SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The thickness noise theory is discussed. Two full-scale rotors were tested in a wind tunnel with several tips involving changes in chord, thickness, and sweep. Impulsive noise data reduction procedures used are described. The calculated and measured impulsive noise peak pressures as a function of advancing tip Mach number are compared, showing good correlation for all rotors considered.
The results of a recent wind tunnel test program to evaluate the effectiveness of the Tip Air Mass Injection (TAMI) system in modifying the blade tip vortex occurring during helicopter flight is described with attention to the effect of this modification on the impulsive noise. The measurement program is explained, and the correlation between experimental and predicted results is discussed. Topics considered include the effect of descent rate on noise pressure time histories, the effect of air mass injection on noise, and the analysis based on a dB(A) weighted approach. Impulsive noise generated by the interaction of a helicopter rotor blade and the concentrated tip vortex during forward flight descent is a primary contributor to acoustic annoyance as it draws early attention to the presence of the helicopter.
In-plane impulsive noise radiating from a hovering model rotor was measured in an anechoic environment. The hover acoustic signature was compared with existing theoretical prediction models with previous forward flight experiments using the same model rotor. These hover tests showed good experimental consistency with forward flight measurements, both in pressure level, and waveform character, over the range of Mach numbers tested (0.8 to 1.0). Generally poor correlation, however, was confirmed with current linear theory prediction efforts. Failure to predict both the peak pressure levels and the shape was reported, especially with increasing tip Mach number.
Guinea pig cochlear hair cell damage after exposure to impulse noise
One detonation test was monitored for impulse noise at Thunder Range on November 6, 2020. The TNT equivalency for this shot was 100 lbs. Ground zero for this test was located at an open area of Range 7. The Armag, where MOW were remotely located, was just south of the east end of the TR shock tube The purpose of this sampling event was to characterize the noise attenuation provided by the Armag which will be used as the primary firing location in a future test series. To determine attenuation provided by the Armag, one sound level monitor was placed inside and a second monitor was placed outside the hardened structure at the same distance from ground zero. The Armag was located 1300 feet from ground zero. Essential personnel performing these tests were remotely located inside the Armag and wore hearing protection with a minimum NRR of 23. Members of the Workforce (MOW) who are exposed to noise levels above 140 dBC, regardless of hearing protection worn, are required to be enrolled into the SNL Hearing Conservation Program which includes audiometric testing, online training (HCP100) and wearing hearing protection.
FM demodulation threshold extension by correlation detection implemented in impulse noise cancellation system
Error probabilities of matched filter receiver operating in additive combination of impulsive and Gaussian noise
A 1/17-scale research model of the AH-1 series helicopter main rotor was tested. Model-rotor acoustic and simultaneous blade pressure data were recorded at high speeds where full-scale helicopter high-speed impulsive noise levels are known to be dominant. Model-rotor measurements of the peak acoustic pressure levels, waveform shapes, and directively patterns are directly compared with full-scale investigations, using an equivalent in-flight technique. Model acoustic data are shown to scale remarkably well in shape and in amplitude with full-scale results. Model rotor-blade pressures are presented for rotor operating conditions both with and without shock-like discontinuities in the radiated acoustic waveform. Acoustically, both model and full-scale measurements support current evidence that above certain high subsonic advancing-tip Mach numbers, local shock waves that exist on the rotor blades ""delocalize'' and radiate to the acoustic far-field.
A computer program is presented for calculating the source location of implusive noise in helicopters. The program (INSL) is written in FORTRAN for the CDC 7600 computer. Inputs are the rotor operating conditions and the time intervals (T) between rotor 1/rev index and impulsive noises as measured by different microphones. The outputs are the possible noise source locations in terms of rotor radial and azimuthal coordinates. Typical computer time for a run of six microphone measurements is 1.5 sec, and the cost is about 12 cents for the CDC 7600.
A controlled wind tunnel test program was conducted on a model 2.14 m (7 ft) diameter teetering rotor to determine the effectiveness of blade tips such as the Ogee tip and the TAMI (Tip Air Mass Injection) tip in reducing the impulsive noise due to blade-vortex interaction in descent flight. In addition, a full rectangular tip which has the same span as the Ogee tip and an effective rectangular tip which has the same lifting area as the Ogee tip were also considered. The tests were conducted at two advance ratios (0.125 and 0.14) with various descent rates ranging from steady level flight to about 6 m/sec (20 ft/sec). A comparison of the performance of different rotors showed that for the same tip Mach number and thrust, the Ogee tip rotor absorbed more power than the full rectangular tip rotor, while the TAMI tip rotor absorbed more power than the effective tip rotor.
