Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “formation kinetics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Utilizing TiO 2 amorphous precursors for polymorph selection: An in situ TEM study of phase formation and kinetics

Selective synthesis of metastable polymorphs requires a fundamental understanding of the complex energy landscapes in which these phases form. Recently, the development of in situ high temperature and controlled atmosphere transmission electron microscopy has enabled the direct observation of nucleation, growth, and phase transformations with near atomic resolution. In this work, we directly observe the crystallization behavior of amorphous TiO 2 thin films grown under different pulsed laser deposition conditions and quantify the mechanisms behind metastable crystalline polymorph stabilization. Films deposited at 10 mTorr chamber oxygen pressure crystallize into nanocrystalline Anatase at 325 degrees C, whereas films deposited at 2 mTorr crystallize into significantly larger needle-like grains of Brookite and Anatase at 270 degrees C. Increasing film deposition rate by a factor of 4 results in a 10x increase in the crystalline growth front velocity as well as a decrease in crystallization temperature from 270 degrees C to 225 degrees C. Engineering the amorphous precursor state through deposition conditions therefore provides routes to microstructure control and the accessibility of higher energy metastable phases.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Second Generation Readout For Large Format Photon Counting Microwave Kinetic Inductance Detectors

We present the development of a second generation digital readout system for photon counting microwave kinetic inductance detector (MKID) arrays operating in the optical and near-infrared wavelength bands. Our system retains much of the core signal processing architecture from the first generation system but with a significantly higher bandwidth, enabling the readout of kilopixel MKID arrays. Each set of readout boards is capable of reading out 1024 MKID pixels multiplexed over 2 GHz of bandwidth; two such units can be placed in parallel to read out a full 2048 pixel microwave feedline over a 4 GHz–8 GHz band. As in the first generation readout, our system is capable of identifying, analyzing, and recording photon detection events in real time with a time resolution of order a few microseconds. Here, we describe the hardware and firmware, and present an analysis of the noise properties of the system. We also present a novel algorithm for efficiently suppressing IQ mixer sidebands to below −30 dBc.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Accelerated Zymonic Acid Formation from Pyruvic Acid at the Interface of Aqueous Nanodroplets

To explore the role of the liquid interface in mediating reactivity in small compartments, the formation kinetics of zymonic acid (ZA) is measured in submicron aerosols (average radius = 240 nm) using mass spectrometry. The formation of ZA, from a condensation reaction of two pyruvic acid (PA) molecules, proceeds over days in bulk solutions, while in submicron aerosols, it occurs in minutes. The experimental results are replicated in a kinetic model using an apparent interfacial reaction rate coefficient of krxn = (0.9 ± 0.2) × 10-3 M-1 s-1. The simulation reveals that surface activity of PA coupled with an enhanced interfacial reaction rate drives accelerated ZA formation in aerosols. Experimental and simulated results provide compelling evidence that the condensation reaction of PA occurs exclusively at the aerosol interface with a reaction rate coefficient that is enhanced by 4 orders of magnitude (∼104) relative to what is estimated for macroscale solutions.

Kim, Pyeongeun↗
DOE OSTI2022

Global simulations of monoterpene-derived peroxy radical fates and the distributions of highly oxygenated organic molecules (HOMs) and accretion products

Abstract. We evaluate monoterpene-derived peroxy radical (MT-RO2) unimolecular autoxidation and self- and cross-reactions with other RO2 species in the GEOS-Chem global chemical transport model. The formation of associated highly oxygenated organic molecules (HOMs) and accretion products are tracked in competition with other bimolecular reactions. Autoxidation is the dominant fate up to 6–8 km for first-generation MT-RO2, which can undergo unimolecular H shifts. Reaction with NO can be a more common fate for H-shift rate constants < 0.1 s−1 or at altitudes higher than 8 km due to the imposed Arrhenius temperature dependence of unimolecular H shifts. For MT-derived HOM-RO2, generated by multistep autoxidation of first-generation MT-RO2, reaction with other RO2 species is predicted to be the major fate throughout most of the boreal and tropical forest regions, whereas reaction with NO dominates in the temperate and subtropical forests of the Northern Hemisphere. The newly added reactions result in an approximate 4 % global average decrease in HO2 and RO2, mainly due to faster self-/cross-reactions of MT-RO2, but the impact upon HO2, OH, and NOx abundances is only important in the planetary boundary layer (PBL) over portions of tropical forests. Predicted HOM concentrations in MT-rich regions and seasons can exceed total organic aerosol predicted by the standard version of the GEOS-Chem model depending on the parameters used. Comparisons to observations reveal that large uncertainties remain for key reaction parameters and processes, especially with respect to the photochemical lifetime and volatility of HOMs as well as the rates and branching of associated RO2 accretion products. Further observations and laboratory studies related to MT-RO2-derived HOMs and gas-phase RO2 accretion product formation kinetics – especially their atmospheric fate, such as gas–particle partitioning, multiphase chemistry, and net secondary organic aerosol formation – are needed.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Spatiotemporal Formation and Growth Kinetics of Polyelectrolyte Complex Micelles with Millisecond Resolution

