Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “material extrusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Extrusion‐Spheronization of Energetic Materials

The prevailing method to produce plastic‐bonded explosive (PBX) molding powder, or “prills”, is a complex, multiphase, and bespoke process that was developed by the high explosives (HEs) manufacturing industry several decades ago. This work demonstrates the utility of a simpler, widely‐used mechanical process—extrusion‐spheronization—to produce PBX prills. We begin by detailing precautions taken to enable safe remote operation of extrusion‐spheronization equipment with HE. We then perform a study investigating the effect of lacquer solvent composition on the particle packing, pressed density, and compressive strength properties of a 95 wt.% TATB/5 wt.% polymer binder formulation akin to PBX 9502. It was found that increased composition of low vapor pressure solvents caused prolonged retention of the solvent, resulting in tackier materials that would agglomerate and form larger prills. The larger prills also led to lower poured density and tapped density of HE prills and compressive strength of pressed PBX articles. The samples prepared with a 75% propyl acetate/25% butyl acetate lacquer solvent composition exhibited the highest compressive strength. However, it is believed that the prill packing and compressive strength properties are primarily driven by the prill size rather than the chemical composition of the lacquer itself. Extrusion‐spheronization remains a promising method to reliably and repeatably produce HE prills that is less sensitive to feedstock or process variation than traditional methods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Extrusion‐Spheronization of Mock Energetic Materials

The primary method for producing plastic bonded explosive (PBX) granules, or “prills”, has remained relatively unchanged for 70 years despite the complex nature of the process. In this work, we demonstrate the feasibility of using an extrusion‐spheronization technique to produce prills for PBX applications. We begin by detailing an inert formulation with similar properties of PBXs and then demonstrate the extrusion‐spheronization processing of these materials. A study is then performed where the spheronization process time of the extruded materials is varied and the resultant prills are morphologically characterized. Further, these prills are then pressed into high‐density articles and subject to compression testing to elucidate trends in process, properties, and performance. It was found that, for our formulation (95 wt.% melamine/5 wt.% polymer binder) and process, a spheronization time of 60 s yielded relatively uniform particles that exhibited improved poured, tapped, and pressed densities. Mechanical strength did not have a strong trend with process time as all spheronized materials had similar peak compression stress at failure. After further optimization, extrusion‐spheronization may be a promising path for future PBX formulation.

extrusion spheronization↗
DOE OSTI2024

Upcycling of Mixed Aluminum Alloy Shredder Scrap using Shear Processing

Conservation of critical materials is an increasing area of focus in the Unites States. In 2023, aluminum was added to the US Department of Energy Final Critical Materials List which has spurred public and private research into sustainable management of these resources. Additionally, efficiency in manufacturing and conservation of natural resources are growing concerns with targets to lower global carbon emissions, as primary aluminum alloy production is energy intensive, requiring 14 MWh of electricity plus 0.4 tonnes of CO2 per tonne of Al. Due to these factors, is essential that more sustainable manufacturing methods for aluminum alloys are developed going forward. To this end, much research is ongoing on the topic of more efficient utilization and recovery. However, most of this research still requires primary aluminum in the production process. Here, it will be attempted to bypass the use of primary aluminum and produce useful material recycled from 100% post-consumer scrap. Even considering recent developments in recycling of Al scrap, there is still a large amount of post-consumer scrap that is underutilized due to high impurity content, and that amount will increase significantly as more and more aluminum alloys are utilized in vehicles. This “scrap wave” is expected to cover 80% of the demand for automotive aluminum alloys by 2050 . A challenge to be addressed before the coming scrap wave can be fully utilized is that the tolerance of manufacturing techniques to impurities or off-spec alloy compositions must be increased. Particularly, in 5000-and 6000-series alloys (the most common wrought alloys in durable products), excess iron, copper, and silicon create brittle intermetallics during casting that remain in the extruded microstructure which limit the formability, ductility, and corrosion resistance of the alloy. Concerningly, many of the highest-volume post-consumer aluminum scrap streams such as automotive shredder scrap contain a mix of alloys including both wrought and cast alloys. Their compositions can vary widely depending on geography and the time of year. Because they are mixed, they often contain high content of multiple alloying elements such as Si and Cu in higher concentrations than are found in typical wrought alloys. They may also be contaminated with non-Al alloys from fasteners that get mixed in and often have high content of unwanted elements such as Fe. As a method for utilizing these underused scrap streams that are high in tramp elements, an emerging extrusion technology is being developed at the Pacific Northwest National Laboratory (PNNL) that aims to upcycle 100% post-consumer aluminum scrap directly into extruded components without the addition of primary aluminum . This new technology, called Shear Assisted Processing and Extrusion (ShAPE), is enabling a shift away from today’s recycling paradigm by reaching deeper into lower-value scrap streams, using shredder scrap as the extrusion billet material. Sometimes referred to as Twitch or Tweak, these scrap streams result from shredding and sorting of automobiles, building materials, appliances, and consumer goods. ShAPE combines the linear axis of conventional extrusion with a rotating extrusion die. This rotating die applies large strain to the material during extrusion, which breaks up large impurity-containing intermetallic particles, reducing their deleterious effects. This has been demonstrated for 6063 machining scrap spiked with excess Fe, and Twitch scrap high in Fe, Si and Cu where strength and ductility were retained for both feedstock compositions. Additionally, the extreme plastic deformation during ShAPE enables extrusion of billets with high Si that are too brittle for processing by conventional extrusion. By using 100% post-consumer shedder scrap as feedstock, ShAPE has the potential to slash embodied energy and carbon in extruded components by >80% compared to conventional extrusion of primary aluminum alloys.

