SEARCH · Engineering Papers

Results for “method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Low energy neutron light output characterization of EJ301D and deuterated stilbene with a comparison of light output characterization methods

The neutron-induced light yield of a 2.54 cm diameter by 2.54 cm long right circular cylinder of EJ301D and a (5.08 cm)3 custom made cube of deuterated trans-stilbene-d12 (d-stilbene) were measured over incident neutron energies from 300 keV to 2.2 MeV and 200 keV to 2.4 MeV, respectively. The measurements were performed using a time-of-flight experiment with a Cf-252 source and an approximately 1.5 m flight path. We compare three light output spectrum full energy deposition edge estimation methods: (1) simulating the neutron energy spectrum edge and fitting it to the light output spectrum, (2) using the inflection point of the light output spectrum edge (derivative method, a.k.a. Kornilov’s method), and (3) using an empirical model fit to the edge of the light output spectrum. Both the derivative and equation fit methods do not account for physical processes such as multiple neutron scattering in the detectors. They instead rely on assumptions about the linear shape continuum shape of the light output spectrum and the direct correlation between the location of the spectrum’s inflection point and maximum energy deposition. These assumptions were found to introduce bias into those methods when tested against simulated spectra with known edge locations. When tested against measured spectra the derivative method was found to differ from the simulation fit by greater than 30% at low energies with large discontinuities for adjacent data points above 800 keV incident neutron energy. The empirical equation fitting method was found to also exhibit bias of a similar magnitude, but with significantly more continuous behavior, especially with the lower count data of the smaller volumed EJ301D scintillator. Experimental light output yield for this neutron energy range is reported using the simulated spectrum fitting method because it includes physics neglected by the other methods, and did not exhibit the bias observed in the other methods

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2024

Materials Characterization, Prediction, and Control Project: Characterization of 316L Stainless Steel after Solid Phase Processing using Ultrasonic NDE Method

The Pacific Northwest National Laboratory undertook the Materials Characterization, Prediction, and Control Laboratory Directed Research and Development Project to advance understanding of nuclear material processing and enable multifold acceleration in the development and qualification of new material systems produced via advanced manufacturing methods, such as solid phase processing, for use in national security and advanced energy applications (Smith 2021). A motivation of the Materials Characterization, Prediction, and Control Project was to demonstrate ultrasonic testing as a nondestructive evaluation method to complement traditional destructive methods for characterizing material microstructure with emphasis on grain size determination using a method that may have future applications for real-time inline process monitoring. The objective of the work described in this report is to establish the process and an analysis method for measuring grain sizes of polycrystalline metals with ultrafine grains using ultrasonic shear wave backscattering, building on prior studies on coarser-grained material. The work involves five tasks: Measured ultrasonic backscattering experimentally for a series of 316L stainless steel specimens with various grain sizes made by friction stir processing. Calculated ultrasonic backscattering coefficients from experimental data based on a physical measurement model. Measured ground truth grain sizes of the specimens from electron backscatter diffraction grain boundary images using a generalization of the ASTM E112 (ASTM 2021) intercept method. Built a curve of ultrasonic backscattering coefficients versus the ground truth intercept-based grain sizes to determine the correlation between mean grain sizes and ultrasonic measurements. Demonstrated the ability of using the correlation curve to deduce grain sizes with measured ultrasonic backscattering coefficients for a few 316L stainless steel specimens whose grain sizes were unknown beforehand but were targeted to be an extrapolation to larger grain sizes than used to formulate the correlation curves. Experimental procedures and computational algorithms are developed and validated for these tasks. This work establishes an ultrasonic technique for characterizing material microstructure with ultrafine grains that are often resulted by solid-phase processing. The technique is nondestructive, and it has the potential to be used for real time inline process monitoring. This work successfully demonstrates the viability of an ultrasonic nondestructive evaluation method for microstructural characterization of material having ultrafine grain structure (as small as 1?mm) and produced by an advanced manufacturing method. This includes a demonstration of the method to extrapolate to other conditions. While not demonstrated here, the method is expected to be viable for in-line, or near-inline, process monitoring in advanced manufacturing applications with suitable consideration for access of instrumentation to the material being manufactured.

