Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “materials database”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2026

Mechanical Design and Operation of a Novel Lunar Environment Structural Test Rig (LESTR)

The Lunar Environment Structural Test Rig (LESTR) was developed to address a critical gap in mechanical property data for metal alloy wire materials under lunar-relevant conditions down to 40 K. Conventional aerospace material databases provide thermophysical properties for bulk metals over a wide temperature range, but validated mechanical and physical property data below 77 K, particularly for small-diameter wires, remain limited and are generally the exception rather than the rule. These conditions are essential for Artemis mission hardware such as shape memory alloy (SMA) rover tires. LESTR’s design requirements were to combine a high-stiffness electrodynamic load frame with closed- cycle cryogenic cooling, high-vacuum capability (10–6 torr), and noncontact optical strain measurement to enable tensile, four-point bend, and fatigue testing of wires or other materials and geometries at temperatures from 40 to 125 K. These considerable requirements were merged with the need to lower the barrier of testing for the end user as measured in terms of cost-per-test cycle, safety improvement, and reduction in upkeep costs associated with state-of-the-art solutions associated with cryomechanical material characterization. The system incorporates modular gripping and alignment fixtures; precision thermal management using cryocoolers and embedded heaters; and integrated instrumentation for displacement, load, temperature, and vacuum control. Calibration procedures establish correlations between tooling and specimen temperature, ensuring accurate thermal conditions across the design envelope unbound by cryofluid conditions in heritage immersion-based test systems. Initial validation tests using Inconel (Special Metals Corp.) wire demonstrated accurate ultimate strength and post-yield behavior. The load frame operation was also verified under representative service conditions, including thermal cycling and prolonged fatigue loading. By generating mechanical property data at ultralow temperatures, LESTR fills a critical gap in existing materials databases and provides a scalable platform for iterative alloy development and durability assessment for planetary hardware. This capability supports NASA’s long-term objectives for surface exploration by enabling design confidence for components operating in extreme cryogenic environments.

LESTR↗
NASA NTRS2002

A Computer Code for Gas Turbine Engine Weight And Disk Life Estimation

Reliable engine-weight estimation at the conceptual design stage is critical to the development of new aircraft engines. It helps to identify the best engine concept amongst several candidates. In this paper, the major enhancements to NASA's engine-weight estimate computer code (WATE) are described. These enhancements include the incorporation of improved weight-calculation routines for the compressor and turbine disks using the finite-difference technique. Furthermore, the stress distribution for various disk geometries was also incorporated, for a life-prediction module to calculate disk life. A material database, consisting of the material data of most of the commonly-used aerospace materials, has also been incorporated into WATE. Collectively, these enhancements provide a more realistic and systematic way to calculate the engine weight. They also provide additional insight into the design trade-off between engine life and engine weight. To demonstrate the new capabilities, the enhanced WATE code is used to perform an engine weight/life trade-off assessment on a production aircraft engine.

Tong, Michael T.↗
NASA NTRS1995

Numerical Methodology For Full-Body TPS Sizing And Optimization For Access-To-Space Vehicles

This paper presents details of the methodology and numerical procedures developed at NASA Ames for full-body TEXAS sizing and optimization for Access to Space vehicle concepts. The core of the procedures is a robust implicit solver for one dimensional transient heat conduction in reusable multilayer TEXAS stackups. The solver includes an arbitrary number of material layers, contact resistances between materials, temperature and pressure dependent material and surface properties, numerous boundary-condition options, and self-adaptive time stepping. The solver is coupled with the Access-to-Space material database of 23 candidate TPS and structural materials and a thermal-environment database obtained from trajectory-based fullbody Navier-Stokes computations of the external flowfield. The thermal environment and material response are coupled through the use of T-type heat transfer coefficients. TIPS sizing and weight optimization are performed at every surface point on the vehicle based on sizing constraints which include material temperature limits, maximum backwall temperature, and cumulative interior heat flux. Typical results are presented for a lifting body concept with 10000 surface points, which required 35 minutes to compute on an SGI Indigo 2.

