Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “impurity concentration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Low cost silicon solar array project silicon materials task: Establishment of the feasibility of a process capable of low-cost, high volume production of silane (step 1) and the pyrolysis of silane to semiconductor-grade silicon (step 2)

A quartz fluid bed reactor capable of operating at temperatures of up to 1000 C was designed, constructed, and successfully operated. During a 30 minute experiment, silane was decomposed within the reactor with no pyrolysis occurring on the reactor wall or on the gas injection system. A hammer mill/roller-crusher system appeared to be the most practical method for producing seed material from bulk silicon. No measurable impurities were detected in the silicon powder produced by the free space reactor, using the cathode layer emission spectroscopic technique. Impurity concentration followed by emission spectroscopic examination of the residue indicated a total impurity level of 2 micrograms/gram. A pellet cast from this powder had an electrical resistivity of 35 to 45 ohm-cm and P-type conductivity.

Breneman, W. C.↗
NASA NTRS1973

Sensitivity and fatigue of LiTaO3 for holographic recording

The sensitivity of crystals of LiTaO3 to hologram formation was observed to vary with impurity concentration from a value comparable to the most sensitive doped LiNbO3 for an impure crystal to a value more than five orders of magnitude smaller for a purer crystal. Fatigue effects were observed upon write-erase cycling. These effects were dependent upon writing and erasure polarization and power and could be virtually eliminated by proper choice of optical parameters.

Spinhirne, J. M.↗
NASA NTRS2005

Impurity Studies of Cd(0.8)Zn(0.2)Te Crystals Using Photoluminescence and Glow Discharge Mass Spectroscopy

Cd(1-x)Zn(x)Te semiconductor crystal is a highly promising material for room temperature x- and gamma-ray detector applications because of its high resistivity, long carrier lifetime, and relatively high hole and electron mobilities. This paper reports the investigation of the impurities in several Cd(1-x)Zn(x)Te (x = 0.20) crystals grown using the vertical Bridgman method under a Cd overpressure. The impurity concentrations were measured using glow discharge mass spectroscopy (GDMS). The energy states of the impurities were studied using photoluminescence (PL) spectroscopy at liquid helium temperature. The PL spectra showed a series of sharp high energy lines which are associated with free excitons and excitons bound to impurities as donors and acceptors in the crystals. The impurities also contributed to donor-acceptor pair recombination. The correlation between the GDMS and PL results will be reported.

Su, Ching-Hua↗
NASA NTRS2000

Direct Visualization of an Impurity Depletion Zone

When a crystal incorporates more impurity per unit of its volume than the impurity concentration in solution, the solution in vicinity of the growing crystal is depleted with respect to the impurity I,2. With a stagnant solution, e. g. in microgravity or gels, an impurity depletion zone expands as the crystal grows and results in greater purity in most of the outer portion of the crystal than in the core. Crystallization in gel provides an opportunity to mimic microgravity conditions and visualize the impurity depletion zone. Colorless, transparent apoferritin (M congruent to 450 KDa) crystals were grown in the presence of red holoferritin dimer as a microheterogeneous impurity (M congruent to 900 KDa) within agarose gel by counterdiffusion with Cd(2+) precipitant. Preferential trapping of dimers, (distribution coefficient K = 4 (exp 1,2)) results in weaker red color around the crystals grown in the left tube in the figure as compared to the control middle tube without crystals. The left and the middle tubes contain colored ferritin dimers, the right tube contains colored trimers. The meniscus in the left tube separate gel (below) and liquid solution containing Cd(2+) (above). Similar solutions, though without precipitants, were present on top of the middle and right tube allowing diffusion of dimers and trimers. The area of weaker color intensity around crystals directly demonstrates overlapped impurity depletion zones.

Chernov, Alex A.↗
NASA NTRS1984

Ice-Soil Mixtures: Visual and Near-Infrared Remote Sensing Techniques

The spectral properties of ice soil mixtures are reviewed. Water ice has an absorption coefficient which varies by several orders of magnitude in the visual and near infrared, and has several prominent overtone absorptions. Different wavelengths can be used to probe to different depths in the surface as well as for different mineral impurity concentrations. Empirical and/or theoretical models might be used to derive characteristics grain size of the ice or of the impurity minerals and to derive abundance of the ice and rock or soil components. Quantitative analysis of remotely obtained reflectance spectra can only be performed by using absorption features in the spectra of ice and soil, and not by broadband response. It is suggested that this might be done by special selection of several narrow band filters in the near infrared which will adequately define the ice absorptions.

Clark, R. N.↗
NASA NTRS1985

Theoretical Studies of the Surface Tension of Liquid Metal System

A major goal of this project is to understand the surface tension and other thermophysical properties of liquid metals and alloys from a fundamental viewpoint. The approach is to calculate these quantities by a first principles technique which combines the statistical-mechanical theory of the liquid state with an electronic pseudopotential theory of electrons in metals. The inhomogeneity of the surface is treated using an ionic-density-functional formalism developed with the support of NASA. Of particular interest are the variation of surface tension with temperature and impurity concentration: such variations strongly influence the types of convection which make take place in a low-gravity environment. Some progress has already been achieved in computing the reduction of surface tension due to the presence of low-surface-tension impurities, and the corresponding surface segregation of such impurities. In the coming year, it is planned to concentrate on the surface properties of materials of particular interest to the MSA program: Si, Ga and GaSn alloys. An additional goal is to gain some theoretical understanding of the high temperature thermophysical properties of liquid metals, particularly high melting point materials which have not been studied extensively from a theoretical viewpoint.