316 L Stainless Steel↗

DOE OSTI2025

Methods for Measuring and Computing the Reference Temperature in Newton’s Law of Cooling for External Flows

Newton’s law of cooling requires a reference temperature (𝑇 𝑟𝑒𝑓 ) to define the heat-transfer coefficient (ℎ). For external flows with multiple temperatures in the freestream, obtaining 𝑇 𝑟𝑒𝑓 is a challenge. One widely used method, referred to as the adiabatic-wall (AW) method, obtains 𝑇 𝑟𝑒𝑓 by requiring the surface of the solid exposed to convective heat transfer to be adiabatic. Another widely used method, referred to as the linear-extrapolation (LE) method, obtains 𝑇 𝑟𝑒𝑓 by measuring/computing the heat flux ($𝑞^{′′}_𝑠$) on the solid surface at two different surface temperatures (𝑇 𝑠 ) and then linearly extrapolating to $𝑞^{′′}_𝑠$ = 0. A third recently developed method, referred to as the state-space (SS) method, obtains 𝑇 𝑟𝑒𝑓 by probing the temperature space between the highest and lowest in the flow to account for the effects of 𝑇 𝑠 or $𝑞^{′′}_𝑠$ on 𝑇 𝑟𝑒𝑓 . This study examines the foundation and accuracy of these methods via a test problem involving film cooling of a flat plate where $𝑞^{′′}_𝑠$ switches signs on the plate’s surface. Results obtained show that only the SS method could guarantee a unique and physically meaningful 𝑇 𝑟𝑒𝑓 where 𝑇 𝑠 =𝑇 𝑟𝑒𝑓 on a nonadiabatic surface $𝑞^{′′}_𝑠$ = 0. The AW and LE methods both assume 𝑇 𝑟𝑒𝑓 to be independent of 𝑇 𝑠 , which the SS method shows to be incorrect. Though this study also showed the adiabatic-wall temperature, 𝑇 𝐴𝑊 , to be a good approximation of 𝑇 𝑟𝑒𝑓 (<10% relative error), huge errors can occur in ℎ about the solid surface where |𝑇 𝑠 −𝑇 𝐴𝑊 | is near zero because where 𝑇 𝑠 =𝑇 𝐴𝑊 , $𝑞^{′′}_𝑠$ ≠ 0.

Newton's law of cooling↗

DOE OSTI2025

An improved method for quantitatively measuring antifouling coating performance using a mussel single thread tensile adhesion test

Surface biofouling reduces the efficiency and lifespan of equipment across many industries. The development of high-performance antifouling surfaces, such as foul release coatings, benefits from test methods that can quickly identify superior antifouling surfaces in the laboratory during material development. Existing test methods poorly discriminate between different foul release coatings. Here is presented a method to assess the ability of surfaces to resist mussel adhesion using a quantitative, controlled single thread adhesion test (STAT) method, allowing for meaningful comparisons between low adhesion foul release surfaces. This method provides greater accuracy and finer resolution than push-based mussel shear adhesion methods without the difficulties associated with mussel size, thread attachment angle, or harming the mussels. The single thread tensile method is demonstrated on a variety of standard and high-performance coatings, and it is shown that the method detects differentiation between commercial foul release coatings that could not be resolved using other methods.

