Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “lubricant technologies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Conversion of plastic waste into high-value lubricants: techno-economic analysis and life cycle assessment

Given the low recycling rate of plastic waste in the United States due to low economic incentives, it is of great interest to develop a technology to upgrade plastic waste with favorable economics. Plastic upcycling to valuable chemicals could ensure a circular economy for plastics and reduce the environmental burden caused by their end use cycle and disposal. A conceptual facility to convert 250 metric ton (MT) per day of plastic waste was modeled; the main product was a high-quality liquid (HQL) with a similar performance to polyalphaolefin (PAO) lubricants. The modeled process had a lubricant yield of up to 90% based on the experimental results at the laboratory scale. Techno-economic analysis (TEA) and life cycle assessment (LCA) were also performed to evaluate the process economics and its environmental impact. By using a mixture of colored and natural high-density polyethylene (HDPE), the production cost was in the range of 0.6–1.98 dollars per kg of lubricant, depending on the operating conditions. The life cycle emissions were in the range of 0.48–1.2 kg CO 2e kg Lub -1 showing, for the best case scenario, a 52% reduction relative to the emissions for petroleum lubricants, and a 74% reduction relative to the emissions for PAO lubricants. Finally, the impacts of the lubricant yield, the catalyst amount, and reaction time were evaluated, and their effect on the final production cost was discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Synthetic Lubricants Derived from Plastic Waste and their Tribological Performance

The energy efficiency, mechanical durability, and environmental compatibility of all moving machine components rely heavily on advanced lubricants for smooth and safe operation. Herein an alternative family of high-quality liquid (HQL) lubricants was derived by the catalytic conversion of pre- and post-consumer polyolefin waste. The plastic-derived lubricants performed comparably to synthetic base oils such as polyalphaolefins (PAOs), both with a wear scar volume (WSV) of 7.5×10 -5 mm -3 . HQLs also performed superior to petroleum-based lubricants such as Group III mineral oil with a WSV of 1.7×10 -4 mm -3 , showcasing a 44% reduction in wear. Furthermore, a synergistic reduction in friction and wear was observed when combining the upcycled plastic lubricant with synthetic oils. Additionally, life cycle and techno-economic analyses also showed this process to be energetically efficient and economically feasible. This novel technology offers a cost-effective opportunity to reduce the harmful environmental impact of plastic waste on our planet and to save energy through reduction of friction and wear-related degradations in transportation applications akin to synthetic oils.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Supercritical water co-liquefaction of LLDPE and PP into oil: properties and synergy

The major plastic wastes are always mixtures, which are difficult to separate to treat in practice. Because of some possible cross-reactions, the degradation behaviors of plastics could not be mathematically represented by a simple addition of each polymer according to their proportions. This work examines supercritical water (scH 2 O) to liquefy poly-ethylene and poly-propylene mixtures into an oil with special interest in the oil quality and positive effect. Additionally, linear low-density polyethylene (LLDPE) and polypropylene (PP) were chosen as parent materials because of their high proportions in plastic wastes. The results show that a high conversion rate of around 99.75% was achieved with as high as 90.7 wt% oil yield without additional catalysts or hydrogen. The scH 2 O co-liquefaction of the LLDPE/PP mixture was different from that of the single polymer along with an improvement in the oil yield. Cyclic hydrocarbon ( i.e. , cyclic) generation was promoted while the production of paraffins was hindered in scH 2 O co-liquefaction using a mixture of LLDPE/PP. TGA reveals that the scH 2 O co-liquefaction of LLDPE/PP mixtures generated more diesel and lubricant oils and less gasoline and (jet fuel + light diesel) oils, thus slightly lowering the oil quality. Overall, the supercritical fluid technology was a powerful and promising means to liquefy mixed plastic wastes into oil at a high conversion rate free of catalysts or hydrogen.

42 ENGINEERING↗
DOE OSTI2024

Advanced silver sheathed 2212/Ag wire for high field magnets

Commercial High Temperature Superconductors (HTS) are all tape shaped (widths > 10 times thickness), because achieving useful current densities required them to be processed into this form, even though this also makes it more problematic to use them in some important coil types. Our product is based on 2212 (Bi2Sr2CaCu2O8) and it is the only HTS that can be processed into high current density wire forms that are similar to proven low temperature superconductors (LTS), while surpassing them in field generating and operating temperature capability. Required now are higher current density, lower cost and longer length 2212 wires to enable broad utilization where HTS tape usage is problematic. In Phase II we developed vital cost-lowering process technology elements and we test-processed longer wires with the standard commercial design as baseline and benchmark for our lower cost, higher quality and longer piece length wire advances. By initial application of Jc-boosting wire features, these wires exhibited significant performance increases. This Phase IIA program has now developed and qualified these technologies for lower cost, higher quality and longer piece length manufacturing in combination with current density-boosting wire features, paving the way to manufacturing capability that is essential for cost-effective commercial utilization of 2212 wire. Technical areas included automated, high uniformity powder packing, advanced drawing, annealing, lubricant cleaning and filament bundling, followed by integration of higher current density wire features and process variations.