Milligan, Brian K.↗
DOE OSTI2025

Creep suppression and fatigue in bio-based composites manufactured via conventional and large format additive manufacturing processes

The emergence of novel extrusion-based additive manufacturing (AM) processes has prompted the development of new thermoplastic composite feedstocks, and broadening sustainability initiatives have driven the development of bio-based and recyclable material for AM feedstocks. Poly(lactic acid) (PLA) with wood flour (WF) is one composite system that has been demonstrated in numerous AM applications, as well as traditional processing methods (i.e., compression and injection molding); however, there has been a need to understand how the variation in processing methodology impacts the material performance of these bio-based feedstocks from a fundamental perspective, with particular emphasis on creep for an extended application use-life. Herein, PLA/WF is explored as a feedstock material for large format additive manufacturing (LFAM) and the performance of additively manufactured materials is compared to those produced via more traditional processing methods. It is also demonstrated that the addition of WF decreases the material’s coefficient of thermal expansion (CTE) while increasing its Young’s modulus, susceptibility to water uptake, and creep fatigue resistance. Essentially, the addition of 20 wt% WF results in a 92 % decrease in rubbery regime CTE while simultaneously resulting in a 14 % increase in modulus, 190 % increase in water uptake, and a 31 % decrease in residual strain after cyclic creep tests. The processing method was also found to play a large role in the final part performance, with the printed material increasing the crystallinity by 183 % and 214 % compared to its compression and injection molded counterparts. Furthermore, the porosity of printed samples increased by two orders of magnitude compared to samples prepared via traditional processing methods.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Reduced-order CFD modeling of cryogenic hydrogen isotope extrusion for pellet fueling

This study presents a reduced-order model (ROM) for computational fluid dynamics (CFD) simulations of cryogenic hydrogen isotope extrusions, focusing on protium (H₂) and deuterium (D₂) piston extruders. Using a 2D axisymmetric ROM in ANSYS-Polyflow, significant computational savings were achieved (runtime reduced from 9∼24 h to 3∼5 min), with extrusion force discrepancies between the 2D ROM and 3D models being on the order of 1%. Parametric studies identified optimal cutoff shear rates in the viscosity model (0.01/s for H₂ and 0.001/s for D₂), providing recommendations for future simulations. Finally, a comprehensive comparison of ROM results with experimental data was performed across varying geometries, cryogenic materials, temperatures, extrusion lengths, and piston velocities. Predictions at low extrusion temperatures met the objective of providing quick and efficient solutions with an acceptable extrusion force error of approximately 10% or less, validating the effectiveness of the 2D ROM approach. However, at high temperatures closer to the triple point, extrusion force error grows, which necessitates developing an improved model that accounts for temperature effects, e.g. melting. Nevertheless, the findings still represent a significant improvement in efficiency of CFD modeling of cryogenic hydrogenic extrusion. The ROM framework can also be extended to tritium (T2) and screw extruders, which will ultimately provide a fast and effective tool for optimizing pellet injector design for ITER and future reactor systems.

