Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “large scale additive manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Mars Ecopoiesis Testbed

Mars surface conditions where liquid water is absent were simulated for the purposes of laboratory research. A pressure-temperature (P-T) profile was maintained in which no combination of pressure or temperature corresponds to the liquid region of the water phase diagram. The triple point of pure water occurs at T = 0.1oC and P(H2O) = 6.01 mbar; therefore all temperatures and pressures must be kept below these values, respectively. A 35-day test was performed in a commercial planetary simulation system (Techshot, Inc., Greenville, IN) in which the minimum night-time temperature was -80oC, the maximum daytime temperature was +26oC, the simulated day-night light cycle in earth hours was 12-on and 12-off, and the total pressure of the pure CO2 atmosphere was maintained below 11 mbar. Any water present was allowed to equilibrate with the changing temperature and pressure. The gas phase was sampled into a CR1-A condensation-mirror low-pressure hygrometer, which uses liquid nitrogen (down to 77oK) to determine the dew point (Buck Technologies, Boulder, CO). Dew point was measured once every hour and recorded on a data logger, along with the varying temperature in the chamber, from which the partial pressure of water was calculated. The resulting calculated daily cycles were tracked on the water P-T diagram, and no points were found to fall within the liquid-phase region of the diagram. It is concluded that there was no liquid water present throughout the test except during the initial pump-down period when aqueous specimens were introduced on the first day (less than 1 hour). Mars regolith simulant was present during this test, and further investigation is needed to determine whether liquid water could have been present or absent in the regolith in the form of brine. Biological samples consisting of Cyanobacteria: Anabena sp., Chroococcidiopsis CCMEE171, Plectonema boryanum; Eubacteria: Bacillus subtilis, Pseudomonas aeruginosa, and Eukaryota: Chlorella ellipsoidia were maintained in the simulator under the above-described conditions. The exposed specimens were tested for intracellular esterase activity, chlorophyll content (where appropriate) and reproductive survival. All tests yielded low-level positive results in all cases. In parallel to these terrestrial studies a planned design study was undertaken for the proposed test bed. Design requirements include compact assembly for transport and installation on the planetary surface (multiple units per mission would be expected), protective internal package for the release of organisms, a means of atmosphere exchange, access to sunlight, a means of penetrating the planetary surface, and most importantly a means of acquiring regolith while meeting the requirements of planetary protection. In consultation with advisers a design was created, and a large-scale mock-up of this design was fabricated by additive manufacturing at Techshot, Inc. with moving parts that simulated the components of the design. The mock-up assembly has been demonstrated to interested parties. A means of detecting live metabolism will also be included in the test bed. Several options were reviewed, and it is concluded that, by the time the ecopoiesis test bed is ready for testing the optimum instrument will be the equivalent of a hand-held mass spectrometer for metabolic gas analysis. This will maximize versatility and reveal much more information than could a detector of a single product (such as molecular oxygen), and the

Ecopoiesis↗
NASA NTRSDate not supplied

Pragmatic Stress Prediction on Additively Manufactured Coupons

Prediction of residual stresses from process parameters for additively manufactured large metal parts is computationally expensive. NASA is currently developing meter-scale parts with direct energy deposition. Practically, the predictive computational methods need to efficiently scale-up to meter-scale parts. Coupled thermal-mechanical multi-physics simulations have been developed with the pragmatic method using ABAQUS, COMSOL Multiphysics, ALE3D software. The residual stresses are a result of the manufacturing process which creates thermal cycling of the build layers. The pragmatic method uses lumped thermal layers for stress predictions to reduce computational costs. The stress predictions as well as deformations of the different codes are compared with each other and with ANSYS Additive using identical material models, boundary and initial conditions. The codes were used to simulate three different geometries: a thin wall, hollow cylinder and twin-cantilever part. The coupon parts were then manufactured with Inconel-625. The residual stresses in these parts were measured using X-ray diffraction as well as neutron beam diffraction at NIST. The stress measurements for the two technologies are compared. The pragmatic stress prediction method enabled predictions of the multi-centimeter scale parts using desktop computer workstations in only a few hours for each coupon. The results of the simulated stress predictions compared favorably with the measured stresses even though thermally lumped layers were employed. Finally, a two-meter scale nozzle was simulated using ANSYS Additive. The simulations were used to examine the build orientation trade-space with respect to resulting geometric deformation. The predicted deformations were compared to measurements of an actual subscale part manufactured with direct energy deposition.