17 WIND ENERGY↗
DOE OSTI2024

Energy and nutrient recovery from municipal and industrial waste and wastewater—a perspective

This publication highlights the latest advancements in the field of energy and nutrient recovery from organics rich municipal and industrial waste and wastewater. Energy and carbon rich waste streams are multifaceted, including municipal solid waste, industrial waste, agricultural by-products and residues, beached or residual seaweed biomass from post-harvest processing, and food waste, and are valuable resources to overcome current limitations with sustainable feedstock supply chains for biorefining approaches. The emphasis will be on the most recent scientific progress in the area, including the development of new and innovative technologies, such as microbial processes and the role of biofilms for the degradation of organic pollutants in wastewater, as well as the production of biofuels and value-added products from organic waste and wastewater streams. The carboxylate platform, which employs microbiomes to produce mixed carboxylic acids through methane-arrested anaerobic digestion, is the focus as a new conversion technology. Nutrient recycling from conventional waste streams such as wastewater and digestate, and the energetic valorization of such streams will also be discussed. The selected technologies significantly contribute to advanced waste and wastewater treatment and support the recovery and utilization of carboxylic acids as the basis to produce many useful and valuable products, including food and feed preservatives, human and animal health supplements, solvents, plasticizers, lubricants, and even biofuels such as sustainable aviation fuel.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Developing a Facile Technology for Converting Domestic US Coal into High-Value Graphene

Universal Matter Ltd. was formed in July 2019 to scale-up and commercialize a breakthrough process, Flash Joule Heating (FJH), to transform different coal grades, into high-quality graphene. This graphene is made using a high-voltage electric discharge that brings the carbon source to temperatures higher than 3,000 K in less than 10 milliseconds. The short burst of electricity breaks all chemical bonds in the feedstock and reorders the carbon atoms into exceptionally thin layers of a special type of graphene, at an estimated $100 per ton in electricity cost. This process is capable of producing 1-5 layer-thick high-quality graphene (with defects of <0.05% and purity of >99%) in a green, practical, and cost-effective process. The graphene produced in the FJH process is a very special kind of graphene called “turbostratic graphene” (TG). TG offers superior physical properties compared to other graphene structures on a similar weight basis. Unlike graphene made from graphite using traditional techniques, the graphene layers in TG stack in an irregular pattern that allows the graphene powder to be exfoliated more easily and blend more evenly within other materials. The TG produced using our FJH technology is the most economical graphene product that opens up significant large volume markets for end-use applications; it would allow the use of TG made from coal for commercial applications in several market segments including energy storage, sensors, hyper-lubricants, reinforced plastics, and building materials such as concrete.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

Achieving clean production with nanostructured coated milling tools dry machining low carbon steel

The advancement of clean production using nanostructured materials in subtractive manufacturing processes has focused on replacing the use of liquid lubrication with solid lubricants coated to conventional cutting tools machining low carbon steel (~ 0.2 wt. % carbon). However, little is known about the wear mechanisms that dominate such tools when coated with functional graded nanostructured coatings. The present study follows an international standard for characterizing such wear (ISO 8688) but uses advanced measurement techniques such as x-ray fluorescence technology to measure the diffusion of chemical species from tool to workpiece and vice versa, that contributes to tool wear with the view to enhance the principles of cleaner production. The results show that when commercially-available tools coated with the appropriate functionally graded industrial coating, diffusion does not take place and creates an effective chemical barrier during machining. The experimental methods used in the study include machining workpieces using a CNC milling machine, tachometer for measuring spindle speed, dynamometer for measuring cutting forces, infra-red camera for measuring cutting temperatures, chemical species diffusion wear using x-ray florescence detector, and an optical microscope for measuring tool wear. Coupled with the physical measurement of wear, it is concluded that mechanical wear dominates the milling of a low carbon steel and that thermal properties of the coatings do not correlate with such wear. It is also concluded that flank wear as a function of volume of workpiece removed and machining duration (machining index) is a sound method for assessing the transition of the stages of wear during clean machining operations. The present study not only has implication for the design of better cutting tools, but also advances dry machining processes that eliminate the use of liquid lubricants making subtractive production processes cleaner. The main conclusions drawn from this study show that coated tools have a longer life under dry conditions compared to uncoated tools and that there is no correlation between coating properties and tool wear. In conclusion, diffusion of chemical species into the cut chips did not occur because of the lack of thermally induced chemical wear of the cutting tool and that wear is caused by the gradual erosion of the flank face due to the chip abrading the cutting tool.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Improving Marine Energy Production Through Commercialization of a Low Cost, Drag-Reducing Slippery Coating (CRADA 679 Abstract)