We have directly observed the in situ self-assembly kinetics of polyelectrolyte complex (PEC) micelles by synchrotron time-resolved small-angle X-ray scattering, equipped with a stopped-flow device that provides millisecond temporal resolution. A synthesized neutral-charged diblock polycation and homopolyanion that we have previously investigated as a model charge-matched, core-shell micelle system were selected for this work. The initial micellization of the oppositely charged polyelectrolytes was completed within the dead time of mixing of 100 ms, followed by micelle growth and equilibration up to several seconds. By combining the structural evolution of the radius of gyration (R-g) with complementary molecular dynamics simulations, we show how the self-assemblies evolve incrementally in size over time through a two-step kinetic process: first, oppositely charged polyelectrolyte chains pair to form nascent aggregates that immediately assemble into spherical micelles, and second, these PEC micelles grow into larger micellar entities. Furthermore, this work has determined one possible kinetic pathway for the initial formation of PEC micelles, which provides useful physical insights for increasing fundamental understanding self-assembly dynamics, driven by polyelectrolyte complexation that occurs on ultrafast time scales.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Bioinspired stability enhancement in deuterium-substituted organic–inorganic hybrid perovskite solar cells

Abstract In hybrid perovskite solar cells (PSCs), the reaction of hydrogens (H) located in the amino group of the organic A-site cations with their neighboring halides plays a central role in degradation. Inspired by the retarded biological activities of cells in heavy water, we replaced the light H atom with its abundant, twice-as-heavy, nonradioactive isotope, deuterium (D) to hamper the motion of H. This D substitution retarded the formation kinetics of the detrimental H halides in Pb-based PSCs, as well as the H bond-mediated oxidation of Sn2+ in Sn–Pb-based narrow-bandgap PSCs, evidenced by accelerated stability studies. A computational study indicated that the zero point energy of D-based formamidinium (FA) is lower than that of pristine FA. In addition, the smaller increase in entropy in D-based FA than in pristine FA accounts for the increased formation free energy of the Sn2+ vacancies, which leads to the retarded oxidation kinetics of Sn2+. In this study, we show that substituting active H with D in organic cations is an effective way to enhance the stability of PSCs without sacrificing photovoltaic (PV) performance. This approach is also adaptable to other stabilizing methods.

14 SOLAR ENERGY↗
DOE OSTI2024

Importance of gas heating in capacitively coupled radiofrequency plasma-assisted synthesis of carbon nanomaterials

In pursuit of diamond nanoparticles, a capacitively-coupled radio frequency flow-through plasma reactor was operated with methane-argon gas mixtures. Signatures of the final product obtained microscopically and spectroscopically indicated that the product was an amorphous form of graphite. This result was consistent irrespective of combinations of the macroscopic reactor settings. To explain the observed synthesis output, measurements of C 2 and gas properties were carried out by laser-induced fluorescence and optical emission spectroscopy. Strikingly, the results indicated a strong gas temperature gradient of 100 K per mm from the center of the reactor to the wall. Based on additional plasma imaging, a model of hot constricted region (filamentation region) was then formulated. It illustrated that, while the hot constricted region was present, the bulk of the gas was not hot enough to facilitate diamond sp 3 formation: characterized by much lower reaction rates, when compared to sp 2 , sp 3 formation kinetics are expected to become exponentially slow. This result was further confirmed by experiments under identical conditions but with a H 2 /CH 4 mixture, where no output material was detected: if graphitic sp 2 formation was expected as the main output material from the methane feedstock, atomic hydrogen would then be expected to etch it away in situ, such that the net production of that sp 2 -hybridized solid material is nearly a zero. Finally, the crucial importance of gas heating was corroborated by replacing RF with microwave source whereby facile sp 3 production was attained with H 2 /CH 4 gas mixture.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Internally Catalyzed Hydrogen Atom Transfer (I-CHAT)—A New Class of Reactions in Combustion Chemistry