Fan, Joy [ORNL] (ORCID:0000000229751735)↗
DOE OSTI2024

Advanced Design and 3D Printing Strategies With Alginate‐Nanoclay Nanocomposites: From Microstructure to Bioprinting

Nanocomposites made from alginate and nanoclay are extensively applied for diverse biomedical applications. However, the lack of a clear understanding of the interactions between alginate and nanoclay makes it difficult to rationally design the nanocomposites for different material extrusion-based 3D bioprinting strategies. Here, a combined analytical model is proposed to accurately predict the interaction mechanisms between alginate and nanoclay through small-angle neutron scattering. These mechanisms are summarized into a phase diagram that can guide the design of alginate-nanoclay nanocomposites for different bioprinting applications. The rheological properties of various nanocomposites are measured to validate the proposed interaction mechanisms at the macroscale. Accordingly, three representative extrusion-based bioprinting strategies are linked with the nanocomposite design and applied to freeform fabricate complex structures. In conclusion, a roadmap is summarized to bridge the gap between biomaterial design and bioprinting processes, enabling the rapid and rational selection of biomaterial formula based on available 3D printing methods, and vice versa.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Development of a Printable Prill Formulation Technique and Demonstration of Monomodal Prill Size on Compaction Density and Compressive Strength

Polymer-bonded explosive molding powder, or “prills,” are relied on for the fabrication of pressed high explosives since the 1950's. The wet granulation technique, also known as “slurry coating,” that is used to formulate prills, is a complex process that results in polydisperse and variable yields. This makes it difficult to study the mesoscale effect that prills have on the microstructure of a pressed article. The following study introduces a novel approach to energetic granulation that leverages techniques used in the additive manufacturing of paste-like energetic materials. This extrusion granulation, or prill printing technique, makes it possible to tailor the sizes and shapes of prills, allowing for their morphological influences to be studied in a controlled manner. The following work details the fabrication and characterization of four monomodal size lots of prills using an inert formulation (95 wt.% melamine, 5 wt.% polymer binder). Prills from each size lot were die-pressed using a fixed recipe to investigate how prill size impacts compaction density and therefore compressive strength. It was found that larger prills influence the pressing density by creating larger defects within the microstructure of a pressed article, resulting in a decrease in compressive strength.

direct ink write↗
DOE OSTI2024

Toward Multiscale, Multimaterial 3D Printing

Biological materials and organisms possess the fundamental ability to self-organize, through which different components are assembled from the molecular level up to hierarchical structures with superior mechanical properties and multifunctionalities. These complex composites inspire material scientists to design new engineered materials by integrating multiple ingredients and structures over a wide range. Additive manufacturing, also known as 3D printing, has advantages with respect to fabricating multiscale and multi-material structures. The need for multifunctional materials is driving 3D printing techniques toward arbitrary 3D architectures with the next level of complexity. In this paper, the aim is to highlight key features of those 3D printing techniques that can produce either multiscale or multimaterial structures, including innovations in printing methods, materials processing approaches, and hardware improvements. Several issues and challenges related to current methods are discussed. Ultimately, the authors also provide their perspective on how to realize the combination of multiscale and multimaterial capabilities in 3D printing processes and future directions based on emerging research.

36 MATERIALS SCIENCE↗
DOE OSTI2024

High Velocity Joining of Multi-material Stacks Containing 3rd Generation Advanced High-Strength Stainless Steel and Aluminum Extrusion and Casting (Abstract)

