Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “mechanical reinforcement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

The first experimental evidence for improved nanomechanical properties of calcium silicate hydrate by polycarboxylate ether and graphene oxide

Graphene oxide (GO) efficiently enhances macroscale mechanical properties of cement-based materials. Yet the nanoscale reinforcing mechanism of GO for calcium silicate hydrate (C-S-H), the key binding phase of concrete, remains poorly understood. Moreover, how polycarboxylate ether (PCE)-based superplasticizers affect the nanomechanical properties of C-S-H remains unclear. The intrinsic mechanical properties of the nanocomposites are measured using high-pressure X-ray diffraction. The influences of GO and PCE on the local Ca and Si environments are probed using X-ray absorption spectroscopy. For the first time, we evidence that PCE-induced well-dispersed GO nanoplatelets strengthen the C-S-H basal planes, whereas poorly water-dispersed GO weakly interacts with basal planes and does not strengthen in plane Casingle bondO bonds. Both PCE and GO only slightly strengthen C-S-H's c-axis. Here, the bulk modulus of C-S-H/PCE/GO nanocomposite is 190% than pure C-S-H. Functional groups of PCE and GO prefer interacting with the Casingle bondO sheets of C-S-Hs instead of silicate tetrahedra.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Preparation, mechanical properties, and toughening mechanisms of SiCw/SiCp‐reinforced zirconia‐toughened alumina ceramics

ABSTRACT Zirconia‐toughened alumina (ZTA) ceramics with high mechanical properties were sintered by hot‐pressing method using SiC particles (SiCp) and SiC whiskers (SiCw) as the reinforcing agents simultaneously. The influences of sintering temperature, SiCp, and SiCw contents on the microstructure and mechanical properties of ZTA ceramics were investigated. It was found that both SiCp and SiCw could contribute to grain refinement significantly and promote the mechanical properties of the ceramics. However, the excess addition of SiCp or SiCw led to the formation of pores with large sizes and degraded the mechanical properties instead. When 13 wt% SiCp was introduced, the maximum flexural strength of 1180.0 MPa and fracture toughness of 15.9 MPa·m 1/2 were obtained, whereas the maximum flexural strength of 1314.0 MPa and fracture toughness of 14.7 MPa·m 1/2 were achieved at 20 wt% SiCw. Interestingly, the simultaneous addition of SiCp and SiCw could further improve the mechanical properties, and the highest flexural strength of 1334.0 MPa and fracture toughness of 16.0 MPa·m 1/2 were achieved at a SiCw/SiCp ratio of 16/4. The reinforcement mechanisms in the ceramics mainly included the phase transformation toughening of ZrO 2 , the crack deflection and bridging of SiCp and SiCw, and the pull‐out of SiCw.

Liu, Longyang↗
DOE OSTI2025

Strong, ductile, and hierarchical hetero-lamellar-structured alloys through microstructural inheritance and refinement

The strength−ductility trade-off exists ubiquitously, especially in brittle intermetallic-containing multiple principal element alloys (MPEAs), where the intermetallic phases often induce premature failure leading to severe ductility reduction. Hierarchical heterogeneities represent a promising microstructural solution to achieve simultaneous strength−ductility enhancement. However, it remains fundamentally challenging to tailor hierarchical heterostructures using conventional methods, which often rely on costly and time-consuming processing. Here, we report a multiscale microstructural inheritance and refinement strategy to process “structural hierarchy precursors” in as-cast heterogeneous Al 0.7 CoCrFeNi MPEAs, which lead directly to a hierarchical hetero-lamellar structure (HLS) after simple rolling and annealing. Interestingly, it takes only 10 min of annealing time, two orders of magnitude less than that required to render the state-of-the-art properties during conventional processing of Al 0.7 CoCrFeNi, for us to achieve record-high strength−ductility combinations via the hierarchical HLS design that sequentially stimulates multiple unusual deformation and reinforcement mechanisms. In particular, the HLS-enabled high hetero-deformation-induced (HDI) internal stress triggers profuse <111>-type dislocations on over five independent slip systems in the supposedly brittle intermetallic phase and activates extensive stacking faults (SFs) and nanotwinning in the adjoining soft phase with a rather high SF energy. These unexpected, dynamically reinforcing hetero-deformation mechanisms across multiple length scales facilitate high sustained HDI strain hardening, along with a salient microcrack-mediated extrinsic ductilization effect, suggesting that the proposed microstructural inheritance and refinement strategy provides an efficient, fast, and low-cost approach to overcome the strength−ductility trade-off in a broad range of structural materials.

