Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “loss reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Additively Manufactured Copper Windings with Hilbert Structure

In this paper, finite element method simulations and frequency analysis of additively manufactured windings with a Hilbert–cross section pattern were performed over a wide frequency range. The current density distributions for the proposed winding conductor and for a square-wire winding conductor at selected frequencies were compared. An approximately 25% winding loss reduction at higher frequencies and an approximately 5% increase at low frequencies were observed for the analyzed Hilbert structure.

Wojda, Rafal↗
DOE OSTI2022

Allocating Reserves in Active Distribution Systems for Tertiary Frequency Regulation

This paper proposes a cooperative game theory-based approach for reserve optimization to enable distributed energy resources (DERs) participate in tertiary frequency regulation. Tertiary frequency regulation schemes ensure that reserve requirements of primary and secondary frequency regulation are fulfilled with a minimum cost. While the available reserve from a single distribution system may not suffice tertiary frequency regulation, stacked reserve from several distribution systems can enable them participate in tertiary frequency regulation at scale. In this paper, a two-stage strategy is proposed to effectively and precisely allocate spinning reserve requirement from each DER in distribution systems. In the first stage, two types of characteristic functions are computed: worthiness index (WI) and power loss reduction (PLR). In the second stage, the equivalent Shapley values are computed based on the characteristic functions, which are used to determine distribution factors for reserve allocation among DERs. The effectiveness of the proposed method for allocating reserves among DERs is demonstrated through several case studies on modified versions of the IEEE 13-node and 33-node distribution systems.

Gautam, Mukesh↗
DOE OSTI2021

Assessment of Electrode Contamination Mitigation at 0.5 MA Scale

The Z Machine at Sandia National Laboratories uses current pulses with peaks up to 27 MA to drive target implosions and generate high energy density conditions of interest for stockpile stewardship programs pertinent to the NNSA program portfolio . Physical processes in the region near the Z Machine target create electrode plasmas which seed parasitic current loss that reduce the performance and output of a Z experiment. Electrode surface contaminants (hydrogen, water, hydrocarbons) are thought to be the primary constituent of electrode plasmas which contribute to loss mechanisms. The Sandia team explore d in situ heating and plasma discharge techniques by integrating requisite infrastructure into Sandia's Mykonos LTD accelerator, addressing potential impacts to accelerator operation, and reporting on the impact of these techniques on electrode plasma formation and shot performance. The in situ discharge cleaning utilizes the electrodes of the accelerator to excite an argon-oxygen plasma to sputter and chemically react contaminants from electrode surfaces. Insulating breaks are required to isolate the plasma in electrode regions where loss processes are most likely to occur. The shots on Mykonos validate that these breaks do not perturb experiment performance, reducing the uncertainty on the largest unknown about the in situ cleaning system. Preliminary observations with electrical and optical diagnostics suggest that electrode plasma formation is delayed, and overall inventory has been substantively reduced. In situ heating embeds cartridge heaters into accelerator electrodes and employs a thermal bakeout to rapidly desorb contaminants from electrode surfaces. For the first time, additively manufactured (AM) electrode assemblies were used on a low impedance accelerator to integrate cooling channels and manage thermal gradients. Challenges with poor supplier fabrication to specifications, load alignment, thermal expansion and hardware movement and warpage appears to have introduced large variability in observed loss, though, preventing strong assertions of loss reduction via in situ heating. At this time, an in situ discharge cleaning process offers the lowest risk path to reduce electrode contaminant inventories on Z, though we recommend continuing to develop both approaches. Additional engineering and testing are required to improve the implementation of both systems. .

