Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “lead optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Aircraft Trajectory Design Based on Reducing the Combined Effects of Carbon-di-oxide, Nitrogen and Contrails

Aircraft operations need to meet the combined requirements of safety, efficiency, capacity and reduced environmental impact. Aircraft routes can be made efficient by flying wind optimal routes. However, the desire to reduce the impact of aviation emissions and contrails may result in trajectories, which deviate from wind optimal trajectories leading to extra fuel use. The lifetime associated with different emissions and contrails varies from a few hours to several hundred years. The impact of certain gases depends on the amount and location of the emission, and the decision-making horizon, in years, when the impact is estimated. The Absolute Global Temperature Potential (AGTP) is used as a metric to measure the combined effects of emissions and contrails. This paper extends earlier work by the authors to include the effect of oxides of nitrogen in the development of aircraft trajectories to reduce the combined effects of carbon dioxide, oxides of nitrogen (NOX) and contrails. The methodology is applied to air traffic in the continental US. The paper shows the trade-offs between reducing emissions and the cost of extra fuel using a fuel sensitivity index, defined as the reduction in AGTP per kg of fuel. The paper shows the performance of the optimization strategy for decision intervals of 10, 25 and 100 years. Based on the simplified models, the inclusion of NOX emissions has a slight influence on the minimal climate impact trajectories when the decision horizons are around 25 years.

Sridhar, Banavar↗
NASA NTRS2019

Efficient computation of optimal low thrust gravity perturbed orbit transfers

We have developed a new method for solving low-thrust fuel-optimal orbit transfer problems in the vicinity of a large body (planet or asteroid), considering a high-fidelity spherical harmonic gravity model. The algorithm is formulated via the indirect optimization method, leading to a two-point boundary value problem (TPBVP). We make use of a hyperbolic tangent smoothing law for performing continuation on the thrust magnitude to reduce the sharpness of the control switches in early iterations and thus promote convergence. The TPBVP is solved using the method of particular solutions (MPS) shooting method and Picard-Chebyshev numerical integration. Application of Picard-Chebyshev integration affords an avenue for increased efficiency that is not available with step-by-step integrators. We demonstrate that computing the particular solutions with only a low-fidelity force model greatly increases the efficiency of the algorithm while ultimately achieving near machine precision accuracy. A salient feature of the MPS is that it is parallelizable, and thus further speedups are available. It is also shown that, for near Earth orbits and over a small number of en-route revolutions around the Earth, only the zonal perturbation terms are required in the costate equations to obtain a solution that is accurate to machine precision and optimal to engineering precision. The proposed framework can be used for trajectory design around small asteroids and also for orbit debris rendezvous and removal tasks.

Junkins, John L.↗
NASA NTRS1978

Analysis of a theoretically optimized transonic airfoil

Numerical optimization was used in conjunction with an inviscid, full potential equation, transonic flow analysis computer code to design an upper surface contour for a conventional airfoil to improve its supercritical performance. The modified airfoil was tested in a compressible flow wind tunnel. The modified airfoil's performance was evaluated by comparison with test data for the baseline airfoil and for an airfoil developed by optimization of leading edge of the baseline airfoil. While the leading edge modification performed as expected, the upper surface re-design did not produce all of the expected performance improvements. Theoretical solutions computed using a full potential, transonic airfoil code corrected for viscosity were compared to experimental data for the baseline airfoil and the upper surface modification. These correlations showed that the theory predicted the aerodynamics of the baseline airfoil fairly well, but failed to accurately compute drag characteristics for the upper surface modification.

Lores, M. E.↗
NASA NTRS1979

Pseudo-direct solution to the boundary-layer equations for separated flow

This paper describes a procedure for the automatic iteration of an inverse boundary-layer technique to a prescribed pressure distribution in a separated flow. The technique is demonstrated by computation of two transonic airfoil flows and two externally generated shock boundary-layer interaction flows. These results are compared to experimental data and to solutions of the full Navier-Stokes equations. These comparisons indicate that substantial economies can be obtained by applying methods like the present, in lieu of full Navier-Stokes methods, in zonal calculation schemes for design purposes. The optimization technique leading to convergence is described in detail and a table of typical computation time is presented.

