Results for “inner layers” — Page 2

NASA NTRS1978

Self-sterilizing canister

Canister, originally conceived for remote sterilization of spacecraft packages, could be used terrestrially to handle samples in biologically hazardous environments. Multiwalled canister includes inner layer of pyrotechnic powder. For sterilization, electrically activated squib ignites powder, raising temperature of outer surface of canister to 230 degrees centigrade for several minutes. Thermal-buffer inner layer prevents inside temperature for exceeding 100 degrees centigrade to protect contents from damage. Samples in field hospitals and other emergency situations could also be handled by equipment.

Yang, L. C.↗

NASA NTRS1976

Laminar flow at a three-dimensional stagnation point with large rates of injection

Exact calculations of the titled flow are presented and compared to the predictions of an asymptotic analysis for large rates of injection. The inner layer of the boundary layer is found to involve outflow in both orthogonal directions whether the external flow along the y axis is inward or outward. As a result, the flow at a nearly two-dimensional stagnation point involves drastic changes as a weak outflow changes to a weak inflow. It is also found that the velocity profiles in the two directions in the inner layer are quite different.

Libby, P. A.↗

NASA NTRS1987

Rupture testing for the quality control of electrodeposited copper interconnections in high-speed, high-density circuits

Printed Wiring Multilayer Board (PWMLB) structures for high speed, high density circuits are prone to failure due to the microcracking of electrolytic copper interconnections. The failure can occur in the foil that makes up the inner layer traces or in the plated through holes (PTH) deposit that forms the layer to layer interconnections. It is shown that there are some distinctive differences in the quality of Type E copper and that these differences can be detected before its use in a PWMLB. It is suggested that the strength of some Type E copper can be very low when the material is hot and that it is the use of this poor quality material in a PWMLB that results in PTH and inner layer microcracking. Since the PWMLB failure in question are induced by a thermal stress, and since the poorer grades of Type E materials used in these structures are susceptible to premature failure under thermal stress, the use of elevated temperature rupture and creep rupture testing is proposed as a means for screening copper foil, or its PTH equivalent, in order to eliminate the problem of Type E copper microcracking in advanced PWMLBs.

Zakraysek, Louis↗

NASA NTRS2019

Fatigue Behavior of Coated Titanium Alloys

Advanced multi-component TiAlCrTaSiN-based multilayered coatings were developed and processed onto Ti-6Al-4V (Ti-6-4) and GammaMet PX (GMPX or TiAl) alloys by a magnetron-enhanced physical vapor deposition technique. The coatings have recently been in development with the goal of improving advanced titanium alloy, turbine engine component durability and oxidation-erosion resistance. In this work, the performance of the multi-component coating system (including the outer layer nitride based coating and inner TiAlCrSi oxidation barrier bond coat) was studied, and the coating's influence on the fatigue behavior of the titanium-based alloys were compared. Although the multi-component coating was initially optimized to improve the coating's high temperature oxidation and erosion resistance, the lower ductility nitride-based coating needs further work on microstructure or composition to improve its mechanical stress resistance and strain tolerance for use in cyclically loaded, turbine blade operating conditions. This is particularly true for GMPX and other γ-TiAl alloys because these intermetallic titanium alloys have limited ductility and are very sensitive to defects such as coating cracks. However, the inner layer TiAlCrSi-coating had better adhesion and ductility, and may be a suitable choice to improve the oxidation resistance of titanium alloys.

Oxidation Barrier Coatings↗

NASA NTRSDate not supplied

A Survey of ISS and Visiting Vehicle Returned Surfaces for Environmental Characterization and Computer Model Development