Additive Manufacturing↗
NASA NTRSDate not supplied

Pragmatic Stress Prediction on Additively Manufactured Coupons

Prediction of residual stresses from process parameters for additively manufactured large metal parts is computationally expensive. NASA is currently developing meter-scale parts with direct energy deposition. Practically, the predictive computational methods need to efficiently scale-up to meter-scale parts. Coupled thermal-mechanical multi-physics simulations have been developed with the pragmatic method using ABAQUS, COMSOL Multiphysics, ALE3D software. The residual stresses are a result of the manufacturing process which creates thermal cycling of the build layers. The pragmatic method uses lumped thermal layers for stress predictions to reduce computational costs. The stress predictions as well as deformations of the different codes are compared with each other and with ANSYS Additive using identical material models, boundary and initial conditions. The codes were used to simulate three different geometries: a thin wall, hollow cylinder and twin-cantilever part. The coupon parts were then manufactured with Inconel-625. The residual stresses in these parts were measured using X-ray diffraction as well as neutron beam diffraction at NIST. The stress measurements for the two technologies are compared. The pragmatic stress prediction method enabled predictions of the multi-centimeter scale parts using desktop computer workstations in only a few hours for each coupon. The results of the simulated stress predictions compared favorably with the measured stresses even though thermally lumped layers were employed. Finally, a two-meter scale nozzle was simulated using ANSYS Additive. The simulations were used to examine the build orientation trade-space with respect to resulting geometric deformation. The predicted deformations were compared to measurements of an actual subscale part manufactured with direct energy deposition.

pragmatic method↗
NASA NTRS2016

Using Powder Cored Tubular Wire Technology to Enhance Electron Beam Freeform Fabricated Structures

Electron Beam Freeform Fabrication (EBF3) is an additive manufacturing technique, developed at NASA Langley Research Center, capable of fabricating large scale aerospace parts. Advantages of using EBF3 as opposed to conventional manufacturing methods include, decreased design-to-product time, decreased wasted material, and the ability to adapt controls to produce geometrically complex parts with properties comparable to wrought products. However, to fully exploit the potential of the EBF3 process development of materials tailored for the process is required. Powder cored tubular wire (PCTW) technology was used to modify Ti-6Al-4V and Al 6061 feedstock to enhance alloy content, refine grain size, and create a metal matrix composite in the as-solidified structures, respectively.

Gonzales, Devon↗
NASA NTRSDate not supplied

Additive Manufacturing: Disrupting Global Supply Chains and Enabling Sustainable Development

The integration of new materials and innovative manufacturing technologies into product supply chains are critically needed to address human and societal needs and to promote sustainable development and economic competitiveness. Recently, there has been tremendous growth in the additive manufacturing (AM) landscape with the introduction of high- end machines suitable for industrial applications. In addition, availability of desktop 3-D printers as well as open source printers and platforms have also facilitated the large scale growth of distributed manufacturing. The paradigm shift in thinking, where one can turn their design into product on demand, is leading to new business models and challenging traditional models of product development and distribution. In this presentation, an overview of different AM technologies will be provided along with technical challenges and opportunities. Various examples of materials (polymers, ceramics, metals, hybrids, and multi material systems) and structures achieved from utilizing a wide variety of additive manufacturing approaches will be provided. Technical challenges and opportunities for the utilization of additive manufacturing as a powerful enabler for sustainable development and disruptive technological threat to global supply chains for different materials and systems will be presented.

