Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “level set”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2008

The Interaction of the Space Shuttle Launch and Entry Suits and Sustained Weightless on Astronaut Egress Locomotion

The purpose of this study was to determine the consequences of extended periods of weightlessness during space missions on astronauts f ability to perform a simulated contingency egress while wearing either of the Launch and Entry suits immediately after space flight. In our previous lab-based study of simulated contingency egress, we found only 4 of 12 non-astronauts wearing the Launch and Entry Suit (LES) successfully completed the simulated egress. However, 4 of 4 of the previous failures (when tested wearing the LES), were then successful in completing the test wearing the Advanced Crew Escape Suit (ACES). Therefore, this study tested 21 Astronaut Volunteers wearing either the LES or ACES while performing a simulated egress on a treadmill (TM) onboard the Crew Transportation Vehicle immediately after space flight at either the Kennedy Space Center or Edwards AFB. Astronauts walked for 400 meters at 1.6m/sec with g-suit inflation level set to preflight testing levels, visor down, breathing from the suit emergency O2 supply. Metabolic, heartrate, and perceived exertion data were collected during these post-flight tests. Exactly the same preflight simulated egress tests on a TM were performed in the lab at NASA/JSC by each crewmember at L-60. Preflight testing found 2 of the 21 crewmembers were unable to complete the simulated contingency egress. Postflight, 9 crew (8 ACES, 1 LES) completed the simulated contingency egress of 400 meters at 1.6m/sec. and 12 failed to meet that standard (7 ACES, 5 LES). Preflight physiological response tests failed to identify crew capable of performing the egress vs. those who failed. However, 18 of the 21 crew did make at least 2.67 minutes into the postflight egress testing. At that point in time, heartrate was higher (P <=.20) for the failures compared to the finishers. These findings indicate that NASA fs switch to the ACES for space flight crews should be expedited.

Greenisen, M. C.↗
NASA NTRS1990

Development and applications of a multi-level strain energy method for detecting finite element modeling errors

A computational procedure is described which can be used efficiently in identifying modeling errors which may arise from development of a structural finite element model. The procedure, which is referred to as the multi-level strain energy check, is set up in the form of a set of NASTRAN DMAP alters which provide sufficient information about the modeling errors at G-Set, N-Set, and F-Set levels. This technique was applied to two NASTRAN models, namely, the AH-64A and AH-1G models. Two modeling errors were identified for the AH-1G, which were then corrected.

Hashemi-Kia, Mostafa↗
NASA NTRS1978

Hybrid random-sound test-control system

Controller develops gain-control signals by comparing detected sound levels in each band with reference set levels. By eliminating multiplexing network and single clock used in digital system, design allows servocontrol rate for each band to be adjusted independently.

Woodbury, R. C.↗
NASA NTRS1991

Unstructured grid generation using the distance function

A new class of methods for obtaining level sets to generate unstructured grids is presented. The consecutive grid levels are computed using the distance functions, which corresponds to solving the Hamilton-Jacobi equations representing the equations of motion of fronts propagating with curvature-dependent speed. The relationship between the distance function and the governing equations will be discussed as well as its application to generating grids. Multi-ply connected domains and complex geometries are handled naturally, with a straightforward generalization to several space dimensions. The grid points for the unstructured grid are obtained simultaneously with the grid levels. The search involved in checking for overlapping triangles is minimized by triangulating the entire domain one level at a time.

Bihari, Barna L.↗
NASA NTRS1974

Exospheric temperature and composition from satellite beacon measurements

Routine measurements of the slab thickness of the ionosphere, from 1965 to 1971, are used to infer the changes in neutral temperature and ion composition at a mean latitude of 40 S. Values of neutral temperature at solar maximum are 5 to 10% above Northern Hemisphere backscatter results. The diurnal and seasonal changes agree closely with satellite drag and backscatter measurements, except that the maximum temperature occurs after sunset in winter. Winter night-time values of the O(+)/H(+) transition height were 500 km in 1965-1966, 800 km in 1968-1969, and 700 km in 1971. Changes in the transition height lag about six months behind the changes in solar flux. Diurnal variations have a minimum just before sunrise and a maximum 1 to 3 hr after noon. On winter nights the transition height descends to the level set by chemical equilibrium. On summer nights the transition height is always above this level, giving a continual production of H(+) which serves as an additional source for maintaining the night-time ionosphere in the winter hemisphere.

