Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flow instability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

FY24 Report on Water NSTF Testing: Lower Tank Inlet Piping Configuration

The following report serves as a summary of the accomplishments and testing results by the Natural convection Shutdown heat removal Test Facility (NSTF) experimental program over the past 12-month period. A major activity included reconfiguration of the chimney piping geometry which altered the discharge position into the tank from the original 50% tank height to a new lower position at a 10.9% tank height. This modification increases the volume of available coolant thus extending long-term operating capacity, however also results in a decreased liquid driving head which has the potential to reduce the natural circulation efficiency and decrease overall performance. Examination of the tradeoffs for these two configurations is an area of interest for RCCS designers and drove planned test activities this year. Ten matrix tests were performed in FY24, totaling 195 hours of heated operations and 12.9 MWh of electrical heating throughout the year, with eight classified as Accepted per NQA-1 and two classified as Trending. Testing prior to the facility reconfiguration examined the facility response to throttling at the tank inlet, demonstrating increased sensitivity of flow instabilities to throttling within the two-phase region when compared to throttling at the lower sensitivity single-phase inlet region. Testing after the chimney reconfiguration began with a baseline test at conditions of 80% inventory fill and prototypic thermal power input of 2.1 MW t . In addition to establishing a reference for nominal system behavior and performance, repeat testing with multiple subsequent runs demonstrated strong repeatability between tests performed at the same conditions in this new configuration. These tests also examined if influences would occur to system behavior with installation of new higher-resolution instrumentation within the upper chimney. In this critical region where boiling and flashing phenomena dominate, the test results provided confidence that the new instrumentation does not uncharacteristically influence the observed behaviors. An inventory parametric series was then initiated to examine system behavior with the new chimney configuration at six varying initial inventory levels, ranging from high 80% to low 20% fill. Two-phase oscillations with similar peak and mean flow rates were observed when comparing to the previous mid tank configuration. Generally, similar system response trends with inventory were also observed, such as two phase oscillations suppressing as inventories were lowered. However, in one absolute inventory comparison at the highest fill of 80%, flow oscillations saw a gradual growth over the 4 hours of two-phase operation in the new lower tank inlet configuration, opposite of the gradual dampening observed in the mid tank inlet configuration. This can be attributed to, in part, a greater hydrostatic head pressure above the two-phase discharge region where the boiling front is developed. Furthermore, the change resulted in greater sensitivity to liquid degassing phenomena during single-phase heating, causing loop instabilities to form which trigged moderate flow degradation during the period approaching saturation and boiling conditions. This behavior had been observed previously under some conditions but was a common occurrence in recent testing with the newer lower tank inlet configuration. Initial observations from these first data sets suggest an overall larger window of stability for the mid tank inlet configuration compared to the lower tank inlet. Lastly, the lowest inventory fill test was repeated over an extended testing window to examine depletion behavior. Natural circulation flow and effective heat removal performance were observed during most of the testing period; only after the tank became fully drained (0% fill) did flow stagnate and violent geysering events occur. This early observation confirms one relative advantage over the mid tank inlet configuration, which stagnated under comparable conditions at ~20% inventory remaining in the tank.

42 ENGINEERING↗
DOE OSTI2025

Modeling the effects of active wake mixing on wake behavior through large-scale coherent structures

The use of active wake mixing (AWM) to mitigate downstream turbine wakes has created new opportunities for reducing power losses in wind farms. However, many current analytical or semi-empirical wake models do not capture the flow instabilities that are excited through the blade pitch actuation. In this work, we develop a framework, which accounts for the impacts of the large-scale coherent structures and turbulence on the mean flow, for modeling AWM. The framework uses a triple-decomposition approach for the unsteady flow field and models the mean flow and fine-scale turbulence with a parabolized Reynolds-averaged Navier–Stokes (RANS) system. The wave components are modeled using a simplified spatial linear stability formulation that captures the growth and evolution of the coherent structures. Comparisons with high-fidelity large eddy simulations (LESs) of the turbine wakes showed that this framework was able to capture the additional wake mixing and faster wake recovery in the far-wake regions for both the pulse and helix AWM strategies with minimal computational expense. In the near-wake region, some differences are observed in both the RANS velocity profiles and initial growth of the large-scale structures, which may be due to some simplifying assumptions used in the model.

