Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “generator torque controller”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Auxiliary control of LSS

Seven classes of large space structures were identified and idealized into simple geometric shapes which could be easily modelled. Scaling laws were generated which allowed the seven ideal structures to be continuously scaled as to size and mass properties over their respective size ranges. Relevant sources of disturbances were determined and their effects on LSS were compared. These disturbances were applied over the range of scaling parameters to generate control force and torque requirements. Important auxiliary propulsion system (APS) characteristics were identified and an APS characteristic sensitivity matrix was established.

Smith, W.↗
NASA NTRS1988

Adaptive Control For Flexible Structures

Paper discusses ways to cope with measurement noise in adaptive control system for large, flexible structure in outer space. System generates control signals for torque and thrust actuators to turn all or parts of structure to desired orientations while suppressing torsional and other vibrations. Main result of paper is general theory for introduction of filters to suppress measurement noise while preserving stability.

Bayard, David S.↗
NASA NTRS2011

Methodology for Determining Limit Torques for Threaded Fasteners

In aerospace design, where minimizing weight is always a priority, achieving the full capacity from fasteners is essential. To do so, the initial bolt preload must be maximized. The benefits of high preload are well documented and include improved fatigue resistance, a stiffer joint, and resistance to loosening. But many factors like elastic interactions and embedment tend to lower the initial preload placed on the bolt. These factors provide additional motivation to maximize the initial preload. But, to maximize bolt preload, you must determine what torque to apply. Determining this torque is greatly complicated by the large preload scatter generally seen with torque control. This paper presents a detailed methodology for generating limit torques for threaded fasteners. This methodology accounts for the large scatter in preload found with torque control, and therefore, addresses the statistical nature of the problem. It also addresses prevailing torque, a feature common in aerospace fasteners. Although prevailing torque provides a desired locking feature, it can also increase preload scatter. In addition, it can limit the amount of preload that can be generated due to the torsion it creates in the bolt. This paper discusses the complications of prevailing torque and how best to handle it. A wide range of torque-tension bolt testing was conducted in support of this research. The results from this research will benefit the design engineer as well as analyst involved in the design of bolted joints, leading to better, more optimized structural designs.

Hissam, Andy↗
NASA NTRSDate not supplied

Attitude Control System for the Solar Cruiser and Future Solar Sail Missions

NASA’s Marshall Space Flight Center (MSFC) is developing the Solar Cruiser solar sail mission to continue to mature solar sail propulsion. Solar Cruiser is a 95kg spacecraft capable of deploying a 1654 square meter solar sail. Solar Cruiser will demonstrate science observation capabilities and navigation in sub Lagrange Point (L1) halo-orbits. Solar Cruiser sail technology can be scaled to larger solar sail missions, including attitude control system and sail membrane and boom technology. Larger solar sails could be used to image the solar poles, enabling Solar Polar Imager (SPI) missions currently prohibitively expensive for propellant-based propulsion methods. Similarly, solar sails can be used to create artificial equilibria and indefinite station-keeping at locations sunward of Lagrange Point one, L1, along the Sun-Earth line (SEL), which can provide space-weather monitor and prediction and reveal discoveries about our Sun and solar system. To achieve the high characteristic acceleration required for larger solar sail missions such as SPI, a solar sail area of approximately 7000 square-meters would be needed. In comparison, the largest solar sail flown to date is the JAXA’s IKAROS mission with a 196 square-meters sail. Attitude control an SPI-size sail poses challenges, including station keeping under solar sail induced torques and thrust vector pointing. In this study, the scalability of the Solar Cruiser sail attitude control architecture to larger sails is studied, such as pointing control performance, mass and power requirements. Solar Cruiser attitude control actuators include propellant-based, such as ion engines, and propellantless options which create differential solar pressures to generate spacecraft torques. Propellantless attitude control includes active translation of the center of mass, Reflectivity Control Devices (RCDs), and tip vanes. The study summarizes the scalability characteristics of the different attitude control architectures for larger solar sail missions.

Solar Sail Propulsion↗
NASA NTRS1995

Control Electronics For Reaction Wheel

Bidirectional operation achieved with single-polarity main power supply. Control circuitry generates pulse-width-modulated 800-Hz waveforms to drive two-phase ac motor and reaction wheel. Operates partly in response to digital magnitude-and-direction torque command generated by external control subsystem and partly in response to tachometric feedback in form of two once-per-revolution sinusoids with amplitudes proportional to speed. Operation in either of two modes called "normal" and "safehold." In normal mode, drive pulses timed so that, on average over one or few cycles, motor applies commanded torque. In safehold mode, pulses timed to keep motor running at set speed in one direction.