Milos, Frank S.↗
NASA NTRSDate not supplied

Capturing, Analyzing, Maintaining, and Disseminating Shape Memory Material Data Between Information Management Systems

With an increased demand on reducing the time, cost, and effort to develop new materials, Integrated Computational Materials Engineering (ICME) has received widespread attention in various engineering disciplines as a catalyst for significantly reducing experimental testing during the material design process. An ICME approach to design can enable ‘fit-for-purpose’ materials to be realized in engineering applications by incorporating well-understood process-property-performance relationships between the various length and time scales in a material’s structure, enabling material optimization. However, such an approach requires validated multiscale models at the various length scales for a material, which in turn requires a large amount of data, a robust means of storing the data, and the ability to link data to developed material models. The NASA Vision 2040 [1] has identified nine key elements to enabling ICME approaches in system level design, with one being “Data, Information, and Visualization”, thus outlining the importance of a robust information management system for ICME. As the relationship between microstructure, properties, and material performance become better understood and incorporated into multiscale models that can be leveraged in application design, the emergence of new materials with application-driven properties can be realized. One such new material class that has seen growing attention are shape memory materials (SMM), in which a material can transition between a deformed and undeformed state via a reversible phase transformation when subject to a thermal, mechanical, or magnetic load [2]. SMMs have been used widely in aerospace and biomedical industries, including applications such as actuators, low-shock mechanisms, medical staples, braces, and stents [3, 4]. These materials exhibit unique behavior due to their ability to transition between phases, and thus the mechanisms that enable this transition must be captured in a data information management system and incorporated into SMM material models. At NASA Glenn Research Center, the Shape Memory Materials Database (SMMD) Tool has been developed to capture the necessary information that governs SMM material behavior and provide users the ability to select and visualize various SMMs for a specific application [5]. The database contains point-wise data for published SMM materials, along with the pedigree metadata for traceability necessary for a robust information management system. The database is also capable of storing in-house test data performed at NASA GRC by interacting with the developed Shape Memory Alloy (SMA) Analytics tool to extract the necessary point-wise values and populate the database. Although the SMMD Tool offers its users a single, authoritative source for SMM material data that is critical for model development and material design, the full material pedigree of the in-house test data for SMMs is not currently captured and is out of the scope for the SMMD tool. In this work, the schema for capturing SMM test data within the larger NASA GRC ICME Schema [6, 7, 8, 9] will be developed and implemented for thermomechanical tests conducted at NASA GRC. The developed schema will not only store the relevant data needed for the SMMD tool, but also the material pedigree (i.e., production of the bulk material, bulk material analysis, sample cut-out diagrams, sample fabrication procedure, etc.), test pedigree (i.e., test equipment used, measurement systems used, raw test data), and analysis pedigree (i.e., how the data in the SMMD tool is calculated). Furthermore, a Python-based framework will be developed to seamlessly interact between the SMA Analytics and SMMD tools, which will write the full dataset and associated metadata to the GRC Information Management System before passing the required point-wise data to the SMMD tool. Data informatics is a key element of the NASA Vision 2040, which requires not only that data is stored and maintained throughout the material lifecycle, but that the data is also accessible and reusable such that material development efforts can be minimized. Therefore, for an ICME design approach to be realized, a centralized information management system that drives the ICME process must be able to communicate with other databases. The work that will be presented in this presentation will therefore not only demonstrate the ability of NASA GRC’s information management system to capture SMM data, but also its ability to interact with pre-existing tools specialized for such materials.

