Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “large displacement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Magnetic forces in high-T(sub c) superconducting bearings

In September 1987 research at Cornell levitated a small rotor on superconducting bearing at 10,000 rpm. In April 1989 a speed of 120,000 rpm was achieved in a passive bearing with no active control. The bearing material used was YBa2Cu3O7. There is no evidence that the rotation speed has any significant effect on the lift force. Magnetic force measurements between a permanent rare-earth magnet and high T(sub c) superconducting material versus vertical and lateral displacements were made. A large hysteresis loop results for large displacements, while minor loops result for small displacements. These minor loops seem to give a slope proportional to the magnetic stiffness, and are probably indicative of flux pinning forces. Experiments of rotary speed versus time show a linear decay in a vacuum. Measurements of magnetic drag forces of a magnetic dipole over a high-T(sub c) superconducting disc of YBCO show that the drag force reaches a constant value, independent of the speed. Dampling of lateral vibrations of levitated rotors were measured which indicates that transverse flux motion in the superconductor will create dissipation. As a result of these force measurements, an optimum shape for the superconductor bearing pads which gives good lateral and axial stability was designed. Recent force measurements on melt-quench processed superconductors indicate a substantial increase in levitation force and magnetic stiffness over free sintered materials. As a result, application of high-T(sub c) superconducting bearings are beginning to show great promise at this time.

Moon, F. C.↗
NASA NTRS1990

Lateral restoring force on a magnet levitated above a superconductor

The lateral restoring force on a magnet levitated above a superconductor is calculated as a function of displacement from its original position at rest using Bean's critical-state model to describe flux pinning. The force is linear for small displacements and saturates at large displacements. In the absence of edge effects the force always attracts the magnet to its original position. Thus it is a restoring force that contributes to the stability of the levitated magnet. In the case of a thick superconductor slab, the origin of the force is a magnetic dipole layer consisting of positive and negative supercurrents induced on the trailing side of the magnet. The qualitative behavior is consistent with experiments reported to date. Effects due to the finite thickness of the superconductor slab and the granular nature of high-Tc materials are also considered.

Davis, L. C.↗
NASA NTRS1991

Magnetic forces in high-Tc superconducting bearings

In September 1987, researchers at Cornell levitated a small rotor on superconducting bearings at 10,000 rpm. In April 1989, a speed of 120,000 rpm was achieved in a passive bearing with no active control. The bearing material used was YBa2Cu307. There is no evidence that the rotation speed has any significant effect on the lift force. Magnetic force measurements between a permanent rare-earth magnet and high T(sub c) superconducting material versus vertical and lateral displacements were made. A large hysteresis loop results for large displacements, while minor loops result for small displacements. These minor loops seem to give a slope proportional to the magnetic stiffness, and are probably indicative of flux pinning forces. Experiments of rotary speed versus time show a linear decay in a vacuum. Measurements of magnetic dipole over a high-T(sub c) superconducting disc of YBCO show that the lateral vibrations of levitated rotors were measured which indicates that transverse flux motion in the superconductor will create dissipation. As a result of these force measurements, an optimum shape for the superconductor bearing pads which gives good lateral and axial stability was designed. Recent force measurements on melt-quench processed superconductors indicate a substantial increase in levitation force and magnetic stiffness over free sintered materials. As a result, application of high-T(sub c) superconducting bearings are beginning to show great promise at this time.

Moon, F. C.↗
NASA NTRS2015

Structural Characterization of Advanced Composite Tow-Steered Shells with Large Cutouts

The structural performance of two advanced composite tow-steered shells with large cutouts, manufactured using an automated fiber placement system, is assessed using both experimental and analytical methods. The fiber orientation angles of the shells vary continuously around their circumference from +/- 10 degrees on the crown and keel, to +/- 45 degrees on the sides. The raised surface features on one shell result from application of all 24 tows during each fiber placement system pass, while the second shell uses the tow drop/add capability of the system to achieve a more uniform wall thickness. These unstiffened shells, both without and with small cutouts, were previously tested in axial compression and buckled elastically. In this study, a single unreinforced cutout, scaled to represent a cargo door on a commercial aircraft, is machined into one side of each shell. The prebuckling axial stiffnesses and bifurcation buckling loads of these shells with large cutouts are also computed using linear finite element structural analyses for preliminary comparisons with test data. During testing, large displacements are observed around the large cutouts, but the shells maintain an average of 91 percent of the axial stiffness, and also carry 85 percent of the buckling loads, when compared to the pristine shells without cutouts. These relatively small reductions indicate that there is great potential for using tow steering to mitigate the adverse effects of large cutouts on the overall structural performance.

