Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fuel swelling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Theoretical analysis of swelling characteristics of cylindrical uranium dioxide fuel pins with a niobium - 1-percent-zirconium clad

The relations between clad creep strain and fuel volume swelling are shown for cylindrical UO2 fuel pins with a Nb-1Zr clad. These relations were obtained by using the computer code CYGRO-2. These clad-strain - fuel-volume-swelling relations may be used with any fuel-volume-swelling model, provided the fuel volume swelling is isotropic and independent of the clad restraints. The effects of clad temperature (over a range from 118 to 1642 K (2010 to 2960 R)), pin diameter, clad thickness and central hole size in the fuel have been investigated. In all calculations the irradiation time was 500 hours. The burnup rate was varied.

Saltsman, J. F.↗
DOE OSTI2025

Mechanistic nuclear fuel performance modeling of uranium nitride

Uranium mononitride (UN) is a nuclear fuel candidate for advanced reactor designs and an alternative being considered for light water reactors due to its higher thermal conductivity and uranium density than UO 2 . As with any nuclear fuel, swelling and fission gas release are important factors for safety, while also being some of the hardest phenomena to predict with a high degree of confidence. Getting a grasp on the gas swelling behavior and release is crucial to lower the barrier for UN utilization. An accelerated swelling rate at high temperatures observed experimentally, sometimes referred to as “breakaway swelling,” further complicates the prediction of fuel performance of UN. A mechanistic model has been developed using a multiscale approach to describe the intragranular and intergranular fission gas behavior. Lower-length-scale calculations have been employed to inform models of the gas and self-diffusion behavior, resolution rate, and bubble shape. Leveraging previous work on high burnup UO 2 , two populations of intragranular bubbles are considered; small bulk bubbles and larger bubbles located along dislocations. The dislocation bubbles were found to be crucial to the overall swelling behavior, and the breakaway swelling transition was associated with the transition in the gas atom diffusion mechanism from an irradiation-induced athermal diffusion regime at lower temperatures to an intrinsic thermal equilibrium regime at higher temperatures, accelerating the growth of the dislocation bubbles. Similarly, the threshold for fission gas release was associated with the grain boundary vacancy diffusivity surpassing the gas atom diffusivity at sufficiently high temperatures, allowing the over-pressurized grain boundary bubble to grow in size and interconnect. Using thermo-mechanical models with the fission gas model, two integral fuel pin assessment cases were simulated. Finally, this work demonstrates the ability of a multiscale approach to accelerate the understanding of advanced fuel forms when experimental data is limited.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Understanding fission gas bubble distribution, lanthanide transportation, and thermal conductivity degradation in neutron-irradiated α-U using machine learning

U—10Zr based metallic nuclear fuel is the leading candidate for next-generation sodium-cooled fast reactors in the United States. US research reactors have used and tested this fuel type since the 1960s and accumulated considerable experience and knowledge about the fuel performance. Most of the knowledge, however, remains empirical. The lack of mechanistic understanding of fuel performance puts a large burden on proof through experimental verification for the qualification of U—10Zr fuel for commercial use. Further, this paper proposes an image data-driven machine learning approach, coupled with domain knowledge provided by advanced post irradiation examination, to provide unprecedented quantified insights into the morphology, size, density and the connectivity of fission gas bubbles and their effects on the fission product transportation and thermal conductivity. Specifically, we developed a method to automatically detect, extract statistics, and classify ~19,000 fission gas bubbles into different categories, and quantitatively link the data to lanthanide transportation through connected bubbles and degradation of thermal conductivity along the radial temperature gradient in a neutron irradiated U—10Zr annular fuel. Results indicate the approach can be modified to study other irradiation effects, such as secondary phase redistribution and gaseous fuel swelling in other irradiated nuclear fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Data Mining – Image Analysis of Radiography for Zr Redistribution