The Orbital Debris Engineering Model (ORDEM) developed by the NASA Orbital Debris Program Office (ODPO) is a data-driven model — extensive radar, optical, laboratory, and in situ measurement data sets have been used to build the model since its earliest versions. A salient aspect of professional software development is the verification and validation (V&V) process. Verification answers the question “Is the model built correctly?” while validation addresses the question “Did we build the correct model?” Less extensive, reserved, or independent data sets serve the validation requirement. Due to the dynamic nature of the orbital debris environment, it is critical to use contemporaneous data sources that represent the current environment to support ORDEM development and validation. ORDEM has utilized in situ data collected from Space Shuttle and Hubble Space Telescope surface inspections, now over a decade old. This historical dataset is fundamental for providing baseline in situ measurement data for sizes between 10 to 300 microns, but new data sources are being evaluated using returned surfaces from or near the International Space Station (ISS). This paper reviews a general microscopic survey of ISS soft goods, the Pressurized Mating Adapter 2 (PMA-2) blanket, and a limited-scope feasibility study conducted on the Space Exploration Technologies Corporation (SpaceX) Dragon capsule’s Thermal Protection System (TPS) material. The PMA-2 blanket, exposed to the space environment between 09 July 2013 and 25 February 2015, is an approximately 3.7 m2-area blanket composed of a betacloth outer layer and multiple ballistic fabric inner layers. The SpaceX Cargo Dragon capsule regularly visited the ISS from 2012 through 2020 and potentially provides a timely and well-characterized source of data for modeling purposes. The capsule’s lateral surfaces use SpaceX Proprietary Ablative Material (SPAM) TPS material, a syntactic foam, for thermal management during all mission phases. Seven SPAM extracted samples have been analyzed to date. This paper will provide an overview of the characterization completed for impact features by size, depth, impactor diameter, and the impactor residues chemical analyses, allowing a differentiation between micrometeoroids and orbital debris and a categorization by mass density and density class. Impactor diameter is estimated using damage equations generated from ground-based hypervelocity impact testing. The orbital debris impactors are compared to the current ORDEM 3.2 model of the environment at ISS altitudes. We briefly discuss the meteoroid impactors, including constituents and mass densities, in the general context of current models.

Phillip Anz-meador↗

NASA NTRSDate not supplied

A Survey of ISS and Visiting Vehicle Returned Surfaces for Environmental Characterization and Computer Model Development

The Orbital Debris Engineering Model (ORDEM) developed by the NASA Orbital Debris Program Office (ODPO) is a data-driven model — extensive radar, optical, laboratory, and in situ measurement data sets have been used to build the model since its earliest versions. A salient aspect of professional software development is the verification and validation (V&V) process. Verification answers the question “Is the model built correctly?” while validation addresses the question “Did we build the correct model?” Less extensive, reserved, or independent data sets serve the validation requirement. Due to the dynamic nature of the orbital debris environment, it is critical to use contemporaneous data sources that represent the current environment to support ORDEM development and validation. ORDEM has utilized in situ data collected from Space Shuttle and Hubble Space Telescope surface inspections, now over a decade old. This historical dataset is fundamental for providing baseline in situ measurement data for sizes between 10 to 300 microns, but new data sources are being evaluated using returned surfaces from or near the International Space Station (ISS). This paper reviews a general microscopic survey of ISS soft goods, the Pressurized Mating Adapter 2 (PMA-2) blanket, and a limited-scope feasibility study conducted on the Space Exploration Technologies Corporation (SpaceX) Dragon capsule’s Thermal Protection System (TPS) material. The PMA-2 blanket, exposed to the space environment between 09 July 2013 and 25 February 2015, is an approximately 3.7 m2-area blanket composed of a betacloth outer layer and multiple ballistic fabric inner layers. The SpaceX Cargo Dragon capsule regularly visited the ISS from 2012 through 2020 and potentially provides a timely and well-characterized source of data for modeling purposes. The capsule’s lateral surfaces use SpaceX Proprietary Ablative Material (SPAM) TPS material, a syntactic foam, for thermal management during all mission phases. Seven SPAM extracted samples have been analyzed to date. This paper will provide an overview of the characterization completed for impact features by size, depth, impactor diameter, and the impactor residues chemical analyses, allowing a differentiation between micrometeoroids and orbital debris and a categorization by mass density and density class. Impactor diameter is estimated using damage equations generated from ground-based hypervelocity impact testing. The orbital debris impactors are compared to the current ORDEM 3.2 model of the environment at ISS altitudes. We briefly discuss the meteoroid impactors, including constituents and mass densities, in the general context of current models.