Science & Technology - Other Topics↗
DOE OSTI2020

Phosphonium-Based Polyzwitterions: Influence of Ionic Structure and Association on Mechanical Properties

This manuscript describes a synthetic strategy and structure–property investigation of unprecedented phosphonium-based zwitterionic homopolymers (polyzwitterions) and random copolymers (zwitterionomers). Free radical polymerization of 4-(diphenylphosphino)styrene (DPPS) provided neutral polymers containing reactive triarylphosphines. Quantitative postpolymerization alkylation of these pendant functionalities generated a library of polymers containing various concentrations of neutral phosphines, phosphonium ions, and phosphonium sulfobetaine zwitterions. The zwitterionic homo- and copolymers exhibited significantly higher glass transition temperatures (T g ) and enhanced mechanical reinforcement in comparison to neutral and phosphonium analogues. These changes in T g and mechanical properties were attributed to nanoscale morphological domains, which formed due to electrostatic interactions between zwitterionic groups, as revealed by X-ray scattering and broadband dielectric spectroscopy (BDS). BDS revealed increased static dielectric constants (>25) for the phosphonium zwitterionomers compared to ionomeric or neutral analogues. These high static dielectric constants for the solvent-free polyzwitterions supported their stronger polarization response in comparison with polymers containing neutral phosphines and phosphonium ions, and these interactions accounted for morphological differences and enhanced mechanical behavior. This work describes a versatile strategy for modulating electrostatic interactions with tunable mechanical properties for an unprecedented family of zwitterionic polymers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Origin of Heating-Induced Softening and Enthalpic Reinforcement in Elastomeric Nanocomposites

Molecular simulations demonstrate that the enthalpic softening of elastomeric nanocomposites upon heating can arise naturally from a Poisson’s ratio mismatch between elastomer and nanoparticle networks, providing a more parsimonious explanation for this phenomenon than the widely accepted interpretation based on glassy interparticle bridging. Despite a century of use, the mechanism of nanoparticle-driven mechanical reinforcement of elastomers is unresolved. Here, a major hypothesis attributes it to glassy interparticle bridges, supported by an observed inversion of the variation of the modulus E(T) on heating – from entropic stiffening in elastomers to enthalpic softening in nanocomposites. Here, molecular simulations reveal that elastomer enthalpic softening can instead emerge from a competition over the preferred volumes between elastomer and nanoparticulate networks. A theory for this competition accounting for softening of the bulk modulus on heating predicts the simulated E(T) inversion, suggesting that reinforcement is driven by a volume-competition mechanism unique to cocontinuous systems of soft and rigid networks.

Biopolymers↗
DOE OSTI2022

Aqueous-Based Polyimine Functionalization of Cellulose Nanofibrils for Effective Drying and Polymer Composite Reinforcement

Here a simple strategy was developed to synthesize polyimine-coated cellulose nanofibrils (CNF) for effective CNF drying and composite reinforcement. The polyimine was synthesized in an aqueous medium using a selective hydrophilic and hydrophobic component that forces the polyimine to precipitate, which prevents the reverse imine reaction. The polyimine coating allowed the CNF to be easily oven-dried while maintaining a fibrillar morphology to provide mechanical reinforcement in poly(ethylene terephthalate glycol) (PETG) composites. In comparison, poor mechanical performance and a heterogeneous fracture surface were observed when the coated CNF were incorporated into poly(l-lactide) (PLA) composites. It is hypothesized that intermolecular aromatic–aromatic interactions are formed at the interface between fibers and the polymer matrix in the PETG system, while no such phenomena occur in the PLA system. Overall, this facile strategy to produce modified, easily dried CNF can be adapted to produce polyimine-coated CNF with unique functionalities that are useful in a range of applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Carbon Fiber Reinforced Epoxy Vitrimer: Robust Mechanical Performance and Facile Hydrothermal Decomposition in Pure Water

