Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “measurement bandwidth”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

A fixed tuned broadband matching structure for submillimeter SIS receivers

The authors have designed, fabricated, and tested a quasi-optical submillimeter wave receiver with an Nb/AlO(x)/Nb tunnel junction. This design incorporates a hybrid antenna fed by a planar logarithmic spiral structure in order to couple to the radiation field from the telescope. The novel matching circuit requires several layers of photolithographic processing on top of the actual tunneling device. Computer modeling of the device correctly predicted the measured bandwidth and the characteristic frequencies to within 8 percent. A good match has been obtained from 200 to 475 GHz between the antenna and a relatively large area (1 sq mm) tunnel junction with omega(R(n))C about 2-4. Noise measurements at 318 GHz, 395 GHz, 426 GHz, and 492 GHz yielded uncorrected double sideband receiver noise temperatures of 200 K, 230 K, 220 K, and 500 K, respectively. Using the same optics, coupling efficiencies between the receiver and the Caltech Submillimeter Telescope were found to have values approaching those achieved by the best waveguide-horn-based receiver systems.

Buttgenbach, Thomas H.↗
NASA NTRS1997

Microwave Transmission Technique for Accurate Impedance Characterization of Superconductive Bolometric Mixers

The impedance of the supconducting hot-electron bolometer mixer was measured in the range 0.2-4 GHz. A special technique relying on determination of S21 transmission parameter of the device was used. Many advantages of the techinque (wide frequency range, in sity calibration, low tes power, accuracy) are demonstrated. The estimate of the mixer bandwidth from the impedance data using the mixer theory is in good agreement with the results ofthe direct bandwidth measurements.

hot-electron bolometer mixer transmission↗
NASA NTRSDate not supplied

Practical Considerations using Weighted-Acceleration Compensation Techniques for Dynamic Force Measurements in Wind Tunnels

Most wind tunnel force measurement systems are designed and calibrated for high-accuracy static measurements, but may have limited ability to sense dynamic forces and moments. As a means to improve the measurement bandwidth of dynamic forces, researchers have proposed using a weighted-acceleration technique, which uses accelerometer data to compensate and correct for system dynamics. The sum of weighted-accelerations method is attractive as the acceleration data applies a correction to the traditional static measurements. The focus of this paper is on practical aspects of implementing a weighted-acceleration technique in an experimental arrangement. A formulation of the weighted-acceleration methodology is validated on a reduced-order model and demonstrated on a tabletop experiment that serves as a proxy to a wind tunnel force measurement system. As part of this system, a two component normal force and pitching moment balance was designed and fabricated. A static and dynamic calibration of the system was performed, and the weighted-acceleration technique was used to reconstruct impact forces acting on the system. Practical considerations of the experimental design that improve the success of the methodology are discussed.

Dynamic force measurement↗
NASA NTRSDate not supplied

Practical Considerations using Weighted-Acceleration Compensation Techniques for Dynamic Force Measurements in Wind Tunnels

Most wind tunnel force measurement systems are designed and calibrated for high-accuracy static measurements, but may have limited ability to sense dynamic forces and moments. As a means to improve the measurement bandwidth of dynamic forces, researchers have proposed using a weighted-acceleration technique, which uses accelerometer data to compensate and correct for system dynamics. The sum of weighted-accelerations method is attractive as the acceleration data applies a correction to the traditional static measurements. The focus of this paper is on practical aspects of implementing a weighted-acceleration technique in an experimental arrangement. A formulation of the weighted-acceleration methodology is validated on a reduced-order model and demonstrated on a tabletop experiment that serves as a proxy to a wind tunnel force measurement system. As part of this system, a two component normal force and pitching moment balance was designed and fabricated. A static and dynamic calibration of the system was performed, and the weighted-acceleration technique was used to reconstruct impact forces acting on the system. Practical considerations of the experimental design that improve the success of the methodology are discussed.