Phillip Anz-Meador↗

NASA NTRS1989

TBCs for better engine efficiency

State-of-the-art thermal barrier coatings (TBCs) developed for aircraft engines can achieve both hot-section component operating temperature reductions and superior oxidation resistance. Such TBCs typically consist of two layers: a metallic, often NiCrAlY 'bond' inner layer in contact with the superalloy structural component, and an outer, insulating ceramic layer. A ceramic frequently used in this role due to its high durability is plasma-sprayed ZrO2, partially stabilized with 6-8 wt pct Y2O3. TBCs can also be useful in nonaircraft gas turbines, which frequently use highly contaminated fuels.

Brindley, William J.↗

NASA NTRS1992

Role of Si2N2O in the passive oxidation of chemically-vapor-deposited Si3N4

The results of two-step oxidation experiments on chemically-vapor-deposited Si3N4 and SiC at 1350 C show that a correlation exists between the presence of a Si2N2O interphase and the strong oxidation resistance of Si3N4. During normal oxidation, k sub p for SiC was 15 times higher than that for Si3N4, and the oxide scale on Si3N4 was found by SEM and TEM to contain a prominent Si2N2O inner layer. However, when oxidized samples are annealed in Ar for 1.5 h at 1500 C and reoxidized at 1350 C as before, three things happen: the oxidation k sub p increases over 55-fold for Si3N4, and 3.5-fold for SiC; the Si3N4 and SiC oxidize with nearly equal k sub p's; and, most significantly, the oxide scale on Si3N4 is found to be lacking an inner Si2N2O layer. The implications of this correlation for the competing models of Si3N4 oxidation are discussed.

Ogbuji, Linus U. J. T.↗

NASA NTRS1974

Investigation of the oxidation behavior of dispersion stabilized alloys when exposed to a dynamic high temperature environment

The oxidation behavior of TD-NiCr and TD-NiCrAlY alloys have been studied at 2000 and 2200 F in static and high speed flowing air environments. The TD-NiCrAlY alloys preoxidized to produce an Al2O3 scale on the surface showed good oxidation resistance in both types of environments. The TD-NiCr alloy which had a Cr2O3 oxide scale after preoxidation was found to oxidize more than an order of magnitude faster under the dynamic test conditions than at comparable static test conditions. Although Cr2O3 normally provides good oxidation protection, it was rapidly lost due to formation of volatile CrO3 when exposed to the high speed air stream. The preferred oxide arrangement for the dynamic test consisted of an external layer of NiO with a porous mushroom type morphology, an intermediate duplex layer of NiO and Cr2O3, and a continuous inner layer of Cr2O3 in contact with the alloy substrate. An oxidation model has been developed to explain the observed microstructure and overall oxidation behavior of all alloys.

Tenney, D. R.↗

NASA NTRS1995

Preliminary results of the on-demand vortex-generator experiments

This is a report on the continuation of our experimental investigations (Saddoughi 1994) of 'on-demand' vortex generators. Conventional vortex generators as found on aircraft wings are mainly for suppression of separation during the off-design conditions. In cruise they perform no useful function and exert a significant drag penalty. Therefore, replacement of fixed rectangular or delta-wing generators by devices that could be activated when needed would be of interest. Also in our previous report, we described one example of an 'on-demand' device, which was developed by Jacobson & Reynolds (1995) at Stanford University, suitable for manufacture by micro-electro-mechanical technology. This device consists of a surface cavity elongated in the stream direction and covered with a lid cantilevered at the upstream end. The lid, which is a metal sheet with a sheet of piezoelectric ceramic bonded to it, lies flush with the boundary. On application of a voltage the ceramic expands or contracts; however, adequate amplitude can be obtained only by running at the cantilever resonance frequency and applying amplitude modulation: for 2.5 mm x 20 mm cantilevered lids, they obtained maximum tip displacements of the order of 100 pm. Thus fluid is expelled from the cavity through the gap around the lid on the downstroke. They used an asymmetrical gap configuration and found that periodic emerging jets on the narrow side induced periodic longitudinal vorticity into the boundary layer. Their device was used to modify the inner layer of the boundary layer for skin-friction reduction. The same method could be implemented for the replacement of the conventional vortex generators; however, to promote mixing and suppress separation we needed to deposit longitudinal vortices into the outer layer of the boundary layer, which required a larger vortex generator than the device built by Jacobson & Reynolds. Our vortex generator was built with a mechanically-driven cantilevered lid with an adjustable frequency. The device was made about ten times the size of Jacobson & Reynolds', the shape or size of the cavity and lid (28 mm x 250 mm) could be easily changed. The cavity depth, the cantilever-tip displacement, and the maximum lid frequency were 20 mm, 10 mm, and 60 Hz respectively. Our vortex generator was mounted on a turntable so that its yaw angle could be changed. Finally, tests over a range of ratios of vortex generator size to boundary-layer thickness could be carried out simply by changing the streamwise location of the device.