42 ENGINEERING↗

DOE OSTI2024

UNDERSTANDING THE SEMI-PROBABILISTIC APPROACHES IN STRUCTURAL RELIABILITY USED TO SET DESIGN RELIABILITY TARGETS FOR GRAPHITE COMPONENTS USING ASME BPVC METHODS

Graphite is a quasi-brittle material, resulting in random variability in tensile strength distributions. To account for the random variability in strength, HHA-3000 of the ASME BPVC provides two semi-probabilistic methods for qualifying nuclear graphite components in the design stage, the simplified and full assessments. The full and simplified assessments apply statistical methods to engineering-based design problems. This is often referred to as reliability-based design. Reliability-based design (RBD) is a method to develop reliable designs by accounting for uncertainties and result in small chances of failure when also considering safety factors. RBDs provide reliability targets using semi-probabilistic approaches. RBD is implemented in ASME BPVC HHA-3000 for nuclear graphite components, but is not specific to that application. There has been much confusion around the methods implemented in ASME BPVC HHA-3000 for qualifying nuclear graphite components. To address the confusion, this paper takes a hierarchical approach. First, the general RBD framework is presented. Then, the semi-probabilistic methods and the underlying assumptions implemented in the assessments are presented. The semi-probabilistic methods are separated from the engineering modifications that have been made to the assessments. After building the framework and underlying assumptions, the specific methods in the full and simplified assessments are explained in three steps: inputs, methods, outputs. The methods are applied to an H-451 reflector block. Tensile strength properties for other graphite grades are provided.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2026

Explicit Monotone Stable Super-Time-stepping Methods for Finite Time Singularities

We explore a novel way to numerically resolve the scaling behavior of finite-time singularities in solutions of nonlinear parabolic PDEs. The Runge–Kutta–Legendre (RKL) and Runge–Kutta–Gegenbauer (RKG) super-time-stepping methods were originally developed for nonlinear complex physics problems with diffusion. These are multistage single step second-order, forward-in-time methods with no implicit solves. The advantage is that the time-step size for stability scales with stage number 𝑠 as $\mathcal{O}$⁡(𝑠 2 ). Many interesting nonlinear PDEs have finite-time singularities, and the presence of diffusion often limits one to using implicit or semi-implicit time-step methods for stability constraints. Finite-time singularities are particularly challenging due to the large range of scales that one desires to resolve, often with adaptive spatial grids and adaptive time steps. Here, in this study, we show two examples of nonlinear PDEs for which the self-similar singularity structure has time and space scales that are resolvable using the RKL and RKG methods, without forcing even smaller time steps. Compared to commonly used implicit numerical methods, we achieve a significantly smaller run time while maintaining comparable accuracy. We also prove numerical monotonicity for both the RKL and RKG methods under their linear stability conditions for the constant coefficient heat equation, in the case of infinite domain and periodic boundary condition, leading to a theoretical guarantee of the superiority of the RKL and RKG methods over traditional super-time-stepping methods, such as the Runge-Kutta-Chebyshev and the orthogonal Runge-Kutta-Chebyshev methods. Code can be found at https://github.com/ZT220501/SRK-Singularity.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2024

An iterative method to deblend AGN-Host contributions for Integral Field spectroscopic observations

ABSTRACT We present a new iterative deblending method to separate the host galaxy (HG) and their Active Galactic Nuclei (AGNs) emission with the use of Integral Field spectroscopic (IFS) data. The method decomposes the resolved HG emission from the unresolved AGN emission by modelling the two-dimensional surface brightness (SB) profile of the point-spread function (PSF) and the two-dimensional SB HG continuum simultaneously per each monochromatic slide. Our method does not require any prior information about the observed SB profile or a detailed fitting of the PSF, making it ideal for the automatic analysis of large galaxy samples. In this work, we test the quality of our method, its advantages, and its disadvantages. We test our method by using a set of IFS mock data cubes to quantify the reliability of our deblending process and further compare our method with the qdblend3d analysis tool. Furthermore, we applied our method to three data cubes selected from the MaNGA survey according to the dominance of either its HG or its AGN. We show that our deblending method is capable of disengaging the bright, non-resolved AGN emission from the HG continuum and its narrow emission lines. However, the decoupling depends on how well the IFS spatially resolves the PSF, and on the relative flux intensity of the HG-AGN. Therefore, the method is ideal for disentangling the bright-flux contribution from AGN-dominated spectra.