Advanced lightweight materials, including multi-phase steels, aluminum extrusions and aluminum castings, have increasingly replaced mild steel to meet original equipment manufacturer (OEM) demand for increased fuel economy and crash-safety requirements. Third Generation (Gen 3) AHSS provides a superior combination of strength and ductility for crash energy management components in the vehicle body-in-white (BIW). Aluminum extrusions are widely used for bumper, door rocker panel, cradle and battery frame applications. Aluminum castings are increasingly being used in electric vehicles to provide part consolidation, weight saving and increased driving range. Rocker panels are, for example, an important component of the battery electric vehicle (BEV) body structure. The rocker panel serves several purposes, including structural support, crash resistance, protection for the vehicle's underbody and battery tray, and contributing to the overall aesthetics. In order to reduce weight, rocker panels are usually constructed using outer panels consisting of 3rd generation advanced high strength steels (AHSS) and an inner multicell aluminum extrusion structure for energy absorption which protects the batteries in a crash event. It is well known, however, that these material combinations provide significant challenges for joining and are susceptible to liquid metal embrittlement and loss of strength. The overall goal is to find a solution that addresses these challenges in order to produce multi-material vehicle components with reduced weight and minimal galvanic and recyclability issues. The approach being proposed here is to utilize a novel high velocity (HiVe) riveting and clinching technique recently demonstrated by Pacific Northwest National Laboratory (PNNL) to join (2T/3T) sheets of aluminum alloys and steel. This process will not only address the aforementioned challenges but also help significantly reduce the joining cycle time. This work will also demonstrate use of HiVe assemblies to be retrofitted to existing body-shop robots thus having minimal impact to existing body shop operations.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermal images collected during large-scale 3D printing with Ingersoll MasterPrint

This data set contains images produced to test the performance of anomaly and fault detection methods in the context of additive manufacturing. Two print jobs were executed using the Ingersoll MasterPrint with the Model 30 Strangpresse extruder. The material used was Techmer compounded polylactic acid (PLA) with wood flour as a filler (80/20 PLA/WF by weight). The first print job consists of the 3D printing of a hexagonal cylinder with a two-bead wall. This print was sliced at a gantry velocity of 3000 millimeter per minute, and an extruder screw speed of 68.14 rotations per minute. This are considered the normal operating conditions. A second hexagonal cylinder was printed using a reduced extruder screw speed, 15% lower than under normal operating conditions. The images were collected with a Teledyne FLIR Lepton 3.5 infra-red camera, a small form factor radiometric long-wave infrared camera with a spectral range of 8 µm to 14 µm. Sensor resolution was 160x120 pixels, with a pixel size of 12 µm, a temperature range of -10 - 450°C, and an accuracy of +/- 10°C in its low gain configuration. Images in this data set were collected with cameras oriented at the printer nozzle. The nozzle camera setup consisted of two cameras located 12.5cm from the nozzle center. These were mounted directly to the print head, so that the camera positions relative to the print direction would remain constant as it rotated around its C-axis to follow the print path. One camera was placed ahead of the nozzle to capture the previous layer immediately before being covered by the new layer of material, while the second camera was placed behind the nozzle and captured the freshly extruded bead. Images are collecting during each phase of the print: (a) idle (i.e., no material deposited), (b) extrusion (i.e., to prime the extruder), and (c) printing (deposition of material to manufacture the hexagonal cylinder).

36 MATERIALS SCIENCE↗
DOE OSTI2024

Ink Casting and 3D‐Extrusion Printing of Yb 14 MnSb 11 for High‐Temperature Thermoelectric Material

Abstract Complex shapes are created from Yb 14 MnSb 11 , a high‐temperature thermoelectric Zintl phase, via a two‐step process: i) layer‐by‐layer 3D‐extrusion of ink containing partially‐reacted powders which are ball‐milled from a blend of Yb, MnSb, and Sb powders; ii) heat treatment to synthesize the ternary compound Yb 14 MnSb 11 and densify the extruded powders. A high phase purity for Yb 14 MnSb 11 (83–94%) is achieved in both cast and 3D‐extruded ink specimens via a solid‐state reaction between Yb, MnSb, and Yb 4 Sb 3 during reactive sintering. Pressure‐free sintering at temperatures of 1200–1400 °C densifies the powders to 82% relative density but can also induce the decomposition of the Yb 14 MnSb 11 phase due to Yb sublimation. A process window with optimized sintering temperature and time is identified, achieving both low porosity and high phase purity and reaching a maximum zT = 0.61 at 1000 °C, about half of the maximum zT value for bulk Yb 14 MnSb 11 made via conventional processes (pressure sintering of precursor powders). The present approach – direct ink writing of ball‐milled powders, combined with reactive sintering – is a scalable and affordable method to fabricate thermoelectric legs with intricate 3D shapes, for enhanced performances in high‐temperature thermoelectric applications.