Dynamic force measurement↗
NASA NTRS1994

Latitudinal variation of speed and mass flux in the acceleration region of the solar wind inferred from spectral broadening measurements

Spectral broadening measurements conducted at S-band (13-cm wavelength) during solar minimum conditions in the heliocentric distance range of 3-8 R(sub O) by Mariner 4, Pioneer 10, Mariner 10, Helios 1, Helios 2, and Viking have been combined to reveal a factor of 2.6 reduction in bandwidth from equator to pole. Since spectral broadening bandwidth depends on electron density fluctuation and solar wind speed, and latitudinal variation of the former is available from coherence bandwidth measurements, the remote sensing spectral broadening measurements provide the first determination of the latitudinal variation of solar wind speed in the acceleration region. When combined with electron density measurements deduced from white-light coronagraphs, this result also leads to the first determination of the latitudinal variation of mass flux in the acceleration region. From equator to pole, solar wind speed increases by a factor of 2.2, while mass flux decreases by a factor of 2.3. These results are consistent with measurements of solar wind speed by multi-station intensity scintillation measurements, as well as measurements of mass flux inferred from Lyman alpha observations, both of which pertain to the solar wind beyond 0.5 AU. The spectral broadening observations, therefore, strengthen earlier conclusions about the latitudinal variation of solar wind speed and mass flux, and reinforce current solar coronal models and their implications for solar wind acceleration and solar wind modeling.

Woo, Richard↗
NASA NTRS1996

Fiber Optic Sensors for Smart Materials and Structures

In this paper we describe recently developed fiber sensors which are capable of monitoring the health of smart-structures. The unobstrusive geometry of these sensors make them an excellent choice for embedding the sensor in composite materials to measure internal states of strain in structures and materials. Some of these sensors have gage lengths that can be tailored from tens of microns to many meters. We will describe various demodulation schemes (Pseudo-Heterodyne, Synthetic-Heterodyne, Homodyne, Differential-Cross Multiplier, and Single Channel Phase-Tracker) to obtain high bandwidth measurements, enabling measurement of static to high frequency impact generated strains with a dynamic response exceeding tens of thousands of microstrains. In addition, we will show that we can tailor the fiber sensor to either measure only strain and reject temperature response or measure only the temperature, or measure both temperature and strain simultaneously. We will also demonstrate the ability to measure multiple strain components inside a host simultaneously using a single fiber sensor embedded in the host using a certain sensor type and transverse strain immunity using another sensor type. Additionally we will show the ability to measure temperature up to 100 C using fiber optic sensors.

Singh, H.↗
NASA NTRS1980

Beamed microwave power transmitting and receiving subsystems radiation characteristics

Measured characteristics of the spectrum of typical converters and the distribution of radiated Radio Frequency (RF) energy from the terminals (transmitting antenna and rectenna) of a beamed microwave power subsystem are presented for small transmitting and receiving S-band (2.45 GHz) subarrays. Noise and harmonic levels of tube and solid-state RF power amplifiers are shown. The RF patterns and envelope of a 64 element slotted waveguide antenna are given for the fundamental frequency and harmonics through the fifth. Reflected fundamental and harmonic patterns through the fourth for a 42 element rectenna subarray are presented for various dc load and illumination conditions. Bandwidth measurements for the waveguide antenna and rectenna are shown.

Dickinson, R. M.↗
NASA NTRS1979

Radar observations of asteroid 1580 Betulia

Radar observations of the asteroid 1580 Betulia, made at a wavelength of 12.6 cm, show a mean radar cross section of 2.2 + or- 0.8 sq km and a total spectral bandwidth of 26.5 + or- 1.5 Hz. Combining bandwidth measurements with the optically determined rotation period sets a lower limit to the asteroid's radius of 2.9 + or- 0.2 km.

