Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microscale additive manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Effect of microstructure on fatigue crack propagation in additive manufactured nickel-based superalloy Haynes 282: an experiment and crystal plasticity study

Haynes 282 is a γ' precipitation-strengthened nickel-based superalloy known for its exceptional high-temperature creep resistance and excellent fabricability. Recent advancements in powder-bed fusion-based additive manufacturing (PBF-AM) have enabled the fabrication of Haynes 282 with accurate, site-specific control of the grain orientation and morphology at the microscale. This ability opens up new avenues for microstructure design, to improve the material’s fatigue crack resistance and service life. This paper investigates the fatigue crack growth behavior of hybrid microstructure Haynes 282 fabricated via PBF-AM. Previous experiments revealed a higher crack propagation rate in the coarse columnar-grained microstructural regions when compared against fine-grained areas. Here, a strain gradient crystal plasticity model was adapted to study the fracture-related mechanical fields at the crack tip in the two microstructures. The simulation results showed a consistent influence of grain structure and texture on crack propagation, as was seen in the experiment. The model analysis revealed higher crack propagation driving force along crack direction in the coarse-grained sharply textured microstructure and higher driving force for crack kinking in fine-grained more diffusely textured microstructure, which is ascribed to the combined effect of yield stress, hardening rate, texture and grain morphology. The presented modeling approach will facilitate the development of the AM-based accurate microstructure design by deepening the fundamental study in AM-specific microstructure-properties relations.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Additive manufacturing enabled synergetic strengthening of bimodal reinforcing particles for aluminum matrix composites

An additive manufactured TiB 2 /Al-Cu-Mg-Ni composite with a minor amount of Sc was fabricated by laser powder bed fusion (LPBF). The composite shows a yield strength of ~370 MPa, almost doubling the strength of its wrought matrix counterpart, and an elongation of ~7 %. The superior mechanical properties are attributed to a unique micro-nano hierarchical microstructure, consisting of nanoscale and microscale TiB 2 particles dispersed in a matrix of fine aluminum grains (3 µm) together with intragranular intermetallic nanoparticles and nano-cellular networks (cell size 30 nm). The formation of the TiB 2 nanoparticles is the consequence of partial dissolution of the TiB 2 particulates and the enrichment of Sc in the newly formed nanoparticles. Remarkable strengthening effects are achieved by the bimodal TiB 2 particles, intermetallic nanoparticles and intragranular nano-cellular networks. Finally, this study provides new insights into the role of additive manufacturing in tailoring the microstructure of particulate reinforced metal matrix composites (MMCs) with advanced properties.

36 MATERIALS SCIENCE↗
DOE OSTI2022

An additively-manufactured molten salt-to-supercritical carbon di-oxide primary heat exchanger for solar thermal power generation – Design and techno-economic performance

The design and techno-economic performance of a compact additively manufactured (AM) molten salt (MS)-to-supercritical carbon di-oxide (sCO2) primary heat exchanger (PHE) for solar thermal application is described. The PHE design consists of sCO2 flow through an array of microscale pin fins while the MS flows through mm-scale rectangular channels. Constraints imposed by AM using laser powder bed fusion method are considered in the design. Structural and fluid flow simulations are performed to arrive at a viable design of the core and headers. A simplified one-dimensional steady state model for the PHE is developed including the impact of surface roughness from the AM process. A process-based cost model is used to determine the tradeoff between thermofluidic design and manufacturing cost. A parametric study is performed using the thermo-fluidic and cost models to determine the set of geometrical and flow variables that result in high power density and low cost, while restricting the pressure drop on the sCO2 side to less than 2% of line pressure. Flow rates of MS and sCO2 were varied over heat capacity rate ratios ranging from 0.2 to 1. Results indicate that it is possible to design a low-pressure drop AM PHE with an effectiveness of 90% and a power density in excess of 10 MW/m3 (including headers). Fabrication of representative nickel superalloy specimens are shown to demonstrate that low-porosity parts with the requisite dimensional tolerance of PHE core can be generated.