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Feasibility of using crystal channeling for the beam loss mitigation in Slow Extraction at 8GeV

The mitigation of the beam losses in slow extraction is becoming more and more demanding in accelerator applications for HEP as the beam power is gradually increasing. The successful demonstration of using the proton beam channeling at 450GeV to deflect the beam away from the extraction septa opens the new levels of improving the slow extraction efficiency. It is yet to be demonstrated that this method is still effective at low and medium proton beam energies. Here we present the promising results of the recent computer simulation studies of the septum shadowing at 8GeV for the Mu2e project slow extraction at Fermilab. Depending on the beam parameters the beam loss reduction is shown to be achievable in the range of 1/3 to factor of 3.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

Invertebrate and Plant Community Diversity of an Illinois Corn–Soybean Field with Integrated Shrub Willow Bioenergy Buffers

Perennial bioenergy crop production within intensively managed agricultural landscapes has the potential to improve the sustainability, resiliency, and diversity of these landscapes. Perennial crops are ideal because of their high production potential on marginal lands relative to grain crops (e.g., corn and soybean) and their ability to provide additional ecosystem service benefits. When agricultural landscapes are designed to target specific services, determining the non-targeted services of perennial bioenergy crops can further promote their adoption. This 3-year study addresses this proposition by evaluating the canopy invertebrates and understory plant (non-target crop) communities using bee bowls and point measurement of ground coverage, respectively, within a grain field integrated with shrub willow buffer systems designed for nutrient loss reduction. Greater plant diversity and richness were observed under willow than under grain, resembling that of the surrounding riparian community with more perennial, native species. However, the same relationship did not hold true for invertebrates, with seasonality having a significant influence resulting in similar communities observed in willow and grain plots. The presence of unique plant and invertebrate species in both willow and grain crops as well as foraging pollinators on both crop and non-target crop species highlights the importance of habitat heterogeneity for supporting biodiversity and the potential benefits of buffer bioenergy landscape designs.

09 BIOMASS FUELS↗
NASA NTRS1976

NASA thermionic-conversion program

Current out-of-core emphases allow converter material and design freedoms previously prohibited by in-core nucleonic and geometric restrictions. As a result, potential improvements indicate possibilities for severalfold increases in efficiencies. The new TEC-ART program concentrated initially on low-work function collectors and interelectrode-loss reduction and revealed much in a short time. This new emission capability coupled with improved collectors that maintain performance with emitter-vapor deposit accumulations are requisites for efficient, enduring thermionic converters.

Morris, J. F.↗
NASA NTRS1976

NASA thermionic-conversion program

The NASA applied research and technology (ART) program for thermionic energy conversion (TEC) is progressing effectively. Current out-of-core emphases allow converter material and design freedoms previously prohibited by in-core nucleonic and geometric restrictions. As a result, potential improvements indicate possibilities for severalfold increases in efficiencies. The new TEC-ART program concentrated initially on low-work-function collectors and interelectrode-loss reduction and revealed much in a short time. For example, arc-drop studies verified the necessity of stable emitters that operate well with little or no adsorbed cesium. This new emission capability coupled with improved collectors that maintain performance with emitter-vapor deposit accumulations are requisites for efficient, enduring thermionic converters. The accomplishments and contributors in these areas are discussed.

Morris, J. F.↗
NASA NTRS1978

Experimental studies on the influence of the degree of turbulence and of a turbulence thread on the compressible subsonic flow through flat compressor cascades

The measurements revealed that at low Reynolds numbers the profile loss is considerably reduced both by the increased degree of turbulence and by a turbulence thread, while it is somewhat increased at high Reynolds numbers, and that a profile loss reduction is connected with an increase in deflection and in pressure shift. The turbulence generator is most effective on the one hand in the middle of the operating range of the cascades, and on the other at very high Mach numbers together with a large angle of incidence.

Barsun, K.↗
NASA NTRS1980

Integrated optic waveguide devices

Integrated optic waveguide circuits with a phase bias and modulator on the same chip were designed, fabricated, and tested for use in a fiber-optic rotation sensor (gyro) under development. Single mode fiber-optic pigtails were permanently coupled to the four ports of the chip. The switch format was based on coherent coupling between waveguides formed in Z-cut LiNbO3. The control of the coupling was achieved by electro-optically varying the phase propagation constants of each guide. Fiber-to-chip interfacing required the development of appropriate fixturing and manipulation techniques to achieve the close tolerance needed for high coupling efficiency between a fiber with an approximately 5 micron m core and a channel guide with a roughly 2 micron m by 5 micron m cross section. Switch and chip performance at 0.85 micron m is discussed as well as potential improvements related to insertion loss reduction, switching voltages, and suppression of Li2O out-diffusion.

