Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microfracture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Rayleigh wave studies in lunar rocks.

An ultrasonic surface wave technique described by the author (1971) is used to verify a hypothesis that links the seismic wave propagation velocities in lunar crust, much too low as compared to those on earth, to the extensive fracturing of lunar rock in the absence of liquids and gases which changed drastically the elastic and inelastic properties of lunar rock. Measurements on lunar rock samples and synthetic analogs suggest that the presence of microfractures have influence on both the wave velocity and Q factor in lunar rocks.

Tittmann, B. R.↗
NASA NTRS1972

Thermal expansion of Apollo lunar samples and Fairfax diabase.

Measured values of the thermal expansion of seven Apollo samples over the temperature range -100 C to +200 C are reported and compared to terrestrial Fairfax diabase. For most of the lunar rocks the measured expansion is significantly lower (30%) than the intrinsic value calculated from Turner's equation for the thermal expansion of an aggregate. The measured expansion of the Fairfax diabase was equal to the intrinsic but was higher for samples of Fairfax which had been previously cycled to high temperatures. The effect of microfractures on the thermal expansion of rocks is discussed.

Baldridge, W. S.↗
NASA NTRS1973

Effects of thermal loading on fiber-reinforced composites with constituents of differing thermal expansivities.

Estimates of the magnitudes of elastic stresses and elastoplastic stresses and strains were made for tungsten fiber-reinforced 80Ni + 20Cr matrix composites. Heating or cooling between 80 and 2000 F was assumed. The calculated elastic stresses exceeded representative or estimated strengths of constituents. For composites with less than 0.65 volume fraction of fiber, plastic flow was considered possible, and elastoplastic solutions indicated that stresses would be reduced but with the concomitant occurrence of sufficiently large strain ranges, particularly in the matrix, to pose a possible thermal fatigue problem. Limited experimental studies on tungsten fiber-copper matrix composites heated and cooled a number of times between 80 and 1600 F in a conventional furnace and then heated from 80 to 1652 F in a hot-stage microscope resulted in matrix microfracture for a 70 volume fraction fiber composite and substantial matrix strain for a 40 volue fraction fiber composite.

Hoffman, C. A.↗
NASA NTRS1974

Internal friction in rocks and its relationship to volatiles on the moon

The physical properties of lunar rocks were measured using the vibrating bar technique in order to provide data for interpretation of geophysical results such as those from seismic measurements. The effect of volatiles on the mechanical Q in lunar rocks was studied in addition to the effect of exposing a sample to controlled amounts of those gases most likely to be present in the lunar environment or likely to have been outgassed from the lunar interior. The moderate temperatures to which the sample was exposed during the thermal treatment and the small drop in resonant frequency during the course of the outgassing suggests that there was little change in microfracture density. The frequency, composition and texture dependence of the damping were investigated, to study the loss mechanism.

Tittmann, B. R.↗
NASA NTRS1975

Application of Skylab imagery to some geological and environmental problems in Italy

Four topics are considered: regional geology of Sicily, volcanic surveillance in southern Italy, hydrogeology (with special regard given to the discovery and mapping of paleoriverbeds), and crop investigation. The discovery of unknown lineaments and structures in Sicily contributes to the geological knowledge of this region and in particular to the mechanical phenomena involving the upper part of the crust. An attempt was made to relate the status of vegetation surrounding Etna volcano to the magmatic gas escapes filtering through the soil. False-color Skylab images were used to analyze the vigor of the Etnean forestal belt vegetation canopy in order to map possible gas-vent ways as well as the 'active' microfractures. In northern Italy, buried channels were mapped in the Venetian Plain, and a tentative cost-benefit evaluation was done in the field of vegetational studies, both disease detection and species inventory were performed in the Po River Delta and in northwestern Italy.

Cassinis, R.↗
NASA NTRS1978

Pulse-echo probe of rock permeability near oil wells

Processing method involves sequential insonifications of borehole wall at number of different frequencies. Return signals are normalized in amplitude, and root-mean-square (rms) value of each signal is determined. Values can be processed to yield information on size and number density of microfractures at various depths in rock matrix by using averaging methods developed for pulse-echo technique.