14 SOLAR ENERGY↗
DOE OSTI2026

Ultrafast Reactive Laser Sintering of Highly Conductive Garnet-Type LLZTO Solid Electrolytes

Rapid and scalable fabrication of garnet-type solid electrolytes remains a major challenge for the practical deployment of lithium metal batteries. Here, we report reactive laser sintering (RLS) as an ultrafast and potentially scalable strategy for fabricating garnet-type Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 (LLZTO) solid electrolytes. RLS of LLZTO enables simultaneous reaction and densification, achieving ∼95% relative density while minimizing lithium loss and suppressing secondary phase formation. Compared to conventional furnace sintering, RLS promotes enhanced grain growth and improved densification, leading to improved ionic conductivity (0.36 ± 0.08 mS cm −1 ) while maintaining comparable activation energies for Li + transport. Structural characterization by X-ray diffraction (XRD), Raman spectroscopy, and solid-state 6 Li/ 7 Li NMR confirms the formation of cubic garnet LLZTO with homogeneous microscale elemental distribution. In addition, nanoindentation measurements demonstrate that RLS preserves the mechanical properties of the garnet framework despite ultrafast localized thermal processing. By integrating simultaneous reaction and densification with tunable microstructural control, reactive laser sintering provides a promising manufacturing pathway for high-performance garnet solid electrolytes toward next-generation solid-state batteries.

CO2 laser↗
DOE OSTI2024

Digital Multiphase Composites via Additive Manufacturing

Abstract Mechanical properties of traditional engineering materials are typically coupled to each other, presenting a challenge to practitioners with multi‐dimensional material property requirements. In this work, continuous, independent control over multiple mechanical properties is demonstrated in composite materials realized using additive manufacturing. For the first time, composites additively manufactured from rigid plastic, soft elastomer, and liquid constituents are experimentally characterized, demonstrating materials which span four orders of magnitude in modulus and two orders of magnitude in toughness. By forming analytical mappings between relative concentrations of constituents at the microscale and resulting macroscale material properties, inverse material design is enabled; the method is showcased by printing artifacts with prescribed toughness and elasticity distributions. The properties of these composites are placed in the context of biological tissues, showing they have promise as mechanically plausible tissue mimics.

Smith, Lawrence T.↗
DOE OSTI2025

Effect of Loading Frequency on Fatigue Behavior of Additively Manufactured Short Fiber Thermoplastics via Infrared Thermography

Fracture, Fatigue, Failure, Damage Evolution and Thermomechanics & Infrared Imaging, Volume 4 of the Proceedings of the 2025 SEM Annual Conference & Exposition on Experimental and Applied Mechanics, the fourth volume of five from the Conference, brings together contributions to this important area of research and engineering. The collection presents early findings and case studies on a wide range of areas, including: • 3D Deformation and Failure • In-situ Techniques and Microscale Effects on Mechanical Behavior • Vibration and Cyclic Fatigue • Integration of Models and Experiments • Interface-Mediated Damage and Failure • Fracture and Fatigue in Brittle Materials • Material Characterizations Using Thermography • Fatigue, Damage & Fracture Evaluation Using Infrared Thermography

Pathak, Pharindra [Auburn University]↗
DOE OSTI2023

Use of latent metathesis polymerization systems for photopolymerization-based additive manufacturing

Photolatent olefin metathesis catalysts can be used in combination with metathesis-active monomers or resins for photopolymerization-based additive manufacturing via ring-opening metathesis polymerization (ROMP). A variety of alternative catalysts and photosensitizers are commercially available that allows for tuning of thermomechanical properties, potlifes, activation rates, and irradiation wavelengths. As an example, two optimized catalyst/photosensitizer systems were demonstrated in the rapid stereolithographic printing of complex, multidimensional poly-dicyclopentadiene structures with microscale features under ambient conditions.