Saddoughi, Seyed G.↗

NASA NTRS2017

Testing Seam Concepts for Advanced Multilayer Insulation

Multilayer insulation (MLI) is considered the state of the art insulation for cryogenic propellant tanks in the space environment. MLI traditionally consists of multiple layers of metalized films separated by low conductivity spacers. In order to better understand some of the details within MLI design and construction, GRC has been investigating the heat loads caused by multiple types of seams. To date testing has been completed with 20 layer and 50 layer blankets. Although a truly seamless blanket is not practical, a blanket lay-up where each individual layer was overlapped and tapped together was used as a baseline for the other seams tests. Other seams concepts tested included: an overlap where the complete blanket was overlapped on top of itself; a butt joint were the blankets were just trimmed and butted up against each other, and a staggered butt joint where the seam in the out layers is offset from the seam in the inner layers. Measured performance is based on a preliminary analysis of rod calibration tests conducted prior to the start of seams testing. Baseline performance for the 50 layer blanket showed a measured heat load of 0.46 Watts with a degradation to about 0.47 Watts in the seamed blankets. Baseline performance for the 20 layer blanket showed a measured heat load of 0.57 Watts. Heat loads for the seamed tests are still begin analyzed. So far analysis work has suggested the need for corrections due to heat loads from both the heater leads and the instrumentation wires. A careful re-examination of the calibration test results with these factors accounted for is also underway. This presentation will discuss the theory of seams in MLI, our test results to date, and the uncertainties in our measurements.

multilayer insulation↗

NASA NTRS1982

Trichite growth during oxidation of titanium and TA6V4 alloy by water vapor at high temperatures

Analysis by electron scanning microscope detected the formation of rutile trichites on the surface of specimens of titanium and titanium alloy TA6V4 oxidized in water vapor in the temperature range 650 to 950 C and the water vapor pressure range from 0.5 to 18 torr. In all specimens, two sublayers of rutile were formed: an external layer of basalt-like appearance, and a microcrystalline inner layer. Morphology of the trichites depends on temperature and the material (whether metal or alloy), but not on vapor pressure.

Coddet, C.↗

NASA NTRS1991

The symmetric turbulent plane wake downstream of a sharp trailing edge

The analysis and modeling of the symmetric turbulent plane wake downstream of a sharp trailing edge is addressed. A compact description of the flow near the trailing edge is formulated using the results of a previous asymptotic analysis. The new description retains the two-layered structure identified in the previous work, and it clarifies the principal dynamics of the flow in the near-wake outer layer, away from the wake centerline. For zero-pressure-gradient flow, the near-wake outer layer is shown to be represented to leading order by the similarity solution that governs the outer region of the surface boundary layer. The leading perturbation in the outer layer due to the developing near-wake inner-layer flow is identified, and this is shown to be asymptotically smaller than undetermined higher-order terms associated with the surface boundary-layer flow. Results of the new near-wake analysis are used to formulate an algebraic eddy viscosity model for wake flow predictions at arbitrary distances from the trailing edge. The model is used in a numerical solution of the boundary layer equations, and computed velocity and Reynolds stress profiles are shown to compare well with experimental data.

Bogucz, E. A.↗

NASA NTRS1983

Cooling Vest

Because quadriplegics are unable to perspire below the level of spinal injury, they cannot tolerate heat stress. A cooling vest developed by Ames Research Center and Upjohn Company allows them to participate in outdoor activities. The vest is an adaptation of Ames technology for thermal control garments used to remove excess body heat of astronauts. The vest consists of a series of corrugated channels through which cooled water circulates. Its two outer layers are urethane coated nylon, and there is an inner layer which incorporates the corrugated channels. It can be worn as a backpack or affixed to a wheelchair. The unit includes a rechargeable battery, mini-pump, two quart reservoir and heat sink to cool the water.