Conventional carbon fiber reinforced thermosetting polymers (CFRPs) are neither recyclable nor repairable due to their crosslinked network. The rapid growing CFRP market raises a serious concern of the waste management. In this work, a viable method to develop a readily recyclable CFRP based on epoxy vitrimer is introduced. First, a self-catalytic epoxy prepolymer with built-in hydroxy and tertiary amine groups is designed, which upon reaction with an anhydride formed a catalyst-free epoxy vitrimer. The epoxy prepolymer is synthesized from a diamine and an excess of bisphenol A epoxy resin. The hydroxyls and tertiary amines of the epoxy prepolymer efficiently catalyze both curing and the dynamic transesterification of the crosslinked polymer without the need of a catalyst. Then, the epoxy vitrimer is used as the matrix resin to prepare CFRP. The resulting CFRP exhibited a tensile strength as high as 356 MPa. More interestingly, the matrix of the CFRP is efficiently degraded in pure water at above 160 °C. This is because the built-in tertiary amines catalyze the hydrolysis of the ester bonds of the crosslinked network. The simple method developed in this work provides a framework for the development of recyclable CFRP.

Liu, Tuan↗
DOE OSTI2021

Collective Nanoparticle Dynamics Associated with Bridging Network Formation in Model Polymer Nanocomposites

The addition of nanoparticles (NPs) to polymers is a powerful method to improve the mechanical and other properties of macromolecular materials. Such hybrid polymer–particle systems are also rich in fundamental soft matter physics. Among several factors contributing to mechanical reinforcement, a polymer-mediated NP network is considered to be the most important in polymer nanocomposites (PNCs). Here, we present an integrated experimental–theoretical study of the collective NP dynamics in model PNCs using X-ray photon correlation spectroscopy and microscopic statistical mechanics theory. Silica NPs dispersed in unentangled or entangled poly(2-vinylpyridine) matrices over a range of NP loadings are used. Static collective structure factors of the NP subsystems at temperatures above the bulk glass transition temperature reveal the formation of a network-like microstructure via polymer-mediated bridges at high NP loadings above the percolation threshold. The NP collective relaxation times are up to 3 orders of magnitude longer than the self-diffusion limit of isolated NPs and display a rich dependence with observation wavevector and NP loading. A mode-coupling theory dynamical analysis that incorporates the static polymer-mediated bridging structure and collective motions of NPs is performed. It captures well both the observed scattering wavevector and NP loading dependences of the collective NP dynamics in the unentangled polymer matrix, with modest quantitative deviations emerging for the entangled PNC samples. Here, we identify an unusual and weak temperature dependence of collective NP dynamics, in qualitative contrast with the mechanical response. Hence, the present study has revealed key aspects of the collective motions of NPs connected by polymer bridges in contact with a viscous adsorbing polymer medium and identifies some outstanding remaining challenges for the theoretical understanding of these complex soft materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Mechanical Properties of Polyisoprene-Based Elastomer Composites

Herein we have explored the origins of mechanical reinforcement in elastomers filled with polymer-grafted nanoparticles (NPs). The brush chains are constructed from the same monomers as the polymer melt, although they have different microstructures (i.e., different amounts of trans and cis isomers). The NPs display a variety of morphologies depending on variations in the graft density of the polymers, with these morphologies hardly changing when the matrix (and the grafts) is cross-linked using dicumyl peroxide (DCP). NMR measurements show that the cross-link densities depend only on the DCP content and are independent of NP morphologies. We find that the elastic moduli of these materials are strongly dependent on the NP morphology but that the maximum reinforcement occurs when the NPs percolate, in a manner where the cores are exposed enough to have strong enthalpic interactions; these interactions could either be due to direct core–core van der Waals attractions or due to bridging interactions driven by polymers adsorbed on adjacent NPs. The nonlinear mechanical response of these materials is less sensitive to changes in NP morphology and loading. These results emphasize the important role of the exposed NP surface in determining the moduli of cross-linked elastomers. This last aspect is apparently less relevant for the corresponding uncross-linked melts filled with NPs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Challenges in Continuous In-Field Critical Current Testing of High-Temperature Superconducting Tapes: Thermal and Mechanical Perspectives