Ibarra-Medel, H. (ORCID:0000000297906313)↗

DOE OSTI2026

Forced Component Estimation Statistical Method Intercomparison Project (ForceSMIP)

Anthropogenic climate change is unfolding rapidly, yet its regional manifestation can be obscured by internal variability. A primary goal of climate science is to identify the externally forced climate response from among the noise of internal variability. Separating the forced response from internal variability can be addressed in climate models by using a large ensemble to average over different possible realizations of internal variability. However, with only one realization of the real world, it is a major challenge to isolate the forced response directly in observations. In the Forced Component Estimation Statistical Method Intercomparison Project (ForceSMIP), contributors used existing and newly developed statistical and machine learning methods to estimate the forced response over 1950–2022 within individual realizations of the climate system. Participants used neural networks, linear inverse models, fingerprinting methods, and low-frequency component analysis, among other approaches. These methods were trained using large ensembles from multiple climate models and then applied to observations. Here, we evaluate method performance within large ensembles and investigate the estimates of the forced response in observations. Our results show that many different types of methods are skillful for estimating the forced response in climate models, though the relative skill of individual methods varies depending on the variable and evaluation metric. Methods with comparable skill in models can give a wide range of estimates of the forced response pattern in observations, illustrating the epistemic uncertainty in forced response estimates. ForceSMIP gives new insights into the forced response in observations, its uncertainty, and methods for its estimation.

Climate attribution↗

DOE OSTI2025

A Fundamentally New Coupled Approach to Contact Mechanics via the Dirichlet‐Neumann Schwarz Alternating Method

Contact phenomena are crucial for understanding the behavior of mechanical systems. However, existing computational approaches for simulating mechanical contact often face numerical challenges, such as inaccurate physical predictions, energy conservation errors, and unwanted oscillations. Here, we introduce an alternative technique for simulating dynamic contact based on the non‐overlapping Schwarz alternating method, originally developed for domain decomposition. In multibody contact scenarios, this method treats each body as a separate, non‐overlapping domain and prevents interpenetration using an alternating Dirichlet–Neumann iterative process. This approach has a strong theoretical foundation, eliminates the need for contact constraints, and offers flexibility, making it ideal for multiscale and multiphysics applications. We conducted a numerical comparison between the Schwarz method and traditional methods, such as the Lagrange multiplier and penalty methods, focusing on a benchmark impact problem. Our results indicate that the Schwarz alternating method outperforms traditional methods in several key areas: it provides more accurate predictions for various measurable quantities and demonstrates exceptional energy conservation capabilities. To address unwanted oscillations in contact velocities and forces, we explored various algorithms and stabilization techniques, ultimately opting for the naïve‐stabilized Newmark scheme for its simplicity and effectiveness. Additionally, we validated the efficiency of the Schwarz method in a three‐dimensional impact problem, highlighting its inherent capacity to accommodate different mesh topologies, time‐integration schemes, and time steps for each interacting body.

Schwarz alternating method↗

DOE OSTI2025

A Green’s function fast multipole method for computation of micromechanical fields in heterogeneous materials

Computation of micromechanical fields in heterogeneous materials is usually performed using either the finite element method or the Green’s function method based on FFTs. The finite element method allows for accurate discretization and for non-periodic boundary conditions but is computationally expensive. On the other hand, the FFT-based method is computationally efficient but requires discretization on a regular grid of hexahedral voxels. In this paper, a Green’s function method allowing for accurate discretization using tetrahedral elements and for non-periodic boundary conditions is proposed. The convolution is computed using the fast multipole method, which provides good accuracy even for low-order expansion due to the fast decay of interactions between elements. The proposed Green’s function fast multipole method is verified by comparison with analytical and FFT-based solutions. Furthermore, the computational time is analyzed and compared to the FFT-based method for non-periodic convolution. Finally, effective properties of an elastic polycrystalline microstructure containing thin intergranular cracks are computed and analyzed.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Solving high-dimensional partial integral differential equations: The finite expression method