17 WIND ENERGY↗
DOE OSTI2023

A User’s Guide to the PLTEMP/ANL Code

PLTEMP/ANL V4.4 is a program that obtains a steady-state flow and temperature solution, in geometrical extent, for a nuclear reactor core, or a single fuel assembly, including the effect of manufacturing and modelling uncertainties by the means of hot channel factors. It is based on an evolutionary sequence of codes originally used for calculating plate temperatures, hence “PLTEMP”, developed at Argonne National Laboratory over the past 30 years. Fueled and non-fueled regions are modeled. Each fuel assembly consists of one or more plates or tubes separated by coolant channels. The fuel plates may have one to five layers of different materials, each with heat generation. The width of a fuel plate may be divided into multiple longitudinal stripes, each with its own axial power shape. Depending upon the heat transfer method selected, the temperature solution is effectively 2-dimensional or 3-dimensional. The geometry may be either slab or radial, corresponding to fuel assemblies made of a series of flat (or slightly curved) plates, or of nested tubes. A variety of thermal-hydraulic correlations are available to determine safety margins such as onset of nucleate boiling ratio (ONBR), departure from nucleate boiling ratio (DNBR), and onset of flow instability ratio (OFIR). Coolant properties for either light or heavy water are obtained from FORTRAN functions rather than from tables. The code is intended for thermal-hydraulic analysis of research reactor performance in the sub-cooled boiling regime. Both turbulent and laminar flow regimes can be modeled. Options to calculate both forced flow and natural circulation are available. A general search capability for select design and safety parameters is available to greatly reduce the reactor analyst’s time.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Impact of U-10Mo HALEU fuel element tolerances on the Massachusetts Institute of Technology reactor safety and operational performance – Thermal hydraulics

The U.S. is coordinating efforts for the conversion of six U.S. High Performance Research Reactors (USHPRR) including one critical facility from highly enriched uranium (HEU) to low-enriched uranium (LEU). In order to continue the mission of these reactors, including the Massachusetts of Institute of Technology Reactor (MITR), and achieve similar performance, high-assay low-enriched uranium (HALEU) with a high-density metallic alloy of uranium with 10 wt% molybdenum (U-10Mo) is being evaluated. The impact of the fabrication specification and tolerances was assessed following the preliminary design of the MITR LEU fuel elements using the U-10Mo monolithic alloy. This research focuses on the analysis of fabrication specification impact on thermal hydraulics (TH) characteristic of the MITR LEU core as a function of the variation of the relevant fuel specification parameters (e.g., coolant channel gap thickness, fuel plate thickness, etc.). The analyses are performed based on an all-fresh LEU fuel conversion plan identified in a preliminary safety analysis report submitted to the Nuclear Regulatory Commission. The reactor power margin to the onset of nucleate boiling (ONB) is assessed under the limiting safety system settings (LSSS), where a scram occurs, to ensure there is sufficient margin to the reactor safety limit, which is defined by the onset of flow instability that occurs after the ONB. The best estimate plus uncertainty approach is employed to analyze this TH characteristic, which yields realistic results while maintaining adequate conservatism, utilizing a statistical uncertainty propagation method with the STAT7 code. The TH characteristic is analyzed as a function of the variability of the specification parameters resulting from the fabrication process. The main findings of this study show that the MITR core can meet the TH safety and operational requirements at the all-LEU initial core startup (cycle 1), selected transition cycles (most reactive cycle and most limiting cycle: cycle 3 and 5, respectively) and equilibrium (cycle 14) cores under all limiting fabrication parameter combinations considered. In addition, the analyses show that the dependency of the core power margin to ONB on those specification parameters that have the most direct impact on TH performance is non-linear but monotonically decreasing within the specification tolerances. The third order polynomial fit curves are reported in detail for selected limiting cases and can serve as a powerful tool for future MITR fuel management in cases such as when HALEU supply is established that may allow additional cycle length or other operational benefits.