Wu, K. Chauncey↗
NASA NTRS1972

Ultraprecision tool positioner

A linear actuator was designed with a range of several centimeters plus. Two independently functioning devices were combined to form a tool positioner, which could be used for the generation of optical elements in highly stable materials or to actively control the figure of a lightweight astronomical mirror. The advantages of the positioner over other displacement actuators are: simplicity of construction, large displacement range, bidirectional displacement, and the ability to work against opposing forces. An engineering model positioner was manufactured and tested. The system includes an electronic switching circuit and a laser interferometer gage. It was demonstrated that, by combining a holding and a driving mechanism, the capabilities of a limited positioning device are extended.

Schmidt, E. E.↗
NASA NTRS1981

Room temperature shear properties of the strain isolator pad for the shuttle thermal protection system

Tests were conducted at room temperature to determine the shear properties of the strain isolator pad (SIP) material used in the thermal protection system of the space shuttle. Tests were conducted on both the .23 cm and .41 cm thick SIP material in the virgin state and after fifty fully reversed shear cycles. The shear stress displacement relationships are highly nonlinear, exhibit large hysteresis effects, are dependent on material orientation, and have a large low modulus region near the zero stress level where small changes in stress can result in large displacements. The values at the higher stress levels generally increase with normal and shear force load conditioning. Normal forces applied during the shear tests reduces the low modulus region for the material. Shear test techniques which restrict the normal movement of the material give erroneous stress displacement results. However, small normal forces do not significantly effect the shear modulus for a given shear stress. Poisson's ratio values for the material are within the range of values for many common materials. The values are not constant but vary as a function of the stress level and the previous stress history of the material. Ultimate shear strengths of the .23 cm thick SIP are significantly higher than those obtained for the .41 cm thick SIP.

Sawyer, J. W.↗
DOE OSTI2021

Combining cross-pivot flexures to generate improved kinematically equivalent flexure systems

In this work, we show that new kinematic equivalents with improved performance of standard flexure elements can be systematically synthesized by combination of cross-pivot flexures. Cross-pivot flexures provide a unique feature of kinematic stability under both high loading and large displacement conditions which can be exploited to synthesize a range of kinematic equivalents to standard flexure elements which retain much greater stiffness, load capacity and range capacity than the traditional elements. Cross-pivot synthetic elements provide a means to expand the performance of a large range of flexure-based structures including motion stages, manufacturing equipment and optical systems. This could result in better data collection, smaller systems, and less distortion in operation.

42 ENGINEERING↗
NASA NTRS2001

Controlling Fringe Sensitivity of Electro-Optic Holography Systems Using Laser Diode Current Modulation

Electro-Optic Holography (EOH) is a non-intrusive, laser-based, displacement measurement technique capable of static and dynamic displacement measurements. EOH is an optical interference technique in which fringe patterns that represent displacement contour maps are generated. At excessively large displacements the fringe density may be so great that individual fringes are not resolvable using typical EOH techniques. This thesis focuses on the development and implementation of a method for controlling the sensitivity of the EOH system. This method is known as Frequency Translated Electro-Optic Holography (FTEOH). It was determined that by modulating the current source of the laser diode at integer multiples of the object vibration, the fringe pattern is governed by higher order Bessel function of the first kind and the number of fringes that represent a given displacement can be controlled. The reduction of fringes is theoretically unlimited but physically limited by the frequency bandwidth of the signal generator, providing modulation to the laser diode. Although this research technique has been verified theoretically and experimentally in this thesis, due to the current laser diode capabilities it is a tedious and time consuming process to acquire data using the FTEOH technique.

Bybee, Shannon J.↗
NASA NTRS1982

Ion beamlet vectoring by grid translation

Ion beamlet vectoring is investigated by collecting deflection and divergence angle data for two-grid systems as a function of the relative displacement of these grids. Results show that at large displacements, accelerator grid impingement becomes a limiting factor and this determines the useful range of beamlet deflection. Beamlet deflection was shown to vary linearly with grid offset angle over this range. Values of deflection-to-offset angle ratio and useful range of deflection are presented as functions of grid-hole geometries, perveance levels, and accelerating voltages. It is found that the divergence of the beamlets is unaffected by deflection over the useful range of beamlet deflection. The grids of a typical dished-grid ion thruster are examined to determine where over the grid surface the grid offsets exceed the useful range, which indicates the regions on the surface where high accelerator grid impingment is probably occurring.

