Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interdigitated back contact”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Concepts for thin-film GaAs concentrator cells

The development of advanced GaAs concentrator solar cells, and in particular, the use of CLEFT (cleavage of lateral epitaxial films for transfer) processes for formation of thin-film structures is reported. The use of CLEFT has made possible processing of the back, and cells with back surface grids are discussed. Data on patterned junction development are presented; such junctions are expected to be useful in back surface applications requiring point contacts, grating structures, and interdigitated back contacts. CLEFT concentrator solar cells with grids on the front and back surfaces are reported here; these cells are 4 microns thick and are bonded to glass covers for support. Air mass zero efficiency of 18.8 percent has been obtained for a CLEFT concentrator operating at 18.5 suns.

Spitzer, M. B.↗
DOE OSTI2021

Effect of Dopant Compensation on the Conductivity of the Intrinsic poly-Si Isolation Region in Passivated IBC Silicon Solar Cells

The performance of IBC solar cells depends on the ability of this region to electrically isolate the doped fingers so that shunting does not occur and reduce the cell fill factor. We report on simulations which model the region between the p- and n-type poly-Si fingers of interdigitated back contact (IBC) solar cells as a series of resistors extending from one doped finger to the other. We demonstrate that the existence of a well compensated region between the doped fingers is enough to prevent shunting and loss of cell performance, despite contamination of dopants from the opposing dopant fingers. We show through these simulations that a net doping concentration below ~1018 cm-3 will enable a high resistivity and identify the conditions under which this highly resistive region forms despite imperfect finger edges. Additionally, we apply this analysis to tails measured by time-of-flight secondary ion mass spectrometry and confirm this hypothesis for our experimentally measured tails.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2022

Dopant Compensation within the Intrinsic Poly-Si Isolation Region in Poly-Si/SiOx Passivated IBC Si Solar Cells

We report on the effect of dopant compensation within intrinsic poly-Si regions between p- and n-type fingers of poly-Si/SiOx passivated interdigitated back contact (IBC) solar cells using intrinsic poly-Si as the isolation region between the doped poly-Si fingers. First, we show that dopants from the doped fingers contaminate the intrinsic gap, resulting in doping of the entire intrinsic gap and overlap of the dopant tails from each finger. Next, we show that despite this doping across the gap, shunting between the doped fingers does not occur. We show that this is a result of trap-assisted compensation creating a highly resistive intrinsic region, preventing shunt. We simulate shunt resistance across the gap based on local carrier concentration and deep trap density. We show that trap defects within the poly-Si enhance compensation between the dopant tails. We experimentally confirm these predictions by scanning spreading resistance microscopy of the gap showing ~20 um domain with resistivity ~10^7 ..omega.. cm. Additionally, Kelvin probe force microscopy are compared to finite element simulations which result in the same approximate shape for potential profile, indicating diode behavior across the isolation region. These results demonstrate the powerful effect that trap defects have within the poly-Si isolation region and suggest that precision patterning is not as essential as once thought.

dopant compensation↗
DOE OSTI2023

Self Assembled Monolayers for Passivated Contacts

Passivated contacts mitigate defects typically encountered due metallization of solar cells. We deposit amorphous silicon (a-Si:H) on an oxidized silicon wafer via PECVD and anneal at high temperature to crystallize into polysilicon passivated contact. One drawback is the absorption of the polysilicon between grid fingers, so removal of this material is desirable to maximize Jsc. Alternatively, interdigitated back contact cells rely on a gap between n- and p- fingers, which is commonly etched to ensure electronic isolation. We utilize a self assembled monolayer (SAM) using hexamethyldisilazane (HMDS) as a precursor to pattern and etch amorphous silicon (a-Si:H) and polysilicon without the need for photoresist. Ultraviolet light exposure oxidizes the HMDS by photocleaving the organic groups [1] of the SAM leaving a patterned SiO2. Directly soaking this in TMAH will eventually etch the SAM and the silicon, where the SiO2 serves as an etch mask. Inversely, a dilute HF dip selectively etches this SiO2 and the SAM remains. A subsequent soak in TMAH selectively etches the underlying silicon, where the SAM serves as an etch mask. Importantly, we find that the SAM can remain intact for metallization, where we measure 10 mO-cm2 specific contact resistivity on n-type polysilicon.

passivation↗
DOE OSTI2024

Ultraviolet Laser Activation of Phosphorus-Doped Polysilicon Layers for Crystalline Silicon Solar Cells