Conversion↗
DOE OSTI2025

Stemflow Hydrodynamics

Stemflow hydrodynamics is the study of water movement along the exterior surface area of plants. Its primary goal is to describe water velocity and water depth along the stem surface area. Its significance in enriching the rhizosphere with water and nutrients is not in dispute. Yet, the hydrodynamics of stemflow have been entirely overlooked. This review seeks to fill this knowledge gap by drawing from thin film theories to seek outcomes at the tree scale. The depth‐averaged conservation equations of water and solute mass are derived at a point. These equations are then supplemented with the conservation of momentum that is required to describe water velocities or relations between water velocities and water depth. Relevant forces pertinent to momentum conservation are covered and include body forces (gravitational effects), surface forces (wall friction), line forces (surface tension), and inertial effects. The inclusion of surface tension opens new vistas into the richness and complexity of stemflow hydrodynamics. Flow instabilities such as fingering, pinching of water columns into droplets, accumulation of water within fissures due to surface tension and their sudden release are prime examples that link observed spatial patterns of stemflow fronts and morphological characteristics of the bark. Aggregating these effects at the tree‐ and storm‐ scales are featured using published experiments. The review discusses outstanding challenges pertaining to stemflow hydrodynamics, the use of dynamic similarity and 3D printing to enable the interplay between field studies and controlled laboratory experiments.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Drag reduction and the Vogel exponent of a flexible beam in transient shear flows

Interactions between a flexible beam and a fluid in a channel are of great relevance to biological hairy surfaces, aquatic vegetation, marine life (e.g., fish gills), and many industrial systems alike. While steady state response of a beam to such flows is fairly well-explored, their behavior in the transient regime is not fully understood. Here, a series of numerical simulations are performed to study the laminar Couette flow of an incompressible viscous fluid past an elastic beam in a two-dimensional channel. The flexible beam is perpendicular to the direction of flow, and its base is fixed to the stationary bottom of the channel. We measure the evolution of the Vogel exponent, drag reduction, and reconfiguration number during the transient and steady-state response of the fluid–structure system for different geometrical and physical properties. Our benchmark shows a good agreement between numerical and experimental observations. Our results show that the system's steady-state response at different bulk-fluid velocities can be reproduced by investigating the shear flow response during the transient regime. We define a new variable that characterizes the evolution of the local velocity profile in the proximity of the free end of the beam and use that to characterize the transient-regime response. The analysis yields insight into the competing effects of elasticity of the beam and non-linear flow response.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Flow visualization in high-energy-density laboratory plasmas

Flow visualization is often essential for evaluating high-energy-density (HED) laboratory plasmas, examining their dynamics, and assessing design strategies. However, imaging at fine phenomenological flow scales is a major challenge. Here, a zone-plate–based radiography system tailored for applications in HED physics is demonstrated. The burst-mode radiography system combines a dual-flash laser-generated x-ray source, a high-magnification zone plate optic, and a multiple frame hybrid complementary metal-oxide-semiconductor (hCMOS) sensor for image detection. Operating at a magnification of 42 x⁠, a pair of radiographs is measured in rapid succession, each time gated by a 4.75 keV flash of x rays lasting 100 ps. The system achieves a spatial resolution below 3 μm. The potential of this approach for applications in HED physics is exemplified by observing small-scale spike morphologies at a pusher-foam interface impacted by a strong, laser-driven blast wave.

Flow instabilities↗
DOE OSTI2023

Mass and momentum transport in the Tilted Rocket Rig experiment

Here, high-fidelity large eddy simulations of the inclined Rayleigh-Taylor instability in the Tilted Rocket Rig experimental configuration [Smeeton and Youngs, AWE Report No. O 35/87 (1987)] are performed using a tenth-order compact finite difference code. These simulations are analyzed for spatial distributions of turbulent kinetic energy, turbulent mass flux velocity, species mass fraction flux, species mass fraction variance, and Favre-averaged Reynolds stresses at two time instances, t = 37 ms and t = 52 ms. Additionally, the vertical distribution of the components of the unclosed budget equations over the center of the domain for these quantities are examined. The dominant terms of these budget equations are further decomposed to examine the principal contributions to these terms in each axis. Notably, the principal contribution to the horizontal turbulent mass flux velocity budget is found to be from a term which is commonly neglected in many Reynolds-averaged Navier-Stokes models.

