SEARCH · Engineering Papers

Results for “high average power”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS1993

Windshear radar calibration, 1992 flights: Transmitter power and receiver gain stability

During the 1992 NASA airborne Doppler windshear radar flights, radar calibrations were performed prior to each flight in order to determine transmitter power, receiver gain, and receiver noise power. The calibration results show that the average transmitter power in radar mode 6 was 186 watts, with a standard deviation of 7 watts. The average high power amplifier gain was 9.62 dB. At the wide IF bandwidth setting, the receiver gain was 123.1 dB, while at the narrow IF bandwidth setting, the gain was 121.8 dB. The receiver system noise as seen at the receiver input was -107.0 dBmw using the wide IF bandwidth and -107.9 dBmw using the narrow IF bandwidth. In radar mode 7, the receiver gain was the same as in mode 6. However, the receiver noise in mode 7 was about 2.5 dB less using the wide IF bandwidth and 2.0 dB less using the narrow IF bandwidth. The R/T unit flown in 1992 had also been flown the previous year when it produced comparable results. This technical memorandum was written as a follow-up to NASA TM-107589 (June 1992), which describes similar radar calibrations performed during the 1991 windshear radar flight experiments.

Mackenzie, Anne I.↗

NASA NTRS1979

Repetitively Q-switched Nd:BeL lasers

The thermal and mechanical characteristics which will ultimately limit the performance of Nd:BeL at high average power levels were investigated. The output beam characteristics (pulse width, peak power, beam dimensions and collimation) were determined at high repetition rates for both Nd:BeL and Nd:YAG. The output of Nd:BeL was shown to exceed that of Nd:YAG by a factor of 2.7 at low Q-switched repetition rates (1 Hz). This result follows from the smaller stimulated emission cross section of x-axis Nb:BeL compared to that of NdYAG by the same factor. At high repetition rates (10 Hz) the output of Nd:Bel falls to a level of three-fifths of its low repetition rate value while under similar tests the output of Nd:YAG remains essentially constant. A comparison of the measured values of the elasto-optic coefficients, the dn/dT values and the linear expansion coefficients for BeL and YAG failed to provide an explanation for the performance of BeL; however, thermal lensing was observed in Nd:BeL. Results imply that the output of a high repetition rate Q-switched Nd:BeL laser (high thermal loading) could be dramatically increased by utilization of a resonator design to compensate for the thermal lensing effects.

Degnan, J.↗

DOE OSTI2024

Proposed muon collider R&D at SNS

Generation of a muon beam at a Muon Collider requires relatively short, high-charge proton bunches. They are produced in a high-average-power proton driver by first accumulating a proton beam from a super-conducting linac, then bunching the beam and finally compressing and combining the bunches into a single high-intensity proton pulse. All of these beam formation stages involve handling of unprecedentedly high beam charges. Validation of these intricate beam manipulations requires better understanding of extreme space-charge effects and experimental demonstration. A facility perhaps most closely resembling the proton driver configuration and beam parameters is the Spallation Neutron Source (SNS) accelerator complex at Oak Ridge National Laboratory (ORNL). Considering the energy scaling of the space-charge parameters, many of the beam formation steps planned for the proton driver can be experimentally checked at the SNS at the relevant space-charge interaction levels. This paper discusses potential proton driver and other muon-collider-related R\&D at the SNS.

43 PARTICLE ACCELERATORS↗

NASA NTRS1983

Fabrication of low-cost Mod-OA wood composite wind turbine blades

The wood composite blades were fabricated by using epoxy resin-bonded laminates of Douglas fir veneers for the leading edge spar sections and honeycomb-cored birch plywood panels for the blade trailing edge or afterbody sections. The blade was joined to the wind turbine hub assembly by epoxy resin-bonded steel load take-off studs. The wood composite blades were installed in the Mod-OA wind turbine test facility at Kahuku, Hawaii. The wood composite blades have successfully completed high power (average of 150 kW) operations for an eighteen month period (nearly 8,000 hr) before replacement with another set of wood composite blades. The original set of blades was taken out of service because of the failure of the shank on one stud. An inspection of the blades at NASA-Lewis showed that the shank failure was caused by a high stress concentration at a corrosion pit on the shank fillet radius which resulted in fatigue stresses in excess of the endurance limit.