Stroud, D. G.↗
NASA NTRS1979

Low cost processes for silicon

The paper describes the multiple process development of low cost processes for manufacture of silicon. A support program includes subtasks for the modeling of reactions and reactors, chemical engineering and solid-state physics studies, and development of impurity concentration measurement procedures. The preliminary economic analyses indicate total product costs ranging from $5.00 to $8.73/kg based on 1000 MT/yr plants. In the studies of impurity effects, a model which considers that degradations of solar cell performance by impurities are primarily due to decreases in base diffusion length was constructed from experimental data.

Lutwack, R.↗
NASA NTRS2011

Influence of Dust and Black Carbon on the Snow Albedo in the NASA Goddard Earth Observing System Version 5 Land Surface Model

Present-day land surface models rarely account for the influence of both black carbon and dust in the snow on the snow albedo. Snow impurities increase the absorption of incoming shortwave radiation (particularly in the visible bands), whereby they have major consequences for the evolution of snowmelt and life cycles of snowpack. A new parameterization of these snow impurities was included in the catchment-based land surface model used in the National Aeronautics and Space Administration Goddard Earth Observing System version 5. Validation tests against in situ observed data were performed for the winter of 2003.2004 in Sapporo, Japan, for both the new snow albedo parameterization (which explicitly accounts for snow impurities) and the preexisting baseline albedo parameterization (which does not). Validation tests reveal that daily variations of snow depth and snow surface albedo are more realistically simulated with the new parameterization. Reasonable perturbations in the assigned snow impurity concentrations, as inferred from the observational data, produce significant changes in snowpack depth and radiative flux interactions. These findings illustrate the importance of parameterizing the influence of snow impurities on the snow surface albedo for proper simulation of the life cycle of snow cover.

Yasunari, Teppei J.↗
NASA NTRS1981

Spectral albedos of midlatitude snowpacks

Spectral albedos of impure-nonhomogeneous snowpacks, typical of midlatitudes, from 400 to 2200 nm were modeled through a numerical solution of the radiative transfer equation in the two-stream approximation. Discrete depth-dependent values of density, grain size and impurity concentration were used to characterize the snowpacks. The model is for diffuse incident radiation, and the numerical method is based on doubling and invariant imbedding. The effect of soot impurities on snowpack albedos is illustrated when a snowpack is several centimeters deep and soot reduces the albedos at visible wavelengths, however, when a snowpack is only a few centimeters deep, soot may increase the albedos at visible wavelengths. By adjusting soot content and snow grain size, good quantitative agreement with some observations at the Cascade Mountains (Washington) and at Point Barrow (Alaska) are obtained; however, the model grain sizes are found to be fifty to four hundred percent larger than the measured values. For satellite snowcover observations, a model for effective albedo of partially snow-covered areas was developed and compared with some NOAA-2 observations of the southeastern United States.

Choudhury, B.↗
NASA NTRS1974

Sensitivity and fatigue of LiTaO3 for holographic recording

The sensitivity of LiTaO3 crystals to hologram formation has been observed to vary with impurity concentration. For a writing wavelength of 488.0 nm and power density of 1.1 W/sq cm, the sensitivity varied from a value comparable to the most sensitive doped LiNbO3 for an impure crystal to a value more than 5 orders of magnitude smaller for a purer crystal. Fatigue effects were observed upon write-erase cycling. These effects were dependent upon writing and erasure polarization and power density and could be minimized by proper choice of optical parameters.

Spinhirne, J. M.↗
NASA NTRS1998

Advanced far infrared blocked impurity band detectors based on germanium liquid phase epitaxy

This research has shown that epilayers with residual impurity concentrations of 5 x 10(sup 13) cm(exp -3) can be grown by producing the purest Pb available in the world. These epilayers have extremely low minority acceptor concentrations, which is ideal for fabrication of IR absorbing layers. The Pb LPE growth of Ge also has the advantageous property of gettering Cu from the epilayer and the substrate. Epilayers have been grown with intentional Sb doping for IR absorption on lightly doped substrates. This research has proven that properly working Ge BIB detectors can be fabricated from the liquid phase as long as pure enough solvents are available. The detectors have responded at reach minimum wavenumbers. Optimization of the Sb doping concentration should further decrease the photoionization energy of these detectors. Ge BIB detectors have been fabricated that respond to 60 cm(exp -1) with low responsivity. Through reduction of the minority residual impurities, detector performance has reached responsivities of 1 A/W. These detectors have exhibited quantum efficiency and NEP values that rival conventional photoconductors and are expected to provide a much more sensitive tool for new scientific discoveries in a number of fields, including solid state studies, astronomy, and cosmology.