Partial integro-differential equations (PIDEs) have broad applications in the sciences, from electro-magnetism to options pricing. Here, in this paper, we introduce a new finite expression method (FEX) to solve PIDEs. This approach builds upon the original FEX and its inherent advantages with new advances: 1) A novel method of parameter grouping is proposed to reduce the number of coefficients in high-dimensional function approximation; 2) A Taylor series approximation method is implemented to significantly improve the computational efficiency and accuracy of the evaluation of the integral terms of PIDEs. The new FEX based method, denoted FEX-PG to indicate the addition of the parameter grouping (PG) step to the algorithm, provides both high accuracy and interpretable numerical solutions, with the outcome being an explicit equation that facilitates intuitive understanding of the underlying solution structures. These features are often absent in traditional methods, such as finite element methods (FEM) and finite difference methods, as well as in deep learning-based approaches. To benchmark our method against recent advances, we apply the new FEX-PG to solve benchmark PIDEs in the literature. In high-dimensional settings, FEX-PG exhibits strong and robust performance, achieving relative errors on the order of single precision machine epsilon, significantly outperforming existing approaches based on neural networks.

Combinatorial optimization↗

DOE OSTI2026

Physicochemical and Performance Characterization of Six Commercial Organic Solvent Nanofiltration Membranes

This work introduces a novel, gradient-free metamaterial design method based on Gaussian process regression to represent the density field of a unit cell. The dimension of the design space is determined by the covariance matrix dimension in the Gaussian process regression. We propose compressing this matrix using an autoencoder, enabling the decoder to generate the density field and effectively reduce the originally large design space to a lower-dimensional subspace. In this compressed space, we employ an active learning method, Bayesian Adaptive Direct Search (BADS), for efficient exploration of the design space. We demonstrate that for simple 2D designs aimed at maximizing unit cell stiffness, our method yields results comparable to those of standard topology optimization. Furthermore, we extend our approach to various mechanical problems, from linear elasticity to hyperelastic large deformation and elasto-plasticity under finite deformation, to 3D metamaterial design. This illustrates the method’s versatility and effectiveness across a range of applications.

Wu, Haoran↗

DOE OSTI2025

Clumping index estimation with 30°-tilted cameras in row crops: Evaluation of methods and segment size effects

The clumping index (CI) quantifies the spatial distribution of foliage elements and is essential for accurately estimating the plant area index (PAI), canopy radiative transfer, and photosynthesis. Traditionally, the finite-length averaging method (LX), the gap size distribution method (CC), and a combined approach of CC and LX (CLX) have been applied to instruments like TRAC and digital hemispherical photography to estimate CI. However, a comprehensive evaluation of these methods in row crops remains limited, especially regarding the influence of segment size on CI. Meanwhile, digital cameras offer a cost-effective and user-friendly solution for canopy measurements in row crops, yet their application in this context remains underexplored. In this study, we employed a new approach using a 30°-tilted digital camera to estimate CI in corn and soybean fields, applying the LX, CC, and CLX methods. We systematically assessed the performance of these three methods by combining field measurements in real-world fields with simulations using the LESS 3D radiative transfer model. Our results showed that CLX applied to the whole image and 45° segment offered accurate estimation of CI (bias within ±0.1, RMSE < 0.2) and PAI (bias within ±0.4, RMSE < 1) in real-world fields and LESS simulations. The accuracy of the LX method was highly sensitive to segment size, with the best performance observed at the 15° segment (PAI bias within ±0.4). In contrast, the CC method remained stable across different segment sizes, and its performance was generally comparable to that of LX, except at the 15° segment. Across view zenith angles, CI derived from CC generally showed a continuous increase, while those from LX and CLX followed a rising trend at small zenith angles but began to decline at 68°, likely due to an increasing proportion of no-gap segments. Seasonally, LX tended to show decreasing CI during early growth stages but increased as the canopy matured, whereas CC and CLX showed gradually increasing CI before plateauing at peak PAI. The 30°-tilted camera effectively captured CI variations across different angles and growth stages, making it a practical and robust instrument for row crop canopy structure analysis. Furthermore, applying these CI methods to digital cameras offers a low-cost and accessible CI estimation alternative, improving canopy structure monitoring accuracy in row crops.