Titheridge, J. E.↗
NASA NTRS1994

Oscillator strengths of selected resonance transitions in neutral sulfur

Mean lives and branching ratios for the 4s (3)S(sup 0 sub 1) and 4s(double prime) (3)P(sup 0 sub 1, 2) levels of neutral sulfur were determined at the Toledo Heavy Ion Accelerator using beam-foil spectroscopic techniques. The mean lives obtained for the 4s (3)S(sup 0 sub 1) 4s(double prime) (3)P(sup 0 sub 1), and (3)P(sup 0 sub 2) levels, 1.875 +/- 0.094 ns, 2.034 +/- 0.102 ns, and 2.146 +/- 0.129 ns, respectively, represent the most accurate results available to date. Oscillator strengths for the transitions 3p(sup 4)(3)P(sub 2, 1, 0)-4s (3)S(sup 0 sub 1) and 3p(sup 4)(3)P(sub 2, 1, 0)-4s(double prime) (3)P(sup 0 sub 1, 2) were derived from these mean lives together with the measured branching ratios. For comparison with published results which present only multiplet f-values, such f-values were computed from the measured individual line oscillator strengths. The value obtained for the 3p(sup 4)(3)P-4s(sup 3)S(sup 0) multiplet at 1814 A is 0.088 +/- 0.005, in good agreement with the mean of previous experimental measurements and theoretical calculations. With the mean life for the 4s(double prime) 3P(sup 0 sub 0) level set equal to the mean of our determination for the other two 4s(double prime) (3)P(sup 0) levels (a valid assumption for LS coupling conditions, and consistent with the observed equality of the mean lives within the accuracy of our measurement), an oscillator strength for the 1299 A multiplet of 0.121 +/- 0.004 was found. Both results are in good agreement with recent large-scale theoretical calculations that incorporate the effects of configuration interaction.

Beideck, D. J.↗
NASA NTRS2006

Space and Ground Trades for Human Exploration and Wearable Computing

Human exploration of the Moon and Mars will present unique trade study challenges as ground system elements shift to planetary bodies and perhaps eventually to the bodies of human explorers in the form of wearable computing technologies. This presentation will highlight some of the key space and ground trade issues that will face the Exploration Initiative as NASA begins designing systems for the sustained human exploration of the Moon and Mars, with an emphasis on wearable computing. We will present some preliminary test results and scenarios that demonstrate how wearable computing might affect the trade space noted below. We will first present some background on wearable computing and its utility to NASA's Exploration Initiative. Next, we will discuss three broad architectural themes, some key ground and space trade issues within those themes and how they relate to wearable computing. Lastly, we will present some preliminary test results and suggest guidance for proceeding in the assessment and creation of a value-added role for wearable computing in the Exploration Initiative. The three broad ground-space architectural trade themes we will discuss are: 1. Functional Shift and Distribution: To what extent, if any, should traditional ground system functionality be shifted to, and distributed among, the Earth, Moon/Mars, and the human. explorer? 2. Situational Awareness and Autonomy: How much situational awareness (e.g. environmental conditions, biometrics, etc.) and autonomy is required and desired, and where should these capabilities reside? 3. Functional Redundancy: What functions (e.g. command, control, analysis) should exist simultaneously on Earth, the Moon/Mars, and the human explorer? These three themes can serve as the axes of a three-dimensional trade space, within which architectural solutions reside. We will show how wearable computers can fit into this trade space and what the possible implications could be for the rest of the ground and space architecture(s). We intend this to be an example of explorer-centric thinking in a fully integrated explorer paradigm, where integrated explorer refers to a human explorer having instant access to all relevant data, knowledge of the environment, science models, health and safety-related events, and other tools and information via wearable computing technologies. The trade study approach will include involvement from the relevant stakeholders (Constellation Systems, CCCI, EVA Project Office, Astronaut office, Mission Operations, Space Life Sciences, etc.) to develop operations concepts (and/or operations scenarios) from which a basic high-level set of requirements could be extracted. This set of requirements could serve as a foundation (along with stakeholder buy-in) that would help define the trade space and assist in identifying candidate technologies for further study and evolution to higher-level technology readiness levels.

