SEARCH · Engineering Papers

Results for “nanocomposite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS2004

Polymer/Silicate Nanocomposites Used to Manufacture Gas Storage Tanks With Reduced Permeability

Over the past decade, there has been considerable research in the area of polymer-layered silicate nanocomposites. This research has shown that the dispersion of small amounts of an organically modified layered silicate improves the polymer strength, modulus, thermal stability, and barrier properties. There have been several reports on the dispersion of layered silicates in an epoxy matrix. Potential enhancements to the barrier properties of epoxy/silicate nanocomposites make this material attractive for low permeability tankage. Polymer matrix composites (PMCs) have several advantages for cryogenic storage tanks. They are lightweight, strong, and stiff; therefore, a smaller fraction of a vehicle's potential payload capacity is used for propellant storage. Unfortunately, the resins typically used to make PMC tanks have higher gas permeability than metals. This can lead to hydrogen loss through the body of the tank instead of just at welds and fittings. One approach to eliminate this problem is to build composite tanks with thin metal liners. However, although these tanks provide good permeability performance, they suffer from a substantial mismatch in the coefficient of thermal expansion, which can lead to failure of the bond between the liner and the body of the tank. Both problems could be addressed with polymersilicate nanocomposites, which exhibit reduced hydrogen permeability, making them potential candidates for linerless PMC tanks. Through collaboration with Northrop Grumman and Michigan State University, nanocomposite test tanks were manufactured for the NASA Glenn Research Center, and the helium permeability was measured. An organically modified silicate was prepared at Michigan State University and dispersed in an epoxy matrix (EPON 826/JeffamineD230). The epoxy/silicate nanocomposites contained either 0 or 5 wt% of the organically modified silicate. The tanks were made by filament winding carbon fibers with the nanocomposite resin. Helium permeability was measured by Northrop Grumman, showing that the leak rate/day of the nanocomposite matrix tank was approximately 80-percent less than that of the neat epoxy matrix tank.

Campbell, Sandi G.↗

DOE OSTI2020

Polymer Chain Diffusion in All-Polymer Nanocomposites: Confinement vs Chain Acceleration

All-polymer nanocomposites, in which soft, polymer-based nanoparticles are dispersed in the polymer matrix, have received great interest lately due to their potential use in a range of applications, including drug delivery and self-healing materials. However, the impact of this new class of nanoparticles on the dynamics of a linear polymer matrix in an all-polymer nanocomposite is still largely unknown. In this work, we report that the addition of polystyrene soft nanoparticles accelerates the diffusion of high molecular weight linear PS chains over a range of nanoparticle loadings. Our results show that at nanoparticle loadings below 1%, the diffusion of the linear matrix increases, presumably via a constraint release mechanism. At loadings above 1%, the increase in diffusion is mitigated by confinement effects of the nanoparticles. Thus, the response of these all-polymer nanocomposites is dominated by the balance of entropic confinement of the chain, which slows diffusion and a constraint release mechanism that speeds up the diffusion. However, the diffusion of the linear chain in the all-polymer nanocomposite is faster than that of the same chain in the melt at all loadings, diverging from the behavior of most nanocomposites with hard, impenetrable nanoparticles. Thus, the mechanism that accelerates the chain diffusion dominates in these systems. This behavior is unusual and fundamentally different than what has been reported for nanocomposites with hard inorganic nanoparticles, indicating that new perspectives are needed for these materials where the control of loading can either accelerate or decelerate the dynamics of the matrix in a distinctive manner.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Exsolution Synthesis of Nanocomposite Perovskites with Tunable Electrical and Magnetic Properties

Nanostructured functional oxides play an important role in enabling clean energy technologies and novel memory and processor devices. Using thin-film La 0.6 Sr 0.4 FeO 3 (LSF) as a model system, the novel utility of exsolution in fabricating self-assembled metal oxide nanocomposites with tunable functionalities is shown. Exsolution triggers the formation of metallic iron (Fe 0 ) nanoparticles, Ruddlesden–Popper domains, and nm-scale percolated Fe-deficient channels in LSF. Combining multimodal characterization with numerical modeling, the chemical, magnetic, and electrical properties of the exsolution-synthesized nanocomposite at different stages of Fe 0 exsolution as well as during redox cycling are assessed. After exsolution, the electronic conductivity of the nanocomposite LSF increased by more than two orders of magnitude. Based on numerical analysis representing all the constituents, it is expected that this increase in conductivity originates mainly from the Fe-deficient percolating channels formed during exsolution. Moreover, the exsolved nanocomposite is redox-active even at moderate temperatures. Such redox capabilities can enable dynamic control of the nanocomposite functionality by tailoring the oxygen non-stoichiometry. This concept is demonstrated with a continuous modulation of magnetization between 0 and 110 emu cm -3 . These findings point out that exsolution may serve as a platform for scalable fabrication of complex metal oxide nanocomposites for electrochemical and electronic applications.