The current paradigm of low-T combustion and autoignition of hydrocarbons is based on the sequential two-step oxygenation of fuel radicals. The key chain-branching occurs when the second oxygenation adduct (OOQOOH) is isomerized releasing an OH radical and a key ketohydroperoxide (KHP) intermediate. The subsequent homolytic dissociation of relatively weak O–O bonds in KHP generates two more radicals in the oxidation chain leading to ignition. Based on the recently introduced intramolecular “catalytic hydrogen atom transfer” mechanism (J. Phys. Chem. 2024, 128, 2169), abbreviated here as I-CHAT, we have identified a novel unimolecular decomposition channel for KHPs to form their classical isomers—enol hydroperoxides (EHP). The uncertainty in the contribution of enols is typically due to the high computed barriers for conventional (“direct”) keto–enol tautomerization. Remarkably, the I-CHAT dramatically reduces such barriers. The novel mechanism can be regarded as an intramolecular version of the intermolecular relay transfer of H-atoms mediated by an external molecule following the general classification of such processes (Catal. Rev.-Sci. Eng. 2014, 56, 403). Here, we present a detailed mechanistic and kinetic analysis of the I-CHAT-facilitated pathways applied to n-hexane, n-heptane, and n-pentane models as prototype molecules for gasoline, diesel, and hybrid rocket fuels. We particularly examined the formation kinetics and subsequent dissociation of the γ-enol-hydroperoxide isomer of the most abundant pentane-derived isomer γ-C5-KHP observed experimentally. To gain molecular-level insight into the I-CHAT catalysis, we have also explored the role of the internal catalyst moieties using truncated models. All applied models demonstrated a significant reduction in the isomerization barriers, primarily due to the decreased ring strain in transition states. In addition, the longer-range and sequential H-migration processes were also identified and illustrated via a combined double keto–enol conversion of heptane-2,6-diketo-4-hydroperoxide as a potential chain-branching model. To assess the possible impact of the I-CHAT channels on global fuel combustion characteristics, we performed a detailed kinetic analysis of the isomerization and decomposition of γ-C5-KHP comparing I-CHAT with key alternative reactions—direct dissociation and Korcek channels. Calculated rate parameters were implemented into a modified version of the n-pentane kinetic model developed earlier using RMG automated model generation tools (ACS Omega, 2023, 8, 4908). Simulations of ignition delay times revealed the significant effect of the new pathways, suggesting an important role of the I-CHAT pathways in the low-T combustion of large alkanes.

Biochemistry & Molecular Biology↗
DOE OSTI2023

Modulating the Mixing Gibbs Free Energy to Enhance Solid–Liquid Phase Separation for High–Performance Organic Solar Cells

Organic solar cells (OSC) feature a hierarchical structure with the electron donor/acceptor layer sandwiched by anode and cathode, which raises the importance of controlling the molecular crystal orientation, domain size, and vertical distribution to facilitate the charge collection at electrodes. However, the similar conjugated backbone of donor/acceptor material and fast film–formation kinetics have led to spinodal–decomposition–orientated phase separation that result in the film presenting an intimately mixed morphology and random molecular orientation. To solve the issue, the mixing Gibbs free energy–triggered solid–liquid phase separation during the film formation process is enhanced by solidifying one component and solvating the other based on a liquid additive. Following the liquid evaporation process, a favorable vertical distribution is obtained. Meanwhile, the prolonged solvation process enlarges the domain size and assists the molecules to diffuse and orient properly, enabling better exciton/charge dynamics during the power conversion processes. As a result, the fabricated devices exhibit a fill factor over 80% and an efficiency of 18.72%, which is one of the top efficiencies for binary OSCs. In conclusion, insights and a methodology is provided here to manipulate the organic donor/acceptor phase separation in terms of mixing Gibbs free energy.