Lark, R. F.↗

NASA NTRS1991

Raman shifting of KrF laser radiation for tropospheric ozone measurements

The differential absorption lidar (DIAL) measurement of tropospheric ozone requires use of high average power UV lasers operating at two appropriate DIAL wavelengths. Laboratory experiments have demonstrated that a KrF excimer laser can be used to generate several wavelengths with good energy conversion efficiencies by stimulated Raman shifting using hydrogen (H2) and deuterium (D2). Computer simulations for an airborne lidar have shown that these laser emissions can be used for the less than 5 percent random error, high resolution measuremment of ozone across the troposphere using the DIAL technique. In the region of strong ozone absorption, laser wavelengths of 277.0 and 291.7 nm were generated using H2 and D2, respectively. In addition, a laser wavelength at 302.0 nm was generated using two cells in series, with the first containing D2 and the second containing H2. The energy conversion efficiency for each wavelength was between 14 and 27 percent.

Grant, William B.↗

NASA NTRS1984

Applications of excimer lasers for atmospheric species measurements

Excimer lasers are proven sources of high pulse energy and high average power coherent radiation at several wavelength regions throughout the ultraviolet spectrum. If designed properly, excimer lasers can be operated with both low divergence and narrow spectral bandwidth, and using an oscillator - injection-locked amplifier configuration they can be tuned over a 10 to 20 A bandwidth without appreciable loss in energy. Additional wavelength coverage from excimer lasers can be obtained by stimulated Raman scattering. With the development of magnetic switching for the high voltage, high power switches, the electric discharge excimer laser can also be operated reliably for extended periods of time at high pulse rates. All these features make excimer lasers ideal sources of ultraviolet radiation for a variety of remote and in-situ atmospheric species measurements.

Laudenslager, J. B.↗

NASA NTRS1973

Gas lasers and applications

A brief review of laser elements is given. Flowing gas lasers are represented to have the best potential for high average power. The background of shock-tube researchers and the shock tube itself are alleged to be ideally suited for the development of such lasers. Three types - the electric discharge, the gasdynamic, and the chemical laser - are discussed briefly. A legion number of possible gas lasers is enumerated. With the development of their potential for higher power and efficiency, many additional and important uses of lasers are predicted, even beaming power through space for long distances, up to 1 AU. A few details of some current high-power gasdynamic laser devices are given.

Hansen, C. F.↗

NASA NTRS1989

Frequency stable high power lasers in space

The concept of a laser heterodyne gravity wave antenna that would operate in solar orbit with a one million kilometer path length is discussed. Laser technology that would be appropriate for operation of this space-based gravity wave detector is also discussed. The rapid progress in diode laser coupled with the energy storage and potentially sub-Hertz linewidths of solid state lasers, and the possibility of efficient frequency conversion by nonlinear optical techniques defines a technology that is appropriate for laser interferometry in space. The present status of diode-laser-pumped, solid state lasers is summarized and future progress is projected in areas of linewidth control, high average power, operating efficiency, and operational lifetimes that are essential for space-based applications.

Byer, Robert L.↗

DOE OSTI2026

Influence of Oxygen Flow and Stoichiometry on Optical Properties and Damage Resistance of Hafnium Oxide Thin Films

Hafnium oxide (HfO 2 ) is predominantly used as a high-index material in multi-layer dielectric coatings for high-peak- and high-average-power lasers, but laser damage often initiates within the HfO 2 layers despite their wide bandgap. Oxygen deficiency during deposition can introduce vacancy-related sub-bandgap states and absorptive defects, lowering damage resistance. This study investigates how oxygen flow during HfO 2 deposition with ion beam sputtering (IBS) affects its stoichiometry, defect formation, and nanosecond laser-induced damage threshold (LIDT) and whether single-layer trends predict multilayer performance. Single layers were deposited at varying oxygen flows, characterized for optical and structural properties, and tested for the LIDT at 1064 nm and 355 nm. Increasing oxygen flow drove the layer toward near-stoichiometric HfO 2 , reduced the refractive index, and altered the density of surface pinhole-like features. The single-layer LIDT at 355 nm increased with oxygen, whereas the 1064 nm LIDT was comparatively less sensitive to oxygen flow, consistent with the wavelength-dependent roles of absorptive precursors and microstructural defects. In contrast, a HfO 2 -based high-reflector (HR) showed a higher LIDT at lower oxygen flow, indicating that the family of damage precursors changes between single layers and multilayers; in stacks, structural properties such as stress, gas entrapment and thermal dissipation may outweigh the isolated absorptive defects found in single layers. These results demonstrate that the optimal oxygen flow condition depends on both LIDT wavelength and film architecture. We identified, for single layers, a 15–35 sccm window for maximizing the 1064 nm LIDT and a high-flow optimum (45 sccm) for the 355 nm LIDT and, for 355 nm HR stacks, a distinct lower-flow regime (~10 sccm).