Marine energy capture systems offer great promise for providing clean energy, but they operate in a challenging and dynamic environment and must be optimized to the highest extent possible. Computational studies predict that drag reduction on marine energy and blue economy systems will result in meaningful improvements in energy efficiency. Based on extensive coating experience, PNNL is proposing to bring to market a new drag-reducing coating called Superhydrophobic Lubricant-Infused Drag-Efficient Coating – SLIDE-Coat. PNNL has a deep knowledge base regarding this class of slippery coatings, and we have a group of enthusiastic industry partners who have committed to partnering, conducting field testing, and providing well over 50% cost share. In addition to validating the technology, the team will create a commercialization roadmap to ensure the commercial success of the technology after the government-sponsored two-year program is complete. The main technical goal is to design, manufacture, and experimentally validate a new coating that can reduce hydrodynamic skin friction drag by 20%. The main commercialization goal is to develop a roadmap that identifies activities needed to complete SLIDE-Coat’s development after the conclusion of this project. Year 1 will focus on adaptation and modification of the existing SLIC coating system to optimize drag reduction and assessment and quantification of drag reduction on relevant materials in a laboratory setting. Year 2 will focus on optimizing and demonstrating drag reduction with preferred coatings. The manufacturability, ease of application, adhesion to relevant surfaces, and consistency will be assessed. Quantification of drag reduction on prototype materials in a relevant marine field setting will be executed.

16 TIDAL AND WAVE POWER↗
DOE OSTI2023

Neutron Imaging of Al6061 Prepared by Solid-State Friction Stir Additive Manufacturing

Solid-state Friction Stir Additive Manufacturing has recently gained attention as a result of its capacity to fabricate large-scale parts while preserving the mechanical properties of the feedstock material. However, the correlation between the quality of layer-by-layer bonding of the deposited metal and processing parameters has remained unknown. Neutron imaging techniques, with 90% total transmission per cm, are employed for Al6061 parts fabricated by MELD ® Technology as a non-destructive evaluation approach for the first time to investigate the layer-by-layer structure of a stadium-shaped ingot in different sections. The post-processed results show the fabricated parts with an optimized set of processing parameters are void-free. However, the hydrocarbon-based feedstock lubricant segregates between the layers, which consequently may lead to non-uniform weaker mechanical properties along the build direction and stimulate crack initiation during mechanical loading. The tensile test results show 14% lower strain-to-failure values in alleged contaminated areas in transmission imaging results. Additionally, layer bonding is significantly impacted by hot-on-hot and hot-on-cold layer deposition schemes, especially for larger layer thicknesses.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Additively Manufactured Compliant Hybrid Gas Thrust Bearing for Supercritical Carbon Dioxide Turbomachinery: Design and Proof of Concept Testing

The following paper presents a new type of gas lubricated thrust bearing that utilizes additive manufacturing or also known as direct metal laser melting (DMLM) to fabricate the bearing. The motivation for the new bearing concept is derived from the need for highly efficient supercritical carbon dioxide (sCO2) turbomachinery in the mega-watt power range. The paper provides a review of existing gas thrust-bearing technology, outlines the need for the new DMLM concept, and discusses proof-of-concept testing results. The new concept combines hydrostatic pressurization with individual tilting pads that are flexibly mounted using hermetic squeeze film dampers (HSFD) in the bearing-pad support. This paper describes the thrust-bearing concept and discusses the final design approach. Proof-of-concept testing in air for a 6.8 in. (173 mm) outer diameter thrust gas bearing was performed; with thrust loading, up to 1500 lbs (6.67 kN) and a thrust runner speed of 10krpm (91 m/s tip speed). The experiments were performed with a bent shaft resulting in thrust runner axial vibration magnitudes of 2.9 mils (74 μm) p-p and dynamic thrust loads of 270 lbs (1.2 kN) p-p. In addition, force deflection characteristics and stiffness coefficients of the bearing system are presented for an inlet hydrostatic pressure of 380 psi (2.62 MPa). Results at 10 krpm show that the pad support architecture was able to sustain high levels of dynamic misalignment equaling 6 times the nominal film clearance while demonstrating a unit load-carrying capacity of 55 psi (0.34 Mpa). Gas-film force deflection tests portrayed nonlinear behavior like a hardening spring, while the bearing pad support stiffness was measured to be linear and independent of gas film thickness.