Lupisella, Mark↗
NASA NTRS1992

Consumables and wastes estimations for the First Lunar Outpost

The First Lunar Outpost mission is a design reference mission for the first human return to the moon. This paper describes a set of consumables and waste material estimations made on the basis of the First Lunar Outpost mission scenario developed by the NASA Exploration Programs Office. The study includes the definition of a functional interface framework and a top-level set of consumables and waste materials to be evaluated, the compilation of mass flow information from mission developers supplemented with information from the literature, and the analysis of the resulting mass flow information to gain insight about the possibility of material flow integration between the moon outpost elements. The results of the study of the details of the piloted mission and the habitat are used to identify areas where integration of consumables and wastes across different mission elements could provide possible launch mass savings.

Theis, Ronald L. A.↗
NASA NTRSDate not supplied

CDC Bioreactor Configuration Method for Volume Level Control with Controlled Inlet and Outlet Flow

Environmental Control Life Support Systems and other microbiological biofilm studies often utilize small scale bioreactors. Among these options are the popular BioSurface CDC bioreactors, currently being utilized by Marshall Space Flight Center groups researching the impact of biofilms on life support systems. After a recent experimental regime, it was determined additional equipment could be added to augment the capabilities of the bioreactors. Previous research configurations such as ASTM E3161 – 18 relied on an outlet stream gravity draining from a side drain port located above sampling coupons. This limited applications to experimental conditions with a controlled inlet and uncontrolled outlet flow. With the introduction of a small single pole single throw (SPST) reed float switch, a peristaltic pump connected to the outlet drain and a chassis controller, the bioreactor is able to maintain a set level. The modification allows additional variables to be tested, including highly adjustable fill and flush cycles, bioreactor volume, draining and filling control. Once the configuration modifications were implemented through the installation of the new equipment, data was collected to ensure the stability of the level measurements. As the level control switch is a float switch, consideration was taken into account for effects of internal stirring speed, along with effects of inlet and outlet flow rate. Data presented in this study will illustrate the stability and effectiveness of the configuration changes in equipment made to the bioreactor. These configuration changes are proving an effective control method to conduct biofilm mitigation techniques for ECLSS hardware research. The controlled level capabilities allow for a constant drip feed flow rate into the bioreactors, a key aspect of the biofilm mitigation testing.

CDC Bioreactor↗
NASA NTRSDate not supplied

CDC Bioreactor Configuration Method for Volume Level Control with Controlled Inlet and Outlet Flow

Environmental Control Life Support Systems and other microbiological biofilm studies often utilize small scale bioreactors. Among these options are the popular BioSurface CDC bioreactors, currently being utilized by Marshall Space Flight Center groups researching the impact of biofilms on life support systems. After a recent experimental regime, it was determined additional equipment could be added to augment the capabilities of the bioreactors. Previous research configurations such as ASTM E3161-21 relied on an outlet stream gravity draining from a side drain port located above sampling coupons. This limited applications to experimental conditions with a controlled inlet and uncontrolled outlet flow. With the introduction of a small single pole single throw (SPST) reed float switch and a peristaltic pump connected to the outlet drain and a chassis controller, the bioreactor is able to maintain a set level. The modification allows additional variables to be tested, including highly adjustable fill and flush cycles, bioreactor volume, draining and filling control. Once the configuration modifications were implemented through the installation of the new equipment, data was collected to ensure the stability of the level measurements. As the level control switch is a float switch, consideration was taken into account for effects of internal stirring speed, along with effects of inlet and outlet flow rate. Data presented in this study will illustrate the stability and effectiveness of the configuration changes in equipment made to the bioreactor. These configuration changes have demonstrated control method to conduct biofilm mitigation techniques for ECLSS hardware research. The controlled level capabilities allow for a constant drip feed flow rate into the bioreactors, a key aspect of the biofilm mitigation testing.