Leguizamon, Samuel↗
DOE OSTI2020

Three-dimensional hierarchical nanoporous copper via direct ink writing and dealloying

Three-dimensional (3D) hierarchical nanoporous Cu (3DHNP-Cu) is synthesized using a combination of direct ink writing (DIW) based 3D printing, thermal sintering, and chemical dealloying of Mn–Cu alloys. Through tuning processing conditions such as ink composition and cooling rate (after sintering), with consideration of Mn loss during sintering, 3DHNP-Cu with fully bicontinuous nanostructures and negligible residual Mn can be produced after dealloying. The 3DHNP-Cu is comprised of structural features that span seven orders of magnitude, where DIW digitally controls macroscale porous features, thermal sintering and degradation of the binding polymer determines microscale porous features, and dealloying gives rise to nanoscale pores.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tailoring the coefficient of thermal expansion of ternary nickel alloys through compositional control and non-contact measurements

The majority of microelectromechanical systems (MEMS) are made of silicon, however, future applications will be used in extreme environments, especially at elevated temperatures, and require materials with enhanced properties. Use of metal alloys in these applications will require microscale manufacturability, a balance of physical and mechanical properties and dimensional stability. Here in this paper, we emphasized dimensional stability by reducing the coefficient of thermal expansion (CTE) and present an optical non-contact method for measuring the thermal expansion of planar thin films. A combinatorial approach was employed to determine the CTE of nickel-molybdenum-tungsten (Ni-Mo-W) sputter deposited films over a range of compositions, and the addition of Mo and W is shown to significantly decrease and provide a route for tailoring the CTE with compositional control. Ni-Mo-W alloys were revealed to have CTE values ranging from 8–12 × 10 -6 /°C, matching that of commercial glass substrates that are employed in numerous MEMS devices.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Shock compression of additively manufactured high solids loaded polymer composites with aligned porosity

The effects of aligned porosity on the shock-compression response of additively manufactured (AM) composite structures with collinear and log-cabin geometries are investigated. The composites contain two inorganic and two organic particle populations and a UV-curable polymer binder. X-ray phase contrast imaging (X-PCI) is used as an in-material diagnostic in plate-impact experiments performed at the Dynamic Compression Sector of the Advanced Photon Source at the Argonne National Laboratory. Macroscale shock and particle velocities and microscale pore collapse velocities are measured from X-PCI images obtained from samples impacted in various orientations relative to the AM build directions. The linear shock and particle velocity relation for the structures with collinear build geometry shows directional differences, with the build direction exhibiting the highest slope and the filament print direction having the shallowest slope. Composites with log-cabin geometry, due to their slightly lower porosity and smaller sized pores, show higher shock velocities than the collinear structures at the same particle velocity. Microscale directionality effects are also observed, with the pore collapse velocity dependent on the pore configuration. Specifically, the pore collapse velocity is highest for pores elongated along the impact direction which is the case for the colinear structures impacted in the filament print direction, which is consistent with the directionality trend observed in the data for the shock and particle velocity equation of state. The pore collapse velocity approaches ∼80 % of the shock velocity and is several times the average bulk particle velocity, suggesting a highly hydrodynamic mechanism of pore collapse. Overall, both the macroscale response as measured by the shock and particle velocity relationship, and the microscale response as measured by the pore collapse velocity, are found to be anisotropic and dependent on the AM composite structure.