Ramer, O. G.↗
NASA NTRS1985

High-efficiency device research

Progress on research in high-efficiency silicon solar cells is presented. Topics addressed include: recombination measurement techniques, doped crystals, minority carrier transport, oxygen process in solar cells, solar cell models, loss mechanics in solar cells, high-efficiency metal insulators, dendritic web cells, and surface and bulk loss reduction by low-energy hydrogen doping.

Burger, D. R.↗
NASA NTRS1989

Analysis and test of insulated components for rotary engine

The direct-injection stratified-charge (DISC) rotary engine, while attractive for aviation applications due to its light weight, multifuel capability, and potentially low fuel consumption, has until now required a bulky and heavy liquid-cooling system. NASA-Lewis has undertaken the development of a cooling system-obviating, thermodynamically superior adiabatic rotary engine employing state-of-the-art thermal barrier coatings to thermally insulate engine components. The thermal barrier coating material for the cast aluminum, stainless steel, and ductile cast iron components was plasma-sprayed zirconia. DISC engine tests indicate effective thermal barrier-based heat loss reduction, but call for superior coefficient-of-thermal-expansion matching of materials and better tribological properties in the coatings used.

Badgley, Patrick R.↗
NASA NTRS1990

Longitudinal variation of mid-latitude hiss from six long duration balloon flights

The longitudinal variation of midlatitude hiss as measured on six balloons at latitudes of 35-55 deg S, shows a significant minimum at 70-80 deg E, about 1000 km east of the geomagnetic conjugate of the Soviet transmitter UMS (17.1 kHz). It is suggested that the well documented pitch-angle diffusion induced by the UMS signal removes the ability of the trapped electrons to maintain the amplification of the hiss to at least the reflection and reducting losses (about 20 dB) at the ends of the echoing ducted path. The eastward shift of the minimum from the conjugate of UMS is primarily caused by the time taken by the eastward-drifting electrons to recover this ability, though the effect is enhanced by the east-west asymmetry in the propagation of hiss under the ionosphere.

Dowden, R. L.↗
NASA NTRS2001

Cryogenic Propellant Long-Term Storage With Zero Boil-Off

Significant boil-off losses from cryogenic propellant storage systems in long-duration space mission applications result in additional propellant and larger tanks. The potential propellant mass loss reductions with the Zero Boil-off (ZBO) concept are substantial; therefore, further exploration through technology programs has been initiated within NASA. A large-scale demonstration of the ZBO concept has been devised utilizing the Marshall Space Flight Center (MSFC) Multipurpose Hydrogen Test Bed (MHTB) along with a cryo-cooler unit. The ZBO concept consists of an active cryo-cooling system integrated with traditional passive thermal insulation. The cryo-cooler is interfaced with the MHTB and spraybar recirculation/mixer system in a manner that enables thermal energy removal at a rate that equals the total tank heat leak. The liquid hydrogen (LH2) is withdrawn from the tank, passed through a heat exchanger, and then the chilled liquid is sprayed back into the tank through a spraybar. The test series will be performed over a 20-30 day period. Tests will be conducted at multiple fill levels to demonstrate concept viability and to provide benchmark data to be used in analytical model development. In this paper the test set-up and test procedures are presented.

Hedayat, Ali↗
NASA NTRS1998

Exercise Thermoregulation in Men after One and 24-hours of 6 Degree Head-Down Tilt

Exercise thermoregulation exercise is dependent on heat loss by increased skin blood flow (convective and conductive heat loss) and through enhanced sweating (evaporative heat loss). Reduction of plasma volume (PV), increased plasma osmolality, physical deconditioning, and duration of exposure to simulated and actual microgravity reduces the ability to thermoregulate during exercise.