36 MATERIALS SCIENCE↗

NASA NTRS2002

Viscoelastic and Mechanical Properties of Thermoset PMR-type Polyimide-Clay Nanocomposites

High temperature thermoset polyimide-clay nanocomposites were prepared by blending 2.5 and 5 wt% of an unmodified Na(+-) montmorillonite (PGV) and two organically modified FGV (PGVCl0COOH, PGVC12) with a methanol solution of PMR-15 precursor. The methanol facilitated the dispersal of the unmodified clay. Dynamic mechanical analysis results showed a significant increase in the thermomechanical properties (E' and E") of 2.5 wt% clay loaded nanocomposites in comparison with the neat polyimide. Higher glass transition temperatures were observed for 2.5 wt% nanocomposites compared to the neat polyimide. Flexural properties measurements for the 2.5 wt% nanocomposites showed a significant improvement in the modulus and strength, with no loss in elongation. This trend was not observed for the 5 wt% nanocomposites. An improvement in the CTE was observed for the PGV/PMR-15 nanocomposites, while a decrease was observed for the organically modified samples. This was attributed to potential variations in the interface caused by modifier degradation.

Abdalla, Mohamed O.↗

NASA NTRS2007

Polymer-Layered Silicate Nanocomposites for Cryotank Applications

Previous composite cryotank designs have relied on the use of conventional composite materials to reduce microcracking and permeability. However, revolutionary advances in nanotechnology derived materials may enable the production of ultra-lightweight cryotanks with significantly enhanced durability and damage tolerance, as well as reduced propellant permeability. Layered silicate nanocomposites are especially attractive in cryogenic storage tanks based on results that have been reported for epoxy nanocomposite systems. These materials often exhibit an order of magnitude reduction in gas permeability when compared to the base resin. In addition, polymer-silicate nanocomposites have been shown to yield improved dimensional stability, strength, and toughness. The enhancement in material performance of these systems occurs without property trade-offs which are often observed in conventionally filled polymer composites. Research efforts at NASA Glenn Research Center have led to the development of epoxy-clay nanocomposites with 70% lower hydrogen permeability than the base epoxy resin. Filament wound carbon fiber reinforced tanks made with this nanocomposite had a five-fold lower helium leak rate than the corresponding tanks made without clay. The pronounced reduction observed with the tank may be due to flow induced alignment of the clay layers during processing. Additionally, the nanocomposites showed CTE reductions of up to 30%, as well as a 100% increase in toughness.

Miller, Sandi G.↗

DOE OSTI2020

Poly(9,9-dioctylfluorene-co-fluorenone-co-methylbenzoic ester), carbon nanotubes, and sulfur nanocomposite, electrode and lithium-fulfur battery including the same

The present invention provides for a composition of matter comprising: poly(9,9-dioctylfluorene-co-fluorenone-co-methylbenzoic ester)(PFM), carbon nanotubes (CNT), and sulfur particles nanocomposite, wherein the nanocomposite is porous. The present invention also provides for an electrode comprising: poly(9,9-dioctylfluorene-co-fluorenone-co-methylbenzoic ester)(PFM), carbon nanotubes (CNT), and sulfur particles nanocomposite, wherein the nanocomposite is porous. The present invention also provides for a lithium sulfur (Li—S) battery comprising: an electrode comprising poly(9,9-dioctylfluorene-co-fluorenone-co-methylbenzoic ester)(PFM), carbon nanotubes (CNT), and sulfur particles nanocomposite, wherein the nanocomposite is porous.

