SEARCH · Engineering Papers

Results for “high solid loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Effect of using a nitrogen atmosphere on enzyme hydrolysis at high corn stover loadings in an agitated reactor

A comprehensive review of the literature shows that enzyme hydrolysis efficiency decreases with increased solids loadings at constant enzyme:cellulose ratios for pretreated lignocellulosic substrates. In seeking a mechanistic explanation for this phenomenon, we found that a nitrogen atmosphere enhances enzyme hydrolysis and minimizes the decrease in glucose yields as solids loadings are increased in an agitated bioreactor. Further, for liquid hot water pretreated corn stover, at solids loadings of both 100 and 200 g/L and hydrolyzed for 72 hr in a 1 L bioreactor at pH 5.0 with 3.6 mg protein per g biomass, glucose yields were 55% in a nitrogen atmosphere versus 45% in air with agitation and about 34% without agitation. While mixing promotes biomass/enzyme contact and disperses sugars released during hydrolysis that would otherwise cause product inhibition, nitrogen gas displaces air, avoiding deactivation of cellulases by oxygen. The nitrogen effect points to a facile approach of enhancing hydrolysis at high solids loadings.

09 BIOMASS FUELS↗

DOE OSTI2020

Phase distribution in Fischer-Tropsch mimicked slurry bubble column via computed tomography

This study aims to investigate the phases distribution and hydrodynamics in an air-Therminol LT-glass beads slurry bubble column reactor in bubbly and churn-turbulent flow regimes by implementing a gamma-ray computed tomography. It is found that gas holdup increases with increasing superficial gas velocity and operating pressure while increasing solids loading has an opposite effect on gas holdup measurements. It is noticed that the pressure effect is more significant at high solids loading and the solids loading is relatively more substantial at lower pressure. Solids loading has the most significant a stronger effect on the solids holdup profile than on the gas holdup profile. Current results were compared with the Sedimentation-Dispersion Model (SDM) predictions. Overall, the findings of this study advance the knowledge of the true behavior of phases distribution in FT mimicked slurry bubble columns which are pertinent in designing such reactors.

42 ENGINEERING↗

DOE OSTI2023

Techno-economic assessment and life cycle assessment of three potential pathways for biomass liquefaction

Biomass liquefaction can enhance corn-stover slurry transportation by reducing yield stress and overall viscosity, easing biomass handling, especially for slurries at high solids loading (≥30 % (w/v). Implementing a liquefaction process at the front-end of the biorefinery could reduce downtime caused by equipment fouling. Furthermore, liquefaction reduces process complexity by transforming high fiber mass into a pumpable slurry. Three scenarios for liquefaction of corn stover pellets: enzyme process, enzyme mimetic process, and a combined process of enzyme and enzyme mimetic were assessed. The ideal process will have the best performance-to-cost ratio, with minimal impact on the environment. Techno-economic and life-cycle analyses were used to understand the economic and environmental effects of the three liquefaction scenarios and to determine if one or more can achieve cost parity. Here, results show that the enzyme process had the best performance in terms of cost and emissions (gCO 2 -equivalent/kg slurry)compared to the other scenarios.

09 BIOMASS FUELS↗

DOE OSTI2024

Data for Process Strategies for Recovery of Sugars, Lipids, and Lignin from Oilcane Bagasse Using Natural Deep Eutectic Solvents (NADES)

Sugarcane is being enhanced as a bioenergy crop by engineering it to accumulate and store lipids along with polymeric sugars in vegetative tissues. However, there is no existing process that allows for processing this new crop to recover both lipid and cellulosic sugars from the oilcane bagasse. Therefore, a comprehensive investigation of two pretreatment methods—natural deep eutectic solvents (NADES) and chemical-free hydrothermal pretreatment (HT) was conducted to judge their suitability for recovering fermentable sugars, lipids, and lignin from bagasse. Two NADES, i.e., choline chloride: lactic acid (ChCl:LA) and betaine: lactic acid (BT:LA) were prepared using a 1:2 M ratio and were evaluated for pretreatment of oilcane bagasse at 10, 20, and 50 % (w/w) solids, followed by enzymatic hydrolysis at 10 % (w/w) solids. Notably, ChCl:LA NADES treatment at 10 % (w/w) solids at 140 °C for 2 h, solubilized 78.8 % of lignin and 80.4 % of hemicellulose and allowed 82.7 % enzymatic conversion of glucans to glucose. In contrast, HT pretreatment removed approximately 87.6 % of the hemicellulose and provided an enzymatic glucose yield of 69.7 %. Furthermore, ChCl:LA operated at 50 % solids loading the enriched lipids 2.6-fold (9.2 wt%) in recovered solids compared to HT (6.4 %) and BT:LA (5.1 %) pretreatment processes. NMR-HSQC and GPC analysis showed that ChCl:LA also cleaved the most lignin β–O–4 linkages and demonstrated lower molecular weight compared to HT. This study demonstrates that NADES pretreatment is an effective green processing method for recovering lipids, sugars, and lignin from bioenergy crops at high solid loading (50 % w/w) within the context of an integrated biorefinery.

