SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This poster presents on flows of resources that support manufacturing, including flows of energy and materials. It highlights the recent and current strategic analysis efforts such as energy and carbon footprints, case studies showing the interconnectedness between sectors and global perspective and competitiveness, NREL's Materials Flows through Industry (MFI) tool; and our big impact report on Sustainable Manufacturing and Circular Economy.
Organic anolyte materials for redox flow batteries and redox flow batteries containing organic anolyte materials are disclosed.
Flow boiling heat transfer tests were conducted to evaluate the Critical Heat Flux (CHF) and Heat Transfer Coefficient (HTC) of conventional and accident tolerant fuel (ATF) cladding materials, i.e., bare Zircaloy-4 (Zr4), and Zircaloy-4 coated with Chromium using physical vapor deposition (PVD) (Zr4-Cr-PVD) and cold spray process (Zr4-Cr-CS), respectively. The tests were performed on a single heater rod with a uniform heat flux profile, at the atmospheric pressure, inlet temperature (24 °C) and mass flow rate (750 kg/m 2 s). HTC’s were increased by 5.2% and 3.3% on Zr4-Cr-CS compared to bare Zr4 and Zr4-Cr-PVD. Improved HTCwas attributed to the increased void fraction and high roughness (Ra = 532 nm) of the Zr4-Cr-CS. In detail, the micro-cavities, which act as bubble seeds, were entirely distributed on the Zr4-Cr-CS, and these micro-cavities generated smaller and faster bubbles, thus the void fraction increased by 10.9% compared to bare Zr4. HTC is improved by these smaller and faster bubbles which can remove heat from the heater rod surface more efficiently. To identify the exact location of CHF, the surface temperature profile was measured using advanced fiber-optic sensors which have high temporal/spatial resolution (distance between point to point: ~2.5 mm, frequency ~100 Hz). CHF occurred at 80–95% along the heated length and showed an 11.6% reduction on Zr4-Cr-CS compared to bare Zr4. We hypothesize the CHF reduction was caused by the lower wettability of the Zr4-Cr-CS which reduces the liquid supply to the surface, and vigorous bubble accumulation owing to high void fraction near the outlet, which results in early formation of the vapor film. During the post-CHF quenching phase, the rougher Zr4-Cr-CS showed larger cooling rates compared to the bare Zr4 and Zr4-Cr-PVD, preventing of oxidation by chromium layer. In conclusion, we demonstrate that the high roughness on the Zr4-Cr-CS increased the number of micro-cavities on the surface, resulting in 5.2% increase in HTC and improvement in the quenching heat transfer performance whereas CHF was 11.6% reduced compared to bare Zr4. Overall statistically there is little effect in the coating with regards to CHF and slight improvement in HTC.
Aqueous organic redox flow batteries (AORFBs) have gained popularity in renewable energy storage due to their low cost, environmental friendliness and scalability. The rapid discovery of aqueous soluble organic (ASO) redox-active materials necessitates efficient machine learning surrogates for predicting battery performance. The physics-guided continual learning (PGCL) method proposed in this study can incrementally learn data from new ASO electrolytes while addressing catastrophic forgetting issues in conventional machine learning. Using a AORFB database with a thousand potential materials generated by a 780 $\text{cm}^2$ interdigitated cell model, PGCL incorporates AORFB physics to optimize the continual learning task formation and training strategies to retain previously learned battery material knowledge. Finally, the trained PGCL demonstrates its capability in assessing emerging ASO materials within the established parameter space when evaluated with the dihydroxyphenazine isomers.
The effective application of high-flow-stress materials in the realm of Solid Phase Processing frequently necessitates operating at elevated temperatures and substantially high force. These rigorous processing conditions give rise to intricate predicaments concerning the durability of the tools and dies involved, as well as the efficient utilization of process energy. This project is centered on the investigation of the fundamental scientific aspects inherent to these challenges. We aim to delve into the details of how materials react when subjected to intense shear forces at die interfaces, determine the metallurgical interactions occurring at the interfaces with the dies, and investigate the consequences of extreme temperatures on material flow, microstructural evolution, and resultant properties.