Liu, Gao↗

DOE OSTI2024

RF cured nanocomposite adhesives for multi-material joining applications

A method for fabricating, and curing, nanocomposite adhesives including introducing nanoheater elements into a heat-curing adhesive to fabricate a nanocomposite adhesive, and providing a radio-frequency (RF) electromagnetic wave to the nanocomposite adhesive to heat, and cure the nanocomposite adhesive. The nanocomposite adhesive is physically applied to first and second materials to bond the first and second materials upon curing of the nanocomposite adhesive, and the RF electromagnetic wave has a frequency in the radio-frequency range, having energy that is transferred to the nanoheater elements by electromagnetic wave interactions with permanent and induced dipoles, intrinsic photon-phonon interaction, or interactions with nanoheater defects and grain structures.

Zhang, Yuepeng↗

DOE OSTI2020

Review on the growth, properties and applications of self-assembled oxide–metal vertically aligned nanocomposite thin films—current and future perspectives

Self-assembled oxide–metal nanocomposite thin films have aroused great research interest owing to their wide range of functionalities, including metamaterials with plasmonic and hyperbolic optical properties, and ferromagnetic, ferroelectric and multiferroic behaviors. Oxide–metal nanocomposites typically self-assemble as metal particles in an oxide matrix or as a vertically aligned nanocomposite (VAN) with metal nanopillars embedded in an oxide matrix. Among them, the VAN architecture is particularly interesting due to the vertical strain control and highly anisotropic structure, enabling the epitaxial growth of materials with large lattice mismatch. In this review, the driving forces behind the formation of self-assembled oxide–metal VAN structures are discussed. Specifically, an updated in-plane strain compensation model based on the areal strain compensation concept has been proposed in this review, inspired by the prior linear strain compensation model. It provides a guideline for material selection for designing VAN systems, especially those involving complex orientation matching relationships. Based on the model, several case studies are discussed, comparing the microstructure and morphology of different oxide–metal nanocomposites by varying the oxide phase. Specific examples highlighting the coupling between the electrical, magnetic and optical properties are also discussed in the context of oxide–metal nanocomposites. Finally, future research directions and needs are also discussed.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Advanced Design and 3D Printing Strategies With Alginate‐Nanoclay Nanocomposites: From Microstructure to Bioprinting

Nanocomposites made from alginate and nanoclay are extensively applied for diverse biomedical applications. However, the lack of a clear understanding of the interactions between alginate and nanoclay makes it difficult to rationally design the nanocomposites for different material extrusion-based 3D bioprinting strategies. Here, a combined analytical model is proposed to accurately predict the interaction mechanisms between alginate and nanoclay through small-angle neutron scattering. These mechanisms are summarized into a phase diagram that can guide the design of alginate-nanoclay nanocomposites for different bioprinting applications. The rheological properties of various nanocomposites are measured to validate the proposed interaction mechanisms at the macroscale. Accordingly, three representative extrusion-based bioprinting strategies are linked with the nanocomposite design and applied to freeform fabricate complex structures. In conclusion, a roadmap is summarized to bridge the gap between biomaterial design and bioprinting processes, enabling the rapid and rational selection of biomaterial formula based on available 3D printing methods, and vice versa.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Enhanced Electrocatalytic and Cathode‐Electrolyte Interfacial Properties With a Pr‐Based Simple Perovskite/Ruddlesden‐Popper Nanocomposite Cathode in Protonic Ceramic Fuel Cells

The sluggish kinetics and poor stability of the oxygen reduction reaction (ORR) remain the primary bottleneck for achieving high performance in protonic ceramic fuel cells (PCFCs) at intermediate temperatures (400–650°C). In this work, a Pr-based nanocomposite cathode comprised of simple perovskite phase (PrNi 0.7 Co 0.3 O 3-δ ) and Ruddlesden-Popper phase (Co-doped Pr 4 Ni 3 O 10+δ ) is developed. Although PrNi 0.7 Co 0.3 O 3-δ solely stands as a good cathode with facile proton transfer, combining the superior catalytic activity against oxygen on the Ruddlesden-Popper phase boosts the ORR performance further. The designed nanocomposite cathode outperforms the simple perovskite cathode, attributed to enhanced oxygen absorption and surface diffusion with the Ruddlesden-Popper phase. A precursor-based cathode deposition technique is also developed to achieve cathode grain sizes of ∼100 nm. A single cell with the nanocomposite cathode delivers a peak power density of 1.38 W cm −2 at 650°C, among the highest in reported PCFCs with Pr-based cathodes, with a small degradation rate of 0.145 mV h −1 during 250 h stability test. Further investigation of cathode-electrolyte interface revealed interfacial PrO 2 phase formation, promoted by abundant Pr 6 O 11 in the nanocomposite precursor powder, thereby improving both ohmic resistance and stability. These findings highlight the effectiveness of the nanocomposite cathode and underscore its advantages on interfacial properties.