Wagner, K. B. [Georgia Institute of Technology, At↗
DOE OSTI2025

Modeling low cycle fatigue (LCF) of additively manufactured Hastelloy X using An accelerated crystal plasticity fatigue damage model

This paper presents a microstructure-based model for low cycle fatigue (LCF) behavior and life of Nickel-based alloy Hastelloy X manufactured using laser-powder bed fusion (L-PBF) additive manufacturing (AM). AM Hastelloy X, a solution-strengthened alloy, is tested at elevated temperature under fully reversed LCF conditions at different strain levels. A generalized plane strain finite element model is generated from electron backscatter diffraction (EBSD) characterization. The constitutive behavior of the material under fatigue is modeled using crystal plasticity and calibrated with both monotonic tensile and cyclic stress–strain data. The fatigue micro-crack initiation and propagation in the microstructure is modeled using a modified Chaboche fatigue damage model. An embedded boundary condition with a homogenous medium is used to apply the cyclic deformation and prevent numerically introduced over-constraints during fatigue simulation. A ‘cycle-jump’ method is used to accelerate the fatigue simulation and reduce the computational cost. The simulation results are compared to LCF experiments, showing satisfactory matches in cyclic stress behavior and number of cycles to macro-crack initiation for all applied strain ranges. In addition, the model illustrates the potential for quantifying microscale fatigue life impacting factors such as microstructure and surface roughness, which is needed to accurately quantify the reliability of AM components in service.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Manufacturing of Continuous Core–Shell Hydrated Salt Fibers for Room Temperature Thermal Energy Storage

The encapsulation of salt hydrate phase change materials (PCMs) in uniform microscale bodies has yet been reported in research due in part to the delicate relationship between thermal performance and water-to-salt ratios which are easily altered during manufacturing. Herein, core–shell composite fibers comprised of a salt hydrate PCM core and a poly(acrylonitrile) (PAN) shell are wet spun in a continuous process using a syringe pump and coaxial die. The PCM phase comprises calcium chloride hexahydrate (CaCl 2 ·6H 2 O) with strontium chloride hexahydrate(SrCl 2 ·6H 2 O) (3 wt%) and fumed silica(SiO 2 ) (2 wt%) as additive, a composition that is prepared from homogenous melt at 40 °C. 15 wt% PAN in dimethylsulfoxide solvent is used to prepare the shell-forming polymer gel. PCM and polymer gel injection rates of 10–40 mL h –1 are used to spin coaxial fibers through a coagulation bath, yielding continuous microtubules with diameters in the range of 850–1500 μm. Cyclic testing shows that after 1000 cycles, melting enthalpies incurred only a 3.5% decline from 131.46 to 126.9 J g –1 . In conclusion, success here overcomes several coincidental drawbacks of PCM fiber performance and manufacturing and delivers the first example of scalable roll-to-roll PCM fiber produced by wet spinning for building material applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High-throughput printing of combinatorial materials from aerosols

The development of new materials and their compositional and microstructural optimization are essential in regard to next-generation technologies such as clean energy and environmental sustainability. However, materials discovery and optimization have been a frustratingly slow process. The Edisonian trial-and-error process is time consuming and resource inefficient, particularly when contrasted with vast materials design spaces 1 . Whereas traditional combinatorial deposition methods can generate material libraries 2,3 , these suffer from limited material options and inability to leverage major breakthroughs in nanomaterial synthesis. Here we report a high-throughput combinatorial printing method capable of fabricating materials with compositional gradients at microscale spatial resolution. In situ mixing and printing in the aerosol phase allows instantaneous tuning of the mixing ratio of a broad range of materials on the fly, which is an important feature unobtainable in conventional multimaterials printing using feedstocks in liquid–liquid or solid–solid phases 4–6 . We demonstrate a variety of high-throughput printing strategies and applications in combinatorial doping, functional grading and chemical reaction, enabling materials exploration of doped chalcogenides and compositionally graded materials with gradient properties. The ability to combine the top-down design freedom of additive manufacturing with bottom-up control over local material compositions promises the development of compositionally complex materials inaccessible via conventional manufacturing approaches.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The role of micro-inertia on the shock structure in porous metals