High-temperature superconductors (HTS) are essential for ultra-high-field applications requiring exceptional current-carrying capacity under extreme conditions. However, systematic characterization of critical current in long-length conductors remains challenging due to complex thermal, electromag netic, and mechanical interactions during continuous testing. This study reports the development of a continuous in-field magnetization testing system for position-dependent critical current measurement in HTS tapes at 20 K under 7.5 T fields applied normal to the tape plane, enabling identification of performance-limiting regions that could compromise magnet stability. Here, the system addresses two fundamental challenges inherent to cryogenic reel to-reel testing. First, thermal management requires continuous cooling of a moving conductor to 20 K, achieved through liquid nitrogen precooling combined with a 100 W@20 K Gifford McMahon cryocooler. Second, screening currents in high fields generate Lorentz forces that induce twisting, bowing, and potential delamination. To mitigate these risks, we propose mechanical reinforcement and active current density suppression strategies. Numerical simulations using the stream function formulation reveal four primary failure modes: frictional heating at guide interfaces, unstable equilibria causing deformation, transverse current-induced stresses at guide transitions, and unsupported forces in vertical spans. Our mitigation strategies include PTFE coated guides to minimize friction, spring-loaded stabilization mechanisms to maintain tape alignment, controlled pre-heating using the liquid nitrogen thermal jacket to suppress critical current at stress points, and optimized guide positioning to minimize force accumulation. The experimental system is nearing completion, with testing planned to commence within two months. Preliminary validation at 65 K under 0.5 T demonstrates strong correlation between simulation-predicted mechanical instabilities and observed critical current variations during conductor tran sitions through the measurement region. These findings establish a robust foundation for quality assurance protocols essential to next-generation superconducting magnet applications.

Chen, Siwei [Princeton Plasma Physics Laboratory (↗
DOE OSTI2025

Intermediate States Enable Keratin-like α-To-β Transformations in Strain-Responsive Synthetic Polypeptides

Nature’s fibrous proteins, such as α-keratin, achieve remarkable mechanical properties by undergoing strain-induced α-to-β conformational transitions. Inspired by these materials, we report a strategy for designing synthetic polypeptides that undergo similar transformations at elevated temperatures far exceeding keratin’s operational range. By employing helix-confined ring-opening polymerization (ROP) of N -carboxyanhydrides (NCAs) initiated by a short poly(γ-benzyl- L -glutamate) (PBLG) precursor, we synthesized poly( O -benzyl- L -serine) (PBLS) chains that adopt an α-helical structure yet transition into β-sheets upon heating. Compression molding at carefully chosen temperatures drives PBLS segments into an α-β intermediate state, characterized by relaxed intrachain hydrogen bonds and a hexagonal packing arrangement. Under mechanical strain, these intermediate states convert in situ into β-sheets, producing significant strain-hardening well below the spontaneous α-to-β temperature threshold. Further, this approach extends to polypeptides bearing different side chains, such as poly(S-benzyl- L -cysteine), demonstrating robust mechanical reinforcement across a wide temperature window up to ∼ 200 °C. In situ synchrotron X-ray analysis confirms that chain alignment, β-sheet formation, and domain growth occur stepwise during deformation. By harnessing the intermediate states and the supramolecular cooperativity conferred by compression-molded films, our method provides a versatile platform for developing next-generation polypeptide materials with tunable mechanical resilience and responsiveness─surpassing the temperature limitations of natural fibrous proteins and enabling potential applications demanding broad-temperature mechanical adaptability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Tailorable thermoplastic insulation foam composites enabled by porous-shell hollow glass spheres and expandable thermoplastic microspheres

Here we report a simple and commercially viable strategy to produce thermoplastic composite foams using synergistic foaming approaches – incorporating porous-shell hollow-interior glass spheres (PHGS) as a filler and utilizing expandable thermoplastic microspheres (EMS) as a physical blowing agent – for thermal insulation applications. The EMS in these composites ensure formation of highly porous, low-density foam while the PHGSs provide low thermal conductivity and lightweight mechanical reinforcement. Through systematic optimization of the PHGS and EMS loadings, a lightweight, and robust insulation with thermal resistivity greater than 27.7 m·K/W (R/in. > 4) is achieved. Notably, the fabricated foams also demonstrated comparable compressive strength than some commercial thermoplastic insulating materials. Through optimization of PHGS and EMS concentrations, results indicated similar thermal performance characteristics at varying foam densities, while higher loadings of both components lead to reduced insulation performance and weak mechanical stability of the foams. The results obtained, when coupled with the potential scalability and tailor ability of the overall process towards targeted insulation performance, not only endows competitiveness with current commercial thermoplastic insulating materials but also offers great promise for the development of unique thermoplastic composite foams for a variety of insulation systems.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Multifunctional Nanofiber Reinforcement for Improved Thermomechanical and Chemical Stability of Perovskite Solar Cells