42 ENGINEERING↗
DOE OSTI2023

Verification and Validation of the PLTEMP/ANL Code for Thermal-Hydraulic Analysis of Experimental and Test Reactors, Volume 1

This is Volume 1 of a two-volume document that collects the verification and validation (V&V) works done for the PLTEMP/ANL code during the years of its development and improvement. Volume 1 describes the V&V of sixteen capabilities of the PLTEMP/ANL code that were identified by research reactor analysts as frequently used in their thermal-hydraulic analysis. Volume 2 describes the V&V of developments and improvements since the release of PLTEMP/ANL Version 4.3. Each chapter of the document focuses on verifying or validating a specific part of the software that calculates a specific phenomenon, e.g., channel flow calculation, coolant property calculation, heat transfer calculation, and flow instability calculation. Software verification is performed by comparing the code with hand calculation, Microsoft spreadsheet calculation, Mathematica calculation, or MATLAB calculation. The software validation is done by comparing the code with experimental data or a widely tested code like the RELAP5 code. In addition, some PLTEMP/ANL V&V works that are available in the open literature are simply cited in Volume 1 of the document. PLTEMP/ANL has been used in the safety analysis reports of several US and foreign research reactors licensed and converted from highly enriched uranium fuel to low-enriched uranium fuel. A list of such reactors is given in Volume 1 of the document.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Verification and Validation of the PLTEMP/ANL Code for Thermal-Hydraulic Analysis of Experimental and Test Reactors, Volume 2

This is Volume 2 of a two-volume document that collects the verification and validation (V&V) works done for the PLTEMP/ANL code during the years of its development and improvement. Volume 1 describes the V&V of sixteen capabilities of the PLTEMP/ANL code that were identified by research reactor analysts as frequently used in their thermal-hydraulic analysis. Volume 2 describes the V&V of developments and improvements since the release of PLTEMP/ANL Version 4.3. Each chapter of the document focuses on verifying or validating a specific part of the software that calculates a particular phenomenon, e.g., channel flow calculation, coolant property calculation, heat transfer calculation, and flow instability calculation. Software verification is performed by comparing the code with a hand calculation, Microsoft spreadsheet calculation, Mathematica calculation, or MATLAB calculation. The software validation is achieved by comparing the code with experimental data or a widely tested code like the RELAP5 code. In addition, some PLTEMP/ANL V&V works that are available in the open literature are simply referenced in Volume 1 of the document. PLTEMP/ANL has been used in safety analysis reports of several US and foreign research reactors licensed and converted from highly enriched uranium fuel to low-enriched uranium fuel. A list of such reactors is given in Volume 1 of the document.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Saturation of fishbone instability through zonal flows driven by energetic particle transport in tokamak plasmas

Gyrokinetic and kinetic-MHD simulations are performed for the fishbone instability in the DIII-D discharge #178631, chosen for validation of first-principles simulations to predict the energetic particle (EP) transport in an ITER prefusion baseline scenario. Fishbone modes are found to generate zonal flows, which dominate the fishbone saturation. The underlying mechanisms of the two-way fishbone-zonal flows nonlinear interplay are discussed in details. Numerical and analytical analyses identify the fishbone-induced EP redistribution as the dominant generation mechanism for zonal flows. The zonal flows modify the nonlinear dynamics of phase space zonal structures, which reduces the amount of EPs able to resonate with the mode, leading to an early fishbone saturation. Simulation results including zonal flows agree quantitatively with DIII-D experimental measurements of the fishbone saturation amplitude and EP transport, supporting this novel saturation mechanism by self- generated zonal flows. Moreover, the wave-particle mode-locking mechanism is shown to determine quantitatively the fishbone frequency down-chirping, as evident in GTC simulation results in agreement with predictions from analytical theory. Finally, the
fishbone-induced zonal flows are possibly responsible for the formation of an ion-ITB in the DIII-D discharge. Based on the low EP transport and the large zonal flow shearing rates associated with the fishbone instability in gyrokinetic simulations of the ITER scenario, it is conjectured that high performance scenarios could be designed in ITER burning plasmas through fishbone-induced ITBs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Theory of the magnetothermal instability in coronal plasma flows

