content (ignition time varies approx. 17 % and 50 % less with oxygen dilution and NO addition, respectively, when adding ethanol at high engine loads).

02 PETROLEUM↗