08 - HYDROGEN↗

DOE OSTI2022

Enhancement of effective thermal conductivity of rGO/Mg nanocomposite packed beds

Engineering thermophysical properties of metal hydrides nanocomposites is crucial for effective thermal management during hydrogen storage reactions; however, the effect of microstructure on thermal transport mechanisms is still unclear. Here, we employed an integrated experiment-modeling approach to investigate microstructural factors that determine the effective thermal conductivity of individual reduced graphene oxide-magnesium (rGO/Mg) nanocomposites and their packed bed. Here the effective thermal conductivity of the rGO/Mg nanocomposite packed bed was measured by using guarded hot-plate method under various atmospheric conditions (i.e., vacuum, Ar and He). A microstructure-aware mesoscopic modeling revealed that anisotropy of the effective thermal conductivity of individual rGO/Mg nanocomposites plays an important role in determining the effective thermal conductivity of their packed bed. The validated mesoscopic model also disclosed a nontrivial interplay between the intrinsic rGO properties and the extrinsic composite structural features. Finally, quantitative sensitivity analysis based on the modeling framework is used to provide practical engineering guidance for controlling the thermal transport within nanocomposite packed beds.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Templated Mesoporous Silica Outer Shell for Controlled Silver Release of a Magnetically Recoverable and Reusable Nanocomposite for Water Disinfection

Here, we encapsulated Fe 3 O 4 @SiO 2 @Ag (MS-Ag), a bifunctional magnetic silver core–shell structure, with an outer mesoporous silica (mS) shell to form an Fe 3 O 4 @SiO 2 @ 2 Ag@mSiO 2 (MS-Ag-mS) nanocomposite using a cationic CTAB (cetyltrimethylammonium bromide) micelle templating strategy. The mS shell acts as protection to slow down the oxidation and detachment of the AgNPs and incorporates channels to control the release of antimicrobial Ag + ions. Results of TEM, STEM, HRSEM, EDS, BET, and FTIR showed the successful formation of the mS shells on MS-Ag aggregates 50–400 nm in size with highly uniform pores ~4 nm in diameter that were separated by silica walls ~2 nm thick. Additionally, the mS shell thickness was tuned to demonstrate controlled Ag + release; an increase in shell thickness resulted in an increased path length required for Ag + ions to travel out of the shell, reducing MS-Ag-mS’ ability to inhibit E. coli growth as illustrated by the inhibition zone results. Through a shaking test, the MS-Ag-mS nanocomposite was shown to eradicate 99.99+% of a suspension of E. coli at 1 × 10 6 CFU/mL with a silver release of less than 0.1 ppb, well under the EPA recommendation of 0.1 ppm. This high biocidal efficiency with minimal silver leach is ascribed to the nanocomposite’s mS shell surface characteristics, including having hydroxyl groups and possessing a high degree of structural periodicity at the nanoscale or “smoothness” that encourages association with bacteria and retains high Ag + concentration on its surface and in its close proximity. Furthermore, the nanocomposite demonstrated consistent antimicrobial performance and silver release levels over multiple repeated uses (after being recovered magnetically because of the oxidation-resistant silica-coated magnetic Fe 3 O 4 core). It also proved effective at killing all microbes from Long Island Sound surface water. The described MS-Ag-mS nanocomposite is highly synergistic, easy to prepare, and readily recoverable and reusable and offers structural tunability affecting the bioavailability of Ag + , making it excellent for water disinfection that will find wide applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2021

Pore-Confined Polymers Enhance the Thermal Conductivity of Polymer Nanocomposites