Arieli, R.↗
NASA NTRS1989

Design challenges for space bioreactors

The design of bioreactors for operation under conditions of microgravity presents problems and challenges. Absence of a significant body force such as gravity can have profound consequences for interfacial phenomena. Marangoni convection can no longer be overlooked. Many speculations on the advantages and benefits of microgravity can be found in the literature. Initial bioreactor research considerations for space applications had little regard for the suitability of the designs for conditions of microgravity. Bioreactors can be classified in terms of their function and type of operation. The complex interaction of parameters leading to optimal design and operation of a bioreactor is illustrated by the JSC mammalian cell culture system. The design of a bioreactor is strongly dependent upon its intended use as a production unit for cell mass and/or biologicals or as a research reactor for the study of cell growth and function. Therefore a variety of bioreactor configurations are presented in rapid summary. Following this, a rationale is presented for not attempting to derive key design parameters such as the oxygen transfer coefficient from ground-based data. A set of themes/objectives for flight experiments to develop the expertise for design of space bioreactors is then proposed for discussion. These experiments, carried out systematically, will provide a database from which engineering tools for space bioreactor design will be derived.

Seshan, P. K.↗
NASA NTRS1990

Parameter learning for performance adaptation

A parameter learning method is introduced and used to broaden the region of operability of the adaptive control system of a flexible space antenna. The learning system guides the selection of control parameters in a process leading to optimal system performance. A grid search procedure is used to estimate an initial set of parameter values. The optimization search procedure uses a variation of the Hooke and Jeeves multidimensional search algorithm. The method is applicable to any system where performance depends on a number of adjustable parameters. A mathematical model is not necessary, as the learning system can be used whenever the performance can be measured via simulation or experiment. The results of two experiments, the transient regulation and the command following experiment, are presented.

Peek, Mark D.↗
NASA NTRS1993

An optimized finite-difference scheme for wave propagation problems

Two fully-discrete finite-difference schemes for wave propagation problems are presented, a maximum-order scheme and an optimized (or spectral-like) scheme. Both combine a seven-point spatial operator and an explicit six-stage time-march method. The maximum-order operator is fifth-order in space and is sixth-order in time for a linear problem with periodic boundary conditions. The phase and amplitude errors of the schemes obtained using Fourier analysis are given and compared with a second-order and a fourth-order method. Numerical experiments are presented which demonstrate the usefulness of the schemes for a range of problems. For some problems, the optimized scheme leads to a reduction in global error compared to the maximum-order scheme with no additional computational expense.

Zingg, D. W.↗
NASA NTRS1990

An information driven strategy to support multidisciplinary design

The design of complex engineering systems such as aircraft, automobiles, and computers is primarily a cooperative multidisciplinary design process involving interactions between several design agents. The common thread underlying this multidisciplinary design activity is the information exchange between the various groups and disciplines. The integrating component in such environments is the common data and the dependencies that exist between such data. This may be contrasted to classical multidisciplinary analyses problems where there is coupling between distinct design parameters. For example, they may be expressed as mathematically coupled relationships between aerodynamic and structural interactions in aircraft structures, between thermal and structural interactions in nuclear plants, and between control considerations and structural interactions in flexible robots. These relationships provide analytical based frameworks leading to optimization problem formulations. However, in multidisciplinary design problems, information based interactions become more critical. Many times, the relationships between different design parameters are not amenable to analytical characterization. Under such circumstances, information based interactions will provide the best integration paradigm, i.e., there is a need to model the data entities and their dependencies between design parameters originating from different design agents. The modeling of such data interactions and dependencies forms the basis for integrating the various design agents.

Rangan, Ravi M.↗
NASA NTRS1995

Baseline experimental investigation of an electrohydrodynamically assisted heat pipe

The increases in power demand and associated thermal management requirements of future space programs such as potential Lunar/Mars missions will require enhancing the operating efficiencies of thermal management devices. Currently, the use of electrohydrodynamically (EHD) assisted thermal control devices is under consideration as a potential method of increasing thermal management system capacity. The objectives of the currently described investigation included completing build-up of the EHD-Assisted Heat Pipe Test bed, developing test procedures for an experimental evaluation of the unassisted heat pipe, developing an analytical model capable of predicting the performance limits of the unassisted heat pipe, and obtaining experimental data which would define the performance characteristics of the unassisted heat pipe. The information obtained in the currently proposed study will be used in order to provide extensive comparisons with the EHD-assisted performance observations to be obtained during the continuing investigation of EHD-Assisted heat transfer devices. Through comparisons of the baseline test bed data and the EHD assisted test bed data, accurate insight into the performance enhancing characteristics of EHD augmentation may be obtained. This may lead to optimization, development, and implementation of EHD technology for future space programs.