Accurate estimation of municipal solid waste (MSW) composition is critical for efficient waste management. In the United States, site-specific and material flow approaches determine the MSW composition at regional and national levels. The material flow-based national estimates are determined by the US EPA; the US EPA’s estimates are known to differ substantially from the aggregated tonnage of MSW managed by waste handling facilities in the United States. However, the material class-specific discrepancies of the US EPA’s material flow approach resulting in these differences are unknown. To find the basis of these discrepancies, we analyze the discarded MSW stream of 27 US states, which roughly accounts for 73 percent of the US population. Our analysis indicates that the material flow-based national estimates are accurate for the food, plastic, and glass material classes. In contrast, we find that the US EPA’s material flow-based predictions underestimate paper waste disposal by at least 15 million tons annually. These differences likely stem from incorrect assumptions of residence time. These results highlight the material class-specific strengths and drawbacks of the US EPA’s material flow-based MSW estimates.
As an advanced alternative to solid materials, Liquid Metals (LM) may offer more resilient and feasible Plasma Facing Components (PFCs). Particularly, regarding the unavoidable material erosion/degradation produced by particle/heat fluxes in future fusion devices where much longer duty cycles are expected. Furthermore, configurations that propose a flowing LM surface can add the advantage of a continuously fresh and clean layer facing the plasma. Although lithium is the most widely tested option, tin-lithium (SnLi) alloys have been proposed to attempt to combine the positive characteristics of both pure elements and ameliorate the specific issues of lithium. In this work, the potential use of Sn70Li30 alloy in such flowing concepts has been explored by addressing several preliminary and mandatory aspects for its utilization. Key issues such as wettability and compatibility of the alloy with relevant substrates have been studied in a multidisciplinary approach. The data obtained from deposited liquid tin-lithium droplets indicates approximate wetting temperatures of 360 °C, 390 °C and 405 °C for the fresh alloy on 316 stainless steel, molybdenum, and tungsten, respectively. However, the alloy contamination appeared to strongly affect the wetting characteristics of materials, increasing their wetting temperature by ~130 °C in the worst observed cases. Interestingly, in some instances, the instability of the liquid alloy surface was observed in the form of sudden gaseous ejection. The deposited droplets were posteriorly characterized in terms of absolute composition and depth profile by Inductively Coupled PlasmaOptical Emission Spectroscopy (ICP-OES) and Secondary Ion Mass Spectrometry (SIMS-ToF). Additionally, the nature and composition of the boundaries between the substrates and alloy microparticles was investigated by Scanning Electron Microscopy (SEM), Energy Dispersive X-Ray Spectroscopy (EDS), and 3D Laser microscopy. The overall results of this post-mortem characterization revealed that first signs of corrosion induced by both alloy elements (lithium-chromium association and iron-tin intermetallic mixing) were present on 316 stainless steel after short exposures (≤3 h) at temperatures lower than 550 °C. Conversely, molybdenum and tungsten showed good compatibility with the alloy in equivalent conditions. The global implications of these results are finally addressed, focusing on the future perspectives and the more viable scenarios for the eventual utilization of these alloys in flowing liquid metal configurations.
Many actions are underway at global, national, and local levels to address the plastic waste problem and transition toward a circular economy of plastics. Studies evaluating environmental and socioeconomic impacts of such a transition are lacking. Here, the purpose of this study is to conduct a national systems analysis of polyethylene terephthalate (PET) packaging supply chains in the United States. Material flow data was combined with environmental and socioeconomic indicators to evaluate and compare the sustainability of the linear PET packaging supply chain, current (2019) supply chain, and possible future circular supply chain options in the United States. Environmentally optimal circular US PET packaging material flows showed 31% and 38% savings of GHG emissions and energy demand, respectively, with a circularity of 77% when compared with a linear supply chain. Additionally, the environmentally optimal system showed higher employment (29%) and wages (31%) than a linear system, but with a 5% decrease in revenue generation. A socioeconomically optimal circular PET supply chain showed increased employment (by 52%), wages (by 67%), and revenues (by 1%), with a circularity of 59% when compared with the linear system. However, it showed 14% higher GHG emissions than a linear system, indicating a trade-off between environmentally and socioeconomically optimal circular PET packaging systems. Overall, linear-to-circular material flow transition may not necessarily lead to increased revenues and decreased environmental impacts of the entire system, but it does benefit society due to increased employment and wages. Future systems analysis work should focus on improving data quality for environmental and socioeconomic dimensions.