CDC Bioreactor↗
NASA NTRSDate not supplied

CDC Bioreactor Configuration Method for Volume Level Control with Controlled Inlet and Outlet Flow

Environmental Control Life Support Systems and other microbiological biofilm studies often utilize small scale bioreactors. Among these options are the popular BioSurface CDC bioreactors, currently being utilized by Marshall Space Flight Center groups researching the impact of biofilms on life support systems. After a recent experimental regime, it was determined additional equipment could be added to augment the capabilities of the bioreactors. Previous research configurations such as ASTM E3161-21 relied on an outlet stream gravity draining from a side drain port located above sampling coupons. This limited applications to experimental conditions with a controlled inlet and uncontrolled outlet flow. With the introduction of a small single pole single throw (SPST) reed float switch and a peristaltic pump connected to the outlet drain and a chassis controller, the bioreactor is able to maintain a set level. The modification allows additional variables to be tested, including highly adjustable fill and flush cycles, bioreactor volume, draining and filling control. Once the configuration modifications were implemented through the installation of the new equipment, data was collected to ensure the stability of the level measurements. As the level control switch is a float switch, consideration was taken into account for effects of internal stirring speed, along with effects of inlet and outlet flow rate. Data presented in this study will illustrate the stability and effectiveness of the configuration changes in equipment made to the bioreactor. These configuration changes have demonstrated control method to conduct biofilm mitigation techniques for ECLSS hardware research. The controlled level capabilities allow for a constant drip feed flow rate into the bioreactors, a key aspect of the biofilm mitigation testing.

CDC Bioreactor↗
NASA NTRSDate not supplied

CDC Bioreactor Configuration Method for Volume Level Control with Controlled Inlet and Outlet Flow

Environmental Control Life Support Systems and other microbiological biofilm studies often utilize small scale bioreactors. Among these options are the popular BioSurface CDC bioreactors, currently being utilized by Marshall Space Flight Center groups researching the impact of biofilms on life support systems. After a recent experimental regime, it was determined additional equipment could be added to augment the capabilities of the bioreactors. Previous research configurations such as ASTM E3161-21 relied on an outlet stream gravity draining from a side drain port located above sampling coupons. This limited applications to experimental conditions with a controlled inlet and uncontrolled outlet flow. With the introduction of a small single pole single throw (SPST) reed float switch and a peristaltic pump connected to the outlet drain and a chassis controller, the bioreactor is able to maintain a set level. The modification allows additional variables to be tested, including highly adjustable fill and flush cycles, bioreactor volume, draining and filling control. Once the configuration modifications were implemented through the installation of the new equipment, data was collected to ensure the stability of the level measurements. As the level control switch is a float switch, consideration was taken into account for effects of internal stirring speed, along with effects of inlet and outlet flow rate. Data presented in this study will illustrate the stability and effectiveness of the configuration changes in equipment made to the bioreactor. These configuration changes have demonstrated control method to conduct biofilm mitigation techniques for ECLSS hardware research. The controlled level capabilities allow for a constant drip feed flow rate into the bioreactors, a key aspect of the biofilm mitigation testing.