In crystalline silicon photovoltaics (c-Si PV), a pulsed laser can be used as a substitute for a high-temperature furnace dopant diffusion/activation step. In contrast to furnace-based activation, lasers can be used to achieve highly localized doping with controlled dopant concentrations, useful in advanced architectures such as the interdigitated back contact (IBC) solar cell. In this study, a pulsed ultraviolet (UV) laser is utilized for phosphorus dopant activation within a low-pressure chemical vapor deposited (LPCVD) polycrystalline silicon (poly-Si) passivated contact layer. The highest implied open-circuit voltage iV oc values achieved using this approach reach 726 mV. However, this comes at the expense of high specific contact resistivities ρ c , which is attributed to a lower dopant concentration across the poly-Si(n + )/SiO x /c-Si interface. Regardless, the optimum iV oc , ρ c combination is measured at a laser fluence of 0.78 J cm -2 producing values of 712 mV and 89 mΩ-cm 2 , respectively. These values are still compatible with high-efficiency solar cell designs, underscoring the feasibility and effectiveness of this approach.

14 SOLAR ENERGY↗
DOE OSTI2022

UV‐induced degradation of high‐efficiency silicon PV modules with different cell architectures

Abstract Degradation from ultraviolet (UV) radiation has become prevalent in the front of solar cells due to the introduction of UV‐transmitting encapsulants in photovoltaic (PV) module construction. Here, we examine UV‐induced degradation (UVID) in various commercial, unencapsulated crystalline silicon cell technologies, including bifacial silicon heterojunction (HJ), interdigitated back contact (IBC), passivated emitter and rear contact (PERC), and passivated emitter rear totally diffused (PERT) solar cells. We performed UV exposure tests using UVA‐340 fluorescent lamps at 1.24 W·m −2 (at 340 nm) and 45°C through 4.02 MJ·m −2 (2000 h). Our results showed that modern cell architectures are more vulnerable to UVID, leading to a significant power decrease (−3.6% on average; −11.8% maximum) compared with the conventional aluminum back surface field (Al‐BSF) cells (<−1% on average). The power degradation is largely caused by the decrease in short‐circuit current and open‐circuit voltage. A greater power decrease is observed in bifacial cells with rear‐side exposure compared with those with front‐side exposure, indicating that the rear side is more susceptible to UV damage. Secondary ion mass spectroscopy (SIMS) confirmed an increase in hydrogen concentration near the Si/passivation interface in HJ and IBC cells after UV exposure; the excess of hydrogen could result in hydrogen‐induced degradation and subsequently cause higher recombination losses. Additionally, surface oxidation and hot‐carrier damage were identified in PERT cells. Using a spectral‐based analysis, we obtained an acceleration factor of 5× between unpackaged cells (containing a silicon nitride antireflective coating on the front) in the UV test and an encapsulated module (with the front glass and encapsulant blocking 90% of the UV at 294 nm and 353 nm, respectively) in outdoor conditions. From the analytical calculations, we show that a UV‐blocking encapsulant can reduce UV transmission in the module by an additional factor of ~50.

14 SOLAR ENERGY↗
DOE OSTI2020

Electroluminescence Characterization of Recombination in Back Junction Silicon Heterojunction Test Structures: Role of the Inversion Layer

Electroluminescence (EL) characterization technique is used to quantify recombination properties in back junction silicon (Si) heterojunction (HJ) solar cell test structures with interdigitated back contact (IBC) emitters and metal contacts. These test structures are three terminal devices that allow the selective biasing and injection of minority carriers into spatially isolated emitter strips having different widths. This allows the study of minority carriers' current transport, flow, and recombination in these regions, which can, then, be applied to full IBC cells. EL is used to verify that emission is proportional to the minority carriers' concentration in the corresponding regions of the device, thus providing information relevant to minority carriers' collection when compared with laser beam induced current technique in considerably less time and with a higher spatial resolution. Current transport through the inversion layer that occurs due to the band bending at the n crystalline Si and p amorphous Si interface is discussed relying on the distance that minority carriers travel in different configurations and on their diffusion length. Laser defect spots (LDS) were, then, introduced in the emitter regions to analyze the spatial profile of minority carriers as they recombine at the LDS due to their high surface recombination velocity. Ideality factors in different configurations are spatially mapped from EL before and after introducing LDS and are used to show the effect of the inversion layer on the different recombination mechanisms. Current transport through the inversion layer is studied at different biasing conditions and correlated with current transport after LDS.