In 2019, the United States consumed over 57 million metric tons (MMT) of plastic with less than 7% recovered for reuse. This study provides an updated material flow analysis at national and regional scales for all durable and single-use plastics in the United States. From this material flow analysis, we develop a series of alternative future national plastic flow scenarios that envision a scale-up of recycling technologies, incorporating technical limitations and sorting infrastructure constraints. The results suggest that a maximum of 68% (24 MMT) of plastic waste could be diverted from landfills by scaling up existing commercial recycling technologies. Based on the current technological landscape, reaching near-zero waste is only possible if processes that are operating at pilot and laboratory scales can be effectively scaled and coupled with improved sorting infrastructure. Through these scenarios with increased recycling, the availability of postconsumer resin stocks could increase by 22–43 MMT.
The Photovoltaic Dynamic Material Flow Assessment (PV DMFA) model (also referred to here as “The model”) is a computational framework written in Python based on utility-scale PV electricity generation to quantify time-series stocks and flows of PV materials primarily in crystalline silicon PV technologies. The model evaluates cradle-to-cradle life cycle of utility-scale solar PV systems in the United States in the period 2000-2100. PV DMFA serves as a sustainability analysis tool to assess the impacts of different material circularity practices (i.e., reduce, reuse/refurbish, remanufacture, and recycle), PV module design shifts and sensitivity of material processing and technology related parameters to material installations, waste creation and raw material depletion in PV material supply chains. This tool enables advanced planning for future material needs and informs sustainable pathways for PV material management in the circular economy. This tool could be helpful to a wide range of stakeholders; Particularly, researchers and manufacturers looking for technoeconomic and/or environmental life cycle analysis (LCA) feedback for renewable energy (RE) systems.
Three-dimensional (3D) simulations of the structure of liquid crystal (LC) torons, topologically protected distortions of the LC director field, under material flows are rare but essential in microfluidic applications. Here, we show that torons adopt a steady-state configuration at low flow velocity before disintegrating at higher velocities, in line with experimental results. Furthermore, we show that under partial slip conditions at the boundaries, the flow induces a reversible elongation of the torons, also consistent with the experimental observations. These results are in contrast with previous simulation results for 2D skyrmions under similar flow conditions, highlighting the need for a 3D description of this LC soliton in relation to its coupling to the material flow. These findings pave the way for future studies of other topological solitons, like hopfions and heliknotons, in flowing soft matter systems.
Abstract Friction stir extrusion (FSE) is a novel solid-phase processing technique that consolidates and extrudes metal powders, flakes, chips, or billets into high-performance parts by plastic deformation, which has the potential to save substantial processing time and energy. Currently, most studies on FSE are experimental and only a few numerical models have been developed to explain and predict the complex physics of the process. In this work, a meshfree simulation framework based on smoothed particle hydrodynamics (SPH) was developed for FSE. Unlike traditional grid-based methods, SPH is a Lagrangian particle-based method that can handle severe material deformations, capture moving interfaces and surfaces, and monitor the field variable histories explicitly without complicated tracking schemes. These aspects of SPH make it attractive for the FSE process, where in situ evolution of field variables is difficult to observe experimentally. To this end, a 3-D, fully thermomechanically coupled SPH model was developed to simulate the FSE of aluminum wires. The developed model was thoroughly validated by comparing the numerically predicted material flow, strain, temperature history, and extrusion force with experimental results for a certain set of process parameters. The validated SPH model can serve as an effective tool to predict and better understand the extreme thermomechanical conditions during the FSE process.
Additive manufacturing (AM) or more commonly known as 3D-printing has gained much ground in industrial manufacturing because of its breakthrough in rapid prototyping and processes. To date, the 3D-printing market has grown significantly and is poised for growth in line with digitization of manufacturing. Furthermore, the main objective of this review article focuses on the viscoelastic behavior (viscous solution) of 3D printing materials at ambient conditions, which are not essentially under melt-flow or higher temperatures. The initial section reviews the basic concepts on viscosity and viscoelastic phenomenon, with emphasis on the preferred conditions a viscous material should have prior to 3D-printing. Several examples of structures formed from viscoelastic materials through 3D-printing are also detailed, as well as the various curing techniques for different printed objects or models. While there is much interest on industrial applications, the last part surveys various food formulations used for 3D-printing.