The research effort described in this report represents a first attempt to investigate the radial redistribution of Zr in ternary fuel alloys U-xPu-10Zr (x = 0, 8, 19) irradiated in the in-reactor fuel experiments during the operation of the U.S. Department of Energy’s (DOE’s) Experimental Breeder Reactor II (EBR-II) at Idaho National Laboratory (INL) using methods of image processing on post-irradiation neutron radiographs. Approximately 130,000 metal fuel pins were irradiated in EBR-II during its 30 years of operation to develop and characterize existing and prospective fuels. For many of the metal fuel irradiation experiments, neutron radiography imaging was performed historically now allowing application of modern image analysis techniques to characterize fuel behavior, such as fuel swelling, fluff formation, and now, fuel alloy constituent redistribution. The redistribution of fuel components depends on the temperature field, radially, within the fuel. Specifically, Zr is expected to redistribute radially towards the center of the pin, as well as towards the outer zones. Currently, direct imaging of a pin cross-section through optical methods or scanning electron microscopy (SEM) is used to study the constituents’ redistribution, which is very time-consuming and can only be applied to a limited number of pins. An automated image processing technique allowing for the investigation of fuel radial redistribution zones would significantly accelerate data analysis. In general, if the fuel temperature is hot enough, three redistribution zones are expected, corresponding to the main fuel components (e.g., U, Pu, Zr). While more assessment will be performed in fiscal year (FY)-2023, it seems possible to differentiate the pins according to their fuel composition using image analysis techniques on neutron radiographs of metallic fuel pins based on the analysis to date.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Post-Irradiation Examinations of the ATF Experiments - 2020 Status

This report contains the results of post-irradiation examination (PIE) of both Accident Tolerant Fuels-1 (ATF-1) rodlets and ATF-2 rodlets irradiated in the Advanced Test Reactor (ATR). The experiment is part of the U.S. Department of Energy (DOE) Nuclear Technology Research and Development (NTRD) program’s Advanced Fuels Campaign (AFC). The ATF-1 PIE focused on the continuation of the analyses of five rodlets, one containing U 3 Si 2 fuel, two containing UN-U 3 Si 5 composites, and two with UN-U 3 Si 2 composites. The non-destructive examinations of the U 3 Si 2 rodlet showed results comparable to the previously investigated rodlets. The profilometry of the UN-U 3 Si 2 composites highlighted permanent deformation of the cladding at the pellet-pellet interface, suggesting that hourglassing of the composite pellet occurred during irradiation, causing increased localized stresses on the Zirlo cladding tube due to Pellet-Cladding Mechanical Interaction (PCMI). The UN-U 3 Si 5 rodlets, which were contained in Kanthal cladding, did not show enhanced cladding deformation at the pellet interfaces; however, it is to be noted that the initial gap of these two rodlets was larger than typical light water reactor (LWR) gaps. The larger gap might have been sufficient to accommodate the fuel swelling without having contact between the fuel and cladding, explaining the absence of PCMI. Regarding the fission products, no axial redistribution of the major gamma emitters was observed in any of the composite rodlets. Fission gas measurements on the UN-U 3 Si 5 rodlets also has been performed. The estimated fission gas release, based on the calculated fission product inventory, remains limited, with a higher fission gas release for the rodlet that experienced a higher power.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Characterization of a minor actinides bearing metallic fuel pin irradiated in EBR-II