Source record↗

NASA NTRS2003

Oxide Protective Coats for Ir/Re Rocket Combustion Chambers

An improved material system has been developed for rocket engine combustion chambers for burning oxygen/ hydrogen mixtures or novel monopropellants, which are highly oxidizing at operating temperatures. The baseline for developing the improved material system is a prior iridium/rhenium system for chambers burning nitrogen tetroxide/monomethyl hydrazine mixtures, which are less oxidizing. The baseline combustion chamber comprises an outer layer of rhenium that provides structural support, plus an inner layer of iridium that acts as a barrier to oxidation of the rhenium. In the improved material system, the layer of iridium is thin and is coated with a thermal fatigue-resistant refractory oxide (specifically, hafnium oxide) that serves partly as a thermal barrier to decrease the temperature and thus the rate of oxidation of the rhenium. The oxide layer also acts as a barrier against the transport of oxidizing species to the surface of the iridium. Tests in which various oxygen/hydrogen mixtures were burned in iridium/rhenium combustion chambers lined with hafnium oxide showed that the operational lifetimes of combustion chambers of the improved material system are an order of magnitude greater than those of the baseline combustion chambers.

Fortini, Arthur↗

NASA NTRS1975

Dynamic oxidation behavior of TD-NiCr alloy with different surface pretreatments

Oxidation tests of TD-NiCr alloy with different surface pretreatments were conducted in a Mach-5 arc-jet at 1200 C and 0.002 lb/sec flowing air environment. The mechanisms responsible for the observed oxidation behavior are examined. The presence of atomic oxygen in the air stream plays a significant role in determining the oxidation characteristic of the alloy. The rate of Cr2O3 vaporization by formation of volatile CrO3 is greatly enhanced by the flowing conditions. The typical microstructure of oxides formed in the dynamic tests consists of an external layer of NiO with a porous mushroom-type morphology, an intermediate layer of NiO and Cr2O3 oxide mixture, and a continuous inner layer of Cr2O3 in contact with the Cr-depleted alloy substrate. Three basic processes underlying the formation of mushroom-type NiO are identified and discussed. The oxidation rate is determined by the rate of vaporization of NiO. Surface pretreatment has a significant effect on the oxidation behavior of the alloy in the early stage of oxidation, but becomes less important as exposure time increases. Mechanical polishing induces surface recrystallization, but promotes the concurrence of external growth of NiO and internal oxidation of the alloy in the dynamic atmosphere.

Young, C. T.↗

NASA NTRS1985

Mechanisms of thermal barrier coating degradation and failure

The objectives and initial results of a Thermal Barrier Coating (TBC) Life Prediction Model Development Program are described. The goals of this program are to: identify and understand TBC failure modes; generate quantitative TBC life data; and develop and verify a TBC life prediction model. The coating being studied is a two layer thermal barrier system incorporating a nominal ten mil outer layer of seven percent yttria partially stabilized zirconia plasma deposited over an inner layer of highly oxidation resistant low pressure plasma sprayed NiCrAlY bond coating. This coating currently is in flight service on turbine vane platforms in the JT-9D and PW2037 engines and is bill-of- material on turbine vane airfoils in the advanced PW4000 and IAE V2500 engines. Effort currently is in progress on the first task, which involves the identification and understanding of TBC failures. Five modes of coating damage were considered: thermomechanical ceramic failure; oxidative bond coat failure; hot corrosion; foreign object damage (FOD); and erosion.

Demasi, J. T.↗

NASA NTRS2000

Hubble Space Telescope Thermal Blanket Repair Design and Implementation

Substantial damage to the outer layer of Hubble Space Telescope (HST) thermal blankets was observed during the February 1997 servicing mission. After six years in LEO, many areas of the aluminized Teflon(R) outer blanket layer had significant cracks, and some material was peeled away to expose inner layers to solar flux. After the mission, the failure mechanism was determined, and repair materials and priorities were selected for follow-on missions. This paper focuses on the thermal, mechanical, and EVA design requirements for the blanket repair, the creative solutions developed for these unique problems, hardware development, and testing.

Ousley, Wes↗