30°-tilted camera↗

DOE OSTI2025

Advanced Method Optimization with Categorical and Constrained Continuous Parameters

Traditional approaches to analytical method optimization (e.g., univariate and “guess-and-check”) can be time-consuming, costly, and often fail to identify true optima within the parameter space. Previous work defined and implemented a generalized technique for method optimization for continuous method parameters, but a knowledge gap remains for the incorporation of categorical variables into these advanced method optimization schemes. This work presents and validates a generalized optimization approach that incorporates both continuous and categorical variables while also utilizing a multivariate, multiobjective optimization scheme with Karush–Kuhn–Tucker conditions to bound the optimization space to solutions within the physical limitations of the parameter space. Method optimization from a case study using GC–MS for the analysis of 11 analytical standards with objectives to minimize peak width and maximize peak height resulted in a 3 orders of magnitude improvement in the average peak height and a 2 orders of magnitude improvement in the average peak width compared to the least optimal (but reasonable) instrumental parameters utilized in this study. This approach to optimization allows for a customizable method optimization in which users can include both continuous and categorical variables to achieve objectives specific to their analytical goals. This approach significantly reduces the labor and cost associated with traditional method development approaches and can be applied in a variety of scientific fields across a range of laboratory techniques (e.g., instrument method development, sample preparation, and extraction techniques).

Amorphous materials↗

DOE OSTI2024

A New Galerkin Quadrature Method Not Requiring a Matrix Inverse

We derive a new Galerkin quadrature (GQ) method for S 𝑛 calculations that differs from the two methods preceding it in that a matrix inverse for an 𝑁 𝑑 × 𝑁 𝑑 matrix, where 𝑁𝑑 is the number of directions in the quadrature set, is no longer required. Galerkin quadrature methods are designed for calculations with highly anisotropic scattering. Such methods are not simply special angular quadratures but also are methods for representing the S 𝑛 scattering source that offers several advantages relative to the standard scattering source representation when highly truncated Legendre cross-section expansions must be used. Galerkin quadrature methods are also useful when the scattering is moderately anisotropic, but the quadrature being used is not sufficiently accurate for the order of the scattering source expansion that is required. Furthermore, we derive the new method and present computational results showing that its performance for two challenging problems is comparable to those of the two GQ methods that preceded it.

Galerkin quadrature↗

DOE OSTI2026

Validating and Comparing Energy Estimation Methods at Water Resource Recovery Facilities

Water resource recovery facilities play a crucial role in the water-energy nexus, consuming a substantial amount of energy in the United States. Growing treatment volumes and more stringent water quality standards are expected to increase the amount of energy needed to treat wastewater, but accurately estimating energy consumption and potential remains challenging due to variability in scale, treatment methods, and effluent treatment standards. In this study, we used publicly available data to evaluate the accuracy of methods for estimating energy consumption and generation, then quantified uncertainty based on key factors like flow rate, treatment level, and geographic location. To validate methods, we estimated energy consumption and generation at the facility-level, then compared estimates to self-reported data from utilities in major U.S. cities. We found that process models of treatment trains under best practice configurations were accurate relative to other methods for estimating electricity use, total energy use, and electricity generation from biogas utilization, and less complex methods based on effluent treatment level and prime movers also performed well for estimating electricity consumption and generation, respectively. Applying the evaluated methods to a national inventory of treatment facilities, we estimate that annual energy consumption ranged from 56.3 x 10^3 to 82.5 x 10^3 TJ in 2012 and 83.6 x 10^3 to 127 x 10^3 TJ in 2042. Our results indicate that not all estimation methods are suited for every use case, so we recommend that researchers and practitioners select an estimation method based on data availability and desired computational intensity.