Chamberlin, Keith↗
NASA NTRS1987

Computerized Torque Control for Large dc Motors

Speed and torque ranges in generator mode extended. System of shunt resistors, electronic switches, and pulse-width modulation controls torque exerted by large, three-phase, electronically commutated dc motor. Particularly useful for motor operating in generator mode because it extends operating range to low torque and high speed.

Willett, Richard M.↗
NASA NTRS1978

Accuracy analysis of pointing control system of solar power station

The first-phase effort concentrated on defining the minimum basic functions that the retrodirective array must perform, identifying circuits that are capable of satisfying the basic functions, and looking at some of the error sources in the system and how they affect accuracy. The initial effort also examined three methods for generating torques for mechanical antenna control, performed a rough analysis of the flexible body characteristics of the solar collector, and defined a control system configuration for mechanical pointing control of the array.

Hung, J. C.↗
NASA NTRS2004

Lightweight Exoskeletons with Controllable Actuators

A proposed class of lightweight exoskeletal electromechanical systems would include electrically controllable actuators that would generate torques and forces that, depending on specific applications, would resist and/or assist wearers movements. The proposed systems would be successors to relatively heavy, bulky, and less capable human-strength-amplifying exoskeletal electromechanical systems that have been subjects of research during the past four decades. The proposed systems could be useful in diverse applications in which there are needs for systems that could be donned or doffed easily, that would exert little effect when idle, and that could be activated on demand: examples of such applications include (1) providing controlled movement and/or resistance to movement for physical exercise and (2) augmenting wearers strengths in the performance of military, law-enforcement, and industrial tasks. An exoskeleton according to the proposal would include adjustable lightweight graphite/epoxy struts and would be attached to the wearer's body by belts made of hook-and-pile material. At selected rotary and linear joints, the exoskeleton would be fitted, variously, with lightweight, low-power-consumption rotary and linear brakes, clutches, and motors. The exoskeleton would also be equipped with electronic circuitry for monitoring, control, and possibly communication with external electronic circuits that would perform additional monitoring and control functions.

Bar-Cohen, Yoseph↗
NASA NTRS1979

Design of reduced-order controllers for large flexible space structures

Several approaches to the design of reduced-order controllers for large space structures are discussed. The approaches are based on linear-quadratic-Gaussian (LQG) control theory and include truncation, singular perturbation regulator and estimator, direct sensor feedback, higher-order estimator, and selective suppression of some of the uncontrolled or 'residual' modes. Numerical results are given for a long free-free beam. Sufficient conditions for stability in the presence of control and observation spillovers are outlined. It is shown that the system considered can be satisfactorily controlled using a single torque generator and one attitude and one rate sensor.

Joshi, S. M.↗
NASA NTRS1995

Variable speed generator application on the MOD-5A 7.3 mW wind turbine generator

This paper describes the application of a Scherbiustat type variable speed subsystem in the MOD-5A Wind Turbine Generator. As designed by General Electric Company, Advanced Energy Programs Department, under contract DEN3-153 with NASA Lewis Research Center and DOE, the MOD-5A utilizes the subsystem for both starting assistance in a motoring mode and generation in a controlled airgap torque mode. Reactive power control is also provided. The Scherbiustat type arrangement of a wound rotor machine with a cycloconverter in the rotor circuit was selected after an evaluation of variable speed technologies that followed a system evaluation of drivetrain cost and risk. The paper describes the evaluation factors considered, the results of the evaluations and summarizes operating strategy and performance simulations.