Optics and optical instruments↗

DOE OSTI2025

Status and prospects for inertial fusion energy via lasers

Fusion energy is the ultimate clean and limitless energy source, but its development requires overcoming many scientific and technological challenges. For the first time in the 60-year long history of fusion research, ignition and target gain above unity (G>1) were demonstrated in the laboratory at the National Ignition Facility at the Lawrence Livermore National Laboratory in 2022. Turning laser fusion into an energy source requires that the results from single shot experiments be replicated at much higher repetition rates of many shots per second to produce high average power at relatively low cost. Furthermore, this requires the development of new laser technologies, mass production of suitable targets, accurate injection and tracking systems and new materials for the reactor chamber components and final optics. Ultra broadband and deep UV light are laser advances that can dramatically improve the laser energy coupling to the target thereby reducing the laser energy and power requirements.

Fusion energy↗

DOE OSTI2024

Collaborative Research: Enhancing Laser-Based Ion Sources with High Data Rate Techniques

This collaborative research project focuses on leveraging advanced machine learning techniques to analyze and optimize data from high-repetition-rate laser experiments. The main goal is to apply modern computing hardware, customized data acquisition firmware/software, and machine learning approaches to improve data analysis and experimental control. The project also explores how methodology can be developed on smaller-scale experimental setups and then translated to larger facilities within DOE's LaserNetUS network. With extensive data collection and modeling, the research aims to predict and optimize experimental parameters to enhance performance and efficiency.

47 OTHER INSTRUMENTATION↗

NASA NTRS1980

Infrared heterodyne receivers with IF responses approaching 5 GHz

Specialized coherent 10.6 micrometer infrared receivers were developed with infrared frequency responses approaching 5 GHz. Carbon dioxide lasers were employed for these applications because of their availability, stability, and high average power levels. Heterodyne receivers which employ extrinsic photoconductive Ge:Cu(Sb) mixers were developed for measurements of carbon dioxide laser scattering to determine: (1) the drive lower hybrid wave density fluctuations; and (2) the plasma ion temperature of the dense Tokamak plasmas.

Wolczok, J. M.↗

NASA NTRS1985

Efficient frequency conversion of laser sources in nonlinear crystals

The use of nonlinear crystals to extend the frequency range of solid-state laser sources is proposed. The harmonic generation of high-average-power laser sources and CW-laser-sources nonlinear crystals is considered. The development of Nd:YAG pumped parametric oscillators and optical parametric amplifiers using LiNbO3 or AgGaS2 is studied. The LiNbO3 oscillator has tunable output over the 1.4-4.0 micron range and is applicable for remote sensing measurements of molecules and of humidity and temperature; AgGaS2 oscillators provide the potential for 3-15 micron infrared generation. Advances in material synthesis techniques related to the design and synthesis of nonlinear media are discussed. Various procedures for the synthesis of nonlinear crystals are described.

Byer, R. L.↗

NASA NTRS2010

Laser ablation for the synthesis of carbon nanotubes

Single walled carbon nanotubes are produced in a novel apparatus by the laser-induced ablation of moving carbon target. The laser used is of high average power and ultra-fast pulsing. According to various preferred embodiments, the laser produces an output above about 50 watts/cm.sup.2 at a repetition rate above about 15 MHz and exhibits a pulse duration below about 10 picoseconds. The carbon, carbon/catalyst target and the laser beam are moved relative to one another and a focused flow of side pumped, preheated inert gas is introduced near the point of ablation to minimize or eliminate interference by the ablated plume by removal of the plume and introduction of new target area for incidence with the laser beam. When the target is moved relative to the laser beam, rotational or translational movement may be imparted thereto, but rotation of the target is preferred.