The X501 transmutation experiment irradiated in Experimental Breeder Reactor II (EBR-II) was intended to evaluate the safety and performance of the addition of minor actinides (Am, Np) into the metallic nuclear fuel system. The irradiation of this experiment is also of paramount importance for comparisons between true fast spectrum irradiations (e.g. EBR-II) and shrouded irradiation capsules performed at the thermal neutron spectrum Idaho National Laboratory Advanced Test Reactor. The X501 experimental fuel pins were irradiated to a peak measured burnup of 6.2% fission per initial heavy metal atom. This paper reports and discusses Postirradiation Examination results for one of two minor actinide bearing pins from the EBR-II X-501 experiment (X501-G591) with a focus on fuel microstructure evolution. Additionally, fuel swelling, fission product distribution, cladding strain, fission gas release, fuel microstructure and fuel cladding chemical interaction were all evaluated. The fission gas release was 79.9% and the microstructure along the fuel pin presented several characteristics very similar to other EBR-II U-Pu-Zr ternary metallic fuel experience. Minor actinides seem to not dramatically affect the overall performance of this candidate transmutation fuel. Scanning Electron Microscopy was also performed and an in-depth characterization of the different regions and phases is presented. Performance data from these irradiations can be used to inform the feasibility of minor actinide transmutation in future reactor systems.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Validation of MFUEL Metal Fuel Performance Models of SAS4A/SASSYS-1

The fuel characterization models of SAS4A/SASSYS-1 (SAS) have recently been extended to include a new U-Pu-Zr metal fuel model, MFUEL. MFUEL is equipped with mechanistic physics based models to predict the pre-transient characterization and transient response of metal fuel, with emphasis on fuel melting, cladding failure, and the metal fuel’s impact on core reactivity. The MFUEL model will be available in the full version of SAS4A/SASSYS-1 5.7, which is scheduled to be released in June 2023. Fast reactor fuel pins that operated in EBR-II and FFTF with low smear density U-Zr and U-Pu-Zr metal fuels and irradiation resistant ferritic-martensitic cladding showed significant advantages in achieving high burnups and assuring inherent safety characteristics during anticipated transients, design basis events, and beyond design basis events. For safety analysis, a fuel performance model must be able to predict (1) Fuel pin mechanics and compositional and dimensional changes, (2) Clad failure, and (3) Fuel pin thermal resistance. Achieving these high level goals accurately is strongly related to the model performance of individual physical processes taking place within a fuel pin during its lifetime. Metal fuels typically operate above the mid-point temperature of melting during normal, as well as off-normal, conditions. At these elevated temperatures, the availability of thermal activation provides a driving force for various diffusional processes leading to complex phase transformations, micro-structure evolution, significant amounts of fuel swelling, interconnected porosity formation, excessive amounts of fission gas release, and fuel clad chemical interactions. Clad failure in fast reactors primarily occurs as a result of creep rupture augmented by clad wastage formation. The reaction is driven by thermal creep induced dislocation motion, grain boundary cavity nucleation, growth and breakup of grain boundaries. The high level complexity and limited available data requires introducing physics-based modeling approaches to gain extrapolation ability and sensitivity with respect to various conditions. The objective of this report is to perform validation of MFUEL using the experimental data for (1) Normal operation EBR-II fuel behavior, (2) Normal operation PHENIX fuel behavior, (3) HT9 Pressure tube ramp-and-hold creep rupture tests, (4) Whole Pin Furnace (WPF) creep strain, creep rupture and eutectic tests, (5) Fuel Behavior Test Apparatus (FBTA) eutectic tests, and (6) TREAT M5-7 OverPower tests up to clad failure. Section-2 includes a brief description of the MFUEL models. A detailed description of the MFUEL physics-based, semi-empirical models will be presented in the SAS V 5.7 theory manual. Section-3, 4, and 5 describes the validation effort for the pre-transient irradiation, furnace transients, and TREAT M-Series transients, respectively.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1973

Testing of uranium nitride fuel in T-111 cladding at 1200 K cladding temperature

Two groups of six fuel pins each were assembled, encapsulated, and irradiated in the Plum Brook Reactor. The fuel pins employed uranium mononitride (UN) in a tantalum alloy clad. The first group of fuel pins was irradiated for 1500 hours to a maximum burnup of 0.7-atom-percent uranium. The second group of fuel pins was irradiated for about 3000 hours to a maximum burnup of 1.0-atom-percent uranium. The average clad surface temperature during irradiation of both groups of fuel pins was approximately 1200 K. The postirradiation examination revealed the following: no clad failures or fuel swelling occurred; less than 1 percent of the fission gases escaped from the fuel; and the clad of the first group of fuel pins experienced clad embrittlement whereas the second group, which had modified assembly and fabrication procedures to minimize contamination, had a ductile clad after irradiation.