14 SOLAR ENERGY↗
DOE OSTI2022

Kinetic processes of phase separation and aggregation behaviors in slot-die processed high efficiency Y6-based organic solar cells

Morphological optimization has proved to be one crucial factor contributing to the 19% efficiency of Y6-based organic solar cells (OSCs). Although the relationship between component miscibility and film morphology has been established, it has not been clarified how the film formation processes proceed, especially for methods compatible with large-area fabrication, i.e. slot-die coating, which restricts the further optimization of the morphology. Herein, we comprehensively investigate the effect of miscibility and the film-formation kinetic process on film morphology during processing with different solvents. A highest power conversion efficiency (PCE) of 17.38% can be obtained in a D18:Y6 device processed with slot-die coating in an open-air environment. However, due to their relatively poor miscibility, incorporating a trace amount of chlorobenzene (CB) into CF can sufficiently promote Y6 aggregation, leading to increased phase separation and thus the average PCE drops to 15.16%. In contrast, a PM6:Y6 blend shows insensitive changes in the kinetic process as well as the final morphology, and thus in the comparable PCEs when cast with different solvents, which is ascribed to their relatively good miscibility. As a result, this work provides scientific guidelines for device optimization by combining the intermediate gap from miscibility to kinetic process and their impact on final morphology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Irreversible Catalyst Deactivation Mechanisms of PdO/γ-Al 2 O 3 Catalysts for Lean Methane Oxidation

PdO/γ-Al 2 O 3 catalysts suffer from gradual and irreversible catalyst deactivation under lean CH 4 oxidation conditions, especially in a wet feed. Here, time-resolved CO chemisorption DRIFTS measurements are conducted systematically on a series of PdO/γ-Al 2 O 3 catalysts to probe the surface reactivity of PdO nanoparticles after various in situ pretreatments. At 80 °C, CO barely adsorbs on fully oxidized PdO surfaces but interacts with coordinatively unsaturated Pd sites, causing gradual reduction of the PdO surfaces. This results in the formation of characteristic IR bands on various metallic Pd 0 sites. By monitoring and comparing the formation kinetics of these IR bands on samples before and after CH 4 oxidation, we theorize that the irreversible catalyst deactivation during CH 4 oxidation is caused by PdO surface reconstruction, in which coordinatively unsaturated Pd sites gradually become fully coordinated by oxygen. Effectively, the surface reconstruction leads to the formation of a passivation layer on the PdO nanoparticles, which hinders their ability in activating CH 4 , and hence the subsequent oxidation reaction. Temperature-programmed reduction with CO as the reductant (CO-TPR) reveals that the passivation layer formed during CH 4 oxidation is significant enough to increase the reduction temperature of PdO nanoparticles of the 3.0% PdO/γ-Al 2 O 3 samples, although such an effect is less obvious for the 0.4% PdO/γ-Al 2 O 3 samples. On the other hand, it is also discovered that the passivation layer is not completely inert. Under certain reaction conditions, with some being relatively mild, such as low-temperature CO oxidation in a net lean atmosphere and in the presence of H 2 O, the passivation layer can undergo structure change which results in regeneration or even activation of CH 4 oxidation activity of an already deactivated catalyst. Additionally, it is discovered that the fully coordinated Pd–O surface is a metastable phase under CH 4 oxidation conditions. In the presence of H 2 O and at ambient temperatures, surfaces with coordinatively unsaturated Pd sites are thermodynamically more favorable.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

High-throughput phase-field simulations and machine learning of resistive switching in resistive random-access memory

Metal oxide-based Resistive Random-Access Memory (RRAM) exhibits multiple resistance states, arising from the activation/deactivation of a conductive filament (CF) inside a switching layer. Understanding CF formation kinetics is critical to achieving optimal functionality of RRAM. Here a phase-field model is developed, based on materials properties determined by ab initio calculations, to investigate the role of electrical bias, heat transport and defect-induced Vegard strain in the resistive switching behavior, using MO 2- x systems such as HfO 2- x as a prototypical model system. It successfully captures the CF formation and resultant bipolar resistive switching characteristics. High-throughput simulations are performed for RRAMs with different material parameters to establish a dataset, based on which a compressed-sensing machine learning is conducted to derive interpretable analytical models for device performance (current on/off ratio and switching time) metrics in terms of key material parameters (electrical and thermal conductivities, Vegard strain coefficients). These analytical models reveal that optimal performance (i.e., high current on/off ratio and low switching time) can be achieved in materials with a low Lorenz number, a fundamental material constant. This work provides a fundamental understanding to the resistive switching in RRAM and demonstrates a computational data-driven methodology of materials selection for improved RRAM performance, which can also be applied to other electro-thermo-mechanical systems.