Olsen, C. S.↗
NASA NTRS1976

Moessbauer effect measurement in single crystal iron subjected to cyclic stress

Backscattered Moessbauer spectra were recorded at different fatigue levels in cyclically fatigued high-purity single-crystal iron specimens in the form of rectangular strips with appropriate concentrators in the midplane. The Moessbauer spectra were submitted to a least-squares analysis to determine the isomer shift, quadrupole shift, hyperfine field, and peak spectral widths in each spectrum. It is shown that the quadrupole shift and the isomer shift changed little with fatigue, whereas the effective internal field and the associate line widths exhibit significant variation as a function of fatigue level. It is concluded that the impurity concentration builds up slowly with increasing fatigue level in the region of stress concentration. Since there is a direct correlation between crack initiation and defect concentration level, it is expected that Moessbauer measurements in the test specimen can provide a means of monitoring the impurity buildup presumed to be the eventual cause of fatigue crack initiation and failure.

Singh, J. J.↗
NASA NTRS2001

Investigating the Effect of Impurities on Macromolecule Crystal Growth in Microgravity

Chicken egg-white lysozyme (CEWL) crystals were grown in microgravity and on the ground in the presence of various amounts of a naturally occurring lysozyme dimer impurity. No significant favorable differences in impurity incorporation between microgravity and ground crystal samples were observed. At low impurity concentration the microgravity crystals preferentially incorporated the dimer. The presence of the dimer in the crystallization solutions in microgravity reduced crystal size, increased mosaicity and reduced the signal to noise ratio of the X-ray data. Microgravity samples proved more sensitive to impurity. Accurate indexing of the reflections proved critical to the X-ray analysis. The largest crystals with the best X-ray diffraction properties were grown from pure solution in microgravity.

Snell, Edward H.↗
NASA NTRS1976

Silicon solar cells from transition metal doped Czochralski and web crystals

The influence of metallic impurities on solar cell characteristics has been examined to establish the cost sensitive purity versus performance trade-offs. Solar cells were fabricated on 2 to 4 ohm-cm p-type substrates obtained by Czochralski and dendritic web growth processes. Controlled amounts of metallic impurities were introduced into the melt during growth and included Fe, Cr, Mn, Ni, Cu, Ti, V, Zr, Mg, Zn, and Al. Impurity concentrations in the crystals were determined using emission and mass spectrographic techniques and in some cases by neutron activation analysis. The solar cells were characterized by means of a computer program to curve-fit measured voltage-current data. The principal effect of the added impurities is a degradation of lifetime and diffusion length.

Davis, J. R.↗
NASA NTRS1985

Potential productivity benefits of float-zone versus Czochralski crystal growth

Efficient mass production of single-crystal silicon is necessary for the efficient silicon solar arrays needed in the coming decade. However, it is anticipated that there will be difficulty growing such volumes of crystals using conventional Czochralski (Cz) methods. While the productivity of single crystals might increase with a crystal diameter increase, there are two obstacles to the mass production of large diameter Czochralski crystals, the long production cycle due to slow growth rate and the high heat requirements of the furnaces. Also counterproductive would be the large resistivity gradient along the growth direction of the crystals due to impurity concentration. Comparison between Float zone (FZ) and Cz crystal growth on the basis of a crystal 150 mm in diameter is on an order of two to four times in favor of the FZ method. This advantage results from high growth rates and steady-state growth while maintaining a dislocation-free condition and impurity segregation.

Abe, T.↗
NASA NTRS1984

Study of factors determining the radiation sensitivity of quartz crystal oscillators (A0189)

The correlation between defect cluster concentrations observed for different grades of quartz examined by transmission electron microscopy (TEM) and the electrical stability of quartz resonators exposed to complex radiation in an orbital LDEF was determined. It is demonstrated that the technique TEM provides a powerful method for studying the effect of radiation on crystalline quartz. Two factors suggest that the observed clusters may be responsible for the radiation-induced frequency drift and acoustic absorption effects associated with irradiated quartz resonators: (1) the clusters are expected to be very effective in modifying the piezoelectric properties of quartz because of the large strain fields associated with them; (2) both phenomena appear to be sensitive to the impurity concentration. It is suggested that TEM can be used to classify grades of quartz according to their suitability for use in radiation-hard resonators. This technique may identify the impurities that are responsible and thereby effect an improvement in the stability of quartz oscillators.

Venables, J. D.↗
NASA NTRS1978

High-purity silicon for solar cell applications

The article discusses the production of solar cells from high-purity silicon. The process consists of reducing the level of impurities in the raw materials, preventing material contamination before and after entering the furnace, and performing orders-of-magnitude reduction of metal impurity concentrations. The high-purity raw materials are considered with reference to carbon reductants, silica, and graphite electrodes. Attention is also given to smelting experiments used to demonstrate, in an experimental-scale furnace, the production of high-purity SoG-Si. It is found that high-purity silicon may be produced from high-purity quartz and chemically purified charcoal in a 50-kVA arc furnace. The major contamination source is shown to be impurities from the carbon reducing materials.

Dosaj, V. D.↗