Homa, J. M.↗
NASA NTRS1984

Ion beamlet steering for two-grid electrostatic thrusters

An experimental study of ion beamlet steering in which the direction of beamlets emitted from a two grid aperture system is controlled by relative translation of the grids, is described. The results can be used to design electrostatic accelerating devices for which the direction and focus of emerging beamlets are important. Deflection and divergence angle data are presented for two grid systems as a function of the relative lateral displacement of the holes in these grids. At large displacements, accelerator grid impingements become excessive and this determines the maximum allowable displacement and as a result the useful range of beamlet deflection. Beamlet deflection is shown to vary linearly with grid offset angle over this range. The divergence of the beamlets is found to be unaffected by deflection over the useful range of beamlet deflection. The grids of a typical dished grid ion thruster are examined to determine the effects of thermally induced grid distortion and prescribed offsets of grid hole centerlines on the characteristics of the emerging beamlets. The results are used to determine the region on the grid surface where ion beamlet deflections exceed the useful range. Over this region high accelerator grid impingement currents and rapid grid erosion are predicted.

Homa, J. M.↗
DOE OSTI2022

Breaking of Inversion Symmetry and Interlayer Electronic Coupling in Bilayer Graphene Heterostructure by Structural Implementation of High Electric Displacement Fields

Controlling the interlayer coupling in two-dimensional (2D) materials generates novel electronic and topological phases. Its effective implementation is commonly done with a transverse electric field. However, phases generated by high displacement fields are elusive in this standard approach. Here, we introduce an exceptionally large displacement field by structural modification of a model system: AB-stacked bilayer graphene (BLG) on a SiC(0001) surface. We show that upon intercalation of gadolinium, electronic states in the top graphene layers exhibit a significant difference in the on-site potential energy, which effectively breaks the interlayer coupling between them. As a result, for energies close to the corresponding Dirac points, the BLG system behaves like two electronically isolated single graphene layers. This is proven by local scanning tunneling microscopy (STM)/spectroscopy, corroborated by density functional theory, tight binding, and multiprobe STM transport. Further, the work presents metal intercalation as a promising approach for the synthesis of 2D graphene heterostructures with electronic phases generated by giant displacement fields.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1987

Effect of axial impact on the static flexure of graphite/epoxy beams

Graphite-epoxy beams were subjected to an eccentric axial impact load in a drop tower test fixture in order to study their large displacement flexural behavior. The time history of the transient axial load exhibited a large magnitude occurring just after impact, which was many times greater than the static failure load. The damage caused by this peak dynamic load was measured by the reduction in energy absorption of the impacted beam relative to a virgin beam in static tests. For the thirty-ply specimens, the amount of damage increased with increasing axial stiffness.

Sensmeier, M. D.↗
NASA NTRS1988

Determination of convergence rates across the Ventura Basin, Southern California, using GPS and historical triangulation

Comparison of angles from historical triangulation observations dating as far back as 1932 with Global Positions System (GPS) measurements taken in 1987 indicates that rapid convergence may be taking place on decade timescales in the central and eastern part of the Ventura basin, an east-west trending trough bounded by thrust faults. Changes in angles over this time were analyzed using Prescott's modified Frank's method and in terms of a model which assumes that the regions to the north and south of the basin are rigid blocks undergoing relative motion. For the two block model, inversion of the observed angle changes over the last 28 years for the relative motion vector leads to north-south convergence across the basin of 30 + or - 5 mm/yr, with a left lateral component of 10 + or - 1 mm/yr in the Fillmore-Santa Paula area in the central part of the basin. The modified Frank's method yields strain rates of approximately 2 microrad/yr in both the east and central parts of the basin for measurements spanning the 1971 San Fernando earthquake. Assuming no east-west strain yeilds north-south compression of approximately 3.5 + or - .2 cm/yr. Comparison of triangulation data prior to the earthquake shows no strain outside the margin of error. The convergence rates determined by geodetic techniques are consistent with geologic observations in the area. Such large geodetic deformation rates, with no apparent near-surface creep on the major thrust, can be understood if these faults become subhorizontal at relatively shallow depths and if the subhorizontal portions of the faults are creeping. An alternative explanation of the large displacement rates might be that the pumping of oil in the vicinity of the benchmarks caused large horizontal motions, although it is unlikely that meter scale horizontal motions are due to oil withdrawal. These and other hypotheses are evaluated to better constrain the tectonics of this active region.

Donnellan, Andrea↗
NASA NTRS2004

Numerical and Experimental Dynamic Characteristics of Thin-Film Membranes

Presented is a total-Lagrangian displacement-based non-linear finite-element model of thin-film membranes for static and dynamic large-displacement analyses. The membrane theory fully accounts for geometric non-linearities. Fully non-linear static analysis followed by linear modal analysis is performed for an inflated circular cylindrical Kapton membrane tube under different pressures, and for a rectangular membrane under different tension loads at four comers. Finite element results show that shell modes dominate the dynamics of the inflated tube when the inflation pressure is low, and that vibration modes localized along four edges dominate the dynamics of the rectangular membrane. Numerical dynamic characteristics of the two membrane structures were experimentally verified using a Polytec PI PSV-200 scanning laser vibrometer and an EAGLE-500 8-camera motion analysis system.