36 MATERIALS SCIENCE↗
DOE OSTI2021

CsPbI 3 Nanocrystals Go with the Flow: From Formation Mechanism to Continuous Nanomanufacturing

Despite the groundbreaking advancements in the synthesis of inorganic lead halide perovskite (LHP) nanocrystals (NCs), stimulated from their intriguing size-, composition-, and morphology-dependent optical and optoelectronic properties, their formation mechanism through the hot-injection (HI) synthetic route is not well-understood. Here in this work, for the first time, in-flow HI synthesis of cesium lead iodide (CsPbI 3 ) NCs is introduced and a comprehensive understanding of the interdependent competing reaction parameters controlling the NC morphology (nanocube vs nanoplatelet) and properties is provided. Utilizing the developed flow synthesis strategy, a change in the CsPbI 3 NC formation mechanism at temperatures higher than 150 °C, resulting in different CsPbI 3 morphologies is revealed. Through comparison of the flow- versus flask-based synthesis, deficiencies of batch reactors in reproducible and scalable synthesis of CsPbI 3 NCs with fast formation kinetics are demonstrated. The developed modular flow chemistry route provides a new frontier for high-temperature studies of solution-processed LHP NCs and enables their consistent and reliable continuous nanomanufacturing for next-generation energy technologies.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High‐Performance Green Thick‐Film Ternary Organic Solar Cells Enabled by Crystallinity Regulation

Abstract The power conversion efficiency (PCE) of organic solar cells (OSCs) has reached high values of over 19%. However, most of the high‐efficiency OSCs are fabricated by spin‐coating with toxic solvents and the optimal photoactive layer thickness is limited to 100 nm, limiting practical development of OSCs. It is a great challenge to obtain ideal morphology for high‐efficiency thick‐film OSCs when using non‐halogenated solvents due to the unfavorable film formation kinetics. Herein, high‐efficiency ternary thick‐film (300 nm) OSCs with PCE of 15.4% based on PM6:BTR‐Cl:CH1007 are fabricated by hot slot‐die coating using non‐halogenated solvent (o‐xylene) in the air. Compared to PM6:BTR‐Cl:Y6 blends, the stronger pre‐aggregation of CH1007 in solution induces the earlier aggregation of CH1007 molecules and longer aggregation time, and thus results in high and balanced crystallinity of donors and acceptor in CH1007‐based ternary film, which led to high‐carrier mobility and suppressed charge recombination. The ternary strategy is further used to fabricate high‐efficiency, thick‐film, large‐area, and flexible devices processed from non‐halogenated solvents, paving the way for industrial development of OSCs.

Chemistry↗
DOE OSTI2022

Narrowing the Phase Distribution of Quasi-2D Perovskites for Stable Deep-Blue Electroluminescence

Solution-processed quasi-2D perovskites contain multiple quantum wells with a broad width distribution. Inhomogeneity results in the charge funneling into the smallest bandgap components, which hinders deep-blue emission and accelerates Auger recombination. Here, a synthetic strategy applied to a range of quasi-2D perovskite systems is reported, that significantly narrows the quantum well dispersity. It is shown that the phase distribution in the perovskite film is significantly narrowed with controlled, simultaneous evaporation of solvent and antisolvent. Modulation of film formation kinetics of quasi-2D perovskite enables stable deep-blue electroluminescence with a peak emission wavelength of 466 nm and a narrow linewidth of 14 nm. Light emitting diodes using the perovskite film show a maximum luminance of 280 cd m –2 at an external quantum efficiency of 0.1%. This synthetic approach will serve in producing new materials widening the color gamut of next-generation displays.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Te(IV) immobilization by siderite: Reaction kinetics, mechanism, and Te isotopic fractionation

Mining and industrial use over recent decades have released tellurium (Te) into the environment where it potentially contaminates soils, water supplies and food sources. Therefore, it is important to find ways of removing mobile and bioavailable Te from aqueous environments. Here, we report aqueous Te(IV) removal by siderite at varying Te concentrations (2, 6 and 10 mg mL –1 Te(IV)) and pH values (7, 7.9 and 9), together with associated isotope fractionation (ε 130 Te/ 125 Te). Our results show effective immobilization of Te(IV) that follows pseudo-first order rate kinetics. Formation of magnetite indicates reduction of Te(IV) on siderite surfaces and the formation of Te(0). The overall isotope fractionation (ε) is small (–0.23 ± 0.06‰) providing evidence that it is primarily controlled by adsorption of Te(IV) occurring simultaneously with reduction of Te(IV). Therefore, Te(IV) removal by siderite under mildly reducing ferruginous conditions may be identifiable by the characteristically small isotopic fractionation during both natural attenuation and active remediation. To our knowledge, this is the first study reporting reaction mechanisms of Te(IV) immobilization by an environmentally relevant Fe(II) mineral.