Rohal, R. G.↗
DOE OSTI2020

Postirradiation examination from separate effects irradiation testing of uranium nitride kernels and coated particles

An overview of postirradiation examination results for uranium nitride kernels and uranium nitride coated particles irradiated in the High Flux Isotope Reactor are presented. This is the first postirradiation examination of the MiniFuel irradiation vehicle that was recently developed to rapidly accumulate burnup during separate effects irradiation testing. In general, the burnup and fuel temperatures measured postirradiation were consistent with the design calculations. The burnup measured by mass spectrometry ranged from 5.9 to 10 MWd/kgU and was achieved after only 68 effective full-power days of irradiation. The dilatometric evaluation of passive silicon carbide thermometry indicated that the fuel was irradiated at temperatures ranging from 410 to 460 °C. Because the irradiation temperatures and burnup were low, the UN kernels showed minimal fission gas release that was within the range of the expected recoil (athermal) release. While it is possible to measure fuel swelling using x-ray computed tomography, the observed swelling was too small to quantify in this case. Extensive microstructural characterization of the irradiated fuel was performed in this study, and no significant irradiation induced changes were observed.

36 MATERIALS SCIENCE↗
NASA NTRS1973

EXFILE: A program for compiling irradiation data on UN and UC fuel pins

A FORTRAN-4 computer program for handling fuel pin data is described. Its main features include standardized output, easy access for data manipulation, and tabulation of important material property data. An additional feature allows simplified preparation of input decks for a fuel swelling computer code (CYGRO-2). Data from over 300 high temperature nitride and carbide based fuel pin irradiations are listed.

Mayer, J. T.↗
DOE OSTI2025

MURR LEU structural and thermal hydraulics analyses: Part I – Preliminary irradiation thermo-mechanical behavior

The University of Missouri Research Reactor (MURR) is expected to be converted from highly enriched uranium (HEU, ≥ 20 wt% U-235) U-Al x dispersion fuel to low-enriched uranium (LEU, < 20 wt% U-235) with U-10Mo monolithic fuel. This work introduces high-fidelity irradiation thermo–mechanical (T-M) analysis of the MURR LEU focusing on changes in coolant channel gap thickness. Three-dimensional (3D) finite element (FE) models were developed to simulate the irradiation T-M behavior of the MURR LEU element with all 23 curved fuel plates, the two side plates, and the combs. It was shown that channel gap thickness changes were influenced not only by plate thickness variations due to fuel swelling and creep but also by the radial displacement of consecutive MURR LEU plates. Modeling the fuel element assembly captured side plate displacements, which were shown to reduce radial fuel plate displacements towards the convex side. The maximum local radial displacement in the element was predicted at the end of life (EOL) as 23.7 mil (602.0 µm) on the lateral centerline of plate 23 towards the convex side. The maximum stripe-averaged reduction in channel gap thickness, particularly relevant for thermal hydraulics (TH) safety analysis, was calculated as 15.9 mil (403.9 µm) in single-side heated channel 24 (the outermost channel). These results account for the thermal resistance from the oxide build-up on cladding surfaces which was shown to be up to 0.82 mil (20.8 µm) thick. It was demonstrated that accounting for oxide layer thermal resistance led to a 10 °C higher peak fuel temperature and a 4.4 mil (111.8 µm) greater maximum local radial displacement. The impact of the calculated channel gap thickness changes on the MURR LEU TH safety analysis is evaluated in Part II.