42 ENGINEERING↗
DOE OSTI2020

Understanding and Mitigating the Contamination of Intrinsic poly-Si Gaps in Passivated IBC Solar Cells

We investigate factors that are critical for the performance of interdigitated back contact (IBC) solar cells based on polycrystalline silicon (poly-Si) passivated contacts. During patterning of doped lines using direct plasma deposition through a shadow mask, we show that the intrinsic poly-Si gap becomes contaminated with dopants, leading to shunting. Possible contamination mechanisms during masked deposition and high- temperature annealing are tested. Strategies developed to mitigate the contamination, such as reactive ion etching after deposition and amorphous to poly-Si crystallization in oxygen, will lead to improved IBC fabrication methods.

14 SOLAR ENERGY↗
DOE OSTI2021

Assessing UV-Induced Degradation in Bifacial Modules of Different Cell Technologies

Bifacial technology enables solar cells to offer higher power output and lower levelized cost of energy compared to their monofacial counterparts. Here, we examined the adverse effects of ultraviolet-induced degradation (UVID) on a variety of high-efficiency silicon wafer-based bifacial cell technologies, including silicon heterojunction (SHJ), interdigitated back contact (IBC), passivated emitter rear contact (PERC), and passivated emitter rear totally-diffused (PERT). Both the front and rear sides of bifacial cells without any encapsulation were exposed to an artificially accelerated UV exposure test. After 2000 h of UV irradiation, the bifacial cells exhibited greater power loss with backside exposure indicating potential sensitivity of the rear passivation to UV. The highest power degradation is observed in SHJ cells, followed by p-PERC and n-PERT cell technologies. The degradation in SHJ cells is attributed to the reduction in V oc and FF, while the degradation in p-PERC and n-PERT cells is correlated with a significant drop in I sc . This suggests that each cell type/make degrades via different degradation pathways.

bifacial cells↗
DOE OSTI2020

Rapid Patterning and Advanced Device Structures for Low Cost Manufacturable Crystalline Si IBC Cells

Recent record efficiency Si cells have had an interdigitated back contact (IBC) design where both positive and negative contacts are fabricated on the back side of the Si wafer. Many industry groups have investigated IBC cells but used photolithography to pattern the rear contacts although it is considered impractical for low cost, high volume manufacturing. Alternative patterning methods using lasers and mechanical masking have been utilized in fabrication of patterned regions in IBC Si solar cells to replace photolithography. Another exciting advance in Si solar cell technology has been replacing the high temperature diffusion of doped regions inside the crystalline Si wafer with low temperature deposition of very thin layers of doped amorphous hydrogenated Si (a-Si:H) on the Si wafer. This is called a Si heterojunction (HJ) device. The a-Si:H provides excellent passivation of surface defects and has produced the highest open circuit voltages (VOC) of any Si solar cell device structure. The Institute of Energy Conversion (IEC) demonstrated the first IBC-HJ solar cell combining these two strategies in 2007 and has fabricated IBC-HJ cells with 20% efficiency using three photolithography steps. Despite the demonstrated efficiency potential of this device by industry groups (>26%) there is no commercial production because of the challenges of patterning and processing the structure in an industrial environment. Our work sought to address that challenge. The objective of this 3 year project was to develop the processing for the IBC-HJ Si solar cell using lasers for patterning and contact formation instead of photolithography. Laser patterning enables rapid, contactless manufacturing of patterned regions. We intensively studied laser fired contacts, laser patterning of the a-Si multi-layer stacks and metal layers and the use of plasma shadow masks. After an exhaustive focus in the first year on the laser fired emitter (LFE) and contact (LFC), we were unable to achieve VOC greater than 660 mV, compared to the 720 mV required to meet our milestones. We discovered that an additional issue with our original IBC structure was the presence of an inversion layer at the back surface connecting the p and n regions which reduced the VOC and fill factor (FF). We developed innovative methods for characterizing the inversion layer. These two limitations in the original design lead to development of a new IBC-HJ process sequence and device structure which we called Plasma Masked Laser Processed (PMLP). It retained the original high efficiency features including manufacturability. The LFC was replaced with a standard n-type a-Si HJ contact. The inversion layer was eliminated by replacing the previous p-type stack in the gap with an n-type or SiN stack. The PMLP used laser ablation of a multi-layer a-Si stack followed by chemical etching to open the n-contact. It required deposition of a patterned stack through a mask in the plasma deposition chamber. This turned out to be a source of significant problems due to inevitable unwanted deposition ‘leakage’ under the mask. This formed a blocking contact on the emitter which significantly reduced Voc and FF. Several iterations in PMLP device structure and chemical etching steps resulted in a large improvements, e.g. the efficiency increasing from 3 to 15% and Voc from 450 to 660 mV but they were unable to completely eliminate it. The best IBC-HJ device we fabricated had only 15% efficiency. For perspective, our standard FHJ devices had 20% efficiency.