Duncan, A. B.↗
NASA NTRS1997

A Parallel Pipelined Renderer for the Time-Varying Volume Data

This paper presents a strategy for efficiently rendering time-varying volume data sets on a distributed-memory parallel computer. Time-varying volume data take large storage space and visualizing them requires reading large files continuously or periodically throughout the course of the visualization process. Instead of using all the processors to collectively render one volume at a time, a pipelined rendering process is formed by partitioning processors into groups to render multiple volumes concurrently. In this way, the overall rendering time may be greatly reduced because the pipelined rendering tasks are overlapped with the I/O required to load each volume into a group of processors; moreover, parallelization overhead may be reduced as a result of partitioning the processors. We modify an existing parallel volume renderer to exploit various levels of rendering parallelism and to study how the partitioning of processors may lead to optimal rendering performance. Two factors which are important to the overall execution time are re-source utilization efficiency and pipeline startup latency. The optimal partitioning configuration is the one that balances these two factors. Tests on Intel Paragon computers show that in general optimal partitionings do exist for a given rendering task and result in 40-50% saving in overall rendering time.

Chiueh, Tzi-Cker↗
NASA NTRS2017

Stabilization of Hypersonic Boundary Layers by Linear and Nonlinear Optimal Perturbations

The effect of stationary, finite-amplitude, linear and nonlinear optimal perturbations on the modal disturbance growth in a Mach 6 axisymmetric flow over a 7 deg. half-angle cone with 0:126 mm nose radius and 0:305 m length is investigated. The freestream parameters (M = 6, Re(exp 1) = 18 x 10(exp. 6) /m) are selected to match the flow conditions of a previous experiment in the VKI H3 hypersonic tunnel. Plane-marching parabolized stability equations are used in conjunction with a partial-differential equation based planar eigenvalue analysis to characterize the boundary layer instability in the presence of azimuthally periodic streaks. The streaks are observed to stabilize nominally planar Mack mode instabilities, although oblique Mack mode and first-mode disturbances are destabilized. Experimentally measured transition onset in the absence of any streaks correlates with an amplification factor of N = 6 for the planar Mack modes. For high enough streak amplitudes, the transition threshold of N = 6 is not reached by the Mack mode instabilities within the length of the cone; however, subharmonic first-mode instabilities, which are destabilized by the presence of the streaks, do reach N = 6 near the end of the cone. The highest stabilization is observed at streak amplitudes of approximately 20 percent of the freestream velocity. Because the use of initial disturbance profiles based on linear optimal growth theory may yield suboptimal control in the context of nonlinear streaks, the computational predictions are extended to nonlinear optimal growth theory. Results show that by using nonlinearly optimal perturbation leads to slightly enhanced stabilization of plane Mack mode disturbances as well as reduced destabilization of subharmonic first-mode disturbances.