Young, Leyland G.↗
NASA NTRS2001

Electroactive polymers as artificial muscles - reality and challenges

For many years, electroactive polymers (EAP) received reIatively little attention due to the small number of available materials and their limited actuation capability. The recent emergence of EAP materials with large displacement response changed the potential capability and paradigms of these materials. The main attractive characteristic of EAP is their operational similarity to biological muscles, particularly their resilience and ability to induce large actuation strains. Even though the actuation force of existing EAP materials and their robustness require further improvement, there has already been a series of reported successes. The successful applications that were demonstrated include catheter steering element, miniature manipulator, dust-wiper, miniature robotic arm, and grippers. Some of the currently considered applications may be difficult to accomplish and it is important to scope the requirements to the level that current materials can address. Using EAP to replace existing actuators may be a difficult challenge and therefore it is highly desirable to identify a niche application where it would not need to compete with existing capabilities. The application of these materials as actuators to drive various manipulation, mobility and robotic devices involves multidiscipline including materials, chemistry, electro-mechanics, computers, electronics, etc. This paper reviews the current efforts and the expectations for the future.

Bar-Cohen, Yoseph↗
NASA NTRS1994

Analysis of coseismic surface displacement gradients using radar interferometry: New insights into the Landers earthquake

The map of the coseismic displacement field generated by interferometric processing of synthetic aperture radar (SAR) images taken before and after the June 28, 1992, Landers earthquake sequence brings new insights into the nature of deformation caused by these earthquakes. We use the interferometric map generated by Massonnet et al. (1993) to analyze the surface displacement field in the vicinity of the fault trace. Complexities in the fringe pattern near the fault reflect short-wavelength variations of the surface rupture and slip distribution, and attest to large displacement gradients. Along two sections of the fault, characteristic fringe patterns can be recognized, contrasting in density and direction with patterns observed away from the rupture. In order to understand the observed fringe patterns, we compute synthetic interferograms in three simple cases: (1) rigid-body rotations about a vertical axis, (2) about a horizontal axis (tilt), and (3) distributed, simple shear. The orientation and spatial separation of interferometric fringes predicted by these models help constrain near-field deformation and rupture parameters. Where the Kickapoo fault connects with the Homestead Valley fault, the interferogram shows a clear pattern of parallel N20 deg W fringes separated by about 160 m. This pattern and vertical offsets measured along the Kickapoo fault suggest that the block between this fault and the Johnson Valley fault may have been tilted, down to the west. A 5-km block lifted by 1 m on one side would be tilted by an angle of 0.01 deg (190 microrad), producing fringes separated by about 160 m, parallel to the tilt axis. Such a tilt, parallel to a N20 deg W direction, would account for the gradual, northward increase of the vertical slip component observed along the Kickapoo fault. This tilt may also explain the 1 m of reverse slip observed along the 'slip gap' section of the Homestead Valley break. Between the southern end of the Johnson Valley fault and the Eureka Peak fault, where no surface rupture has been mapped, the dense pattern of fringes implies distributed shear, probably resulting from fault slip at depth. The density and direction of the fringes in the gap are consistent with a right-lateral slip of 1.2-3.8 m on a blind fault locked above the depth of 1.5-2 km. Such observations of small wavelength features in the SAR interferogram bring new insights into the near-field displacement gradient and thus on response of the uppermost crust to seismic rupture.

Peltzer, Gilles↗
NASA NTRS1993

Practical limits to the performance of magnetic bearings: Peak force, slew rate, and displacement sensitivity

Magnetic bearings are subject to performance limits which are quite different from those of conventional bearings. These are due in part to the inherent nonlinearity of the device and in part to its electrical nature. Three important nonideal behaviors are presented: peak force capacity, force slew rate limitation, and sensitivity to rotor motion at large displacements. The problem of identifying the dynamic requirements of a magnetic bearing when used to support a known structure subject to known loads is discussed in the context of these limitations. Several simple design tools result from this investigation.

Maslen, E.↗
NASA NTRS1994

A Large Motion Suspension System for Simulation of Orbital Deployment

This paper describes the design and implementation of a vertical degree of freedom suspension system which provides a constant force off-load condition to counter gravity over large displacements. By accommodating motions up to one meter for structures weighing up to 100 pounds, the system is useful for experiments which simulate the on-orbit deployment of spacecraft components. A unique aspect of this system is the combination of a large stroke passive off-load device augmented by electromotive torque actuated force feedback. The active force feedback has the effect of reducing breakaway friction by an order of magnitude over the passive system alone. The paper describes the development of the suspension hardware and the feedback control algorithm. Experiments were performed to verify the suspensions system's ability to provide a gravity off-load as well as its effect on the modal characteristics of a test article.

Straube, T. M.↗