In this work, molecularly confined polymer fillers in nanopores were found to give superior mechanical properties of polymer nanocomposites. In this work, we study the thermal conductivity of such nanocomposites and unveil the effect of polymer confinement on thermal conductivity. Using the time-domain thermoreflectance method, we measure the cross-plane thermal conductivity of polymer nanocomposites that consist of polystyrene fillers confined within a nanoporous organosilicate matrix. Compared to unconfined bulk polystyrene fillers, we find that pore-confined polystyrene fillers enhance the thermal conductivity of the polymer nanocomposites. This enhancement is attributed to the better aligned and less entangled chains in the confined phase, where chain–chain phonon scatterings are reduced. Our work provides essential insights into the thermal conductivity of polymer nanocomposites for multifunctional thermal and mechanical applications.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Development of Multi-Scale X-ray Fluorescence Tomography for Examination of Nanocomposite-Treated Biological Samples

Research in cancer nanotechnology is entering its third decade, and the need to study interactions between nanomaterials and cells remains urgent. Heterogeneity of nanoparticle uptake by different cells and subcellular compartments represent the greatest obstacles to a full understanding of the entire spectrum of nanomaterials’ effects. In this work, we used flow cytometry to evaluate changes in cell cycle associated with non-targeted nanocomposite uptake by individual cells and cell populations. Analogous single cell and cell population changes in nanocomposite uptake were explored by X-ray fluorescence microscopy (XFM). Very few nanoparticles are visible by optical imaging without labeling, but labeling increases nanoparticle complexity and the risk of modified cellular uptake. XFM can be used to evaluate heterogeneity of nanocomposite uptake by directly imaging the metal atoms present in the metal-oxide nanocomposites under investigation. While XFM mapping has been performed iteratively in 2D with the same sample at different resolutions, this study is the first example of serial tomographic imaging at two different resolutions. A cluster of cells exposed to non-targeted nanocomposites was imaged with a micron-sized beam in 3D. Next, the sample was sectioned for immunohistochemistry as well as a high resolution “zoomed in” X-ray fluorescence (XRF) tomography with 80 nm beam spot size. Multiscale XRF tomography will revolutionize our ability to explore cell-to-cell differences in nanomaterial uptake.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2021

Magnetically Recoverable and Reusable Titanium Dioxide Nanocomposite for Water Disinfection

A bifunctional magnetic Fe3O4@SiO2@TiO2 or MS-TiO2 antimicrobial nanocomposite was prepared based on simple sol-gel methods with common equipment and chemicals. Reaction pH was found to influence the TiO2 upload in the nanocomposite. The alkaline condition produced the greatest TiO2 upload, while the acidic condition the least. Annealing at 300 °C turned the as-synthesized amorphous TiO2 into one with high content of anatase, the most photoactive form of TiO2. Irradiated by 365 nm UV light, a sample of 30 mg/mL of annealed nanocomposite containing 12.6 wt.% Ti was shown to be able to completely eradicate 104 CFU/mL of the laboratory-grown E. coli within 25 min, 25 min faster than the control when the 365 nm UV light was employed alone. The nanocomposite demonstrated consistent antimicrobial performance over repeated uses and was easily recoverable magnetically due to its high magnetization value (33 emu/g). Additionally, it was shown to reduce the bacterial count in a real surface water sample containing 500–5000 CFU/mL of different microbes by 62 ± 3% within 30 min. The irradiating 365 nm UV light alone was found to have generated little biocidal effect on this surface water sample. The nanocomposite is promising to serve as an effective, safe, and eco-friendly antimicrobial agent, especially for surface water disinfection.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2025

Epoxy-based vitrimeric semi-interpenetrating network/MXene nanocomposites for hydrogen gas barrier applications