Barton, Robert S.↗
NASA NTRS2000

Postural control model interpretation of stabilogram diffusion analysis

Collins and De Luca [Collins JJ. De Luca CJ (1993) Exp Brain Res 95: 308-318] introduced a new method known as stabilogram diffusion analysis that provides a quantitative statistical measure of the apparently random variations of center-of-pressure (COP) trajectories recorded during quiet upright stance in humans. This analysis generates a stabilogram diffusion function (SDF) that summarizes the mean square COP displacement as a function of the time interval between COP comparisons. SDFs have a characteristic two-part form that suggests the presence of two different control regimes: a short-term open-loop control behavior and a longer-term closed-loop behavior. This paper demonstrates that a very simple closed-loop control model of upright stance can generate realistic SDFs. The model consists of an inverted pendulum body with torque applied at the ankle joint. This torque includes a random disturbance torque and a control torque. The control torque is a function of the deviation (error signal) between the desired upright body position and the actual body position, and is generated in proportion to the error signal, the derivative of the error signal, and the integral of the error signal [i.e. a proportional, integral and derivative (PID) neural controller]. The control torque is applied with a time delay representing conduction, processing, and muscle activation delays. Variations in the PID parameters and the time delay generate variations in SDFs that mimic real experimental SDFs. This model analysis allows one to interpret experimentally observed changes in SDFs in terms of variations in neural controller and time delay parameters rather than in terms of open-loop versus closed-loop behavior.

NASA Program Biomedical Research and Countermeasur↗
NASA NTRS1982

Space telescope pointing control system

The Space Telescope is a free-flying spacecraft designed for Space Shuttle launch. The Space Telescope's pointing control system slews the optical axis from one target star region of the celestial sphere to the next, and maintains precision pointing for the target star for up to 24 hours. The spacecraft digital computer processes the precision attitude and rate sensor data to generate torque commands for the reaction wheels. The pointing control system has four major elements: the command generator, the control system, the attitude reference processing, and momentum management. The emphasis is on relating design requirements to the hardware and software implementation.

Dougherty, H.↗
NASA NTRS1973

In-orbit performance of the ITOS improved attitude control system with Hall generator brushless motor and earth-splitting technique

The National Aeronautics and Space Administration (NASA), launched ITOS-D with an improved attitude control system. A Hall generator brushless dc torque motor replaced the brush dc torque motor on Tiros-M and ITOS-A. Two CO2 attitude horizon sensors and one mirror replaced the four wideband horizon sensors and two mirrors on ITOS-1 and NOAA-1. Redundant pitch-control electronic boxes containing additional electronic circuitry for earth-splitting and brushless motor electronics were used. A method of generating a spacecraft earth-facing side reference for comparison to the time occurrence of the earth-splitting pulse was used to automatically correct pitch-attitude error. A single rotating flywheel, supported by a single bearing, provided gyroscopic stability and the required momentum interchange to keep one side of the satellite facing the earth. Magnetic torquing against the earth's magnetic field eliminated the requirement for expendable propellants which would limit satellite life in orbit.

Peacock, W. M.↗
NASA NTRS1984

Space Telescope pointing control

The Space Telescope, a long life, high performance spacecraft deployed by the Space Shuttle, will carry five scientific instruments on its first mission. Its pointing control system will permit target-to-target maneuvering and precision pointing on a target star to support scientific objectives. Spacecraft attitude control is achieved by onboard computer processing of attitude and rate sensor data to generate reaction wheel torque commands. A momentum management control system is provided to desaturate the reaction wheels. This paper discusses the pointing control system and the control hardware investigations and improvements leading to system design.

Dougherty, H.↗
NASA NTRS1982

Development of closed loop roll control for magnetic balance systems

This research was undertaken with the goal of demonstrating closed loop control of the roll degree of freedom on the NASA prototype magnetic suspension and balance system at the MIT Aerophysics Laboratory, thus, showing feasibility for a roll control system for any large magnetic balance system which might be built in the future. During the research under this grant, study was directed toward the several areas of torque generation, position sensing, model construction and control system design. These effects were then integrated to produce successful closed loop operation of the analogue roll control system. This experience indicated the desirability of microprocessor control for the angular degrees of freedom.

Covert, E. E.↗
NASA NTRS1980

Kinesthetic coupling between operator and remote manipulator

A universal force-reflecting hand controller has been developed which allows the establishment of a kinesthetic coupling between the operator and a remote manipulator. The six-degree-of-freedom controller was designed to generate forces and torques on its three positional and three rotational axes in order to permit the operator to accurately feel the forces encountered by the manipulator and be as transparent to operate as possible. The universal controller has been used in an application involving a six-degree-of-freedom mechanical arm equipped with a six-dimensional force-torque sensor at its base. In this application, the hand controller acts as a position control input device to the arm, while forces and torques sensed at the base of the mechanical hand back drive the hand controller. The positional control relation and the back driving of the controller according to inputs experienced by the force-torque sensor are established through complex mathematical transformations performed by a minicomputer. The hand controller is intended as a development tool for investigating force-reflecting master-slave manipulator control technology.

Bejczy, A. K.↗