Additive Manufacturing↗
NASA NTRSDate not supplied

Additive Manufacturing (AM) for Propulsion Component and System Applications

NASA MSFC is developing several areas of additive manufacturing (AM) for propulsion component and system applications. These developments include new AM process and material development, large-scale AM pathfinder component fabrication and hot-fire testing, AM-centric design methodology, modeling and simulation, post-processing advancements, and new design applications of AM in aerospace. Some specific areas NASA has focused is the development and commercial infusion of AM supply chain for materials such as copper-alloy GRCop (Cu-Cr-Nb), Hydrogen-resistant alloys (NASA HR-1, JBK-75), refractory-based alloys (C-103, W, Mo, new formulations), and bimetallic and multi-metallic AM processes. Additional efforts have been focused on large scale AM demonstrating complex thin-wall structures up to 60” diameter using directed energy deposition. Material characterization, properties and component hot-fire testing has been completed using many of these newly developed AM alloys/processes. NASA has also focused on improvements to post-processing including powder removal, surface enhancements, and support removal to further realize cost and schedule benefits to the overall supply chain. These developments are part of the NASA Rapid Analysis and Manufacturing Propulsion Technology (RAMPT), Low Cost Upper Stage Propulsion (LCUSP) and Long Life Additive Manufacturing (LLAMA) projects, in addition to internal IRAD, and external collaborations.

Additive Manufacturing↗
NASA NTRSDate not supplied

Principles of Directed Energy Deposition for Aerospace Applications

Metal Additive Manufacturing is changing how components are fabricated for rocket propulsion and aerospace applications. Many additive manufacturing technologies are evolving, and active research is being conducted across academia, industry, and government to advance processes, materials, design, post-processing and applications. While much focus has been on Laser Powder Bed Fusion (LPBF) techniques, several large-scale techniques are also rapidly evolving using directed energy deposition (DED).

Additive Manufacturing↗
NASA NTRS2020

Technology Advancements for Channel Wall Nozzle Manufacturing In Liquid Rocket Engines

A regeneratively-cooled or dump-cooled nozzle is a critical component for expansion of hot gases to enable high temperature and performance in liquid rocket engines systems. Regeneratively-cooled channel wall nozzles are a design solution used across the propulsion industry as a simplified method to fabricate the nozzle structure with internal coolant passages. The scale and complexity of the channel wall nozzle (CWN) design can be challenging to fabricate which results in extended lead times and higher costs. Some of these challenges include: 1) Unique and high temperature materials, 2) Tight tolerances on large parts during manufacturing and assembly to contain high pressure propellants, 3) Thin-walled features to maintain adequate wall temperatures, and 4) Unique manufacturing process operations and complex tooling. The United States (U.S.) National Aeronautics and Space Administration (NASA) and U.S. specialty manufacturing vendors are maturing modern fabrication techniques to reduce complexity and decrease costs associated with channel wall nozzle manufacturing technology. Additive Manufacturing (AM) is one of the key technology advancements under evaluation for channel wall nozzles. Much of additive manufacturing for propulsion components has focused on laser powder bed fusion (L-PBF), but the scale is not yet feasible for application to large scale nozzles. NASA is evolving directed energy deposition (DED) techniques for nozzles including arc-based deposition, blown powder deposition, and Laser Wire Direct Closeout (LWDC). There are different approaches being considered for fabrication of the nozzle, and each of these DED processes offer unique process steps for rapid fabrication. The arc-based and blown powder deposition techniques are used for the forming of the CWN liner. A variety of materials are being demonstrated including Inconel 625, Haynes 230, JBK-75, and NASA HR-1. The blown powder DED process is also being demonstrated for forming an integral channel nozzle in a single operation in similar materials. The LWDC process is a method for closing out the channels within the liner and forming the structural jacket using a localized laser wire deposition technique. Identical materials mentioned above have been used for this process in addition to bimetallic closeout (C-18150–SS347, and C-18150–Inconel 625). NASA has completed process development, material characterization, and hot-fire testing on a variety of these channel wall nozzle fabrication technique. This publication presents an overview of the various channel wall nozzle manufacturing processes and materials under evaluation including results from the hot-fire testing. Future development and technology focus areas is also discussed relative to channel wall nozzle manufacturing.

