Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “helium bubbles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Effects of vortex flaps on the low-speed aerodynamic characteristics of an arrow wing

Tests were conducted in the Langley 12-foot low-speed wind-tunnel to determine the longitudinal and lateral-directional aerodynamic effects of plain and tabbed vortex flaps on a flat-plate, highly swept arrow-wing model. Flow-visualization studies were made using a helium-bubble technique. Static forces and moments were measured over an angle-of-attack range from 0 deg to 50deg for sideslip angles of 0 deg and + or - 4 deg.

Yip, L. P.↗
NASA NTRS1982

Dynamic load measurements with delta wings undergoing self-induced roll-oscillations

The aerodynamic forces acting on a delta wing, mounted on a free-to-roll sting-balance apparatus, were measured. Two wing planforms having leading edge sweeps of 76 and 80 deg were tested, but only the wing with the 80 deg sweep would undergo periodic self-induced roll oscillation. The time dependent forces and roll angles for this wing were then recorded for various test conditions. In these tests a considerable drop in the average normal force of the free-to-roll wing was measured, relative to the normal force obtained in the static tests. Also, the helium-bubble flow visualization technique was used to gain some insight into the periodic motion of the separated leading edge vortices.

Levin, D.↗
NASA NTRS1985

An exploratory study of apex fence flaps on a 74 deg delta wing

An exploratory wind tunnel investigation was performed to observe the flow field effects produced by vertically deployed apex fences on a planar 74 degree delta wing. The delta shaped fences, each comprising approximately 3.375 percent of the wing area, were affixed along the first 25 percent of the wing leading edge in symmetric as well as asymmetric (i.e., fence on one side only) arrangements. The vortex flow field was visualized at angles of attack from 0 to 20 degrees using helium bubble and oil flow techniques; upper surface pressures were also measured along spanwise rows. The results were used to construct a preliminary description of the vortex patterns and induced pressures associated with vertical apex fence deployment. The objective was to obtain an initial evaluation of the potential of apex fences as vortex devices for subsonic lift modulation as well as lateral directional control of delta wing aircraft.

Wahls, R. A.↗
NASA NTRS1986

Lateral jet injection into typical combustor flowfields

The experimental problem of lateral jet injection into typical flow fields in the absence of combustion was studied. All flow fields being investigated have no expansion of the crossflow (the test section to swirler diameter ratio D/d = 1), after its passage through an optional swirler (with swirl vane angle phi = 0 (swirler removed), 45, and 70 degree). The lateral jet(s) is(are) located one test-section diameter downstream of the test-section inlet (x/D = 1). The lateral jets have round-sectioned nozzles, each of which has an area of 1/100th of the cross sectional area of the crossflow (A sub j/A sub c = 1/100). Jet-to-crossflow velocity ratios of R = v sub j/u sub o = 2, 4, and 6 were investigated. Helium-bubble low visualization, five-hole pitot probe time-mean velocity measurements, and single-wire time-mean velocity and normal and shear stress turbulence data were obtained in the research program.

Lilley, D. G.↗
NASA NTRS1988

Effects of surface perturbations on the asymmetric vortex flow over a slender body

An experimental investigation of the effects of surface perturbations on the asymmetric flow past a slender body has been conducted for laminar flow conditions. Beads with diameters ranging from 3/32 to 12/32 in. were attached near the apex of a cone/cylinder model having a base diameter of 3.5 in. and a cone semiapex angle of 9 deg at an angle of attack of 40 deg in an attempt to alter the sense of the asymmetric vortex flow pattern. Circumferential position as well as longitudinal location were varied to determine the most effective bead position. Whether or not the beads were effective in controlling the magnitude and direction of the vortex asymmetries was determined by 3 circumferential rows of pressure taps and by a helium-bubble flow visualization technique. The most effective circumferential position was found to be approximately 140 deg from the windward ray. While holding this circumferential position constant, the effect of bead size at three stations further along the body was also investigated. It was found that the size of the bead necessary to reverse the asymmetry increased more rapidly than the growth in cylinder radius. In general, these results indicate that discrete geometric imperfections on a body's surface can force asymmetry in a given direction if they are sufficiently large relative to the local radius.