The theory of the magnetothermal instability (MTI) is revisited through the lens of the stability of uniform systems. The linear stability analysis includes flow advection and Nernst transport. The instability criteria derived distinguish between the convective and the absolute nature of the perturbation growth. It is proven that, in the region where the Nernst and plasma blowoff velocities cancel, the MTI can be absolute and wave-packet perturbations grow in situ. This instability is mediated by the internal feedback between the Biermann battery and Righi–Leduc terms. Here, the analysis is extended to derive the dispersion relation for short-wavelength perturbations developing in nonuniform profiles with the application to coronal plasmas. It is found that the condition for MTI requires the net B-field convection velocity to be small at the isothermal sonic section, and the plasma conditions in this section govern the dynamics of the instability. Analysis of hydro-equivalent implosions suggests that unstable perturbations undergo more e-foldings of growth in larger-size targets.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Soft interface instability and gas flow channeling in low-permeability deformable media

Understanding gas percolation through a clay layer or a shale formation is of great importance for the development of a geologic repository for nuclear waste disposal, a subsurface system for gas storage, and an engineering approach for hydrocarbon extraction from unconventional reservoirs. Gas injection experiments have revealed complex dynamic behaviours of gas percolation through water saturated compacted bentonite, characterized by a high breakthrough pressure, rapid breakthrough, a pressure/stress decay after the breakthrough, a relatively high migration rate, high-frequency periodic/nonperiodic variations in flow rate, stepwise rate reductions during relaxation, and low gas saturation over the whole process, all indicating channelling nature of the processes. Using linear stability analyses, we show that this channelling can autonomously emerge from the instability of the deformable interface between the injected gas and the compacted bentonite matrix driven by local stress concentration, pore dilation, and hydrologic gradient. Channel patterns formed would possess a fractal geometry. We further show that, once a percolating channel is established, the gas injected would percolate through the channel in a chain of gas bubbles, also due to the interface instability, resulting in periodic/chaotic variations in gas flow rate. Our work provides a unified explanation for key features observed for gas percolation in low-permeability deformable media. The work also suggests a possibility of designing an engineered barrier system for a nuclear waste repository that can have controllable gas release while limit water transport.

Bentonite↗
DOE OSTI2022

Dispersion relation and instability for an anisotropic nonuniform flowing plasma

A generalized formula for wave instability is developed for an anisotropic nonuniform plasma with finite flows and temperatures. Six-moment fluid equations are solved to give the analytic expression for wave instability in arbitrarily nonuniform plasmas. The analytic formula explicitly states the dependence of wave instability on the nonuniformities of number density, flow velocity, and anisotropic or isotropic pressure. The accuracy of the formalism is verified by a numerical calculation of implicit dispersion relations in complex Fourier space. The analysis shows that nonuniformity plays a critical role in plasma instability, while the flow velocity and anisotropic pressures determine the growth rate of the instability. Lastly, the instability diagram and associated instability criterion for anisotropy-driven instability are introduced as applications of the formalism.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Jets from shocked metal surfaces with grooves: Missing experiments

Many studies have investigated the mass outflows generated when a planar shock transits an imperfect (“defected”) metal surface, where the defects are symmetric triangular or sinusoidal grooves. Yet a fundamental question remains unanswered: how does the quantity of outflow mass and its maximum velocity vary as a function of the groove cross-sectional aspect ratio? We identify two sets of missing experiments that must be addressed to answer the question. The aspect ratio (groove depth over width) is equivalently represented by θ, the cross-sectional half angle, or by η 0 k, the amplitude multiplied by an effective wavenumber. Low θ (high η 0 k) grooves comprise the first set of missing experiments, which are necessary to determine the validity of theoretical predictions of the nonlinear regime (η 0 k ≥ 1, θ < 57.5°). The second set of missing experiments are those in which the volume of the groove (or equivalently, the axial cross-sectional area) has been held constant as θ or η 0 k are varied. Such experiments are necessary to independently measure the effects of variations in groove volume and groove aspect ratio on the resulting jets.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Ephemeral antibubbles: Spatiotemporal evolution from direct numerical simulations