Pettengill, G. H.↗
NASA NTRS1983

On Io, all that flickers is not cold

The 4.8 micron flux from the Galilean satellite Io was shown to fluctuate with an amplitude of approximately 10 percent on time scales of every 28 seconds, 40 minutes, night-to-night, and perhaps year-to-year. Such behavior was found to be the result of random fluctuations for which the mean square fluctuation varies inversely with frequency for constant bandwidth measurement. The theory developed for thermionic emission from barium oxide cathodes in vacuum tubes might be applicable to this situation. If so, the fluctuations in the flux from Io's volcanoes may be caused by diffusion of hot convective cells onto the surface of Io. Long term fluctuations may furnish a means by which the Io volcanism can shut down and conserve energy. Thus the discrepancy that exists between measurements of the current heat flow from Io and calculations of tidal dissipation may be resolved. Tests for rapid flickering at 10 microns showed no fluctuations greater than one percent. This agrees with the prediction of the flow model theory in which the 10 microns volcanic thermal emission arises from cooling of old flows.

Sinton, W. M.↗
NASA NTRS2007

An Analysis of the Effects of RFID Tags on Narrowband Navigation and Communication Receivers

The simulated effects of the Radio Frequency Identification (RFID) tag emissions on ILS Localizer and ILS Glide Slope functions match the analytical models developed in support of DO-294B provided that the measured peak power levels are adjusted for 1) peak-to-average power ratio, 2) effective duty cycle, and 3) spectrum analyzer measurement bandwidth. When these adjustments are made, simulated and theoretical results are in extraordinarily good agreement. The relationships hold over a large range of potential interference-to-desired signal power ratios, provided that the adjusted interference power is significantly higher than the sum of the receiver noise floor and the noise-like contributions of all other interference sources. When the duty-factor adjusted power spectral densities are applied in the evaluation process described in Section 6 of DO-294B, most narrowband guidance and communications radios performance parameters are unaffected by moderate levels of RFID interference. Specific conclusions and recommendations are provided.

LaBerge, E. F. Charles↗
NASA NTRS2009

In-Phase Power-Combined Frequency Tripler at 300 GHz

This design starts with commercial 85- to 115-GHz sources that are amplified to as much as 250 mW using power amplifiers developed for the Herschel Space Observatory. The frequency is then tripled using a novel waveguide GaAs Schottky diode frequency tripler. This planar diode produces 26 mW at 318 GHz. Peak conversion efficiency is over 15 percent, and the measured bandwidth of about 265 - 30 GHz is limited more by the driving source than by the tripler itself. This innovation is based on an integrated circuit designed originally for a single-chip 260- to 340-GHz balanced tripler. The power-combined version has two mirror-image tripler chips that are power-combined in-phase in a single waveguide block using a compact Y-junction divider at the input waveguide, and a Y-junction combiner at the output waveguide. The tripler uses a split-block waveguide design with two independent DC bias lines.

Maestrini, Alain↗
NASA NTRS2014

Preliminary Results of the NASA Beacon Receiver for Alphasat Aldo Paraboni TDP5 Propagation Experiment

NASA Glenn Research Center (GRC) and the Politecnico di Milano (POLIMI) have initiated a joint propagation campaign within the framework of the Alphasat propagation experiment to characterize rain attenuation, scintillation, and gaseous absorption effects of the atmosphere in the 40 GHz band. NASA GRC has developed and installed a K/Q-band (20/40 GHz) beacon receiver at the POLIMI campus in Milan, Italy, which receives the 20/40 GHz signals broadcast from the Alphasat Aldo Paraboni TDP#5 beacon payload. The primary goal of these measurements is to develop a physical model to improve predictions of communications systems performance within the Q-band. Herein, we describe the design and preliminary performance of the NASA propagation terminal, which has been installed and operating in Milan since May 2014. The receiver is based upon a validated Fast Fourier Transform (FFT) I/Q digital design approach utilized in other operational NASA propagation terminals, but has been modified to employ power measurement via a frequency estimation technique and to coherently track and measure the amplitude of the 20/40 GHz beacon signals. The system consists of a 1.2-m K-band and a 0.6-m Qband Cassegrain reflector employing synchronous open-loop tracking to track the inclined orbit of the Alphasat satellite. An 8 Hz sampling rate is implemented to characterize scintillation effects, with a 1-Hz measurement bandwidth dynamic range of 45 dB. A weather station with an optical disdrometer is also installed to characterize rain drop size distribution for correlation with physical based models.