Herein, we report MXene-filled epoxy-based vitrimeric nanocomposites featuring a semi-interpenetrating network (S-IPN) to develop a hydrogen gas (H 2 ) barrier coating with self-healing characteristics for compressed H 2 storage applications. The reversible epoxy network was formed by synthesizing linear epoxy chains with pendent bis-hydroxyl groups using amino diol, which were then crosslinked with 1,4-benzenediboronic acid to generate dynamic boronic ester linkages. To achieve the S-IPN-type molecular arrangement, the epoxy chains were in situ crosslinked in the presence of poly(ethylene-co-vinyl alcohol) (EVOH), giving rise to a self-healing network (EEP) with a healing efficiency of 87%. Into the S-IPN vitrimer (EEP), a 2D platelet-type nanofiller MXene was incorporated to introduce a tortuous path for H 2 gas diffusion along with improved mechanical properties. The nanocomposite coating was applied to nylon 6 liner material, which is conventionally used in all-composite H 2 storage vessels. Further, the application of a 2 wt% MXene/EEP nanocomposite coating showed a permeability coefficient of 0.062 cm 3 mm m -2 d -1 atm -1 exhibiting ~96% reduction in gas permeability compared to uncoated nylon 6. The same nanocomposite exhibited a healing efficiency of 79%. Increasing the MXene loading to 10 wt% further reduced the permeability coefficient to 0.002 cm 3 mm m -2 d -1 atm -1 ; however, the healing efficiency decreased due to restricted chain mobility. In essence, the current work highlights the potential of vitrimeric S-IPN nanocomposite coatings for H 2 gas-barrier applications, enhancing safety and performance.

42 ENGINEERING↗

DOE OSTI2022

Synthesis and Characterization of Copolymers and Nanocomposites from Limonene, Styrene and Organomodified-Clay Using Ultrasonic Assisted Method

In the present work, we report a simple synthesis method for preparation of copolymers and nanocomposites from limonene and styrene using clay as a catalyst. The copolymerization reaction is carried out by using a proton exchanged clay as a catalyst called Mag-H+. The effect of temperature, reaction time and amount of catalyst were studied, and the obtained copolymer structure (lim-co-sty) is characterized by Fourier transform infrared spectroscopy (FT-IR), nuclear magnetic resonance spectroscopy (1H-NMR) and differential scanning calorimetry (DSC). The molecular weight of the obtained copolymer is determined by gel permeation chromatography (GPC) and is about 4500 g·mol−1. The (lim-co-sty/Mag 1%, 3%, 7% and 10% by weight of clay) nanocomposites were prepared through polymer/clay mixture in solution method using ultrasonic irradiation, in the presence of Mag-CTA+ as green nano-reinforcing filler. The Mag-CTA+ is organophilic silicate clay prepared through a direct exchange process, using cetyltrimethylammonuim bromide (CTAB). The prepared lim-co-sty/Mag nanocomposites have been extensively characterized by FT-IR spectroscopy, X-ray diffraction (XRD), scanning electronic microscopy (SEM) and transmission electronic microscopy (TEM). TEM analysis confirms the results obtained by XRD and clearly show that the obtained nanocomposites are partially exfoliated for the lower amount of clay (1% and 3% wt) and intercalated for higher amounts of clay (7% and 10% wt). Moreover, thermogravimetric analysis (TGA) indicated an enhancement of thermal stability of nanocomposites compared with the pure copolymer.

Derdar, Hodhaifa↗

NASA NTRS2003

Functional nanocomposites prepared by self-assembly and polymerization of diacetylene surfactants and silicic acid

Conjugated polymer/silica nanocomposites with hexagonal, cubic, or lamellar mesoscopic order were synthesized by self-assembly using polymerizable amphiphilic diacetylene molecules as both structure-directing agents and monomers. The self-assembly procedure is rapid and incorporates the organic monomers uniformly within a highly ordered, inorganic environment. By tailoring the size of the oligo(ethylene glycol) headgroup of the diacetylene-containing surfactant, we varied the resulting self-assembled mesophases of the composite material. The nanostructured inorganic host altered the diacetylene polymerization behavior, and the resulting nanocomposites show unique thermo-, mechano-, and solvatochromic properties. Polymerization of the incorporated surfactants resulted in polydiacetylene (PDA)/silica nanocomposites that were optically transparent and mechanically robust. Molecular modeling and quantum calculations and (13)C spin-lattice relaxation times (T(1)) of the PDA/silica nanocomposites indicated that the surfactant monomers can be uniformly organized into precise spatial arrangements prior to polymerization. Nanoindentation and gas transport experiments showed that these nanocomposite films have increased hardness and reduced permeability as compared to pure PDA. Our work demonstrates polymerizable surfactant/silica self-assembly to be an efficient, general approach to the formation of nanostructured conjugated polymers. The nanostructured inorganic framework serves to protect, stabilize, and orient the polymer, mediate its performance, and provide sufficient mechanical and chemical stability to enable integration of conjugated polymers into devices and microsystems.

NASA Discipline Life Support Systems↗