14 SOLAR ENERGY↗
DOE OSTI2020

Impact of undoped substrates on high performance silicon solar cells

Today's highest-efficiency silicon solar cells typically operate near the threshold between low-level and high-level injection. It is not well understood if pushing further into a regime in which the cell operating point is solidly in high-level injection at all times of the day has further benefits for the solar cell performance. From a reliability perspective, cells fabricated on lower doped silicon have a larger breakdown voltage. This advantage can affect the design of modules allowing higher voltages and a relaxation of the number of bypass diodes needed. In this project, we present a comprehensive assessment, both experimental and using simulation, of how bulk resistivity, light intensity, and operation temperature impact the performance of the silicon solar cell. This work incorporates a comprehensive device physics analysis assisted by numerical simulation. The source code is now available under General Public License (GPL3), and to further leverage the findings of this project and outreach people outside of the scientific community, we are working with www.pveducation.org (which receives >1 million visitors a year) to create interactive content using our simulation results. The simulation results indicate that high bulk resistivity wafers (>>10 Ωcm) require bulk Shockley-Read-Hall (SRH) lifetimes in the millisecond range to outperform wafers with standard bulk resistivities (<10 Ωcm). Additionally, above bulk resistivities of 10 Ωcm (the exact value depends on the bulk characteristics of the wafer), the cell efficiency is weakly dependent on the bulk resistivity. As a result, ingot manufactures may have an opportunity to further reduce wafer cost by growing higher resistivity ingots that are more tolerant to resistivity variations. This project is particularly relevant today, as solar cell architectures with improved surface passivation and milliseconds lifetimes wafers are commercially available, leveraging potential benefits of using higher bulk resistivities. Outside of interdigitated back contact (IBC) cell, reported studies on high resistivity silicon (>100 Ωcm) are very limited. To the best of our knowledge, this project provides for the first-time experimental insight on solar cells fabricated on wafers with bulk resistivities up to several thousand Ωcm, delivering a comprehensive vision of their performance under real-world temperature and light intensity operation conditions. We manufactured and characterized solar cells with bulk resistivities in the range of 1 Ωcm to >15k Ωcm. Under standard testing conditions (STC), we measured solar cells efficiencies over 20% over the entire range of bulk resistivities, using our baseline cell processing. To evaluate the cell performance in real-world operation conditions, the solar cells were measured at different temperatures (25-80°C) and at different light intensities (0.1-1 suns). The measurements show that the bulk resistivity does not impact the solar cell response to temperature and light intensity. Similar thermal coefficients (TC) were measured for standard and high bulk resistivities, and they are comparable with the TC values reported in the literature for standard bulk resistivities <10 Ωcm. After light soaking, the solar cell didn’t show signs of light-induced degradation (LID). This result was expected since n-type float zone (FZ) wafers were used in this work, i.e. low traces of boron and low concentration of oxygen (oxygen is typically found in the seed end of Czochralski (CZ) ingots). We measured for high bulk resistivities (>10 Ωcm) extremely high breakdown voltages (>1000V). In conclusion, the insight provided by this project can positively impact the levelized cost of energy (LCOE) of the photovoltaic systems through its effect on cell and ingot manufacturing yield, silicon cell power output, and module reliability.