58 GEOSCIENCES↗
DOE OSTI2022

Dynamic stability of a crude oil/brine interface: Effect of anion type

The chemical composition of the aqueous phase plays an essential role in water-based enhanced-oil recovery processes. The aqueous phase ionic profile affects the snap-off response of a crude oil-brine system by linking it to the brine-crude oil interfacial rheology. In this work, we focus on the effect of the anion on the snap-off response. To this end, a sample of crude oil from the Minnelusa Sandstone formation in Wyoming was selected, and several aqueous solutions were prepared with salts containing sodium cation and different anions (chlorides, sulfates, and phosphates) at two ionic strength values, 0.6 M and 6 mM, as cases of high- and low-salinity water. Interfacial tension, interfacial viscoelasticity and interface stability were analyzed as functions of aging time using pendant drop, dilatational rheology, and liquid bridge techniques, respectively. Here the results show that solutions with higher ionic strength led to the formation of more rigid interfaces, i.e. higher elastic modulus, and faster formation kinetics. In the low-salinity regime, solutions with polyvalent anions produce more viscoelastic interfaces at faster rates than solutions with monovalent anions. Finally, an excellent correlation (R 2 greater than 0.97) between the relative stability of the interfacial film, predicted in liquid bridge tests, and the ratio of interfacial tension and interfacial elastic modulus was found.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

The effect on soot and its gas precursors of doping ethylene with 2,2,4,6,6-pentamethyl-heptane in the nitrogen-fuel stream of a laminar non-premixed Planar Mixing Layer Flame (PMLF)

Synthetic Aviation Turbine Fuels (SATFs) are promising for reducing soot emissions from the aviation sector and diversifying Jet Fuel (JF) sources. Accurately predicting the combustion and emissions behavior of SATFs (and other JFs) necessitates robust experimental databases to elucidate the chemistry of long-chain iso-paraffins, which can compose up to two-thirds of SATF blends and whose behavior is considered to be well-represented by that of iso-dodecane isomers. Here, this study characterizes two laminar non-premixed Planar Mixing Layer Flames (PMLFs) with mild soot loads fueled by nitrogen-diluted ethylene, pure and doped with 2,2,4,6,6-pentamethyl-heptane, respectively. The two PMLFs have the same stoichiometric mixture fraction and total hydrocarbon mole fraction in the fuel stream (X F,F =X C2H4,F +X C12H26,F = 0.260), resulting in nearly the same maximum temperature (T max ≈1800 K) and simple identification of the effects of doping. Importantly, any horizontal PMLF cross-section has a self-similar structure that can be modeled as an equivalent One-Dimensional Counterflow Flame (1D-CF) with vanishingly small strain rate (a). The cross-section at a Height Above the Burner (HAB) of 50 mm is characterized in terms of C 0 -C 18 gas species using capillary sampling followed by GC-MS analyses. Laser-Induced Emission Spectroscopy (LIES) quantifies the soot volume fraction (ƒ v ) profiles at HAB=25 and 50 mm where Elastic Laser Light Scattering (E-LLS) is performed to determine the a of the equivalent 1D-CFs and the profile of the E-LLS equivalent diameter ( d 6,3 ) of soot. The substitution of 1500 ppm of ethylene with 2,2,4,6,6-pentamethyl-heptane causes an increase of ≈1.5 in the concentrations of several polycyclic aromatic hydrocarbons and fv. Concurrently, the measured d 6,3 doubles in the oxidizer stream, yet remains the same in the fuel stream, at HAB=50 mm. Instead, at HAB= 25 mm, the iso-dodecane doping does not affect the d 6,3 profile in either stream. The experimental results partially validate the chemical reactions and soot formation kinetic model developed at Lawrence Livermore National Laboratory and provide directions to further improve its predictions.

Iso-dodecane (2,2,4,6,6-Pentamethyl-Heptane)↗