Additive manufacturing↗
NASA NTRS2004

AsterAnts: A Concept for Large-Scale Meteoroid Return and Processing using the International Space Station

AsterAnts is a concept calling for a fleet of solar sail powered spacecraft to retrieve large numbers of small (1/2-1 meter diameter) Near Earth Objects (NEOs) for orbital processing. AsterAnts could use the International Space Station (ISS) for NEO processing, solar sail construction, and to test NEO capture hardware. Solar sails constructed on orbit are expected to have substantially better performance than their ground built counterparts [Wright 1992]. Furthermore, solar sails may be used to hold geosynchronous communication satellites out-of-plane [Forward 1981] increasing the total number of slots by at least a factor of three. potentially generating $2 billion worth of orbital real estate over North America alone. NEOs are believed to contain large quantities of water, carbon, other life-support materials and metals. Thus. with proper processing, NEO materials could in principle be used to resupply the ISS, produce rocket propellant, manufacture tools, and build additional ISS working space. Unlike proposals requiring massive facilities, such as lunar bases, before returning any extraterrestrial larger than a typical inter-planetary mission. Furthermore, AsterAnts could be scaled up to deliver large amounts of material by building many copies of the same spacecraft, thereby achieving manufacturing economies of scale. Because AsterAnts would capture NEOs whole, NEO composition details, which are generally poorly characterized, are relatively unimportant and no complex extraction equipment is necessary. In combination with a materials processing facility at the ISS, AsterAnts might inaugurate an era of large-scale orbital construction using extraterrestrial materials.

Globus, Al↗
NASA NTRS2023

Reactive Additive Manufacturing for Fourth Industrial Revolution Exploration Systems (Ramfire) Aluminum 6061-Ram2 Nozzle Testing

The NASA Marshall Space Flight Center (MSFC) has applied various forms of metallic additive manufacturing (AM) in liquid rocket engine component design, development, and testing since 2010. These AM techniques reduce hardware cost, shorten fabrication schedules, increase reliability by reducing the number of joints, and improve hardware performance by allowing unconventional design. The RAMFIRE project, funded under Space Technology Mission Directorate (STMD) Game Changing Development (GCD) Program, has furthered the use of novel AM liquid rocket nozzles in collaboration with Elementum 3D. The project advanced novel large-scale AM aluminum material technology for significant weight savings in rocket engines and launch vehicles. Previously, aluminum alloys were difficult to weld and print using additive manufacturing. Elementum 3D’s patented Aluminum 6061-RAM2 alloy allows for aluminum alloys to be printed using various AM techniques and at various scales. The alloy can be leveraged for welding wire, showing drastic improvements in aluminum weldability. The RAMFIRE project focuses on five key areas: 1) Laser Powder Directed Energy Deposition (LP-DED) AL6061-RAM2 feedstock specification and verification, 2) LP-DED process development and validation, 3) LP-DED printed AL6061-RAM2 microstructural and mechanical property characterization, 4) Hot-fire test a 7k-lbf thrust class regeneratively cooled nozzle, 5) Print large scale regeneratively cooled nozzle. Hot-fire testing demonstrates potential of advanced space technologies to NASA and potential users by providing the relevant environments to advance TRL levels to the 5/6 range.

Al6061-RAM2↗
NASA NTRSDate not supplied

Packing and flow particle simulations

Granular material is present across natural and industrial processes on Earth and other planets. Granular particles show up in space exploration (lunar regolith), avalanches (boulders), food (coffee), construction (concrete powder) and manufacturing (additive manufacturing powder, battery slurries). Important phenomena emerge from large collections of granular particles. The size scales of the particles in granular material, 10 μm diameter or larger, makes particle-based simulations a tractable computational method. This seminar will present the packing and flow of granular matter using particle-based discrete element modeling simulations. Particles modeled with rotational friction only require as few as 2.6 contacts for mechanical stability, as opposed to 6 contacts for frictionless particles. Optimal parameters for in-space manufacturing particulate material are identified. Specifically, the maximum density and contacts occurs for a large-to-small particle volume ratio of 0.265. Stress and contact fabric fluctuations of flowing dry granular matter have power-law scaling with strain rate, and a kink. The pressure-dependent slope change kink could identify the transition between slower, quasistatic and faster, inertial flows.