Conversion↗

DOE OSTI2024

Process strategies for recovery of sugars, lipids, and lignin from oilcane bagasse using natural deep eutectic solvents (NADES)

Sugarcane is being enhanced as a bioenergy crop by engineering it to accumulate and store lipids along with polymeric sugars in vegetative tissues. However, there is no existing process that allows for processing this new crop to recover both lipid and cellulosic sugars from the oilcane bagasse. Therefore, a comprehensive investi- gation of two pretreatment methods—natural deep eutectic solvents (NADES) and chemical-free hydrothermal pretreatment (HT) was conducted to judge their suitability for recovering fermentable sugars, lipids, and lignin from bagasse. Two NADES, i.e., choline chloride: lactic acid (ChCl:LA) and betaine: lactic acid (BT:LA) were prepared using a 1:2 M ratio and were evaluated for pretreatment of oilcane bagasse at 10, 20, and 50 % (w/w) solids, followed by enzymatic hydrolysis at 10 % (w/w) solids. Notably, ChCl:LA NADES treatment at 10 % (w/ w) solids at 140 °C for 2 h, solubilized 78.8 % of lignin and 80.4 % of hemicellulose and allowed 82.7 % enzymatic conversion of glucans to glucose. In contrast, HT pretreatment removed approximately 87.6 % of the hemicellulose and provided an enzymatic glucose yield of 69.7 %. Furthermore, ChCl:LA operated at 50 % solids loading the enriched lipids 2.6-fold (9.2 wt%) in recovered solids compared to HT (6.4 %) and BT:LA (5.1 %) pretreatment processes. NMR-HSQC and GPC analysis showed that ChCl:LA also cleaved the most lignin β–O–4 linkages and demonstrated lower molecular weight compared to HT. As a result, this study demonstrates that NADES pretreatment is an effective green processing method for recovering lipids, sugars, and lignin from bioenergy crops at high solid loading (50 % w/w) within the context of an integrated biorefinery.

09 BIOMASS FUELS↗

DOE OSTI2021

All solid thick oxide cathodes based on low temperature sintering for high energy solid batteries

Solid-state batteries (SSBs) could significantly improve the safety and energy density over conventional liquid cells. One key enabling technology is the use of solid electrolytes. NASICON-type Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 (LATP) is a very attractive solid-state electrolyte for the cathode side due to its high oxidation potential and high ionic conductivity. The usage, however, is limited by its large interfacial resistance against most of the cathode materials as well as the thermodynamic instability during high temperature sintering needed to achieve high mass density. Here we construct thin, percolative, and mixed conductive interphases through in situ low-melting-point liquid sintering. These mixed conductive interphases drastically improve the kinetics, leading to high-loading solid LATP/LiCoO 2 cathodes achieving capacity loading of up to ~6 mA h cm –2 . The technique is also applicable to Ni-rich cathode materials, achieving up to ~10 mAh cm –2 , which can lead to more than 400 W h kg –1 cells in SSBs. Furthermore, our composite cathodes show a ten-times and three-times area capacity improvement over the state-of-the-art cathodes using oxide and sulfide SSEs, respectively.