14 SOLAR ENERGY↗
DOE OSTI2023

Hybrid Tandem Photovoltaics

Tandem solar cell structures are the only strategy demonstrated to surpass the detailed balance efficiency limit of high-quality single-junction solar cells. To continue to improve the efficiencies of cost-effective terrestrial solar power, hybrid tandems of dissimilar subcells are being considered by many around the world, especially designs that incorporate silicon solar cells as a bottom subcell. In this project, we studied a wide variety of tandem design possibilities including those with three-terminal (3T) and four-terminal (4T) configurations. The use of 3T and 4T designs could be useful for efficient and economical hybrid tandem designs that utilize the best available subcell materials such as emerging perovskite materials. Three-terminal configurations, in particular, have not been sufficiently studied previously. We have laid the foundational groundwork in this project for understanding the operation of 3T tandems: developing a taxonomy for naming, a methodology for measuring and interconnecting, and models for simply characterizing 3T tandems. Electrical and optical subcell coupling between the subcells was also measured and modeled. An important part of this work was the fabrication of novel example tandem structures, including 4T GaAs/Si, 3T GaInP/Si, 3T GaAs/Si, and 3T GaInP/GaAs devices. Using these high-quality tandem cells, we have been able to clearly demonstrate the achievability of high-efficiencies, and subtle physical effects such as photon recycling and luminescent coupling. We have developed and demonstrated essential building-block tools such as transparent conductive adhesives (TCA) and 3T silicon bottom cells with interdigitated back contacts (IBC) that can also be used in many other tandem designs. We have tested the reliability of these tools and devices under standardized testing and outdoor measurements. We have found 4T GaAs/Si tandems to be relatively straightforward to fabricate and robust in real-world outdoor conditions. While we have demonstrated working hybrid 3T III-V/TCA/Si IBC tandems, we experienced low yields even with our best process flows yet. Further work is still needed to improve the processing yield of these devices. We therefore also created tandem cells using an all-III-V 3T tandem process which was very robust with high yields, allowing for the creation of voltage-matched strings in many different configurations using 8 nearly identical 3T tandems. Using these robust 3T tandem examples, we were able measure and precisely characterize 3T tandem behaviors to predict their operation under changing spectrum and temperature. The optoelectronic equivalent-circuit model was shown to be very general and applicable to hybrid tandems, and encompassed the operation 3T Si IBC cells. This general model has been distributed to the public in as open-source Python-based software called PVcircuit. We have calculated the implications of these new tandem device designs on the real-world energy production and shown how the relative performance of different tandem configurations is situational and can be engineered using the tools developed here.

14 SOLAR ENERGY↗
DOE OSTI2025

Enhancing lifetime, forecasting, and economic benefits of photovoltaic technologies undergoing UV-induced degradation with optical filtering

Ultraviolet-induced degradation (UV-ID) of various PV cell types was analyzed under optical UV filters with different cutoff wavelengths. Cell types studied included interdigitated back contact (IBC), passivated emitter and rear totally diffused (PERT), and heterojunction technology (HJT) based on crystalline Si (c-Si), and metal halide perovskite (MHP) cells. Analyzing degradation rates in two distinct regimes proved beneficial for all cell types. We used empirical linearizing functions ln(t) for c-Si technologies and 2 √t for MHP samples where t is time. These were applied to extrapolate UV-induced degradation over the lifetime of PV modules under various levels of optical UV filtering and used to predict the relative economic benefits for PV power plants. Degradation rates for all technologies were generally faster under the long pass optical filters having shorter cutoff wavelengths transmitting more UV irradiation and at elevated temperatures when testing MHP samples in the range between 60 °C and 90 °C.

14 SOLAR ENERGY↗
NASA NTRS1980

Planar multijunction high voltage solar cells

Technical considerations, preliminary results, and fabrication details are discussed for a family of high-voltage planar multi-junction (PMJ) solar cells which combine the attractive features of planar cells with conventional or interdigitated back contacts and the vertical multijunction (VMJ) solar cell. The PMJ solar cell is internally divided into many voltage-generating regions, called unit cells, which are internally connected in series. The key to obtaining reasonable performance from this device was the separation of top surface field regions over each active unit cell. Using existing solar cell fabricating methods, output voltages in excess of 20 volts per linear centimeter are possible. Analysis of the new device is complex, and numerous geometries are being studied which should provide substantial benefits in both normal sunlight usage as well as with concentrators.

Evans, J. C., Jr.↗
NASA NTRS1980

The planar multijunction cell - A new solar cell for earth and space

A new family of high-voltage solar cells, called the planar multijunction (PMJ) cell is being developed. The new cells combine the attractive features of planar cells with conventional or interdigitated back contacts and the vertical multijunction (VMJ) solar cell. The PMJ solar cell is internally divided into many voltage-generating regions, called unit cells, which are internally connected in series. The key to obtaining reasonable performance from this device was the separation of top surface field regions over each active unit cell area. Using existing solar cell fabricating methods, output voltages in excess of 20 volts per linear centimeter are possible. Analysis of the new device is complex, and numerous geometries are being studied which should provide substantial benefits in both normal sunlight usage as well as with concentrators.