Moskovitz, Cary A.↗
NASA NTRS1990

Experimental investigation of a new device to control the asymmetric flowfield on forebodies at large angles of attack

An exploratory experimental investigation of a new device to control the asymmetric flowfield on forebodies at large angles of attack has been conducted. The device is a rotatable forebody tip, which varies in cross section from circular at its base to elliptic at its tip. The device itself extends over a small portion of the aircraft or missile forebody. The device provides two important improvements. First, it replaced the normally random behavior of the nose side force as a function of nose tip orientation with a predictable and generally sinusoidal distribution and, second, the device showed promise for use as part of a vehicle control system, to be deflected in a prescribed manner to provide additional directional control for the vehicle. The device was tested on a cone/cylinder model having a 10 deg semiapex angle and on a 3.0 caliber tangent ogive model, each with a base diameter of 3.5 in, for angles of attack from 30 to 60 deg. Data were taken from 3 circumferential rows of pressure taps on each model at a Reynolds number of 84,000 based on cylinder diameter and by a helium-bubble flow visualization technique at a Reynolds number of 24,000.

Moskovitz, Cary A.↗
NASA NTRS1990

A survey of techniques for refrigeration, reliquefaction, and production of slush for hydrogen

Several techniques were surveyed for the refrigeration, reliquefaction and production of slush from hydrogen. The techniques included auger; bubbling helium gas; Simon desorption; the Petlier effect; Joule-Kelvin expansion using Stirling, Brayton, and Viulleumirer approaches; rotary reciprocating; a dilution refrigerator; adiabatic demagnetization of a paramagnetic salt; and adiabatic magnetization of a superconductor.

Overcash, Dan R.↗
NASA NTRS1991

Effect of a simulated ice accretion on the aerodynamics of a swept wing

The effect of a simulated glaze ice accretion on the aerodynamic performance of a three-dimensional swept wing is studied experimentally. A semispan wing of effective aspect ratio four was mounted from the sidewall of the UIUC subsonic wind tunnel. The model uses a NACA 0012 airfoil section on a rectangular planform with interchangeable tip and root sections to allow for 0- and 30-degree sweep. A sidewall suction system is used to minmize the tunnel boundary-layer interaction with the model. Surface pressure data from five spanwise stations are compared to earlier data from a similar tunnel. A three-component sidewall balance has been designed, built and used to measure lift, drag and pitching moment on the clean and iced model. The data compare well to the integrated pressure data and to theory on the clean model. In addition, helium-bubble flow visualization has been performed on the iced model and reveals extensive spanwise flow in the separation bubble aft of the upper surface horn. This compares well to the computational results of other researchers. Sidewall suction was found to have no effect on the aerodynamics of the swept wing.

Bragg, M. B.↗
NASA NTRS1992

Stability test and analysis of the Space Shuttle Primary Reaction Control Subsystem thruster

The results are reported of a test program conducted on the Space Shuttle Primary Reaction Control Subsystem thruster in order to investigate the effects of trapped helium bubbles and saturated propellants on stability, determine if thruster-to-thruster stability variations are significant, and determine stability under STS-representative conditions. It is concluded that the thruster design is highly reliable in flight and that burn-through has not occurred. Significantly unstable thrusters are screened out, and wire wrap is found to protect against chamber burn-throughs and to provide a fail-safe thruster for this situation.

Applewhite, John↗
NASA NTRS1992

Flow visualizations of perpendicular blade vortex interactions

Helium bubble flow visualizations have been performed to study perpendicular interaction of a turbulent trailing vortex and a rectangular wing in the Virginia Tech Stability Tunnel. Many combinations of vortex strength, vortex-blade separation (Z(sub s)) and blade angle of attack were studied. Photographs of representative cases are presented. A range of phenomena were observed. For Z(sub s) greater than a few percent chord the vortex is deflected as it passes the blade under the influence of the local streamline curvature and its image in the blade. Initially the interaction appears to have no influence on the core. Downstream, however, the vortex core begins to diffuse and grow, presumably as a consequence of its interaction with the blade wake. The magnitude of these effects increases with reduction in Z(sub s). For Z(sub s) near zero the form of the interaction changes and becomes dependent on the vortex strength. For lower strengths the vortex appears to split into two filaments on the leading edge of the blade, one passing on the pressure and one passing on the suction side. At higher strengths the vortex bursts in the vicinity of the leading edge. In either case the core of its remnants then rapidly diffuse with distance downstream. Increase in Reynolds number did not qualitatively affect the flow apart from decreasing the amplitude of the small low-frequency wandering motions of the vortex. Changes in wing tip geometry and boundary layer trip had very little effect.