Data management↗
NASA NTRS2023

NASA GRC ICME Schema for Materials Data Management: An Executive Summary

Integrated Computational Materials Engineering (ICME) has received a growing emphasis in attention due its potential impact on rapid material design, reduction in cost and time to market for new applications, and the promise of ‘fit-for-purpose’ materials coupled with recent advances in high performance computing and material characterization tools. However, for an organization to implement ICME practices for material discovery and design, a series of both technical and cultural challenges must be overcome to foster an environment that enables efficient, traceable, and predictive multiscale simulations of material behavior to enable virtual design of materials. In 2016, NASA sponsored a 2040 Vision study to define the potential 25-year future state required for integrated multiscale modeling of materials and systems to improve both the associated time and cost for aerospace and aeronautical innovation. The study envisions a cyber-physical-social ecosystem of experimentally validated computational models, tools, and techniques, along with the associated digital tapestry, that can enable rapid, optimized, ‘fit-for-purpose’ design of materials, components, and systems. A key requirement for such an ecosystem is the development of a robust information management system for materials across their full lifecycle, including material pedigree, experimental (real) and virtual (simulation) data, developed material models, and the implementation of models in engineering applications, such that process-structure-property-performance relationships can be established, thereby enabling the virtual design and optimization of materials. Such an information management system must be able to effectively capture: i) material information at each length scale; ii) test data and analysis; iii) associated material models; and iv) material and model deployment in engineering applications. These systems must also provide traceability between experimental and virtual representations of the material to ensure, when appropriate, the material digital twin is maintained. Additionally, this robust material information management system must be able to seamlessly connect with both commercial and an organization’s in-house software tools, be they analysis tools, other material databases, product lifecycle management (PLM) or simulation data management (SDM) tools, etc., such that automation of the design and analysis of a material across multiple length scales is possible. In this paper, an executive summary of the NASA GRC ICME Schema for materials information management is presented. The database best practices and schema design philosophy specifically for ICME materials data management and an overview description of each element in the schema is given, along with its associated role in an ICME workflow. Additionally, auxiliary tools that interact with the database and provide judicious automation with regards to importing, exporting, and analyzing materials data are presented. Such tools are critical to an ICME ecosystem, not only for their role in enabling optimization, but also in relieving users of tedious manual tasks, thus helping to promote adoption and combat the cultural challenges organizations face in enabling ICME.

Materials↗
NASA NTRSDate not supplied

Material Characterization and Modeling of Room Temperature Vulcanizing Silicone

Room Temperature Vulcanizing silicone (RTV) is a high-temperature adhesive that has successfully been used as a gap-filler between Thermal Protection System (TPS) tiles for heatshields on numerous missions. It is also used to bond instrumentation plugs such as temperature and pressure sensors into the heatshields. While RTV has been traditionally assumed to be a non-porous and non-ablating material, numerous experiments have shown that RTV pyrolyzes and becomes highly porous as it is heated. Heating RTV has also shown swelling, or intumescence, which can pose unique problems that lead to roughness induced boundary-layer transition, surface oxide formation and contamination of heat shield sensors. Therefore, it is crucial to understand and model the intumescence phenomenon of RTV. As data for RTV material properties is limited, the first step in modeling RTV is to collect material properties such as pyrolysis mass-loss, microstructure change, virgin and char porosity, etc. which was performed in our initial study. Additionally, thermomechanical properties such as Young’s modulus and Poisson ratio are required for modeling the intumescence of RTV, which were taken from literature and the coefficient of thermal expansion was collected using in-situ heating and Micro Computed Tomography (µ-CT) in previous studies. Finally, numerous other properties such as pyrolysis gas properties, virgin and char thermal conductivity and specific heat were compiled from previous experiments and literature into a material database that can be used for simulations. In Porous Material Analysis Toolbox based on OpenFOAM (PATO) [4], structural mechanics coupled with material response was used for simulating the intumescence of RTV as it is heated. However, since the permeability of the material is very low, the pyrolysis gas creates an internal pressure build-up as the material is being heated, significantly contributing to the deformation of the material. To correctly characterize this phenomenon, additional physics models were implemented into PATO's stress analysis solver, and results were compared with RTV dilatometry test data as a preliminary verification case. Future work will include experiments of RTV at the Plasmatron X facility and the in-situ heating cell with µ-CT, and improvement of simulation tools to more accurately model RTV intumescence.