This project focused on the development of metal halide perovskite-polymeric nanofiber nanocomposites for robust and efficient solar cells. Metal halide perovskite solar cells are a potentially disruptive technology with high efficiencies and low-cost solution processability amenable with roll-to-roll fabrication of flexible devices. However, perovskites exhibit extreme brittleness, high internal film stresses, and chemical instabilities that significantly limit service lifetimes under normal operating conditions. To date, most work addressing these shortcomings has been focused on encapsulating devices between thick layers of rigid materials such as glass, which increases the total weight and cost of devices. Furthermore, these rigid and heavy encapsulants do not translate well to emerging solar markets vital for national security, including integrated mobile power, emergency deployments for disaster relief and military engagement, and lightweight power for space. It is therefore critical to improve the thermomechanical and chemical stability of perovskite devices in a way that is compatible with flexible and lightweight substrates. In this project, we integrated nylon-6,6 nanofibers into MAPbI3 to mechanically reinforce the perovskite, demonstrating films that exhibited fracture energies 5-fold greater than pristine MAPbI3 while also maintaining similar power conversion efficiencies due to beneficial light scattering effects from the polymeric nanofibers. These results required successful development of approaches to control the deposition thickness of nanofiber mats down to 100s of nanometers, and to ensure the polymer nanofibers did not inhibit charge transport to the at the perovskite-transport layer interface.

14 SOLAR ENERGY↗
DOE OSTI2021

Sodium dodecyl sulfate modulates the structure and rheological properties of Pluronic F108–poly(acrylic acid) coacervates)

Micelles formed within coacervate phases can impart functional properties, but it is unclear if this micellization provides mechanical reinforcement of the coacervate whereby the micelles act as high functionality crosslinkers. Here, we examine how sodium dodecyl sulfate (SDS) influences the structure and properties of Pluronic F108–polyacrylic acid (PAA) coacervates as SDS is known to decrease the aggregation number of Pluronic micelles. Increasing the SDS concentration leads to larger water content in the coacervate and an increase in the relative concentration of PAA to the other solids. Rheological characterization with small angle oscillatory shear (SAOS) demonstrates that these coacervates are viscoelastic liquids with the moduli decreasing with the addition of the SDS. The loss factor (tan δ) initially increases linearly with the addition of SDS, but a step function increase in the loss factor occurs near the reported CMC of SDS. However, this change in rheological properties does not appear to be correlated with any large scale structural differences in the coacervate as determined by small angle X-ray scattering (SAXS) with no signature of Pluronic micelles in the coacervate when SDS concentration is >4 mM during formation of the coacervate, which is less than that observed (6 mM SDS) in initial Pluronic F108 solution despite the higher polymer concentration in the coacervate. Finally, these results suggest that the mechanical properties of polyelectrolyte-non-ionic surfactant coacervates are driven by the efficicacy of binding between the complexing species driving the coacervate, which can be disrupted by competitive binding of the SDS to the Pluronic.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Binder Effects on Processing, Mechanical Properties, and Performance of Thin Sulfide Solid‐State Electrolytes

All‐solid‐state batteries (ASSBs) offer enhanced safety and energy density compared to conventional lithium‐ion batteries by replacing flammable liquid electrolytes with solid‐state electrolytes (SSEs). Among SSEs, sulfide‐based electrolytes exhibit high ionic conductivity and mechanical deformability, making them promising candidates for next‐generation energy storage. However, their practical implementation is hindered by interfacial instability, mechanical brittleness, and challenges in fabricating ultrathin electrolyte membranes (<30 μm) with robust mechanical integrity. Here, this study systematically examines the influence of polymeric binders—polyisobutylene, hydrogenated nitrile butadiene rubber, and styrene–ethylene–butylene–styrene (SEBS)—on the structural, mechanical, and electrochemical performance of thin sulfide SSE membranes. Key findings reveal that SEBS enables the fabrication of ultrathin, uniform membranes, while binder elasticity significantly affects structural stability during cycling. Operando stack pressure measurements indicate that binder properties directly influence adhesion force for LPSCl particles, influencing their stabilizing cycling period. These results underscore the critical role of polymer binders beyond mechanical reinforcement, positioning them as essential design variables in sulfide SSE engineering. By linking binder chemistry to processability and electrochemical performance, this study provides insights into optimizing sulfide SSEs, advancing their commercial viability in ASSBs.