propagation↗
NASA NTRS2014

Ultrahigh Temperature Capacitive Pressure Sensor

Robust, miniaturized sensing systems are needed to improve performance, increase efficiency, and track system health status and failure modes of advanced propulsion systems. Because microsensors must operate in extremely harsh environments, there are many technical challenges involved in developing reliable systems. In addition to high temperatures and pressures, sensing systems are exposed to oxidation, corrosion, thermal shock, fatigue, fouling, and abrasive wear. In these harsh conditions, sensors must be able to withstand high flow rates, vibration, jet fuel, and exhaust. In order for existing and future aeropropulsion turbine engines to improve safety and reduce cost and emissions while controlling engine instabilities, more accurate and complete sensor information is necessary. High-temperature (300 to 1,350 C) capacitive pressure sensors are of particular interest due to their high measurement bandwidth and inherent suitability for wireless readout schemes. The objective of this project is to develop a capacitive pressure sensor based on silicon carbon nitride (SiCN), a new class of high-temperature ceramic materials, which possesses excellent mechanical and electric properties at temperatures up to 1,600 C.

Harsh, Kevin↗
NASA NTRS2015

Performance of the NASA Beacon Receiver for the Alphasat Aldo Paraboni TDP5 Propagation Experiment

NASA Glenn Research Center (GRC) and the Politecnico di Milano (POLIMI) have initiated a joint propagation campaign within the framework of the Alphasat propagation experiment to characterize rain attenuation, scintillation, and gaseous absorption effects of the atmosphere in the 40 gigahertz band. NASA GRC has developed and installed a K/Q-band (20/40 gigahertz) beacon receiver at the POLIMI campus in Milan, Italy, which receives the 20/40 gigahertz signals broadcast from the Alphasat Aldo Paraboni Technology Demonstration Payload (TDP) no. 5 beacon payload. The primary goal of these measurements is to develop a physical model to improve predictions of communications systems performance within the Q-band. Herein, we describe the design and preliminary performance of the NASA propagation terminal, which has been installed and operating in Milan since June 2014. The receiver is based upon a validated Fast Fourier Transform (FFT) I/Q digital design approach utilized in other operational NASA propagation terminals, but has been modified to employ power measurement via a frequency estimation technique and to coherently track and measure the amplitude of the 20/40 gigahertz beacon signals. The system consists of a 1.2-meter K-band and a 0.6-meter Q-band Cassegrain reflector employing synchronous open-loop tracking to track the inclined orbit of the Alphasat satellite. An 8 hertz sampling rate is implemented to characterize scintillation effects, with a 1-hertz measurement bandwidth dynamic range of 45 decibels. A weather station with an optical disdrometer is also installed to characterize rain drop size distribution for correlation with physical based models.

propagation↗
NASA NTRS1996

Fast 3D Net Expeditions: Tools for Effective Scientific Collaboration on the World Wide Web