TPS↗
NASA NTRSDate not supplied

Material Properties and Modeling of Room Temperature Vulcanizing Silicone

Room Temperature Vulcanizing silicone (RTV) is a high-temperature adhesive that has successfully been used as a gap-filler between Thermal Protection System (TPS) tiles for heatshields on numerous missions. It is also used to bond instrumentation plugs such as temperature and pressure sensors into the heatshields. While RTV has been traditionally assumed to be a non-porous and non-ablating material, numerous experiments have shown that RTV pyrolyzes and becomes highly porous as it is heated. Heating RTV has also shown swelling, or intumescence, which can pose unique problems that lead to roughness induced boundary-layer transition, surface oxide formation and contamination of heat shield sensors. Therefore, it is crucial to understand and model the intumescence phenomenon of RTV. As data for RTV material properties is limited, the first step in modeling RTV is to collect material properties such as pyrolysis mass-loss, microstructure change, virgin and char porosity, etc. which was performed in our initial study. Additionally, thermomechanical properties such as Young’s modulus and Poisson ratio are required for modeling the intumescence of RTV, which were taken from literature and the coefficient of thermal expansion was collected using in-situ heating and Micro Computed Tomography (µ-CT) in previous studies. Finally, numerous other properties such as pyrolysis gas properties, virgin and char thermal conductivity and specific heat were compiled from previous experiments and literature into a material database that can be used for simulations. In Porous Material Analysis Toolbox based on OpenFOAM (PATO) [4], structural mechanics coupled with material response was used for simulating the intumescence of RTV as it is heated. However, since the permeability of the material is very low, the pyrolysis gas creates an internal pressure build-up as the material is being heated, significantly contributing to the deformation of the material. To correctly characterize this phenomenon, additional physics models were implemented into PATO's stress analysis solver, and results were compared with RTV dilatometry test data as a preliminary verification case. Future work will include experiments of RTV at the Plasmatron X facility and the in-situ heating cell with µ-CT, and improvement of simulation tools to more accurately model RTV intumescence.

PATO↗
NASA NTRS1990

A software system for laser design and analysis

A laser-material database and laser-modeling software system for designing lasers for laser-based Light Detection And Ranging (LIDAR) systems are presented. The software system consists of three basic sections: the database, laser models, and interface software. The database contains the physical parameters of laser, optical, and nonlinear materials required by laser models. The models include efficiency calculations, electrooptical component models, resonator, amplifier, and oscillator models, and miscellaneous models. The interface software provides a user-friendly interface between the user and his personal data files, the database, and models. The structure of the software system is essentially in place, while future plans call for upgrading the computer hardware and software in order to support a multiuser multitask environment.

Cross, P. L.↗
NASA NTRS2004

Electron Emission Properties of Insulator Materials Pertinent to the International Space Station

We present the results of our measurements of the electron emission properties of selected insulating and conducting materials used on the International Space Station (ISS). Utah State University (USU) has performed measurements of the electron-, ion-, and photon-induced electron emission properties of conductors for a few years, and has recently extended our capabilities to measure electron yields of insulators, allowing us to significantly expand current spacecraft material charging databases. These ISS materials data are used here to illustrate our various insulator measurement techniques that include: i) Studies of electron-induced secondary and backscattered electron yield curves using pulsed, low current electron beams to minimize deleterious affects of insulator charging. ii) Comparison of several methods used to determine the insulator 1st and 2nd crossover energies. These incident electron energies induce unity total yield at the transition between yields greater than and less than one with either negative or positive charging, respectively. The crossover energies are very important in determining both the polarity and magnitude of spacecraft surface potentials. iii) Evolution of electron emission energy spectra as a function of insulator charging used to determine the surface potential of insulators. iv) Surface potential evolution as a function of pulsed-electron fluence to determine how quickly insulators charge, and how this can affect subsequent electron yields. v) Critical incident electron energies resulting in electrical breakdown of insulator materials and the effect of breakdown on subsequent emission, charging and conduction. vi) Charge-neutralization techniques such as low-energy electron flooding and UV light irradiation to dissipate both positive and negative surface potentials during yield measurements. Specific ISS materials being tested at USU include chromic and sulfuric anodized aluminum, RTV-silicone solar array adhesives, solar cell cover glasses, Kapton, and gold. Further details of the USU testing facilities, the instrumentation used for insulator measurements, and the NASA/SEE Charge Collector materials database are provided in other Spacecraft Charging Conference presentations (Dennison, 2003b). The work presented was supported in part by the NASA Space Environments and Effects (SEE) Program, the Boeing Corporation, and a NASA Graduate Fellowship. Samples were supplied by Boeing, the Environmental Effects Group at Marshall Space Flight Center, and Sheldahl, Inc.

Thomson, C. D.↗
NASA NTRSDate not supplied

Digitally-Engineered Impact Resistant Aerogel Composites for MMOD Protection (DIRAC-MP)

This project implemented a digital-engineering approach to optimize the impact absorption performance of polymer aerogels and aerogel-based composites for Micrometeoroids and Orbital Debris (MMOD) containment. We developed a curated materials database and a machine-learning framework to derive composition-response relationships, enabling predictive design and targeted material selection. In support of experimental validation, a split Hopkinson pressure bar (SHPB) test rig, specifically adapted for low-density aerogel materials, was designed and built in-house. This project accelerates the development of new aerogel formulations, producing candidate materials tailored for enhanced impact-absorption behavior.