argyrodite sulfide electrolyte↗
DOE OSTI2021

Tungsten disulfide nanotubes enhance flow-induced crystallization and radio-opacity of polylactide without adversely affecting in vitro toxicity

Treatment of vascular disease, from peripheral ischemia to coronary heart disease (CHD), is poised for transformation with the introduction of transient implants designed to “scaffold” regeneration of blood vessels and ultimately leave nothing behind. Improved materials could expand the use of these devices. Here, we examine one of the leading polymers for bioresorbable scaffolds (BRS), polylactide (PLA), as the matrix of nanocomposites with tungsten disulfide (WS 2 ) nanotubes (WSNT), which may provide mechanical reinforcement and enhance radio-opacity. We evaluate in vitro cytotoxicity using vascular cells, flow-induced crystallization and radio-opacity of PLA-WSNT nanocomposites at low WSNT concentration. A small amount of WSNT (0.1 wt%) can effectively promote oriented crystallization of PLA without compromising molecular weight. And radio-opacity improves significantly: as little as 0.5 to 1 wt% WSNT doubles the radio-opacity of PLA-WSNT relative to PLA at 17 keV. The results suggest that a single component, WSNT, has the potential to increase the strength of BRS to enable thinner devices and increase radio-opacity to improve intraoperative visualization. Here, the in vitro toxicity results indicate that PLA-WSNT nanocomposites are worthy of investigation in vivo. Although substantial further preclinical studies are needed, PLA-WSNT nanocomposites may provide a complement of material properties that may improve BRS and expand the range of lesions that can be treated using transient implants.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Next-generation anion exchange membrane water electrolyzers operating for commercially relevant lifetimes

Alkaline anion exchange membrane (AEM) water electrolysis has gained increasing attention due to its potential to achieve low-cost, high performance hydrogen production. However, most existing membranes are not durable in industrial settings. In this work, we demonstrate good performance relative to industrial parameters using Sustainion® anion exchange membranes. Long-duration tests showed stable performance of 1 A/cm 2 at 1.85 V with a degradation rate of less than 1 μV/h over 10,000 h. The projected lifetime is thus over 20 years. Daily on/off cycling performance over the course of 30 years was simulated experimentally through accelerated voltage shock tests, resulting in a performance loss of only 0.15 μV/cycle over 11,000 cycles. As shown through impact and crossover testing, an improvement in performance is achieved by the addition of zirconia to the polymer matrix and mechanically reinforcing the membrane.

08 HYDROGEN↗
DOE OSTI2021

Nonlinear Architectures Can Alter the Dynamics of Polymer–Nanoparticle Composites

Polymer nanocomposites exhibit remarkable physical properties that are attractive for many applications. These systems have been so far investigated by using linear polymer chains; the role of polymer matrix architecture on local dynamics, bulk rheology and nanoparticle motion remains unexplored. Here, using quasielastic neutron scattering, bulk rheology and x-ray photon correlation spectroscopy, we investigated nanocomposites with spherical silica nanoparticles well dispersed in poly (ethylene oxide) matrices having different architectures (specifically linear, stars and hyperbranched). The results reveal that the mechanical reinforcement of the nanocomposites with the nonlinear polymers can be altered by orders of magnitude with respect to the conventional nanocomposite with the linear polymer. Additionally, the polymer compactness and inter-penetrability are found to play crucial roles in determining their bulk rheology. At microscopic level, average segmental dynamics is remarkably slowed down by the attractive NPs in the matrices of high degree of branching whereas no significant effect is observed in linear polymer matrix at the same NP loading. In addition, the nanoscale dynamics of particles in the compact nonlinear matrices exhibit strong decoupling from the bulk viscoelasticity, allowing their fast relaxation even at ≈ 30% by volume. These results provide an experimental evidence that macromolecular architecture is a powerful new tool for tuning the bulk rheological properties as well as the nanoscale dynamics of PNCs without the need for changing polymer molecular weight, nanoparticle size, shape, loading or dispersion state.

36 MATERIALS SCIENCE↗