CDC Bioreactor↗
NASA NTRS1977

Severe weather prediction studies

A numerical forecast model is described which uses three-dimensional primitive equations to predict the evolution of the wind, temperature and moisture fields along with the subsynoptic-scale convective activity. There are 15 vertical levels set on a longitude-latitude horizontal grid. In this study, the horizontal grid distance is 70 km (0.625 deg latitude and 0.816 deg longitude at 40 deg N) and the time step is 90 sec. Orography is included and terrain coordinates are adopted. The forecast model is used to test two tornado-producing storms with very different synoptic structures. A 12 hr forecast is carried out for both cases. The rms errors of the forecast indicate much smaller errors in the middle troposphere than in the lower troposphere. The results demonstrate that a rather fine-mesh limited-area numerical model is capable of providing a valuable short-range forecast of the circulation and the mesoscale precipitation features.

Chang, C.-B.↗
NASA NTRS1978

An inverter/controller subsystem optimized for photovoltaic applications

Conversion of solar array dc power to ac power stimulated the specification, design, and simulation testing of an inverter/controller subsystem tailored to the photovoltaic power source characteristics. This paper discusses the optimization of the inverter/controller design as part of an overall Photovoltaic Power System (PPS) designed for maximum energy extraction from the solar array. The special design requirements for the inverter/controller include: (1) a power system controller (PSC) to control continuously the solar array operating point at the maximum power level based on variable solar insolation and cell temperatures; and (2) an inverter designed for high efficiency at rated load and low losses at light loadings to conserve energy. It must be capable of operating connected to the utility line at a level set by an external controller (PSC).

Pickrell, R. L.↗
NASA NTRS1981

Application of the MNA design method to a nonlinear turbofan engine

Using nonlinear digital simulation as a representative model of the dynamic operation of the QCSEE turbofan engine, a feedback control system is designed by variable frequency design techniques. Transfer functions are generated for each of five power level settings covering the range of operation from approach power to full throttle (62.5% to 100% full power). These transfer functions are then used by an interactive control system design synthesis program to provide a closed loop feedback control using the multivariable Nyquist array and extensions to multivariable Bode diagrams and Nichols charts.

Leininger, G. G.↗
NASA NTRS1986

The 14 month wind stressed residual circulation (pole tide) in the North Sea

From published research it is known that a quasi-periodic 14 month atmospheric pressure oscillation of a few tenths of a millibar exists in the region of the North and Baltic Seas. At some time in the cycle the associated wind stress has a westerly component that drives a circulation in the North Sea. The results of a dynamical model and comparisons with several North Sea residual circulation studies show that a large sea level gradient results along the Dutch coast. It is this feature that has been referred to as the enhanced pole tide. The dynamical similarity of this pole tide in the North and Baltic Seas to the annual and seasonal wind forced circulations is considered. It is inferred that the large deviations of the pole tide from equilibrium at coastal stations are the result of this sea level set up forces by the 14 month wind stress cycle.

Oconnor, W. P.↗
NASA NTRS1987

Imaging performance of annular apertures. VI - Limitations by optical surface deviations

The performance of optical systems is limited by imperfect optical surfaces that degrade the images below the level set by wave theoretical limits. The central irradiance functions are derived for slit and circular apertures with five distributions of wavefront errors and for a range of maximal wavefront deviations. For practical frequency of occurrence distributions of wavefront deviations, the point spread and the image energy integral functions are determined. Practical performances of optical systems are derived and performance limits discussed.

Tschunko, Hubert F. A.↗
NASA NTRS1990

The heat of formation of CN radicals and radiative lifetimes of the A 1 Sigma - state of C2N2

Radiative lifetimes have been measured for the stable vibrational levels of the A 1 sigma - electronic state of C2N2. They range from 1.3 microsec for the 4(sub 0)(sup 1) level to 0.66 microsec for the 1(sub 0)(sup 1) 4(sub 0)(sup 1) level and in general decrease with increasing vibrational excitation. Self-quenching rate constants range from gas kinetic to ten times that. Foreign gas quenching rates are slower. Observation of emission from the 1(sub 0)(sup 1) 4(sub 0)(sup 1) level sets a lower limit for the heat of formation of CN of 439.11 kJ/mol.

Barts, Samuel A.↗