Sadeq Malakooti↗
NASA NTRS1990

A database for solid-state laser, optical, and nonlinear materials

The database contains the physical properties of laser, optical, and nonlinear materials used by the laser models of a laser-modeling software system. The database is subdivided into two parts: spectra and tabulated data. The spectra are ASCII files of laser-material's absorption and emission spectra, and laser-diode's emission spectra. The tabulated data contains physical properties of laser, optical, and nonlinear materials, including crystalline, thermal, and mechanical properties. A menu-driven interface allows the execution from a personal directory where the user can store files containing input parameters for a specific model or the results of model's calculations.

Cross, P. L.↗
NASA NTRSDate not supplied

A Historical Overview of the NASA Orbital Debris Program Office’s Laboratory Optical Measurements

The NASA Orbital Debris Program Office (ODPO) has used laboratory measurements to help bring ground-based measurements together with models to ascertain Earth-orbiting target parameters of interest to support various orbital debris models. In 2005, the Optical Measurement Center (OMC) was established to simulate space-based illumination conditions using equipment and techniques that recreate telescopic observations, particularly source-target-sensor orientations. The intent was to recreate light curves using known aspect angles of known targets and phase angles (angle is defined by the vertex between illumination source-object-detector) to complement telescopic observations that could be used to update the current optical size estimation model (OSEM) – a model that converts object brightness into size for orbital debris models. To support the above goals, the laboratory has undergone several equipment upgrades to increase capabilities over almost 20 years of operation. The primary instrumentation acquires reflectance measurements and includes a solar-like light source, CCD camera with astrometric filters, and robotic arm. A rotary arm was added approximately five years after full operation to allow acquisition through a full 360° range of phase angles. Another part of the OMC instrumentation is a field spectrometer, predominately used for field operations to acquire pre- and post-flight spacecraft material spectral measurements. Additionally, reflectance spectroscopy of various materials is also of interest resulting from hypervelocity impact tests, pristine spacecraft materials, or samples of materials that are used in spacecraft design. These measurements are stored in NASA’s Spectral Material Database, a resource that is still being populated today. The study of spectral measurements also enabled the development of spectral unmixing routines to support the identification of spacecraft materials from spectral data gathered by ground based telescopes. Preliminary OMC investigations focused on feasibility studies to acquire 360° rotation light curves of simple shapes at a single-phase angle and extended to measurements of representative fragments from ground-based explosion tests. To correlate the light curves with ground-based optical measurements, a focused study on high area to mass materials was conducted in support of a newly identified population (at the time) in geosynchronous orbit (GEO) consisting of multi-layered insulation. To further characterize orbital debris, a larger selection of materials was analyzed using laboratory photometric measurements that included representative targets from pristine spacecraft materials and ground-based impact tests. Around 2012, an initiative was requested to understand the feasibility of active debris removal (ADR) of larger targets using grappling methods for spent rocket bodies. Using a priori information on selected targets, scaled-down versions of rocket bodies were generated thanks to improvements in 3D printing technology and machining. These targets were studied in the OMC to understand rotation characteristics. These were compared with telescopic data to determine if the tumble and rotation angles would allow ADR. In 2013, the OMC focused on combining spectral measurements with photometric data to characterize GEO orbital debris. Several years later, NASA acquired a Titan III Transtage test article from “The Boneyard” with a high-resemblance to on-orbit Titan III Transtage rocket bodies, allowing physical access to a representative rocket body that suffered fragmentations in GEO. This prompted the creation of 3D models using lidar technology and spectral measurements of the materials. Focused research also transitioned to specific materials (i.e., solar cells) when telescopic surveys requested characterization of specific GEO targets. In the different research products presented, the focus has been to understand the various parameters that influence optical size estimation, including albedo, phase functions, and brightness variations. Work in this area continues with newer sources of data, including DebriSat, a high-fidelity 56-kg spacecraft replica representative of a modern low Earth orbit (LEO) satellite subjected to a laboratory hypervelocity impact test to understand fragmentation events and to support updates to satellite breakup models and size estimation models. Utilizing the vast population of fragments from DebriSat and prior laboratory impact experiments, the ODPO has focused on acquiring bidirectional reflectance distribution function (BRDF) data to characterize targets in the laboratory, thus removing aspect angle dependencies. Additionally, the DebriSat project has provided improved processes for measuring size via image acquisition, such that a true fragment size can be directly compared to the derived size using the OSEM. The team continues to assess BRDFs and use spectral measurement data to investigate the parameters used in the OSEM, specifically magnitudes, albedo, and phase functions.