Engineering↗
DOE OSTI2022

Analysis of an Elasto-Hydrodynamic Seal by Using the Reynolds Equation

This paper reports numerical studies of an Elasto-Hydrodynamic (EHD) seal, which is being developed for supercritical CO2 (sCO2) turbomachinery applications. Current sCO2 turbomachinery suffers from high leakage rates, which is creating a major roadblock to the full realization of sCO2 power technology. The high leakage rates not only penalize the efficiencies but also create environmental concerns due to greenhouse effects caused by the increased CO2 discharge to the atmosphere. The proposed EHD seal needs to work at elevated pressures (10–35 MPa) and temperatures (350–700 °C) with low leakage and minimal wear. The unique mechanism of the EHD seal provides a self-regulated constriction effect to restrict the flow without substantial material contact, thereby minimizing leakage and wear. This work utilizes a physics-based modeling approach. The flow through the gradually narrowing seal clearance is modeled by the well-known Reynolds equation in EHD lubrication theory, while the deformation of the seal is modeled by using the governing equations of three-dimensional solid mechanics. As for the solution methodology, COMSOL’s Thin-Film Flow and Solid Mechanics modules were employed with their powerful capabilities. The numerical results were presented and discussed. It was observed that the Reynolds equation fully coupled with the surface deformation was able to successfully capture the constriction effect. The maximum and minimum leakages were calculated to be 2.25 g/s and 0.1 g/s at P = 5.5 MPa and P = 11 MPa for the design seal, respectively. It was interesting to observe that the seal leakage followed a quadratic trend with increasing pressure differential, which can become advantageous for high-pressure applications such as sCO2 power generation technology.

42 ENGINEERING↗
DOE OSTI2025

High-Temperature Active Magnetic Bearing Development for Supercritical CO 2 Machinery Applications

Hermetic machinery utilizing gas bearings for MW-scale supercritical CO 2 (sCO 2 ) machinery applications can have significantly lower power loss and enable improved cycle efficiency compared to conventional machinery with oil-lubricated bearings. Active magnetic bearings (AMBs) are another option anticipated to have similar power loss and load capacity to gas bearings as well as offering larger mechanical tolerances, the ability to tune properties, and high reliability due to lack of mechanical wear. AMBs also have proven commercial experience at MW-scale, though environments for high-temperature sCO 2 power cycle machinery conditions are novel. Besides the potential impact of AMBs for sCO 2 turbomachinery, the technology also offers promising benefits for steam and gas turbines for power generation, compressors and expanders for industrial heat and power, and in other oil and gas and space applications. The goals of this project were to conceptual design an AMB and perform material testing. Conceptual designs for radial and thrust AMBs were produced based on a hermetically-sealed sCO 2 machinery waste-heat recovery (WHR) application for sizing and loads, and choosing a target design temperature of 540°C useful for high-temperature sCO 2 turbines for concentrating solar power (CSP) applications. Conceptual designs were initially developed for multiple radial and thrust AMBs with spreadsheet-based calculations before selecting one of each to develop further using higher-fidelity design methods for magnetic and structural performance. It was found that the radial AMB at 540°C was feasible, but the thrust AMB needed to be limited to 315°C for high-speed operation. The decision for a reduced-temperature thrust AMB was the result of several significant conclusions: 1) Hiperco 50A, originally chosen for good magnetic performance at high temperature, had insufficient strength for high-speed operation, so it was replaced with 17-4 PH. 2) The reduced magnetic performance from 17-4 PH yielded a larger bearing size, reducing the strength margin. 3) This ultimately led to a creative design implementing a more-compact E-core topology, compared to the original (conventional) C-core, and an integral shaft-disk with Hirth joint connection. These conceptual designs are unique for the size and temperature in CO 2 , relevant for MW-scale CSP applications. Long term, high temperature test data was generated for several materials, filling a void in the current body of literature. Corrosion and magnetic performance measurements were produced for PM materials (Alnico 5-7C, Alnico 9C, and SmCo) with and without nickel-coating for environments of high-temperature CO 2 up to 550°C at atmospheric pressure and 450°C at 103 bar for up to 6,000 hours. Corrosion measurements were also produced for Hiperco 50, a SM material relevant for AMB laminations, with and without C5 coating. Comparisons were also made for 450°C and 550°C, atmospheric pressure air exposures up to 5,000 hours. Results generally show that coatings can be effective at improving oxidation resistance of the bare materials, and Alnicos generally outperformed SmCo after high-temperature exposure. In addition to technical feasibility demonstrated by the design, economic feasibility was demonstrated by updating the TEA from the reference machine, re-evaluating it with CAPEX and OPEX to reflect estimated changes from process-lubricated bearings to AMBs. AMBs were shown to be comparable in performance to process-lubricated bearings, still showing a notable improvement over conventional machinery architecture with oil-lubricated bearings.