Narasimhan, K. Y.↗
NASA NTRS1978

Characteristics of microcracks in samples from the drill hole Noerdlingen 1973 in the Ries crater, Germany

Samples from the Noerdlingen 1973 drill core contain abundant shock-induced microfractures which exhibit varying amounts of healing and sealing. Many of the microcracks resemble morphologically the open microcracks present in returned lunar samples. Data derived from petrography, scanning electron microscopy, and differential strain analysis indicate that fewer microcracks were formed at greater depths and crack sealing processes are more effective for cracks associated with planar elements. Although the microcracks in the Ries core are now sealed, they are valid analogues of the open shock-induced cracks of lunar rocks and demonstrate that open cracks do form in rocks at depth during a naturally-occurring shock event. The healing of the shock-induced cracks in the Ries core also precludes their use for laboratory measurements of physical properties intended to be used as analogue measurements of lunar samples in situ.

Padovani, E. R.↗
NASA NTRS1980

Clouding of pyroxene and plagioclase in eucrites - Implications for post-crystallization processing

The clouding of pyroxene and plagioclase in the basaltic eucrites ALHA 77302, Juvinas, Pasamonte, and Stannern, is caused by finely disseminated inclusions. This clouding is interpreted to be the result of exsolution of minor components which became incompatible and crystallized on microfractures and other nucleation sites during postbrecciation metamorphism. The phases found in clouding require reduction of silicate FeO to metallic Fe in both pyroxene and plagioclase and possible redox of Cr(2+) to Cr(3+) in pyroxene. The assemblage of coexisting phases that make up clouding record conditions of T approximately equal to 900 C and f(O2) of 10 to the -16th to 10 to the -18th during slow cooling. Thus, clouding can be a useful indicator of postcrystallization conditions.

Harlow, G. E.↗
NASA NTRS1985

Coal-Face Fracture With A Two-Phase Liquid

In new method for mining coal without explosive, two-phase liquid such as CO2 and water, injected at high pressure into deeper ends of holes drilled in coal face. Liquid permeates coal seam through existing microfractures; as liquid seeps back toward face, pressure eventually drops below critical value at which dissolved gas flashvaporizes, breaking up coal.

Collins, E. R., Jr.↗
NASA NTRS1985

Thermal history of shock-compressed solids

An isotropic, heterogeneous, viscous thermoplastic model of the uniaxially shock-compressed state in transparent solids is examined with a view to determining the conditions under which this radiation may be nominally thermal or nonthermal. Regions of locally high temperatures producing thermal radiation may develop only where the local viscosity is low and the Maxwell time is short; alternatively, regions of low elastic moduli and long Maxwell time could experience sustained elastic deformation, leading to microfracture and triboluminescence. Attention is given to the cases of MgO and SiO2.

Svendsen, B.↗
NASA NTRS1989

Ductile-regime turning of germanium and silicon

Single-point diamond turning of silicon and germanium was investigated in order to clarify the role of cutting depth in coaxing a ductile chip formation in normally brittle substances. Experiments based on the rapid withdrawal of the tool from the workpiece have shown that microfracture damage is a function of the effective depth of cut (as opposed to the nominal cutting depth). In essence, damage created by the leading edge of the tool is removed several revolutions later by lower sections of the tool edge, where the effective cutting depth is less. It appears that a truly ductile cutting response can be achieved only when the effective cutting depth, or critical chip thickness, is less than about 20 nm. Factors such as tool rake angle are significant in that they will affect the actual value of the critical chip thickness for transition from brittle to ductile response. It is concluded that the critical chip thickness is an excellent parameter for measuring the effects of machining conditions on the ductility of the cut and for designing tool-workpiece geometry in both turning and grinding.

Blake, Peter N.↗
NASA NTRS1988

Growth and characterization of large YBa2Cu3O(7-x) single crystals

Centimeter-sized crystal plates of YBa2Cu3O(7-x) have been obtained using a bulk composition and method described by Schneemeyer at al. (1987) modified for growth in a pure oxygen atmosphere. A porous MgO crucible and long soak time promote large crystals. Mg was not detectable in the crystals. Electron microbeam analysis using a 60 A monochromator crystal for the oxygen determination gave the composition Y(1.05)Ba(2.02)Cu(2.94)O(6.52 + or - 0.06). As-grown crystals from the melt surface exhibit a fairly sharp Tc with zero resistance at 80 K, and show complex twinning and crack patterns. Optical micrographs of a lightly polished surface normal to the c-axis of a 3-mm crystal delineate twinning and fine scale microcracking; this crystal surface now has a zero resistance at 68 K. Microhardness measurements and microfracture observations indicate intrinsic properties that may inhibit or impede large scale manufacture of electronic ceramics.