25 ENERGY STORAGE↗

DOE OSTI2024

Natural deep eutectic solvents (NADES) assisted deconstruction of oilcane bagasse for high lipid and sugar recovery

In a novel approach, metabolically engineered sugarcane “Oilcane” has been investigated for fractionation of lipid and cellulose-rich pulp, using certain Natural deep eutectic solvents (NADES). The exploration of eco- friendly solvents are at the forefront of harnessing the biofuel potential of modern bioenergy crops. For this, six combinations of NADES were prepared using choline chloride (ChCl) as HBA and lactic acid (LA), oxalic acid (OA) and glycerol (Gly) as HBD and were further explored for pretreatment of oilcane bagasse in a molar ratio of 1:1 and 1:2. The impact of NADES ratio, biomass loading (10–50%), residence time (1–2 h), and temperature (90–140 °C) were evaluated for delignification, lipid content, sugar release after enzymatic hydrolysis. The finding demonstrated that under the optimal condition of ChCl: LA (1:2 molar ratio), 140 °C with 2 h retention time, the lipid content in the pre-treated substrate was increased to 2.5-fold (~8% w/w) and > 80% glucose yield was achieved after 72 h of hydrolysis of pre-treated bagasse. High solid loading (~50%) during pretreatment resulted in a similar glucose yield. Furthermore, recycling studies demonstrated that nearly 95 to 98% NADES could be recycled after each pretreatment for up to five consecutive cycles without any significant loss in chemical structure as confirmed by 1 H NMR and FT IR. FT IR and XRD analyses of native and pre-treated biomass were performed to visualize the morphological changes during NADES pretreatment and their impact on sugar yield. The findings of the study may be used to establish NADES-based biorefinery for the valorization of lipids, and carbohydrates for fuels and chemicals production.

09 BIOMASS FUELS↗

DOE OSTI2024

Data for Natural Deep Eutectic Solvents (NADES) Assisted Deconstruction of Oilcane Bagasse for High Lipid and Sugar Recovery

In a novel approach, metabolically engineered sugarcane “Oilcane” has been investigated for fractionation of lipid and cellulose-rich pulp, using certain Natural deep eutectic solvents (NADES). The exploration of eco-friendly solvents are at the forefront of harnessing the biofuel potential of modern bioenergy crops. For this, six combinations of NADES were prepared using choline chloride (ChCl) as HBA and lactic acid (LA), oxalic acid (OA) and glycerol (Gly) as HBD and were further explored for pretreatment of oilcane bagasse in a molar ratio of 1:1 and 1:2. The impact of NADES ratio, biomass loading (10–50%), residence time (1–2 h), and temperature (90–140 °C) were evaluated for delignification, lipid content, sugar release after enzymatic hydrolysis. The finding demonstrated that under the optimal condition of ChCl: LA (1:2 molar ratio), 140 °C with 2 h retention time, the lipid content in the pre-treated substrate was increased to 2.5-fold (∼8% w/w) and > 80% glucose yield was achieved after 72 h of hydrolysis of pre-treated bagasse. High solid loading (∼50%) during pretreatment resulted in a similar glucose yield. Furthermore, recycling studies demonstrated that nearly 95 to 98% NADES could be recycled after each pretreatment for up to five consecutive cycles without any significant loss in chemical structure as confirmed by 1H NMR and FT IR. FT IR and XRD analyses of native and pre-treated biomass were performed to visualize the morphological changes during NADES pretreatment and their impact on sugar yield. The findings of the study may be used to establish NADES-based biorefinery for the valorization of lipids, and carbohydrates for fuels and chemicals production.

Conversion↗

DOE OSTI2021

Coculture with hemicellulose-fermenting microbes reverses inhibition of corn fiber solubilization by Clostridium thermocellum at elevated solids loadings