Antibubbles, which consist of a shell of a low-density fluid inside a high-density fluid, have several promising applications. We show, via extensive direct numerical simulations (DNSs), in both two and three dimensions, that the spatiotemporal evolution of antibubbles can be described naturally by the coupled Cahn-Hilliard-Navier-Stokes (CHNS) equations for a binary fluid. Our DNSs capture elegantly the gravity-induced thinning and breakup of an antibubble via the time evolution of the Cahn-Hilliard scalar-order-parameter field $\phi$, which varies continuously across interfaces, so we do not have to enforce complicated boundary conditions at the moving antibubble interfaces. To ensure that our results are robust, we supplement our CHNS simulations with sharp-interface volume-of-fluid DNSs. We track the thickness of the antibubble and calculate the dependence of the lifetime of an antibubble on several parameters; we show that our DNS results agree with various experimental results; in particular, the velocity with which the arms of the antibubble retract after breakup scales as σ 1/2 , where σ is the surface tension.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

Global Non-axisymmetric Hall Instabilities in a Rotating Plasma

Non-axisymmetric, flow-driven instabilities in the incompressible Hall-MHD model are studied in a differentially rotating cylindrical plasma. It is found that, in the Hall-MHD regime, both whistler waves and ion-cyclotron waves can extract energy from the flow shear, resulting in two distinct branches of global instability. The non-axisymmetric whistler modes grow significantly faster than non-axisymmetric, ideal MHD modes. A discussion of the global whistler instability mechanism is presented in the large-ion-skin-depth, “electron-MHD” limit. When the magnetic field is azimuthal, a subset of the whistler modes having zero axial wave number are uncovered to be destabilized by the “corotation amplifier” mechanism. It is observed that the effect of the Hall term on the non-axisymmetric modes can be appreciable when d i is on the order of a few percent of the width of the cylindrical annulus. Distinct global modes emerge in the strong Hall-MHD regime at significantly stronger magnetic fields than those required for unstable global MHD modes, as the Hall effect weakens the stabilizing “field-line bending” by decoupling ion motion from the magnetic field. These global non-axisymmetric modes may play an important role in weakly ionized accretion disks.

Alfven waves↗
DOE OSTI2025

Kelvin–Helmholtz instability under stabilizing parallel magnetic field in nonhomogeneous compressible MHD flows

We study the Kelvin–Helmholtz instability (KHI) for the general case of a compressible, nonhomogeneous, magnetized plasma flow. The study is limited to a vortex sheet interface with an imposed parallel magnetic field. We introduce a new formalism based on a convective Mach number M c , a convective Alfvénic Mach number M Ac , and a total convective Mach number that combines the two. We derive an analytic expression of the KHI growth rate for a homogeneous flow (i.e., zero Atwood number, A=0) that converges toward both the expression for unmagnetized compressible flow and Chandrasekhar's expression for magnetized incompressible flow. Otherwise, the dispersion relation is solved numerically and allows deriving general stability diagrams of magnetized KHI for the triplet (A, M c , β −plasma) parameters. We show these parameters uniquely define all configurations for a parallel magnetic field. We also construct diagrams with respect to the convective Alfvénic Mach number, the β − plasma parameter, or the magnetic field showing which magnetic field strength is required for stabilizing a given shear flow. The theoretical growth rates are compared with 18 simulations made with the GAMERA code, currently used for 3D magnetospheric simulations. Finally, we apply our results to the analysis of a past KHI experiment performed at the OMEGA laser facility, showing linear theory succeeds to provide accurate estimates of the growth rate at early times. We further discuss how our results can inform future experiments in the high-Mach magnetized regime at the National Ignition Facility. Possible limitations of the study due to resistive, mixing, or turbulence effects are discussed.

compressible flows↗