Evans, J. C., Jr.↗
NASA NTRS1981

Coplanar back contacts for thin silicon solar cells

The type of coplanar back contact solar cell described was constructed with interdigitated n(+) and p(+) type regions on the back of the cell, such that both contacts are made on the back with no metallization grid on the front. This cell construction has several potential advantages over conventional cells for space use namely, convenience of interconnects, lower operating temperatures and higher efficiency due to the elimination of grid shadowing. However, the processing is more complex, and the cell is inherently more radiation sensitive. The latter problem can be reduced substantially by making the cells very thin (approximately 50 micrometers). Two types of interdigitated back contact cells are possible, the types being dependent on the character of the front surface. The front surface field cell has a front surface region that is of the same conductivity type as the bulk but is more heavily doped. This creates an electric field at the surface which repels the minority carriers. The tandem junction cell has a front surface region of a conductivity type that is opposite to that of the bulk. The junction thus created floats to open circuit voltage on illumination and injects carriers into the bulk which then can be collected at the rear junction. For space use, the front surface field cell is potentially more radiation resistant than the tandem junction cell because the flow of minority carriers (electrons) into the bulk will be less sensitive to the production of recombination centers, particularly in the space charge region at the front surface.

Storti, G.↗
DOE OSTI2021

Solar cell contacts: quantifying the impact of interfacial layers on selectivity, recombination, charge transfer, and V oc

Interfacial layers (IFLs) are ubiquitous in solar cells, but their precise impact on carrier transfer rates and the relation of these rates to performance metrics and the concepts of selectivity and recombination is lacking. We report the use of a well-defined interdigitated back-contact (IBC) silicon solar cell to determine the precise role of such IFLs. We characterize the action of the common IFL spiro-OMeTAD by making it a third contact to the IBC cell. This architecture creates three solar cells within a single structure that, with numerical simulation, provide the exchange current densities (i.e., charge transfer rates) for electrons ( J 0n ) and holes ( J 0p ) and the quasi Fermi-level splitting in the absorber, which measures the balance of generation and recombination. Further, we describe the relation of V oc to contact recombination, the asymmetry in electron/hole collection rates at a single contact (contact selectivity), and the asymmetry in collection rates of the same carrier at separate contacts (carrier selectivity). Relative to bare gold, neat spiro-OMeTAD reduces J 0n and J 0p (their geometric mean ( J 0n J 0p ) 0.5 decreases by 10 4 ), decreasing contact recombination. Addition of the common dopant Li-TFSI and air increase J 0p / J 0n by 10 6 with little effect on ( J 0n J 0p ) 0.5 , increasing contact hole selectivity. The significant increase in V oc observed by introducing spiro-OMeTAD/Li-TFSI IFLs into the cells studied, however, is due to an increase in the carrier selectivity rather than the contact selectivity or recombination of the spiro-OMeTAD-modified contact. Operando measurements further show voltage-dependent changes in the J 0 s, demonstrating that spiro-OMeTAD contributes to hysteresis. Broader context : Solar cells operate by photogenerating excess charge carriers in an absorber material and, in competition with recombination, asymmetrically extracting them at so-called carrier-selective contacts, one that ideally collects only electrons and the other, only holes. Particularly in emerging photovoltaics such as perovskites, thin layers of organic semiconductors or related materials are introduced between the absorber and contact to improve power conversion efficiency. In terms of interfacial charge transfer, a prevailing view is that such interfacial layers improve performance by helping block the collection of the undesired carrier, considered a form of recombination. We use a novel platform to study the simultaneous impact of spiro-OMeTAD, a common interfacial layer, on the collection of electrons, the collection of holes, and on the recombination of electrons and holes. We quantitatively demonstrate that spiro-OMeTAD layers indeed passivate the contact toward recombination, but that larger improvements in the open-circuit voltage, a key cell metric, can come not only from this but also from increasing the asymmetry of the collection of electrons in the system. Further, operando measurements show transient changes in the properties of spiro-OMeTAD which suggest that it contributes to hysteresis phenomena commonly observed in perovskite and other solar cells.

36 MATERIALS SCIENCE↗