Abstract Background The cellulolytic thermophile Clostridium thermocellum is an important biocatalyst due to its ability to solubilize lignocellulosic feedstocks without the need for pretreatment or exogenous enzyme addition. At low concentrations of substrate, C. thermocellum can solubilize corn fiber > 95% in 5 days, but solubilization declines markedly at substrate concentrations higher than 20 g/L. This differs for model cellulose like Avicel, on which the maximum solubilization rate increases in proportion to substrate concentration. The goal of this study was to examine fermentation at increasing corn fiber concentrations and investigate possible reasons for declining performance. Results The rate of growth of C. thermocellum on corn fiber, inferred from CipA scaffoldin levels measured by LC–MS/MS, showed very little increase with increasing solids loading. To test for inhibition, we evaluated the effects of spent broth on growth and cellulase activity. The liquids remaining after corn fiber fermentation were found to be strongly inhibitory to growth on cellobiose, a substrate that does not require cellulose hydrolysis. Additionally, the hydrolytic activity of C. thermocellum cellulase was also reduced to less-than half by adding spent broth. Noting that > 15 g/L hemicellulose oligosaccharides accumulated in the spent broth of a 40 g/L corn fiber fermentation, we tested the effect of various model carbohydrates on growth on cellobiose and Avicel. Some compounds like xylooligosaccharides caused a decline in cellulolytic activity and a reduction in the maximum solubilization rate on Avicel. However, there were no relevant model compounds that could replicate the strong inhibition by spent broth on C. thermocellum growth on cellobiose. Cocultures of C. thermocellum with hemicellulose-consuming partners— Herbinix spp. strain LL1355 and Thermoanaerobacterium thermosaccharolyticum —exhibited lower levels of unfermented hemicellulose hydrolysis products, a doubling of the maximum solubilization rate, and final solubilization increased from 67 to 93%. Conclusions This study documents inhibition of C. thermocellum with increasing corn fiber concentration and demonstrates inhibition of cellulase activity by xylooligosaccharides, but further work is needed to understand why growth on cellobiose was inhibited by corn fiber fermentation broth. Our results support the importance of hemicellulose-utilizing coculture partners to augment C. thermocellum in the fermentation of lignocellulosic feedstocks at high solids loading.

09 BIOMASS FUELS↗

DOE OSTI2025

Evaluating the industrial potential of emerging biomass pretreatment technologies in bioethanol production and lipid recovery from transgenic sugarcane

The selection of pretreatment methods is critical to achieving high product yields during bioconversion of lignocellulosic biomass. Hydrothermal, soaking-in-aqueous ammonia, and ionic liquid pretreatment methods are viable candidates for minimizing sugar decomposition, permitting the effective hydrolysis of structural carbohydrates, and producing a fermentable substrate suitable for achieving industrial ethanol titers and yields. In this study, the effect of these three pretreatment methods on non-modified sugarcane cultivar CP88-1762 and two transgenic lipid-accumulating sugarcane lines, oilcane 1565 and oilcane 1566, were investigated and compared in terms of lipid recovery, sugar yield, and ethanol yields within the lignocellulosic biomass conversion pipeline. Fed-batch enzymatic hydrolysis at high solid loading yielded hydrolysates capable of supporting industrial bioethanol titers across all conditions. The highest sugar yields were obtained on ammonia-pretreated biomass hydrolysate (253.73 g L −1 ), followed by hydrothermally pretreated hydrolysate (213.10 g L −1 ) and ionic liquid-pretreated hydrolysate (154.20 g L −1 ). Commercially viable ethanol titers of 100.62 g L −1 , 64.47 g L −1 , and 52.95 g L −1 were achieved from ammonia, hydrothermal, and ionic liquid pretreated hydrolysate with the corresponding ethanol productivities of 2.08 g L −1 h −1 , 0.53 g L −1 h −1 , and 0.36 g L −1 h −1 . The lower acetic acid concentration in ammonia-pretreated hydrolysate may have enhanced its fermentability relative to the hydrothermal pretreatment condition, as indicated by the differences in ethanol titer and productivity. Lower sugar yields and ethanol productivities under the ionic liquid conditions likely resulted from the inhibitory effect of cholinium lysinate. Oilcane 1565 and oilcane 1566 bagasse accumulated over 16- and 3 times higher lipids than the non-modified sugarcane CP88-1762. The total fatty acid content in the oilcane samples was reduced in ammonia and ionic liquid-pretreated bagasse relative to the hydrothermal pretreatment condition. While all pretreatment techniques tested are industrially viable, the observed differences in titer, productivity, and lipid content indicate that careful selection and validation of upstream processing methods can contribute to improved economic and environmental outcomes.