Irradiation thermo-mechanical analysis↗
DOE OSTI2024

Grain boundary self-diffusion and point defect interactions in α -U via molecular dynamics

Though metallic U-Zr fuel has been used in nuclear reactors since the 1960s, many of its fundamental and thermodynamic properties are still unknown. The a-U phase, which has a highly anisotropic crystal structure and physical properties, is present in U-Zr fuel. The character and behavior of a-U grain boundaries will strongly impact fuel thermophysical performance under irradiation. Here, we study the interaction of point defects with grain boundaries, diffusion along grain boundaries, and the predicted diffusional creep behavior of a-U via molecular dynamics. We calculate the segregation energy of vacancies and interstitials to grain boundaries and quantify the biased sink strength of the grain boundaries, and observe that this sink strength is not strongly dependent on the grain boundary orientation. We also find that grain boundary diffusivity is strongly dependent on the grain boundary energy and grain boundary orientation. The presence of point defects within the grain boundary can induce diffusion in grain boundaries with low formation energies and can enhance diffusion in high-energy grain boundaries. We also find that diffusional creep of a-U at prototypical metallic fuel operation conditions is extremely high and could help explain observed metallic fuel swelling behaviors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

ROADRUNNER MiniFuel Experiment: Irradiation Target Design and Sample Characterization

High-density uranium nitride (UN) is a fuel candidate for several advanced nuclear reactor designs currently under development. Because there are limited UN performance data relative to fuel fabrication impurity and density variation, an irradiation campaign has been developed as part of a collaborative effort among the University of Texas at San Antonio (UTSA), Westinghouse Electric Company, Oak Ridge National Laboratory (ORNL), and Los Alamos National Laboratory (LANL) under the Nuclear Science User Facilities program. This project, entitled ROADRUNNER, or Research On ADvancing the peRformance of UraNium Nitrides in Extreme enviRonments, aimsto support UN fuel qualification for advanced reactors by investigating the impact of density and impurity variations on UN performance as a function of irradiation temperature and burnup. The MiniFuel experiment vehicle developed by ORNL, which leverages the High Flux Isotope Reactor, was selected to perform this accelerated separate-effects irradiation testing. The experiment test matrix consists of six MiniFuel targets containing miniature UN fuel disks, and targets three distinct burnup levels (37.5, 60, and 75 MWd/kg U) and three distinct temperatures (600, 900, and 1200°C). Neutronics and thermal analyses were performed to determine the experimental parameters needed to meet the desired irradiation conditions and to predict the experiment components temperatures. UN pellets were fabricated at LANL with tightly controlled parameters to produce specimens with three distinct densities and three levels of carbon content. The pellets were then thinned down by UTSA to the experiment-required thickness. The pre-characterization of the specimens includes density measurements, carbon and oxygen contents, microstructure analysis, and x-ray computed tomography. The selected specimens will be assembled into the MiniFuel experiment, and the first ROADRUNNER MiniFuel targets are intended for HFIR insertion during the Fall of 2024. After irradiation, the targets will be shipped to ORNL’s hot cell facility for disassembly. The post-irradiation examination on the fuel specimens includes fission gas release measurements, visual inspection, fuel swelling measurements, gamma spectroscopy, and microstructure analysis. The data collected post-irradiation will be used to develop fuel performance models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Transient fuel performance analysis for the preliminary fuel concept of general atomics fast modular reactor

This study investigates the transient fuel performance of General Atomics Fast Modular Reactor (GA-FMR) during accident scenarios, focusing on the behavior of its innovative fuel system that combines high-assay low enriched uranium dioxide (HALEUO2) fuel with SiGA® ceramic matrix composite silicon carbide cladding. The preliminary fuel design’s response was analyzed during reactivity-initiated accidents (RIA) and loss of coolant accidents (LOCA) using BISON fuel performance analysis code, which included both the diffusion enhanced and BISON-FASTGRASS coupled UO 2 models. The RIA analysis demonstrated that effective reactivity control reduced fuel temperature, though with transient fission gas release resulting in additional tensile stress state on the cladding. LOCA simulations revealed differing predictions between the two models: the BISON UO 2 model showed more transient fission gas release but minimal pellet expansion, while the BISON-FASTGRASS UO 2 model predicted less pronounced fission gas release but more fuel swelling and thermal expansion, potentially leading to pellet-cladding mechanical interaction. Here, these findings highlight critical areas for fuel design optimization and identify knowledge gaps requiring further experimental and computational investigation to advance GA-FMR fuel development.