Keester, Kenneth L.↗
NASA NTRS1989

Indentation fracture toughness of sintered silicon carbide in the Palmqvist crack regime

The fracture toughness of a sintered dense alpha-SiC was estimated by the Vickers indentation microfracture method in the low-load Palmqvist crack regime. It was observed that the use of simultaneously obtained Vickers hardnesses does not yield reliable fracture toughness values, nor does application of the median-crack-derived equations. It is necessary to utilize a load-independent, crack-free hardness value with this toughness estimation method. Although several of the curve-fitting equations yield similar toughnesses, it is concluded for the Palmqvist crack system in this alpha-SiC that the Niihara-Morena-Hasselman (1982) equation is the only one which yields fracture toughness values in agreement with conventional measurement techniques.

Li, Zhuang↗
NASA NTRS1990

The equivalence between dislocation pile-ups and cracks

Cracks and dislocation pile-ups are equivalent to each other. In this paper, the physical equivalence between cracks and pile-ups is delineated, and the relationshps between crack-extension force, force on the leading dislocation, stress-intensity factor, and dislocation density are reviewed and summarized. These relations make it possible to extend quantitatively the recent advances in the concepts and practices of fracture mechanics to the studies of microfractures and microplastic deformations.

Liu, H. W.↗
NASA NTRS1990

Characterization of the tip field of a discrete dislocation pileup for the development of physically based micromechanics

It is shown, on the basis of calculations by Eshelby et al. (1951), Armstrong et al. (1966), and Chou and Li (1969), that a single parameter, such as the force on the leading dislocation (F), the crack extension force, or the stress intensity factor, is capable of characterizing uniquely the entire tip field of a discrete dislocation pileup, including the positions of mobile dislocations behind the locked leading dislocation at the tip. Conversely, the position of the i-th mobile dislocation X(i) is related to the value of F and is capable of characterizing the entire stress, strain, and displacement fields at the tip of a discrete dislocation pileup. If the interactions between dislocations are linear elastic, the measured positions of the mobile dislocations can be used to determine the value of F, which can then be used as a quantitative measure of the strength of a dislocation barrier resisting the propagation of a microslip or the nucleation of a microfracture.

Gao, Q.↗
NASA NTRS1991

Computational simulation of high temperature metal matrix composite behavior

Computational procedures are described to simulate the thermal and mechanical behavior of high temperature metal matrix composite (HT MMC) in the following four broad areas: (1) behavior of HT MMC from micromechanics to laminate; (2) HT MMC structural response for simple and complex structural components; (3) HT MMC microfracture; and (4) tailoring of HT MMC behavior for optimum specific performance. Representative results from each area are presented to illustrate the effectiveness of the computational simulation procedures. Relevant reports are referenced for extended discussion regarding the specific area.

Murthy, Pappu L. N.↗
NASA NTRS1990

Computational technology for flight vehicles; Proceedings of the Symposium, Washington, DC, Nov. 5-7, 1990

Recent advances in computational fluid mechanics are discussed in reviews and reports. Sections are devoted to (1) the modeling of local phenomena and edge effects in solids, (2) stochastic modeling and simulation of fracture toughness, and (3) partitioning strategy and new finite elements. Particular attention is given to global and local finite-element/spectral-boundary-element techniques for failure analysis, simulations of microfracture in metal-matrix composites, fatigue analysis of cracked anisotropic plates under stochastic loading, mathematical modeling for the analysis of nonlinear aircraft dynamics, physical and mathematical modeling of wave propagation in the Ariane 5 VEB structure, partitioning based on symmetry transformations, an FEM approach to adaptive reliability assurance, and time-domain FEMs for the large rotational dynamics of multibody systems.

Noor, Ahmed K.↗