09 BIOMASS FUELS↗

DOE OSTI2023

Time-temperature-stress superposition of PBX 9502 compressive creep data for lifetime predictions

The plastic-bonded explosive (PBX) 9502 is a viscoelastic, high-solids loaded polymer bound composite comprised of 95 weight% (wt%) TATB explosive crystals and 5 wt% FK-800 polymer binder. The uniaxial quasi-static mechanical properties have been studied and characterized extensively over 25+ years, including creep. Creep is the strain evolution over time as a result of an asymmetric load typically at temperatures above ambient. Creep measurements to failure can take excessively long periods of time depending on various factors including applied stress, temperature, and loading rate that render a single test to failure impossible. Using the principles of time-temperature-stress superposition (TTSSP), short-term creep tests at various applied stresses and temperatures can be used for long-term creep predictions. The TTSSP model shifts short-term test data using two factors, one for temperature and stress, creating a master curve at a reference test condition. The master curve can be shifted to predict the creep response at any desired test condition. PBX 9502 compression specimens were tested at three temperatures and various applied stresses. This work discusses the TTSSP analysis of PBX 9502 compressive creep data to create a single comprehensive master curve.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Water-soluble saponins accumulate in drought-stressed switchgrass and may inhibit yeast growth during bioethanol production

Abstract Background Developing economically viable pathways to produce renewable energy has become an important research theme in recent years. Lignocellulosic biomass is a promising feedstock that can be converted into second-generation biofuels and bioproducts. Global warming has adversely affected climate change causing many environmental changes that have impacted earth surface temperature and rainfall patterns. Recent research has shown that environmental growth conditions altered the composition of drought-stressed switchgrass and directly influenced the extent of biomass conversion to fuels by completely inhibiting yeast growth during fermentation. Our goal in this project was to find a way to overcome the microbial inhibition and characterize specific compounds that led to this inhibition. Additionally, we also determined if these microbial inhibitors were plant-generated compounds, by-products of the pretreatment process, or a combination of both. Results Switchgrass harvested in drought (2012) and non-drought (2010) years were pretreated using Ammonia Fiber Expansion (AFEX). Untreated and AFEX processed samples were then extracted using solvents (i.e., water, ethanol, and ethyl acetate) to selectively remove potential inhibitory compounds and determine whether pretreatment affects the inhibition. High solids loading enzymatic hydrolysis was performed on all samples, followed by fermentation using engineered Saccharomyces cerevisiae . Fermentation rate, cell growth, sugar consumption, and ethanol production were used to evaluate fermentation performance. We found that water extraction of drought-year switchgrass before AFEX pretreatment reduced the inhibition of yeast fermentation. The extracts were analyzed using liquid chromatography–mass spectrometry (LC–MS) to detect compounds enriched in the extracted fractions. Saponins, a class of plant-generated triterpene or steroidal glycosides, were found to be significantly more abundant in the water extracts from drought-year (inhibitory) switchgrass. The inhibitory nature of the saponins in switchgrass hydrolysate was validated by spiking commercially available saponin standard (protodioscin) in non-inhibitory switchgrass hydrolysate harvested in normal year. Conclusions Adding a water extraction step prior to AFEX-pretreatment of drought-stressed switchgrass effectively overcame inhibition of yeast growth during bioethanol production. Saponins appear to be generated by the plant as a response to drought as they were significantly more abundant in the drought-stressed switchgrass water extracts and may contribute toward yeast inhibition in drought-stressed switchgrass hydrolysates.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2025

Data for "Evaluating the industrial potential of emerging biomass pretreatment technologies in bioethanol production and lipid recovery from transgenic sugarcane"

The selection of pretreatment methods is critical to achieving high product yields during bioconversion of lignocellulosic biomass. Hydrothermal, soaking-in-aqueous ammonia, and ionic liquid pretreatment methods are viable candidates for minimizing sugar decomposition, permitting the effective hydrolysis of structural carbohydrates, and producing a fermentable substrate suitable for achieving industrial ethanol titers and yields. In this study, the effect of these three pretreatment methods on non-modified sugarcane cultivar CP88-1762 and two transgenic lipid-accumulating sugarcane lines, oilcane 1565 and oilcane 1566, were investigated and compared in terms of lipid recovery, sugar yield, and ethanol yields within the lignocellulosic biomass conversion pipeline. Fed-batch enzymatic hydrolysis at high solid loading yielded hydrolysates capable of supporting industrial bioethanol titers across all conditions. The highest sugar yields were obtained on ammonia-pretreated biomass hydrolysate (253.73 g L−1), followed by hydrothermally pretreated hydrolysate (213.10 g L−1) and ionic liquid-pretreated hydrolysate (154.20 g L−1). Commercially viable ethanol titers of 100.62 g L−1, 64.47 g L−1, and 52.95 g L−1 were achieved from ammonia, hydrothermal, and ionic liquid pretreated hydrolysate with the corresponding ethanol productivities of 2.08 g L−1 h−1, 0.53 g L−1 h−1, and 0.36 g L−1 h−1. The lower acetic acid concentration in ammonia-pretreated hydrolysate may have enhanced its fermentability relative to the hydrothermal pretreatment condition, as indicated by the differences in ethanol titer and productivity. Lower sugar yields and ethanol productivities under the ionic liquid conditions likely resulted from the inhibitory effect of cholinium lysinate. Oilcane 1565 and oilcane 1566 bagasse accumulated over 16- and 3 times higher lipids than the non-modified sugarcane CP88-1762. The total fatty acid content in the oilcane samples was reduced in ammonia and ionic liquid-pretreated bagasse relative to the hydrothermal pretreatment condition. While all pretreatment techniques tested are industrially viable, the observed differences in titer, productivity, and lipid content indicate that careful selection and validation of upstream processing methods can contribute to improved economic and environmental outcomes.