Heather Cowardin↗
NASA NTRS1993

An evaluation of ablative materials for a lunar transfer vehicle aerobrake

An evaluation of the utility of an ablative thermal protection system (TPS) for use on a lunar mission return aerobrake has been completed. Requirements are established and criteria developed specifically for the ablator application. A quantitative and qualitative multi-attribute utility analysis is employed to establish a relative ranking among candidates and a performance threshold. A review of the applicable existing ablator material database is made and appropriate thermochemical/melting ablation analysis is employed to evaluate thermal performance. Ablatives are shown to be potentially both performance capable and cost effective in single-use roles. Reusable surface insulation is also shown to be competitive as an ablator with certain modifications.

Lane, J. G.↗
NASA NTRS1994

Development of processing techniques for advanced thermal protection materials

The effort, which was focused on the research and development of advanced materials for use in Thermal Protection Systems (TPS), has involved chemical and physical testing of refractory ceramic tiles, fabrics, threads and fibers. This testing has included determination of the optical properties, thermal shock resistance, high temperature dimensional stability, and tolerance to environmental stresses. Materials have also been tested in the Arc Jet 2 x 9 Turbulent Duct Facility (TDF), the 1 atmosphere Radiant Heat Cycler, and the Mini-Wind Tunnel Facility (MWTF). A significant part of the effort hitherto has gone towards modifying and upgrading the test facilities so that meaningful tests can be carried out. Another important effort during this period has been the creation of a materials database. Computer systems administration and support have also been provided. These are described in greater detail below.

Selvaduray, Guna S.↗
NASA NTRS1997

Validation of Framework Code Approach to a Life Prediction System for Fiber Reinforced Composites

The grant was conducted by the MMC Life Prediction Cooperative, an industry/government collaborative team, Ohio Aerospace Institute (OAI) acted as the prime contractor on behalf of the Cooperative for this grant effort. See Figure I for the organization and responsibilities of team members. The technical effort was conducted during the period August 7, 1995 to June 30, 1996 in cooperation with Erwin Zaretsky, the LERC Program Monitor. Phil Gravett of Pratt & Whitney was the principal technical investigator. Table I documents all meeting-related coordination memos during this period. The effort under this grant was closely coordinated with an existing USAF sponsored program focused on putting into practice a life prediction system for turbine engine components made of metal matrix composites (MMC). The overall architecture of the NMC life prediction system was defined in the USAF sponsored program (prior to this grant). The efforts of this grant were focussed on implementing and tailoring of the life prediction system, the framework code within it and the damage modules within it to meet the specific requirements of the Cooperative. T'he tailoring of the life prediction system provides the basis for pervasive and continued use of this capability by the industry/government cooperative. The outputs of this grant are: 1. Definition of the framework code to analysis modules interfaces, 2. Definition of the interface between the materials database and the finite element model, and 3. Definition of the integration of the framework code into an FEM design tool.

Gravett, Phillip↗
NASA NTRS2000

Long-Term Durability Analysis of a 100,000+ Hr Stirling Power Convertor Heater Head

DOE and NASA have identified Stirling Radioisotope Power Systems (SRPS) as the power supply for deep space exploration missions the Europa Orbiter and Solar Probe. As a part of this effort, NASA has initiated a long-term durability project for critical hot section components of the Stirling power convertor to qualify flight hardware. This project will develop a life prediction methodology that utilizes short-term (t < 20,000 hr) test data to verify long-term (t > 100,000 hr) design life. The project consists of generating a materials database for the specific heat of alloy, evaluation of critical hermetic sealed joints, life model characterization, and model verification. This paper will describe the qualification methodology being developed and provide a status for this effort.

Bartolotta, Paul A.↗