Incompressible boundary layer↗
NASA NTRS2021

Adaptive Aerostructures for Revolutionary Civil Supersonic Transportation

To enable commercially viable civil supersonic transport (SST) aircraft, innovative solutions must be developed to meet noise and efficiency requirements for overland flight. This research effort consists of a multidisciplinary team of academic and industrial experts exploring for the first time the potential of small real-time geometric outer mold line (OML) reconfigurations to minimize sonic boom signatures and aircraft drag in response to changing ambient conditions, thereby enabling noise-compliant overland supersonic flight. The team utilizes recent advances in supersonic computational fluid dynamic (CFD) methods, new noise prediction tools, and new design approaches to consider embedded highly energy-dense shape memory alloy (SMA) actuators for local shape modifications to an SST aircraft leading to optimal low boom signature and low drag in different environments. This university-led program will provide strategic leadership toward technology convergence that advances NASA's Aerospace Research Mission Directorate's (ARMD) research objectives with regard to Thrust 2: “Innovation in Commercial Supersonic Aircraft” by exploring for the first time enabling low-boom operation across a range of flight conditions via structural adaptivity, and will promote education of the next generation of engineers. The overall research strategy is to pursue three critical areas: the design of configurations for reducing boom, SMA material development and modeling, and technology feasibility demonstration in a relevant environment. Initially, the team will identify potential applications where structure or geometry adaptivity provides a benefit in noise or drag across the entire flight envelope. For selected applications/structural locations, required OML geometry changes will be determined based on analysis of sonic boom ground signature and drag reduction using new design tools, trade studies, and atmospheric sensing techniques. Designs will be developed and evaluated against requirements on loading, stroke length, and operational temperature. New alloy formulations will be developed tailored for both autonomous and controlled actuation modes. As the SMA material development matures, integrated system-level factors will be investigated. Optimized designs for small-scale distributed adaptivity applications of maximum benefit will then be matured and tested, moving toward demonstration of the innovative technology approaches at a TRL 4-5 and showing that sonic booms can be reduced by reconfiguration on demand.

Koushik Datta↗
NASA NTRS2020

Optimal Low Thrust Orbit Transfers for Space Telescope Refueling at SEL2

The James Webb Space Telescope (JWST), a ten billion-dollar infrared telescope with a 6.5m primary mirror to be launched in 2021, is designed to operate in a Halo orbit around the second Sun-Earth Lagrange point (SEL2) for five to ten years. At that point fuel for station keeping and attitude maneuvers will run out. Refueling missions to JWST, as well as to similar space telescope missions proposed for SEL2, could greatly enhance the “science-per-dollar” value and promote a more sustainable use of space assets. In this paper, we present a novel approach to designing fuel optimal trajectories that will allow the refueling spacecraft to arrive at the SEL2 Halo orbit with maximum final mass (i.e. fuel payload). The low thrust optimal control problem is formulated using an indirect optimization method, leading to a two-point boundary value problem with a bang-bang control structure. We make use of a hyperbolic tangent smoothing technique for performing continuation on the thrust magnitude to reduce the sharpness of the control switches in early iterations and, thus, promote convergence. The problem is posed and solved in the circular restricted three-body problem. In this dynamical system, invariant manifolds exist that can be utilized to reduce fuel consumption. The here presented methodology to this challenging and important problem in astrodynamics demonstrates a significant potential for low-cost refueling mission design.

Woollands, Robyn↗
NASA NTRS2000

Lessons Learned During Solutions of Multidisciplinary Design Optimization Problems

Optimization research at NASA Glenn Research Center has addressed the design of structures, aircraft and airbreathing propulsion engines. During solution of the multidisciplinary problems several issues were encountered. This paper lists four issues and discusses the strategies adapted for their resolution: (1) The optimization process can lead to an inefficient local solution. This deficiency was encountered during design of an engine component. The limitation was overcome through an augmentation of animation into optimization. (2) Optimum solutions obtained were infeasible for aircraft and air-breathing propulsion engine problems. Alleviation of this deficiency required a cascading of multiple algorithms. (3) Profile optimization of a beam produced an irregular shape. Engineering intuition restored the regular shape for the beam. (4) The solution obtained for a cylindrical shell by a subproblem strategy converged to a design that can be difficult to manufacture. Resolution of this issue remains a challenge. The issues and resolutions are illustrated through six problems: (1) design of an engine component, (2) synthesis of a subsonic aircraft, (3) operation optimization of a supersonic engine, (4) design of a wave-rotor-topping device, (5) profile optimization of a cantilever beam, and (6) design of a cvlindrical shell. The combined effort of designers and researchers can bring the optimization method from academia to industry.