biomass analytics↗

DOE OSTI2023

Liquefaction of different corn stover fractions assisted by enzyme-biomass deconstruction

Recalcitrant properties of different sources of lignocellulosic biomass represent challenges in materials processing within a biorefinery, as well as enzyme efficient deconstruction to fermentable sugars. Limitations include lignin derived enzyme inhibitors, enzyme inhibition by hydrolysis products, and resistance to mixing due to rheological properties of lignocellulosic particulates at high solids loadings. Consequently, we examined conditions that might be used to achieve liquid slurries (i.e., liquefaction) at solids loadings of 300 g/L before the material enters the biorefinery through a pretreatment step. This work explores enzyme-assisted liquefaction in a fed-batch process using the commercial enzymes Celluclast 1.5L or Ctec-2 at 1FPU/g or 3 FPU/g of dry solids, basis. Corn stover pellets were fed into a 1 L stirred bioreactor containing enzyme solution over a 5-hour period until reaching 30% solids loading (dry wgt / vol basis). After 6, 24 and 96 hours from the start of the run, samples were taken and characterized with respect to their sugar composition, rheology, water absorption and enzyme activity. Slurries with dramatically reduced yield stresses were achieved for corn stover. Yield stresses of 178±7 Pa (3 FPU, Celluclast 1.5L) and 79±6 Pa (3FPU, Ctec-2) were measured for corn stover at 24 hours, compared to 6,000 Pa for samples without enzyme.Yield stress was 155± 29 Pa (3FPU, Ctec-2) and 257 ± 72 Pa (1 FPU, Celluclast 1.5L) for corn cobs at 24 hours.A profile based on 6, 24 and 96h of yield stress measurements and sugar conversion is presented. Enzyme activity is measured and the impact of liquefaction on an integrated processing in a biorefinery operation is discussed.

Gutierrez, Diana↗

DOE OSTI2023

Time-Temperature-Stress Superposition of PBX 9502 Compressive Creep Data for Lifetime Predictions

36 MATERIALS SCIENCE↗

DOE OSTI2024

UHT-CAMANCHE: Ultra-High Temperature Ceramic Additively Manufactured Compact Heat Exchangers