Results are presented of a model rotor acoustics test performed to examine the benefit of higher harmonic control (HHC) of blade pitch to reduce blade-vortex interaction (BVI) impulsive noise. A dynamically scaled, four-bladed, rigid rotor model, a 40-percent replica of the B0-105 main rotor, was tested in the German Dutch Wind Tunnel. Noise characteristics and noise directivity patterns as well as vibratory loads were measured and used to demonstrate the changes when different HHC schedules were applied. Dramatic changes of the acoustic signatures and the noise radiation directivity with the HHC phase variations are found. Compared to the baseline conditions (without HHC), significant mid-frequency noise reductions of locally 6 dB are obtained for low-speed descent conditions where GVI is most intense. For other rotor operating conditions with less intense BVI there is less or no benefit from the use of HHC. LF noise and vibratory loads, especially at optimum noise reduction control settings, are found to increase.
A new method is developed for modeling helicopter high-speed impulsive (HSI) noise. The aerodynamics and acoustics near the rotor blade tip are computed by solving the Euler equations on an unstructured grid. A stationary Kirchhoff surface integral is then used to propagate these acoustic signals to the far field. The near-field Euler solver uses a solution-adaptive grid scheme to improve the resolution of the acoustic signal. Grid points are locally added and/or deleted from the mesh at each adaptive step. An important part of this procedure is the choice of an appropriate error indicator. The error indicator is computed from the flow field solution and determines the regions for mesh coarsening and refinement. Computed results for HSI noise compare favorably with experimental data for three different hovering rotor cases.
The inability to systematically predict community response to exposure to sonic booms (and other high energy impulsive sounds) is a major impediment to credible analyses of the environmental effects of supersonic flight operations. Efforts to assess community response to high energy impulsive sounds are limited in at least two important ways. First, a paucity of appropriate empirical data makes it difficult to infer a dosage-response relationship by means similar to those used in the case of general transportation noise. Second, it is unclear how well the 'equal energy hypothesis' (the notion that duration, number, and level of individual events are directly interchangeable determinants of annoyance) applies to some forms of impulsive noise exposure. Some of the issues currently under consideration by a CHABA working group addressing these problems are discussed. These include means for applying information gained in controlled exposure studies about different rates of growth of annoyance with impulsive and non-impulsive sound exposure levels, and strategies for developing a dosage-response relationship in a data-poor area.
The thresholds of detection of low frequency, impulsive wind turbine sounds in the presence of background noise were examined. Seven wind turbine sounds, six of which were synthesized, were used in conjunction with three background noise conditions; quiet, 35, and 45 dB(A). The results indicate that thresholds of detection are predictable based on assumed characteristics of the auditory system. The synthesized wind turbine sounds were found to adequately represent a real recording.
Two impulsive sound sources, one using multiple acoustic drivers and the other using a spark discharge were developed to study the acoustic reflection characteristics of hard-walled wind tunnels, and the results of laboratory tests are presented. The analysis indicates that though the intensity of the pulse generated by the spark source was higher than that obtained from the acoustic source, the number of averages needed for a particular test may require an unacceptibly long tunnel-run time due to the low spark generation repeat rate because of capacitor charging time. The additional hardware problems associated with the longevity of electrodes and electrode holders in sustaining the impact of repetitive spark discharges, show the multidriver acoustic source to be more suitable for this application.
An acoustic source localization scheme applicable to noncompact moving sources is developed and applied to the blade-vortex interaction (BVI) noise data of a 40-percent scale BO-105 model rotor. A generalized rotor wake code is employed to predict possible VBI locations on the rotor disk and is found quite useful in interpreting the acoustic localization results. The highly varying directivity patterns of different BVI impulses generated at the same test condition are explained by both the localization results and predicted tip vortex trajectories. The effects of rotor tip-path-plane angle and advance ratio on the BVI source positions is studied. Decreasing tip-path-plane angle (at constant advance ratio) moves the general interaction region upwind on the rotor disk, significantly changing the interaction geometry. Increasing advance ratio (at constant tip-path-plane angle) shifts the general source region downwind on the rotor disk with the increased convection of the vortices until about 60 deg azimuth, where the BVI sources appear to become acoustically less effective. The region of strongest BVI sources lies between 60 and 70 deg azimuth and 80 and 90 percent radius for the moderate range of advance ratios studied.
On October 1, 2022, sound level measurements were taken at various locations throughout Kirtland Air Force Base (KAFB) and Southeastern Albuquerque. The purpose was to support sound propagation modeling predictions and sound regulations for public exposure during the detonation of an approximately 300-pound energetic experiment. Ground Zero was located on Range 7 of Sandia Thunder Range (06647). A total of 8 measurement locations were identified (e.g., 5 on KAFB and 3 in the Southeastern Albuquerque neighborhoods).
An FM click noise suppressor was evaluated by means of several experimental tests conducted to verify previous test results. The range and worst case type of operation for the suppressor were also determined. A brief theoretical justification for the existence of FM click noise near threshold conditions is presented. It is concluded that the circuit does perform click suppression, but over a limited range. Suggestions for improvement of the circuit are given.