granular↗
NASA NTRSDate not supplied

Packing and flow particle simulations

Granular material is present across natural and industrial processes on Earth and other planets. Granular particles show up in space exploration (lunar regolith), avalanches (boulders), food (coffee), construction (concrete powder) and manufacturing (additive manufacturing powder, battery slurries). Important phenomena emerge from large collections of granular particles. The size scales of the particles in granular material, 10 μm diameter or larger, makes particle-based simulations a tractable computational method. This seminar will present the packing and flow of granular matter using particle-based discrete element modeling simulations. Particles modeled with rotational friction only require as few as 2.6 contacts for mechanical stability, as opposed to 6 contacts for frictionless particles. Optimal parameters for in-space manufacturing particulate material are identified. Specifically, the maximum density and contacts occurs for a large-to-small particle volume ratio of 0.265. Stress and contact fabric fluctuations of flowing dry granular matter have power-law scaling with strain rate, and a kink. The pressure-dependent slope change kink could identify the transition between slower, quasistatic and faster, inertial flows.

granular↗
NASA NTRSDate not supplied

Lightweight Thrust Chamber Assemblies using Multi-Alloy Additive Manufacturing and Composite Overwrap

Additive Manufacturing (AM) has brought significant design and fabrication opportunities for complex components with internal features such as liquid rocket engine thrust chambers not previously possible. This technology allows for significant cost savings and schedule reductions in addition to new performance optimization through weight reduction and increased margins. Specific to regeneratively-cooled combustion chambers and nozzles for liquid rocket engines, additive manufacturing offers the ability to form the complex internal coolant channels and the closeout of the channels to contain the high pressure liquid propellants with a single operation. Much of additive manufacturing development has focused on monolithic alloys using Laser Powder Bed Fusion (L-PBF), which do not allow for complete optimization of the structure. The National Aeronautics and Space Administration (NASA) completed feasibility of an AM bimetallic L-PBF GRCop-84 copper-alloy combustion chamber with an AM electron beam freeform Inconel 625 structural jacket under the Low Cost Upper Stage Propulsion (LCUSP) Project. A follow-on project called Rapid Analysis and Manufacturing Propulsion Technology (RAMPT) is under development to further expand large-scale multi-alloy thrust chambers while maturing composite overwrap technology for significant weight savings opportunities. The RAMPT project has three primary objectives: 1) Advancing blown powder Directed Energy Deposition (DED) to fabricate integral-channel large scale nozzles, 2) Develop composite overwrap technology to reduce weight and provide structural capability for thrust chamber assemblies, and 3) Develop bimetallic and multi-metallic additively manufactured radial and axial joints to optimize material performance. In addition to these primary manufacturing developments, analytical modeling efforts compliment the process development to simulate the AM processes to reduce build failures and distortions. The RAMPT project is also maturing the supply chain for various manufacturing processes described above in addition to L-PBF of GRCop-42. This paper will present an overview of the RAMPT project, the process development and hardware progress to date, material and hot-fire testing results, along with future developments.

Additive Manufacturing↗
NASA NTRS2019

Channel Wall Nozzle Manufacturing Technology Advancements for Liquid Rocket Engines

A regeneratively-cooled nozzle is a critical component for expansion of the hot gases to enable high temperature and performance liquid rocket engines systems. Channel wall nozzles are a design solution used across the propulsion industry as a simplified method to fabricate the nozzle structure with internal coolant passages. The scale and complexity of the channel wall nozzle (CWN) design is challenging to fabricate leading to extended lead times and higher costs. Some of these challenges include: 1) unique and high temperature materials, 2) Tight tolerances during manufacturing and assembly to contain high pressure propellants, 3) thin-walled features to maintain adequate wall temperatures, and 4) Unique manufacturing process operations and tooling. The United States (U.S.) National Aeronautics and Space Administration (NASA) along with U.S. specialty manufacturing vendors are maturing modern fabrication techniques to reduce complexity and decrease costs associated with channel wall nozzle manufacturing technology. Additive Manufacturing (AM) is one of the key technology advancements being evaluated for channel wall nozzles. Much of additive manufacturing for propulsion components has focused on powder bed fusion, but the scale is not yet feasible for application to large scale nozzles. NASA is evolving directed energy deposition (DED) techniques for nozzles including arc-based deposition, blown powder deposition, and Laser Wire Direct Closeout (LWDC). There are different approaches being considered for fabrication of the nozzle and each of these DED processes offer unique process steps for rapid fabrication. The arc-based and blown powder deposition techniques are being used for the forming of the CWN liner. A variety of materials are being demonstrated including Inconel 625, Haynes 230, JBK-75, and NASA HR-1. The blown powder DED process is also being demonstrated for forming an integral channel nozzle in a single operation in similar materials. The LWDC process is a method for closing out the channels within the liner and forming the structural jacket using a localized laser wire deposition technique. Identical materials mentioned above have been used for this process in addition to bimetallic closeout (C-18150–SS347, and C-18150–Inconel 625). NASA has completed process development, material characterization, and hot-fire testing on a variety of these channel wall nozzle fabrication techniques. This paper will present an overview of the various processes and materials being evaluated and the results from the hot-fire testing. Future development and technology focus areas will also be discussed relative to channel wall nozzle manufacturing.