Rife, Michael C.↗
NASA NTRS1996

Turbulent Inflow Measurements

In the present research, tilt rotor aeroacoustics have been studied experimentally and computationally. Experimental measurements were made on a 1/12.5 scale model. A dimensional analysis showed that the model was a good aeroacoustic approximation to the full-scale aircraft, and scale factors were derived to extrapolate the model measurements to the full-scale XV-15. The experimental measurements included helium bubble flow visualization, silk tuft flow visualization, 2-component hot wire anemometry, 7-hole pressure probe measurements, vorticity measurements, and outdoor far field acoustic measurements. The hot wire measurements were used to estimate the turbulence statistics of the flow field into the rotors, such as length scales, velocity scales, dissipation, and turbulence intermittency. To date, these flow measurements are the only ones in existence for a hovering tilt rotor. Several different configurations of the model were tested: (1) standard configurations (single isolated rotor, two rotors without the aircraft, standard tilt rotor configuration); (2) flow control devices (the 'plate', the 'diagonal fences'); (3) basic configuration changes (increasing the rotor/rotor spacing, reducing the rotor plane/wing clearance, operating the rotors out of phase). Also, an approximation to Sikorsky's Variable Diameter Tilt Rotor (VDTR) configuration was tested, and some flow measurements were made on a semi-span configuration of the model. Acoustic predictions were made using LOWSON.M, a Mathematica code. This hover prediction code, from HOVER.FOR, used blade element theory for the aerodynamics, and Prandtl's Vortex theory to model the wake, along with empirical formulas for the effects of Reynolds number, Mach number, and stall. Aerodynamic models were developed from 7-hole pressure probe measurements of the mean velocity into the model rotors. LOWSON.M modeled a rotor blade as a single force and source/sink combination separated in the chordwise direction, at an effective blade radius. Spanwise, Mach-weighted integrals were used to find the equivalent forces and equivalent source strengths.

George, Albert R.↗
NASA NTRS1996

Tilt Rotor Aircraft Aeroacoustics

A fleet of civil tilt rotor transports offers a means of reducing airport congestion and point-to-point travel time. The speed, range, and fuel economy of these aircraft, along with their efficient use of vertiport area, make them good candidates for short-to-medium range civil transport. However, to be successfully integrated into the civilian community, the tilt rotor must be perceived as a quiet, safe, and economical mode of transportation that does not harm the environment. In particular, noise impact has been identified as a possible barrier to the civil tilt rotor. Along with rotor conversion-mode flight, and blade-vortex interaction noise during descent, hover mode is a noise problem for tilt rotor operations. In the present research, tilt rotor hover aeroacoustics have been studied analytically, experimentally, and computationally. Various papers on the subject were published as noted in the list of publications. More recently, experimental measurements were made on a 1/12.5 scale model of the XV-15 in hover and analyses of this data and extrapolations to full scale were also carried out. A dimensional analysis showed that the model was a good aeroacoustic approximation to the full-scale aircraft, and scale factors were derived to extrapolate the model measurements to the full-scale XV-15. The experimental measurements included helium bubble flow visualization, silk tuft flow visualization, 2-component hot wire anemometry, 7-hole pressure probe measurements, vorticity measurements, and outdoor far field acoustic measurements. The hot wire measurements were used to estimate the turbulence statistics of the flow field into the rotors, such as length scales, velocity scales, dissipation, and turbulence intermittency. Several different configurations of the model were tested: (1) standard configurations (single isolated rotor, two rotors without the aircraft, standard tilt rotor configuration); (2) flow control devices (the 'plate', the 'diagonal fences'); (3) basic configuration changes (increasing the rotor/rotor spacing, reducing the rotor plane/wing clearance. operating the rotors out of phase). Also, an approximation to Sikorsky's Variable Diameter Tilt Rotor (VDTR) configuration was tested, and some flow measurements were made on a semi-span configuration of the model. Acoustic predictions were made using LOWSON.M, a Mathematica code Mean aerodynamic models were developed based on hover performance predictions from HOVER.FOR. This hover prediction code used blade element theory for the aerodynamics, and Prandtl's Vortex theory to model the wake, along with empirical formulas for the effects of Reynolds number, Mach number, and stall. Aerodynamic models were developed from 7-hole pressure probe measurements of the mean velocity into the model rotors.