42 ENGINEERING↗
DOE OSTI2020

Towards developing robust solid lubricant operable in multifarious environments

Abstract Conventional solid lubricants such as MoS 2 , graphite, or diamond-like carbon films demonstrate excellent tribological performance but only in specific environments due to their inherent materials properties. This limitation prohibits using these solid lubricants in environments that change dynamically. This study presents the results of a novel solid lubricant that was developed using a combination of solution-processed 2D-molybdenum disulfide and graphene-oxide (GO) that can be deposited on to stainless steel substrates using a simple spray-coating technique and show exceptional performance in multifarious environments namely, ambient (humid) atmosphere, dry nitrogen, and vacuum. The tribological performance of the coatings was evaluated using a ball-on-disc sliding test and demonstrated an excellent wear/friction performance in all environments and coating survived even after 44 km of linear sliding. Transmission electron microscopy and Raman spectroscopy analysis of the tribolayers suggested in-operando friction-induced re-orientation of MoS 2 layers that were protected by GO layers and, an absence of MoO x peaks indicate a strong resistance to intercalation with moisture and oxygen. The simplicity and robustness of the hybrid MoS 2 –GO solid lubricant in mitigating wear-friction behavior of steel-on-steel tribopair in a multifarious environment is a game-changing and is promising for various applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Tritium Producing Burnable Absorber Rod (TPBAR) Cutterhead Test Report

The Tritium Extraction Facility (TEF) Target Rod Preparation (TRP) Tritium Producing Burnable Absorber Rod (TPBAR) Cutterhead is a specialized remote tubing cutter used to breach TPBARs (approximately 0.381 inch outside diameter x 0.336 inch inside diameter 316 stainless steel tubing). The cutterhead was originally designed by an external engineering firm - RTS Wright Industries. The bearing housing and drive plate, the main drive components, are designed to be fabricated from Nitronic 60, an anti-galling stainless steel, and coated with Dicronite® (Tungsten Disulfide) lubricating coating. These parts have galled after a limited number of cycles, damaging the fine 3.25-32 UN threads which drive the system. In some cases, destructive sectioning is required to remove the failed parts from the cutterhead. Cutterheads have been fabricated by multiple machine shops, with some cutterheads failing very quickly and some lasting more than 1,000 cuts. In 2019, Emery Corporation, now Toner Machining Technologies (TMT) was contracted to fabricate four (4) new complete sets of cutterheads. The newly fabricated cutterheads have not been able to pass the required acceptance test without the bearing housing and drive plate threads galling. TMT has tried multiple sets of Nitronic 60 bearing housing and drive plates; all have galled after less than 10 cuts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Pseudo-Hot-Isostatic Pressing (P-HIP)

Researchers at Los Alamos National Laboratory developed a technology to produce high performance ceramic or metal with a combination of major key properties such as versatile-complicated shape, high density, uniform density distribution, and minimal amounts of starting material. The novel pseudo-hot-isostatic-pressing (P-HIP) uses graphite or boron nitride flakes as the stress transmission media to transmit stress instead of the conventional solid graphite punch. The graphite and boron nitride flakes are solid lubricants and can slide among one another to re-distribute the stress from high stress concentration area to the low stress concentration areas, resulting in a self-stress-relief action. This innovative P-HIP enables the manufacturing of complicated shapes with near-net-shape capability while minimizing the energy used and reducing waste. This is a revolutionary breakthrough to the ceramics and powder metallurgy industries.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Improved Value of the Gasoline and Fuel Oil Co-Product Fractions Generated by the PNNL/LanzaTech Alcohol-to-Jet Process (Final Report)