The behavior of porous materials under shock loading is a multi-scale problem bridging orders of magnitude across the macroscale geometry and the microscale pores. Under static loading, this problem is well understood, relating mechanisms of pore closure and crushing to the equivalent macroscale models. The dynamic response of porous solids under shock loading is related to the effects of viscoplasticity and micro-acceleration fields around the void boundaries. The significance of the micro-inertia effects in modeling the dynamic behavior of porous materials remains an open question. In this work, an experimental investigation on closed-cell porous aluminum with small porosity provides the evidence for the first time of micro-inertia’s fundamental role in describing the shock structure in these materials. Materials with different levels of porosity were manufactured using a modified process of additive manufacturing to achieve a mean pore size below 50$\mu$m. Plate impact experiments on porous aluminum samples were conducted at pressures in the range of 2 to 11 GPa. The structure of the steady shock was characterized as a function of porosity and shown to validate behavior revealed by an analytical approach (Czarnota et al. [J. Mech. Phys. Solids 107 (2017)]), highlighting the fundamental role of micro-inertia effects in such cases.

36 MATERIALS SCIENCE↗
DOE OSTI2021

AFRL Additive Manufacturing Modeling Series: Challenge 4, In Situ Mechanical Test of an IN625 Sample with Concurrent High-Energy Diffraction Microscopy Characterization

In this work, we describe 3D characterization of an additively manufactured Inconel 625 nickel-base superalloy specimen conducted during a uniaxial tension test using a suite of nondestructive x-ray techniques. High-energy diffraction microscopy in both near- and far-field modalities are employed in situ to track evolution of the material orientation and stress–strain fields at six points during the mechanical test, and these data streams are registered with micro-computed tomography reconstructions which probe the material density. This data volume was matched to a multi-modal serial sectioning characterization of the specimen taken after loading, described in this article’s companion. Twenty-eight grains which were monitored throughout the experiment were selected to form the basis for AFRL AM Modeling Series Challenge 4, Microscale Structure-to-Properties.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Tusas: A fully implicit parallel approach for coupled phase-field equations

In this study, we develop a fully-coupled, fully-implicit approach for phase-field modeling of solidification in metals and alloys. Predictive simulation of solidification in pure metals and metal alloys remains a significant challenge in the field of materials science, as microstructure formation during the solidification process plays a critical role in the properties and performance of the solid material. Our simulation approach consists of a finite element spatial discretization of the fully-coupled nonlinear system of partial differential equations at the microscale, which is treated implicitly in time with a preconditioned Jacobian-free Newton-Krylov method. The approach is algorithmically scalable as well as efficient due to an effective preconditioning strategy based on algebraic multigrid and block factorization. We implement this approach in the open-source Tusas framework, which is a general, flexible tool developed in C++ for solving coupled systems of nonlinear partial differential equations. The performance of our approach is analyzed in terms of algorithmic scalability and efficiency, while the computational performance of Tusas is presented in terms of parallel scalability and efficiency on emerging heterogeneous architectures. We demonstrate that modern algorithms, discretizations, and computational science, and heterogeneous hardware provide a robust route for predictive phase-field simulation of microstructure evolution during additive manufacturing.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Multi‐Material Gradient Printing Using Meniscus‐enabled Projection Stereolithography (MAPS)

Light‐based additive manufacturing methods are widely used to print high‐resolution 3D structures for applications in tissue engineering, soft robotics, photonics, and microfluidics, among others. Despite this progress, multi‐material printing with these methods remains challenging due to constraints associated with hardware modifications, control systems, cross‐contamination, waste, and resin properties. Here, a new printing platform coined Meniscus‐enabled Projection Stereolithography (MAPS) is reported, a vat‐free method that relies on generating and maintaining a resin meniscus between a crosslinked structure and bottom window to print lateral, vertical, discrete, or gradient multi‐material 3D structures with no waste and user‐defined mixing between layers. MAPS is compatible with a wide range of resins shown and can print complex multi‐material 3D structures without requiring specialized hardware, software, or complex washing protocols. MAPS's ability to print structures with microscale variations in mechanical stiffness, opacity, surface energy, cell densities, and magnetic properties provides a generic method to make advanced materials for a broad range of applications.

bioprinting↗