In this paper, we present the first demonstration of single-step gear manufacturing via an innovative in-situ friction stir forging approach. This novel process is a natural extension to the friction stir processing technique and relies on shear and normal stresses to form the complex shapes. Friction stir welding pin tool with shoulder is plunged at high revolutions per minute (rpm) into the sample to heat it to the desired temperature and enable plastic flow. Then, the tool is forged at high plunge rate to form the desired structurally-sound and defect free complex shapes. To better visualize the process the experiments are complemented by a 3D thermomechanically coupled, smoothed particle hydrodynamics (SPH) model to understand the material flow pattern both radially and through thickness in the gear teeth, plastic strain distribution, and temperature profile. We have demonstrated application of I-FSF to inherently poor formable AZ31 Mg, AA 7075-T6, and AA5083–10 vol% TiB 2 composite and fabricated 14-tooth spur gears from these materials with minimal farther machining. In conclusion, microstructure of the forged gears exhibited a directional material flow pattern due to the normal forging action and refinement of grains to 6–13 μm through dynamically recrystallization across the radial, through-thickness direction, which is in good agreement with the corresponding SPH simulation results.
A circular economy emphasizes the efficient use of all resources (e.g., materials, land, water). Despite anticipated overall benefits to society, the transition to a circular economy is likely to create regional differences in impacts. Current tools are unable to fully evaluate these potential externalities, which will be important for informing research prioritization and regional decision making. The Circular Economy Lifecycle Assessment and VIsualization (CELAVI) framework allows stakeholders to quantify and visualize potential regional and sectoral transfers of impacts that could result from transitioning to a circular economy, with particular focus on energy materials. The framework uses system dynamics to model material flows for multiple circular economy pathways and decisions are based on learning-by-doing and are implemented via cost and strategic value of different circular economy pathways. It uses network theory to track the spatial and sectoral flow of functional units across a graph and discrete event simulation to to step through time and evaluate lifecycle assessment data at each time step. The framework is designed to be flexible and scalable to accommodate multiple energy materials and multiple energy technologies. The primary goal of CELAVI is to help answer questions about how material flows and environmental and economic impacts of energy systems might change if the circularity of energy systems increases.
A circular economy emphasizes the efficient use of all resources (e.g., materials, land, water). Despite anticipated overall benefits to society, the transition to a circular economy is likely to create regional differences in impacts. Current tools are unable to fully evaluate these potential externalities, which will be important for informing research prioritization and regional decision making. The Circular Economy Lifecycle Assessment and VIsualization (CELAVI) framework allows stakeholders to quantify and visualize potential regional and sectoral transfers of impacts that could result from transitioning to a circular economy, with particular focus on energy materials. The framework uses system dynamics to model material flows for multiple circular economy pathways and decisions are based on learning-by-doing and are implemented via cost and strategic value of different circular economy pathways. It uses network theory to track the spatial and sectoral flow of functional units across a graph and discrete event simulation to to step through time and evaluate lifecycle assessment data at each time step. The framework is designed to be flexible and scalable to accommodate multiple energy materials and multiple energy technologies. The primary goal of CELAVI is to help answer questions about how material flows and environmental and economic impacts of energy systems might change if the circularity of energy systems increases.
Carbon (C) fixation, allocation, and metabolism by trees set the basis for energy and material flows in forest ecosystems and define their interactions with Earth’s changing climate. However, we lack a cohesive synthesis on how forest carbon fluxes vary globally with respect to climate and one another. Here, we draw upon 1,319 records from the Global Forest Carbon Database (ForC), representing all major forest types and the nine most significant autotrophic carbon fluxes, to comprehensively explore how C cycling in mature, undisturbed forests varies with latitude and climate on a global scale. We show that, across all flux variables analyzed, C cycling decreases continuously with absolute latitude – a finding that confirms multiple previous studies but contradicts the idea that net primary productivity of temperate forests rivals that of tropical forests. C flux variables generally displayed similar trends across latitude and multiple climate variables, with no differences in allocation detected at this global scale. Temperature variables in general, and mean annual temperature and temperature seasonality in particular, were the best univariate predictors of C flux, explaining 19 - 71% of variation in the C fluxes analyzed. The effects of temperature were modified by moisture availability, with C flux reduced under hot and dry conditions and sometimes under very high precipitation. C fluxes increased with growing season length, but this was never the best univariate predictor. Within the growing season, the influence of climate on C cycling was small but significant for a number of flux variables. These findings clarify how forest C flux varies with latitude and climate on a global scale. In a period of accelerating climatic change, this improved understanding of the fundamental climatic controls on forest C cycling sets a foundation for understanding patterns of change.
Explore the source record for details and available documents.