Holloway, Brian C.↗

NASA NTRS2012

Laser ablation for the synthesis of carbon nanotubes

Single walled carbon nanotubes are produced in a novel apparatus by the laser-induced ablation of moving carbon target. The laser used is of high average power and ultra-fast pulsing. According to various preferred embodiments, the laser produces and output above about 50 watts/cm.sup.2 at a repetition rate above about 15 MHz and exhibits a pulse duration below about 10 picoseconds. The carbon, carbon/catalyst target and the laser beam are moved relative to one another and a focused flow of "side pumped", preheated inert gas is introduced near the point of ablation to minimize or eliminate interference by the ablated plume by removal of the plume and introduction of new target area for incidence with the laser beam. When the target is moved relative to the laser beam, rotational or translational movement may be imparted thereto, but rotation of the target is preferred.

Holloway, Brian C.↗

DOE OSTI2025

Century: Zap Energy’s 100-kW-Scale Repetitive Sheared-Flow-Stabilized Z -Pinch System with Liquid Metal Cooling

Zap Energy is developing the sheared-flow-stabilized (SFS) Z-pinch concept for commercial applications. The SFS Z pinch relies on plasma self-organization, in the sense that plasma dynamics play a critical role in confinement. Using plasma axial current for confinement and compression eliminates the need for external confinement or heating technologies. This compact magnetic confinement technology could, in turn, provide the basis for a cost-effective deuterium-tritium fusion power plant. In addition to a robust experimental program pushing plasma performance towards breakeven conditions, Zap Energy has parallel programs developing power handling systems suitable for future power plants. Technologies under development include high average-power repetitive pulsed power, high duty-cycle cathodes, and liquid metal wall systems. Century is the name of Zap Energy’s first effort to integrate these three components into an operational system capable of firing non-reacting hydrogen SFS Z-pinch plasmas into a liquid-metal-lined container at sustained repetition rates on the order of 0.1 Hz. Here, the pulsed power driver and liquid metal heat exchanger are both designed to sustain input powers of 100 kW. Construction and initial operations with an interim ~10 kW liquid metal heat exchanger are described.

Century↗

DOE OSTI2025

Tailoring coherent beam combined laser pulse trains for high peak and average power applications

Laser systems based on coherent beam combination (CBC) that rely on tiled pupil architecture intrinsically carry digital capabilities independently applicable to all three essential characteristics of a laser pulse: amplitude, phase and polarization. Those capabilities allow the far-field energy distribution to be flexibly tailored in real time. Operation in the femtosecond regime at high repetition rates gives access to a wide range of applications requiring both high peak and average powers. We address the task of independent peak versus average power adjustment needed for applications seeking to decouple nonlinear phenomena associated with GW peak power from the thermal load inherent to kW average power operation. The technical solutions proposed are presented in the framework of the Ecole Polytechnique XCAN CBC laser platform (61 independent channels) with an emphasis on thermal management measures implemented to ensure its nominal operation.

47 OTHER INSTRUMENTATION↗

DOE OSTI2025

Impact of high-temperature annealing on hafnia-silica composite coatings deposited via ion beam sputtering for high-peak power 1064 nm lasers

The maximum power handling fluence of high-peak and average power laser systems is often limited by the laser damage of the coatings on optical components. Furthermore, these multilayer dielectric coatings are limited in their maximum power handling due to laser-damage-prone defects in the lower optical bandgap, higher optical index material. Some of these defects can be mitigated by thermal annealing to high temperatures, which can greatly reduce the linear absorbative precursors. Typically, hafnia and silica are the materials of choice for high-peak and average power laser systems in the ultraviolet through infrared spectral range; however, hafnia crystalizes readily when annealed at high temperatures. In this study, we prepare composite HfO 2 -SiO 2 coatings by co-sputtering hafnia and silica in an ion beam sputtering system and compare them to pure hafnia-based coatings. We demonstrate that crystallinity in hafnia can be completely suppressed when it is mixed with silica, such as the composite coatings in this study. High reflectors were fabricated and annealed, demonstrating that the multilayer dielectric stacks can survive high-temperature annealing and exhibit an excellent linear absorption of 0.2 +/- 1 ppm at 1064 nm. Short- and long-pulse laser damage was explored, demonstrating the complex relationship between linear absorption and the non-linear absorption which drives pulsed laser damage. These results provide an excellent route to the creation of very low linear absorption optical coatings, which also utilize low scattering materials that are best suited for high-peak and average power applications.

Harthcock, Colin [Lawrence Livermore National Labo↗