Two new technologies, the FASTexpedition and Remote FAST, have been developed that provide remote, 3D (three dimensional), high resolution, dynamic, interactive viewing of scientific data. The FASTexpedition permits one to access scientific data from the World Wide Web, take guided expeditions through the data, and continue with self controlled expeditions through the data. Remote FAST permits collaborators at remote sites to simultaneously view an analysis of scientific data being controlled by one of the collaborators. Control can be transferred between sites. These technologies are now being used for remote collaboration in joint university, industry, and NASA projects. Also, NASA Ames Research Center has initiated a project to make scientific data and guided expeditions through the data available as FASTexpeditions on the World Wide Web for educational purposes. Previously, remote visualization of dynamic data was done using video format (transmitting pixel information) such as video conferencing or MPEG (Motion Picture Expert Group) movies on the Internet. The concept for this new technology is to send the raw data (e.g., grids, vectors, and scalars) along with viewing scripts over the Internet and have the pixels generated by a visualization tool running on the viewers local workstation. The visualization tool that is currently used is FAST (Flow Analysis Software Toolkit). The advantages of this new technology over using video format are: (1) The visual is much higher in resolution (1280x1024 pixels with 24 bits of color) than typical video format transmitted over the network. (2) The form of the visualization can be controlled interactively (because the viewer is interactively controlling the visualization tool running on his workstation). (3) A rich variety of guided expeditions through the data can be included easily. (4) A capability is provided for other sites to see a visual analysis of one site as the analysis is interactively performed. Control of the analysis can be passed from site to site. (5) The scenes can be viewed in 3D using stereo vision. (6) The network bandwidth for the visualization using this new technology is much smaller than when using video format. (The measured peak bandwidth used was 1 Kbit/sec whereas the measured bandwidth for a small video picture was 500 Kbits/sec.) This talk will illustrate the use of these new technologies and present a proposal for using these technologies to improve science education.

Watson, Val↗
NASA NTRS1977

Systems for measuring response statistics of gigahertz bandwidth photomultipliers

New systems have been developed for measuring the average impulse response, the pulse-height spectrum, the transit-time statistics as a function of signal level, and the dark-count spectrum of gigahertz bandwidth photomultipliers. Measurements showed that the 0.53 microns pulse used as an optical test source had a 30 picoseconds and less than 70 ps pulse width. Calibration data showed the system resolution to be less than 20 ps for root mean square transit-time measurements. Test data for a static crossed-field photomultiplier showed 2-photoelectron resolution and less than 30-ps time jitter over the 1- to 100-photoelectron range.

Abshire, J. B.↗
NASA NTRS1995

Determination of attitude jitter in small satellites

For various reasons, including cost, small satellites are becoming more appealing. Because of their smaller inertias, these spacecrafts are more sensitive to disturbances and likely to have more attitude jitter than the bigger units. These jitter levels may be unacceptable for some scientific instruments and need to be compensated. In the case of line-of-sight type instruments, the attitude jitter could be mitigated by incorporating a fast steering mirror into the system. To take full advantage of these devices, the spacecraft attitude needs to be measured at sufficiently high bandwidth, well beyond what is commonly provided by inertial reference units. This research examines various ways to obtain higher bandwidth attitude measurements for the purpose of jitter control.

Algrain, Marcelo C.↗
NASA NTRS1992

The Galileo plasma wave investigation

The purpose of the Galileo plasma wave investigation is to study plasma waves and radio emissions in the magnetosphere of Jupiter. The plasma wave instrument uses an electric dipole antenna to detect electric fields, and two search coil magnetic antennas to detect magnetic fields. The frequency range covered is 5 Hz to 5.6 MHz for electric fields and 5 Hz to 160 kHz for magnetic fields. Low time-resolution survey spectrums are provided by three on-board spectrum analyzers. In the normal mode of operation the frequency resolution is about 10 percent, and the time resolution for a complete set of electric and magnetic field measurements is 37.33 s. High time-resolution spectrums are provided by a wideband receiver. The wideband receiver provides waveform measurements over bandwidths of 1, 10, and 80 kHz. Compared to previous measurements at Jupiter this instrument has several new capabilities. These new capabilities include (1) both electric and magnetic field measurements to distinguish electrostatic and electromagnetic waves, (2) direction finding measurements to determine source locations, and (3) increased bandwidth for the wideband measurements.

Gurnett, D. A.↗