Lee, Soon K. [Argonne National Laboratory (ANL), A↗
DOE OSTI2023

The role of UC inclusions in the development of fission gas bubble superlattice neutron-irradiated monolithic U-10Mo fuels

Uranium Carbide (UC) inclusions are the most prevalent impurities in Uranium-Molybdenum (U-Mo) fuel and are considered undesirable because they could potentially affect fuel performance. This work revealed that, like grain boundaries (gBs), UC inclusions could help facilitate the formation of the fission gas bubble superlattice (GBS). The GBS is a highly organized complex defect structure that can effectively store fission gases, thereby inhibiting fuel swelling. Transmission electron microscopy (TEM) showed that GBS self-organization can initiate at the UC/U-Mo interfaces in U-10Mo fuel irradiated to low fission density. Furthermore, this study also revealed that the UC boundary in U-10Mo irradiated to low fission density is wavy and periodic in morphology and that GBS formation is semi-coherent with the UC boundary. Because the initiation of GBS occurs at gBs and UC/U-Mo interfaces, the fission gas inventory is always highest at those regions compared to the U-Mo grain interior. Consequently, at higher fission densities, it is likely that high burnup structure (HBS) development via grain refinement will begin at gBs and UC/U-Mo interfaces.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Nuclear fuel irradiation testbed for nuclear security applications

The nuclear security community has long been interested in the identification and quantification of nuclear material signatures to understand a material’s provenance, use, and ultimate application. New forensics signatures and methods intended for non-traditional or advanced nuclear fuel applications require fuel irradiation experiments to demonstrate viability and validity. Integral fuel irradiations have historically required significant costs and long timelines to design, irradiate, and characterize. This paper describes how a recently developed nuclear fuel irradiation testbed can be used to provide a low cost, rapid turnaround, modular test environment for irradiation and evaluation of nuclear fuel specimens for nuclear security applications. The irradiation testbed houses six small ‘MiniFuel’ samples within hermetically sealed capsules inside targets that can be removed in between each ∼25-day operating cycle of the High Flux Isotope Reactor (HFIR). As many as nine targets can be irradiated using a single irradiation position (reflector region) in HFIR, allowing for varying irradiation temperatures and burnups. A suite of hot cell capabilities have been established to perform post-irradiation examination for measuring performance (e.g., fuel swelling, fission gas release) and facilitating experiment disassembly for subsequent property measurements, microstructural analysis, or chemical assay. This new testbed allows fuel irradiations to be conducted on an accelerated timeframe to enable rapid proof of concept testing and to provide reference material for nuclear fuel security applications. Recent applications using this testbed include the testing of isotopic taggants in UO 2 fuel (intentional forensics), testing of U-10Mo fuel for down-conversion of highly enriched uranium–fueled reactors, and the production of irradiated UO 2 fuel material for signature analysis of its isotopic composition (plutonium, fission gases, etc.).

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
NASA NTRS1973

Examination of T-111 clad uranium nitride fuel pins irradiated up to 13,000 hours at a clad temperature of 990 C

The examination of 27 fuel pins irradiated for up to 13,000 hours at 990 C is described. The fuel pin clad was a tantalum alloy with uranium nitride as the nuclear fuel. Two nominal fuel pin diameters were tested with a maximum burnup of 2.34 atom percent. Twenty-two fuel pins were tested for fission gas leaks; thirteen pins leaked. Clad ductility tests indicated clad embrittlement. The embrittlement is attributed to hydrogen from an n,p reaction in the fuel. Fuel swelling was burnup dependent, and the amount of fission gas release was low, generally less than 0.5 percent. No incompatibilities between fuel, liner, and clad were in evidence.

Slaby, J. G.↗