Gradl, Paul R.↗
NASA NTRSDate not supplied

Principles of Directed Energy Deposition for Aerospace Applications

Metal Additive Manufacturing is changing how components are being fabricated for rocket propulsion and aerospace applications. Many additive manufacturing technologies are evolving, and active research is being conducted across academia, industry, and government to advance processes, materials, design, post-processing, and applications. While much focus has been on Laser Powder Bed Fusion (L-PBF) techniques, several large-scale techniques are also rapidly evolving using directed energy deposition (DED) techniques. This lecture will provide an overview of various DED technologies, a comparison among the technologies, various materials, parameters used to deposit, and several examples of DED applications for propulsion and aerospace components.

Additive Manufacturing↗
NASA NTRS2000

Impact of Parallel Computing on Large Scale Aeroelastic Computations

Aeroelasticity is computationally one of the most intensive fields in aerospace engineering. Though over the last three decades the computational speed of supercomputers have substantially increased, they are still inadequate for large scale aeroelastic computations using high fidelity flow and structural equations. In addition to reaching a saturation in computational speed because of changes in economics, computer manufactures are stopping the manufacturing of mainframe type supercomputers. This has led computational aeroelasticians to face the gigantic task of finding alternate approaches for fulfilling their needs. The alternate path to over come speed and availability limitations of mainframe type supercomputers is to use parallel computers. During this decade several different architectures have evolved. In FY92 the US Government started the High Performance Computing and Communication (HPCC) program. As a participant in this program NASA developed several parallel computational tools for aeroelastic applications. This talk describes the impact of those application tools on high fidelity based multidisciplinary analysis.

Guruswamy, Guru P.↗
NASA NTRS2018

Buckling Response of a Large-Scale, Seamless, Orthogrid-Stiffened Metallic Cylinder

Results from the buckling test of a compression-loaded 8-ft-diameter seamless (i.e., without manufacturing joints), orthogrid-stiffened metallic cylinder are presented. This test was used to assess the buckling response and imperfection sensitivity characteristics of a seamless cylinder. In addition, the test article and test served as a technology demonstration to show the application of the flow forming manufacturing process to build more efficient buckling-critical structures by eliminating the welded joints that are traditionally used in the manufacturing of large metallic barrels. Pretest predictions of the cylinder buckling response were obtained using a finite-element model that included measured geometric imperfections. The buckling load predicted using this model was 697,000 lb, and the test article buckled at 743,000 lb (6% higher). After the test, the model was revised to account for measured variations in skin and stiffener geometry, nonuniform loading, and material properties. The revised model predicted a buckling load of 754,000 lb, which is within 1.5% of the tested buckling load. In addition, it was determined that the load carrying capability of the seamless cylinder is approximately 28% greater than a corresponding cylinder with welded joints.

Rudd, Michelle Tillotson↗
NASA NTRS1971

Pyrotechnic hazards classification and evaluation program. Run-up reaction testing in pyrotechnic dust suspensions

A preliminary investigation of the parameters included in run-up dust reactions is presented. Two types of tests were conducted: (1) ignition criteria of large bulk pyrotechnic dusts, and (2) optimal run-up conditions of large bulk pyrotechnic dusts. These tests were used to evaluate the order of magnitude and gross scale requirements needed to induce run-up reactions in pyrotechnic dusts and to simulate at reduced scale an accident that occurred in a manufacturing installation. Test results showed that propagation of pyrotechnic dust clouds resulted in a fireball of relatively long duration and large size. In addition, a plane wave front was observed to travel down the length of the gallery.

Source record↗