Ertl, A. C.↗
NASA NTRS2000

Exercise thermoregulation in men after 1 and 24-hours of 6 degrees head-down tilt

BACKGROUND: Exercise thermoregulation is dependent on heat loss by increased skin blood flow (convective and conductive heat loss) and through enhanced sweating (evaporative heat loss). Reduction of plasma volume (PV), increased plasma osmolality, physical deconditioning, and duration of exposure to simulated and actual microgravity reduces the ability to thermoregulate during exercise. HYPOTHESIS: We hypothesized that 24 h of head down tilt (HDT24) would alter thermoregulatory responses to a submaximal exercise test and result in a higher exercise rectal temperature (Tre) when compared with exercise Tre after 1 h of head down tilt (HDT1). METHODS: Seven men (31+/-SD 6 yr, peak oxygen uptake (VpO2peak) of 44+/-6 ml x kg(-1) x min(-1)) were studied during 70 min of supine cycling at 58+/-SE 1.5% VO2peak at 22.0 degrees C Tdb and 47% rh. RESULTS: Relative to pre-tilt sitting chair rest data, HDT1 resulted in a 6.1+/-0.9% increase and HDT24 in a 4.3+/-2.3% decrease in PV (delta = 10.4% between experiments, p<0.05) while plasma osmolality remained unchanged (NS). Pre-exercise Tre was elevated after HDT24 (36.71 degrees C +/-0.06 HDT1 vs. 36.93 degrees C+/-0.11 HDT24, p<0.05). The 70 min of exercise did not alter this relationship (p<0.05) with respective end exercise increases in Tre to 38.01 degrees C and 38.26 degrees C (degrees = 1.30 degrees C (HDT1) and 1.33 degrees C (HDT24)). While there were no pre-exercise differences in mean skin temperature (Tsk), a significant (p<0.05) time x treatment interaction occurred during exercise: after min 30 in HDT24 the Tsk leveled off at 31.1 degrees C, while it continued to increase reaching 31.5 degrees C at min 70 in HDT1. A similar response (NS) occurred in skin blood velocity. Neither local sweating rates nor changes in body weight during exercise of -1.63+/-0.24 kg (HDT1) or - 1.33+/-0.09 kg (HDT24) were different (NS) between experiments. CONCLUSION: While HDT24 resulted in elevated pre-exercise Tre, reduced PV, attenuation of Tsk and skin blood velocity during exercise, the absolute increase in exercise Tre was not altered. But if sweat rate and cutaneous vascular responses were similar at different core temperatures (unchanged thermoregulation), the Tre offset could have been caused by the HDT-induced hypovolemia.

NASA Program Biomedical Research and Countermeasur↗
NASA NTRS2008

Application of Synthetic Jets to Reduce Stator Flow Separation in a Low Speed Axial Compressor

Flow control using synthetic jet injection has been applied in a low speed axial compressor. The synthetic jets were applied from the suction surface of a stator vane via a span-wise row of slots pitched in the streamwise direction. Actuation was provided externally from acoustic drivers coupled to the vane tip via flexible tubing. The acoustic resonance characteristics of the system, and the resultant jet velocities were obtained. The effects on the separated flow field for various jet velocities and frequencies were explored. Total pressure loss reductions across the vane passage were measured. The effect of synthetic jet injection was shown to be comparable to that of pulsatory injection with mass addition for stator vanes which had separated flow. While only a weak dependence of the beneficial effect was noted based on the excitation frequency, a strong dependence on the amplitude was observed at all frequencies.

Braunscheidel, Edward P.↗
NASA NTRS2020

Local Food Crop Production can Fulfil Demand for Less than One-Third of the Population

The distance between the origin and end-point of food supply chains, and the ‘localness’ of food systems, are key considerations of many narratives associated with sustainability. Yet, information on the minimum distance to food crops is still scarce at the global level. Using an optimization model based on ‘foodsheds’ (that is, self-sufficient areas with internal dependencies), we calculate the potential minimum distance between food production and consumption for six crop types around the world. We show that only 11–28% of the global population can fulfil their demand for specific crops within a 100-km radius, with substantial variation between different regions and crops. For 26–64% of the population, that distance is greater than 1,000 km. Even if transnational foodsheds were in place, large parts of the globe would still depend on trade to feed themselves. Although yield gap closure and food loss reductions could favour more local food systems, particularly in Africa and Asia, global supply chains would still be needed to ensure an adequate and stable food supply.

Crop production↗