Chen, Ming [Department of Materials Science &amp, ↗
DOE OSTI2025

Shear Assisted Processing and Extrusion of Magnesium Alloy Machining Chips

The Pacific Northwest National Laboratory (PNNL) utilized Shear Assisted Processing and Extrusion (ShAPE) to convert magnesium alloy machining chips directly into wrought material. PNNL fabricated 0.25” and 0.50” round rod from cold compacted briquettes pressed from dry-machined chips by Loukus Technologies. The alloy composition is proprietary and protected by a Materials Transfer Agreement (MTA) between PNNL and Loukus. Extrusions were fabricated using the ShAPE 2.0 machine, tooling, and process. PNNL is evaluating tensile properties per ASTM E8 and microstructure for grain size, texture, and porosity using Scanning Electron Microscopy (SEM) and Electron Backscatter Diffraction (EBSD). Tensile properties and microstructure results were not available at the time of writing this document. Extruded rods have also been sent to Loukus for evaluation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Synergistic torrefaction of plastic polymers and biomass

This study explores the synergistic torrefaction of biomass and plastics, aimed at enhancing bioenergy production and promoting a circular economy. By leveraging the unique properties of both materials, we investigated the thermochemical transformations occurring during the torrefaction process, from material preparation to the final characteristics of the torrefied product. The biomass used included corn stover (CS) and loblolly pine (LP), while various plastics were categorized from #1 to #7. Torrefaction was conducted at temperatures of 200, 225, and 250 °C, with subsequent extrusion of the torrefied materials and raw materials to produce composite filaments. The results show a consistent decrease in mass yield with increased torrefaction temperature, with notable variations among different biomass-plastic combinations. Co-torrefaction of biomass with polyvinyl chloride and polypropylene resulted in accelerated reaction kinetics, with an observed mass loss rate increase of 15 % at 250 °C compared to the expected rates for individual components. This synergy was quantified, indicating a 20.3 % increase in mass loss for the loblolly pine-polypropylene combination and 23.9 % for corn stover-polypropylene. In contrast, other plastics, including polyethylene terephthalate, high-density polyethylene, low-density polyethylene, polystyrene, and polycarbonate, did not exhibit significant synergistic effects. Mechanical testing indicated that the torrefaction process alters the strength and brittleness of the resulting materials, with implications for their application in bioenergy production and bio-renewable materials. Overall, this research highlights the potential of synergistic torrefaction as a viable strategy for co-processing biomass and plastics, paving the way for innovative solutions in waste management and renewable energy resource development.

09 - BIOMASS FUELS↗
DOE OSTI2025

Multiplexing core & sheath extrusion system development for additive manufacturing for inner-bead multi-material capability

Single-feed polymer extruders are widely used in large-format additive manufacturing (AM) systems; however, the increasing demand for multi-material functionality within a single part has driven significant innovation in this field. One approach involves robotic pick-and-place operations, while another explores mechanical switching of feed lines during extrusion. Although robotic pick-and-drop systems offer flexibility, they introduce longer layer times during material changes, which can negatively affect the structural integrity of the part. On the other hand, mechanical feed switching causes delays in material transitions, as the existing material must be flushed before the new material emerges from the nozzle. This poses particular challenges for smaller or more intricate parts. In this study we are developing a unique multiplexing extrusion system with core & sheath nozzle that combines two extruders via co-extrusion. This allows for a unique inside and outside inner-bead (i.e., within the same bead) multi-material capability. We believe that this technology will allow for combining neat and filled materials, ductile and stronger materials, and many other combinations to address the problems aforementioned above and disrupt the AM technology creating new opportunities and opening application areas.

Tekinalp, Halil [ORNL]↗
DOE OSTI2025

3D printable silicone compositions exhibiting high toughness and low durometer

3D printable silicones can be designed with varying crosslink density, network structures, and types of reinforcing additives. Within this design space, one may tailor the uncured material’s rheology and mechanical response to access a wide range of potential applications. However, printable, low modulus silicones, particularly those applicable to direct ink write, are underreported in published literature. To address the need for higher performance, low modulus silicones with demonstrated printability, a new set of ca. 20–50 Shore A hardness silicone elastomers exhibiting ca. 7 MPa ultimate tensile strength and ca. 400–1200% elongation at break is presented. Mechanical properties were analyzed, providing insight to the effects of formulation constituents on mechanical properties. Cyclic mechanical testing of the silicone formulations was also performed, and the energy loss and permanent set throughout cycling were determined. In conclusion, printed structures demonstrate the feasibility of these new silicones as durable frameworks for novel soft device applications.

36 MATERIALS SCIENCE↗