Hodson, Abigayle↗

DOE OSTI2025

A Comparison of Machine Learning Methods of Association Tested on Dense Nodal Arrays

The association of phase picks to form events is one of the fundamental components of seismology. Large and dense sensor networks, such as >1000 geophone arrays (and distributed acoustic sensing), offer unique challenges in association due to the vast numbers of observations and high likelihood of errant picks. In addition, the large number of stations can greatly increase the time it takes to perform the association. For this reason, machine learning (ML) methods might provide a more optimal method of association for such networks. In this work, we examine how well ML methods (e.g., Gaussian mixture model association, PhaseLink, and Graph Earthquake Neural Interpretation Engine) can incorporate dense seismic arrays into regional networks and how well they handle the increasing numbers of stations. Here, we test their capabilities on two dense seismic deployments, one within Rock Valley Nevada (52 nodes and a 9-station sparse local network), and the LArge-n Seismic Survey in Oklahoma dense nodal array (>1800 vertical-component geophones). Processing data from these two different styles of dense seismic deployments allows testing of how the ML algorithms can merge array data with a broader regional network, how they deal with poorly picked phases, and how they handle anthropogenic noise. We compare the ML-associated bulletins to those obtained using the Rapid Earthquake Association and Location algorithm, a more traditional method of association. We find that there are very small differences in results between the methods for small networks (<100 stations) with low pick rates. For large networks (>1000), there are enough errant picks that some of the ML methods start to create false events out of noise. We also find that the ML methods vary in computation time significantly but are all faster than the traditional method tested here.

58 GEOSCIENCES↗

DOE OSTI2025

Chelation ion chromatography as an automated, and cost-effective analytical technique for REE determination: method development and applications

Rare earth elements (REEs), as critical minerals, have important uses in modern energy and technologies, yet are vulnerable to potential supply chain disruptions. To establish domestic REE supply chain, efficient REE detection methods for resource characterization and mineral processing will be needed to accelerate innovations for domestic REE recovery. This study developed a rapid, novel, and cost-effective for REE detection method using ion chromatography (IC) for aqueous samples. Various REE-targeted eluent gradients and post-column agent compositions were tested on the chelation ion chromatography (CIC) with UV-vis detector for optimal separation and quantification of REEs within approximately 20 min. The single-channel pump to deliver the post-column solution to UV-vis detector was replaced with a 4-channel gradient pump, to increase operation and maintenance efficiencies. After method optimization, resulting calibration curves for more than ten REEs achieved high coefficients of determination (R2>0.999) and low relatively standard deviations (below 3.24%), demonstrating sub-ppm level detection limits (0.0897 to 0.1149 mg/L). The reliability of the CIC method was validated through comparison with inductively coupled plasma mass spectrometry (ICP-MS), showing strong agreement in REE recovery from certified standards. The impact of metal ions and salts on REE recovery using CIC was also systematically investigated. CIC consistently exhibited reliable performance in the presence of salt solutions such as NaCl and Na₂SO₄ (up to 10,000 mg/L). Our study also found the presence of high concentrations of Al ions (at 10,000 mg/L) significantly influenced REE determination, and elevated concentrations of Ca ions affected the recovery of specific REEs, including La, Ce, and Pr. The CIC method was further tested on REE-containing eluents from solvent extraction tests out of fly ash leachates. REE detection from these real processing fluids were reported to achieve 90% to 100% recovery rate from our IC method, compared to ICP-MS results. This study underscores the potential of CIC as a reliable and efficient alternative for REE determination in complex matrices. It also highlights the importance of minimizing select interfering metal ions in solutions to ensure accurate results. The REE CIC method presents a promising, low-maintenance, salt-tolerant, and cost-effective alternative to traditional analytical methods for REE analysis.

detection of rare earth elements (REE)↗