The conceptual basis for this project is the convergence of advanced ultra-high temperature ceramic materials and additive manufacturing technologies to produce compact ceramic heat exchangers with complex internal flow path geometries. Task areas were broadly divided into materials and manufacturing development, heat exchanger design, component testing, and techno-economic analysis. Technical challenges included the design and commissioning of new test facilities, improving feature resolution and deposition rate of ceramic additive manufacturing techniques, establishing process-structure-property relationships in additively manufactured ultra-high temperature ceramics, and assessing high temperature materials compatibility in CO 2 environments. The primary candidate material evaluated in this work is a composite comprising zirconium diboride (ZrB2) with 30 vol. % silicon carbide (SiC) which was selected based on its desirable combination of high temperature mechanical properties, high thermal and electrical conductivities, and oxidation resistance. High solids loaded ZrB2-SiC pastes suitable for extrusion-based additive manufacturing were developed for the first time as part of this work. Materials compatibility studies indicate this material oxidizes in CO 2 to form a protective borosilicate scale which transforms to pure silica above 1000°C. Parts made by additive manufacturing displayed enlarged grain sizes produced by pressureless sintering as compared to hot-press sintering. Increases in microstructural coarseness have outsized effect on oxidation performance up to 1400°C due to incomplete oxidation of coarse large diameter SiC particles resulting in lower amounts of silica that apparently inhibit protective scale formation. Additive manufacturing as a forming technique did not appear to significantly affect thermal conductivity, hardness, or elastic modulus, though flexural strength was reduced by half or more as compared to traditionally hot-pressed materials. This effect was attributed to the presence of strength-limiting flaws (ca. 40 microns in size) originating from extrudate inhomogeneities that could potentially be eliminated with further process improvements. Attempts to attain economies of scale for production of multi-kilowatt scale heat exchangers by ceramic additive manufacturing proved difficult. Lack of automation and a modest extrusion rate while retaining fine feature resolution made the overall process labor intensive and limited experimental throughput. A number of full-scale components were taken through post-process heat treatments including drying, binder burnout, and sintering; however, none survived without significant flaws or cracks. Therefore, no operational data from a newly installed heat exchanger test loop were able to be obtained during the performance period. Continued research and development is recommended to improve economic feasibility of ceramic additive manufacturing by standardizing the use of advanced sensors, artificial intelligence, and automation tools to reduce associated labor costs and accelerate production rates. The materials and manufacturing techniques demonstrated in this work are likely to find applications in defense and energy applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2022

Comparative Study on the Pretreatment of Aspen and Maple With 1-Ethyl-3-methylimidazolium Acetate and Cholinium Lysinate

The efficiency of the enzymatic digestibility of certain lignocellulosic biomass has been observed as a function of their structural and chemical changes which in turn depends on the ionic liquid (IL) used as the pretreatment solvent. This study demonstrated and compared the feasibility of the IL pretreatment process for two woody biomasses, namely maple and aspen, using two mechanistically distinct ILs, i.e., 1-ethyl-3-methylimidazolium acetate (C 2 mim][OAc]) and cholinium lysinate ([Ch][Lys]) as the solvent. The pretreatment was performed at three different temperatures of 100°C, 140°C, and 160°C at a high solid loading of 25 wt% to understand the impact of lignin content and crystallinity index on enzymatic digestibility. Saccharification of the biomass obtained after the IL pretreatment afforded 30–85% glucan conversions. For aspen, both [C 2 mim][OAc] and [Ch][Lys] exhibited the highest glucan conversion at 140°C. For maple, the highest glucan conversion was obtained at 140°C with [C 2 mim][OAc], whereas [Ch][Lys] had an optimum glucan conversion at 160°C. These pretreatments resulted in negligible delignification irrespective of the IL used. A significant loss of crystallinity was observed for all [C 2 mim][OAc]-pretreated biomasses, whereas the pretreatment with [Ch][Lys] resulted in an increase in the crystallinity index.

Choudhary, Hemant↗

DOE OSTI2026

Biohydrogen Generation from Un-Pretreated Spent Coffee Grounds with Clostridium Thermocellum

Coffee is among the world's most widely consumed beverages, generating 18 million wet tonnes of waste spent coffee grounds annually. Disposal of SCGs is complicated by their high moisture content, their recalcitrant chemical composition, and the presence of caffeine and other bioactive compounds. Dark fermentation is a promising technology for conversion of waste cellulosic biomass into renewable hydrogen, carbon dioxide, and volatile fatty acids. Typical SCGs have high moisture content, are pre-milled to fine particle sizes, and contain 8%-19% cellulose and up to 40% hemicellulose, making them an attractive feedstock for dark fermentation. In this study, we investigate biohydrogen production from unpretreated SCGs using Clostridium thermocellum strain KJC19-9, a cellulolytic bacterium engineered to co-utilize xylose, specifically examining the inhibitory effects of residual caffeine and high solids loadings on microbial growth and hydrogen production efficiency. While SCGs were initially resistant to both cell growth and biohydrogen production, a strategy to co-ferment with low concentrations of cellobiose dramatically enhanced process performance, reducing lag phase duration and enabling cellulosome production for efficient cellulose hydrolysis. This co-substrate approach generated up to 944 mL hydrogen per L reaction from 50 g/L of spent coffee grounds over 120 h (1.34 mol H2/mol carbohydrate), validating SCGs as a promising dark fermentation feedstock and underscoring the value of mixed substrate approaches in consolidated bioprocessing.

08 HYDROGEN↗