Patnaik, Suna N.↗
NASA NTRS2013

Issues and Strategies in Solving Multidisciplinary Optimization Problems

Optimization research at NASA Glenn Research Center has addressed the design of structures, aircraft and airbreathing propulsion engines. The accumulated multidisciplinary design activity is collected under a testbed entitled COMETBOARDS. Several issues were encountered during the solution of the problems. Four issues and the strategies adapted for their resolution are discussed. This is followed by a discussion on analytical methods that is limited to structural design application. An optimization process can lead to an inefficient local solution. This deficiency was encountered during design of an engine component. The limitation was overcome through an augmentation of animation into optimization. Optimum solutions obtained were infeasible for aircraft and airbreathing propulsion engine problems. Alleviation of this deficiency required a cascading of multiple algorithms. Profile optimization of a beam produced an irregular shape. Engineering intuition restored the regular shape for the beam. The solution obtained for a cylindrical shell by a subproblem strategy converged to a design that can be difficult to manufacture. Resolution of this issue remains a challenge. The issues and resolutions are illustrated through a set of problems: Design of an engine component, Synthesis of a subsonic aircraft, Operation optimization of a supersonic engine, Design of a wave-rotor-topping device, Profile optimization of a cantilever beam, and Design of a cylindrical shell. This chapter provides a cursory account of the issues. Cited references provide detailed discussion on the topics. Design of a structure can also be generated by traditional method and the stochastic design concept. Merits and limitations of the three methods (traditional method, optimization method and stochastic concept) are illustrated. In the traditional method, the constraints are manipulated to obtain the design and weight is back calculated. In design optimization, the weight of a structure becomes the merit function with constraints imposed on failure modes and an optimization algorithm is used to generate the solution. Stochastic design concept accounts for uncertainties in loads, material properties, and other parameters and solution is obtained by solving a design optimization problem for a specified reliability. Acceptable solutions can be produced by all the three methods. The variation in the weight calculated by the methods was found to be modest. Some variation was noticed in designs calculated by the methods. The variation may be attributed to structural indeterminacy. It is prudent to develop design by all three methods prior to its fabrication. The traditional design method can be improved when the simplified sensitivities of the behavior constraint is used. Such sensitivity can reduce design calculations and may have a potential to unify the traditional and optimization methods. Weight versus reliability traced out an inverted-S-shaped graph. The center of the graph corresponded to mean valued design. A heavy design with weight approaching infinity could be produced for a near-zero rate of failure. Weight can be reduced to a small value for a most failure-prone design. Probabilistic modeling of load and material properties remained a challenge.

Patnaik, Surya↗
NASA NTRS1990

Inducing optimally directed non-routine designs

Non-routine designs are characterized by the creation of new variables and thus an expansion of the design space. These differ from routine designs in that the latter are restricted to a fixed set of variables and thus a pre-defined design space. In previous papers, the 1stPRINCE non-routine design methodology that expands the design space in such a way that optimal trends dictate the direction and form of this expansion is described. How inductive techniques can determine these optimal trends are examined. The induction techniques in 1stPRINCE utilize constraint information from monotonicity analysis to determine how to mutate the design space. The process observes the constraint information of mutated designs and induces trends from those constraints. Application of 1stPRINCE to a beam under flexural load leads to an optimally directed tapered beam. An interesting application of 1stPRINCE to determine the optimally directed shape of a spinning square block such that resistance to spinning is minimized leads to the discovery of a circular wheel.

Cagan, Jonathan↗
NASA NTRS2001

Improving Simulated Annealing by Replacing Its Variables with Game-Theoretic Utility Maximizers

The game-theory field of Collective INtelligence (COIN) concerns the design of computer-based players engaged in a non-cooperative game so that as those players pursue their self-interests, a pre-specified global goal for the collective computational system is achieved as a side-effect. Previous implementations of COIN algorithms have outperformed conventional techniques by up to several orders of magnitude, on domains ranging from telecommunications control to optimization in congestion problems. Recent mathematical developments have revealed that these previously developed algorithms were based on only two of the three factors determining performance. Consideration of only the third factor would instead lead to conventional optimization techniques like simulated annealing that have little to do with non-cooperative games. In this paper we present an algorithm based on all three terms at once. This algorithm can be viewed as a way to modify simulated annealing by recasting it as a non-cooperative game, with each variable replaced by a player. This recasting allows us to leverage the intelligent behavior of the individual players to substantially improve the exploration step of the simulated annealing. Experiments are presented demonstrating that this recasting significantly improves simulated annealing for a model of an economic process run over an underlying small-worlds topology. Furthermore, these experiments reveal novel small-worlds phenomena, and highlight the shortcomings of conventional mechanism design in bounded rationality domains.

Wolpert, David H.↗