The BETO-funded PNNL collaboration with LanzaTech, Inc. utilizes patented technology to address the need for low aromatic jet fuel blendstocks. The PNNL/LanzaTech alcohol-to-jet (ATJ) process converts ethanol from LanzaTech’s syngas fermentation process to jet-range isoparaffins. The aim of this Cooperative Research Development Agreement (CRADA) project was to improve the commercial viability of the LanzaTech/ PNNL ATJ process by developing two new co-product options. Two Focus Areas (FA) were explored: FA1) Increasing the RON of the lighter-than-jet gasoline fraction above 98; and FA2) Creating a synthetic lubricant base oil from the heavier-than-jet fraction. For FA 1, multiple processing approaches were evaluated, and RONs ranging from 96-100 were obtained, each comprising different processing costs. The most cost effective approach identified was a single-step process and yielded a liquid product of 97. Thus, additional development is required to obtain a RON > 98. We will continue work on this focus area with separate Direct Funding Opportunity (DFO) funding within the DOE-BETO Co-Optima Consortium (expected to begin Q2-FY21). Experimental work will focus on i) increasing single pass conversion to > 50%, and ii) obtaining a > 98 RON product. Technoeconomic analysis performed in this project suggests cost competitiveness provided these technical targets can be met. For FA2, multiple approaches were evaluated for increasing the viscosity index (VI) of the heavier-than-jet fraction to at least 120 in order to meet ASTM specifications for a Group III Base Oil (ASTM D6074). All other ASTM specifications are already met. A viscosity index of 115 was obtained, and with minimal undesirable cracking products. We believe a VI of 115 is about the highest possible from a catalytic approach, per review of the patent literature. In order to further increase the VI to > 120 we believe additives and/or liquid-liquid extraction is required. TEA performed earlier in the project suggests cost competitiveness with market prices assuming cracking byproducts are kept < 10 wt.%. If TEA updated with this additional processing still projects economic feasibility next steps could be taken in a subsequent effort.

02 PETROLEUM↗
DOE OSTI2024

Colloquium : Sliding and pinning in structurally lubric 2D material interfaces

A plethora of two-dimensional (2D) materials have been introduced in physics and engineering in the past two decades. Their robust, membranelike sheets permit (mostly require) deposition, giving rise to solid-solid dry interfaces whose mobility, pinning, and general tribological properties under shear stress are currently being understood and controlled, both experimentally and theoretically. Here, in this Colloquium simulated case studies of twisted graphene systems are used as a prototype workhorse tool to demonstrate and discuss the general picture of 2D material interface sliding. First highlighted is the crucial mechanical difference, often overlooked, between small and large incommensurabilities, which corresponds to, for example, small and large twist angles in graphene interfaces. In both cases, focusing on flat, structurally lubric or “superlubric” geometries, the generally separate scalings with the area of static friction in pinned states and of kinetic friction during sliding are elucidated and reviewed, tangled as they are with the effects of velocity, temperature, load, and defects. The roles of island boundaries and elasticity are also discussed, and compared when possible to results in the literature for systems other than graphene. It is proposed that the resulting picture of pinning and sliding should be applicable to interfaces in generic 2D materials that are of importance for the physics and technology of existing and future bilayer and multilayer systems.

2-dimensional systems↗
DOE OSTI2025

Bridging microscopic dynamics and rheology in the yielding of charged colloidal suspensions

The yielding of soft materials is critical to many natural and industrial processes, yet experimental insights into microscopic aspects of yielding are limited. This study combines angle X-ray scattering, X-ray photon correlation spectroscopy, and in situ rheology (Rheo-SAXS-XPCS) with fast lubrication dynamics simulations to examine how interparticle interactions influence yielding in charged colloidal suspensions. By tuning attraction through salt addition, we compare repulsive and attractive systems under deformation. Repulsive suspensions yield uniformly with Andrade-like creep and minimal structural change. In contrast, attractive suspensions show complex behaviors, including shear banding, delayed yielding, and resolidification, governed by transient dynamics at shear band interfaces. These results directly link microscopic particle dynamics to macroscopic flow and demonstrate how interaction potentials control rheological behavior. This work offers a framework for designing soft materials with tailored properties for applications in coatings, food processing, drug delivery, and other technologies requiring precise mechanical control.

Molecular Dynamics Simulation↗