George, Albert R.↗
NASA NTRS1999

Sensitized Liquid Hydrazine Detonation Studies

Vapor-phase hydrazine (N2H4) is known to be very sensitive to detonation while liquid hydrazine is very insensitive to detonation, theoretically requiring extremely high pressures to induce initiation. A review of literature on solid and liquid explosives shows that when pure explosive substances are infiltrated with gas cavities, voids, and/or different phase contaminants, the energy or shock pressure necessary to induce detonation can decrease by an order of magnitude. Tests were conducted with liquid hydrazine in a modified card-gap configuration. Sensitization was attempted by bubbling helium gas through and/or suspending ceramic microspheres in the liquid. The hydrazine was subjected to the shock pressure from a 2 lb (0.9 kg) Composition C-4 explosive charge. The hydrazine was contained in a 4 in. (10.2 cm) diameter stainless steel cylinder with a 122 in(sup 3) (2 L) volume and sealed with a polyethylene cap. Blast pressures from the events were recorded by 63 high speed pressure transducers located on three radial legs extending from 4 to 115 ft (1.2 to 35.1 in) from ground zero. Comparison of the neat hydrazine and water baseline tests with the "sensitized" hydrazine tests indicates the liquid hydrazine did not detonate under these conditions.

Rathgeber, K. A.↗
NASA NTRS1968

Reducing bubbles in glass coatings improves electrical breakdown strength

Helium reduces bubbles in glass coatings of accelerator grids for ion thrustors. Fusing the coating in a helium atmosphere creates helium bubbles in the glass. In an argon atmosphere, entrapped helium diffuses out of the glass and the bubbles collapse. The resultant coating has a substantially enhanced electrical breakdown strength.

Banks, B.↗
NASA NTRS1974

Space shuttle orbit maneuvering engine reusable thrust chamber: Adverse operating conditions test report

Test hardware, facilities, and procedures are described along with results of electrically heated tube and channel tests conducted to determine adverse operating condition limits for convectively cooled chambers typical of Space Shuttle Orbit Manuevering Engine designs. Hot-start tests were conducted with corrosion resistant steel and nickel tubes with both monomethylhydrazine and 50-50 coolants. Helium ingestion, in both bubble and froth form, was studied in tubular test sections. Helium bubble ingestion and burn-out limits in rectangular channels were also investigated.

Tobin, R. D.↗
NASA NTRS2026

Thermal Performance of Common Bulk-Fill Cryogenic Insulation Materials in Helium and Hydrogen Background Gases

Maritime shipping of vast quantities of liquid hydrogen (LH 2 ) will be necessary to facilitate a global hydrogen ecosystem; with some studies estimating volumes up to 172,000 m 3 for individual tanker ships, and requiring stationary storage tanks at terminals of 50,000 m 3 to 100,000 m 3 —ten to fifteen times larger than the current largest tank, located at launch pad B at NASA Kennedy Space Center (KSC). Such a radical scale-up will push the boundary of traditional, vacuum-insulated tank designs. Hence, a potential need exists for non-vacuum solutions, which necessitates exploring the thermal performance of insulation materials in non-condensable background gasses at LH 2 temperatures, namely helium and hydrogen. Testing of two bulk-fill insulation materials common to large LH 2 storage tanks, perlite and glass bubbles, in helium and hydrogen was recently conducted by the Cryogenics Test Laboratory at KSC using the Cryostat-100 liquid nitrogen boiloff calorimeter per the ASTM C1774 standard methodology. Effective thermal conductivity (k e ) and heat flux (q) results for each insulation/gas combination are presented across the full vacuum range, as well as thermal profiles through the insulation thickness between 78 K and 293 K.

A M Swanger↗