Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “finite-volume methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

An explicit finite-volume time-marching procedure for turbulent flow calculations

A method was developed which calculates two-dimensional, transonic, viscous flow in ducts. The finite-volume, time-marching formulation is used to obtain steady flow solutions of the Reynolds-averaged form of the Navier-Stokes equations. The entire calculation is performed in the physical domain. Control volumes are chosen so that smoothing of flow properties, typically required for stability, is not required. Different time steps are used in the different governing equations. A new pressure interpolation scheme is introduced which improves the shock capturing ability of the method. A multi-volume method for pressure changes in the boundary layer allows calculations which use very long and thin control volumes (length/height - 1000). The method is compared with two test cases. Essentially incompressible turbulent boundary layer flow in an adverse pressure gradient is calculated and the computed distributions of mean velocity and shear are in good agreement with the measurements. Transonic viscous flow in a converging diverging nozzle is calculated; the Mach number upstream of the shock is approximately 1.25. The agreement between the calculated and measured shock strength and total pressure losses is good.

Nicholson, Stephen↗
NASA NTRS1986

Development of an explicit time marching procedure for laminar and turbulent flow

A finite-volume based, time-marching method for turbulent and laminar flows is described. Extensions to the computational procedure to allow the handling of shock induced separation and large regions of strong backflow are emphasized. Two test cases are considered, the United Technologies Research Center (UTRC) separated and reattached turbulent boundary layer and the strong shock case in the McDonnell Douglas Research Lab (MDRL) transonic diffuser G. The extended method worked well on the UTRC flow with a boundary layer blockage of 58% and a maximum backflow velocity of 37% of the local maximum free-stream velocity. It also worked well on the MDRL diffuser with a shock Mach number of 1.353 and a maximum backflow velocity of -71.7 m/s. A Mach number dependent interpolation formula for effective pressure was developed for use in density-update time-marching methods.

Source record↗
NASA NTRS1981

Accelerated finite-volume calculation of transonic potential flows

A fully conservative finite-volume algorithm is used to calculate transonic potential flows past isolated airfoils and through two-dimensional channels. The difference equations are solved by a multigrid technique which uses an alternating direction implicit method as a smoothing algorithm. The finite-volume formulation provides a framework within which to treat flows past complicated geometries, while the multigrid/alternating direction scheme provides rapid convergence of the solution to very small residuals.

Jameson, A.↗
NASA NTRS1986

Explicit finite-volume time-marching calculations of total temperature distributions in turbulent flow

A method was developed which calculates two-dimensional, transonic, viscous flow in ducts. The finite volume, time-marching formulation is used to obtain steady flow solutions of the Reynolds-averaged form of the Navier-Stokes equations. The entire calculation is performed in the physical domain. This paper investigates the introduction of a new formulation of the energy equation which gives improved transient behavior as the calculation converges. The effect of variable Prandtl number on the temperature distribution through the boundary layer is also investigated. A turbulent boundary layer in an adverse pressure gradient (M = 0.55) is used to demonstrate the improved transient temperature distribution obtained when the new formulation of the energy equation is used. A flat plate turbulent boundary layer with a supersonic free-stream Mach number of 2.8 is used to investigate the effect of Prandtl number on the distribution of properties through the boundary layer. The computed total temperature distribution and recovery factor agree well with the measurements when a variable Prandtl number is used through the boundary layer.

Nicholson, Stephen↗
NASA NTRS1987

An L-U implicit multigrid algorithm for the three-dimensional Euler equations

An LU implicit multigrid scheme is developed for the calculation of three-dimensional transonic flow through rotating cascades. This numerical method solves the unsteady Euler equations of gas dynamics in a finite-volume form. The implicit scheme makes it possible to take a much larger time step than is normally permitted in most explicit schemes, while the multigrid method is incorporated to accelerate the convergence rate for steady state calculations. Using this method, computational storage requirements are comparable to those of explicit schemes, while operation counts are considerably less than those found in the more widely-used ADI schemes.

Yokota, Jeffrey W.↗
NASA NTRS1983

Multi-grid calculation of three-dimensional transonic potential flows

A multi-grid algorithm has been developed to speed the iterative convergence of calculations for the transonic potential flow past swept wings and wing-fuselage combinations. The method is based upon a fully-conservative, finite-volume approximation to the steady potential equation which is second-order accurate everywhere in the flow field except near shock waves. The multi-grid scheme is incorporated within the framework of an alternating successive-line-overrelaxation (SLOR) solver of the difference equations. Computed results confirm the second-order accuracy of the scheme, and demonstrate the effectiveness of the multi-grid procedure.

Caughey, D. A.↗
NASA NTRS1981

Numerical method for gas dynamics combining characteristic and conservation concepts

An efficient implicit numerical method that solves the compressible Navier-Stokes equations in arbitrary curvilinear coordinates by the finite-volume technique is presented. An intrinsically dissipative difference scheme and a fully implicit treatment of boundary conditions, based on characteristic and conservation concepts, are used to improve stability and accuracy. Efficiency is achieved by using a diagonal form of the implicit algorithm and spatially varying time-steps. Comparisons of various schemes and methods are presented for one- and two-dimensional flows, including transonic separated flow past a thick circular-arc airfoil in a channel. The new method is equal to or better than a version of MacCormack's hybrid method in accuracy and it converges to a steady state up to an order of magnitude faster.

Coakley, T. J.↗
NASA NTRS1985

Numerical solution of the Euler equations for high-speed, blended wing-body configurations

Simulation of high-speed three-dimensional flow about blended wing-body combinations is investigated. A finite-volume explicit scheme with Runge-Kutta time integration is used to solve the compressible Euler equations in order to simulate the flow. The method, augmented by carefully chosen dissipative terms and convergence accelerators such as enthalpy damping and maximum local time-stepping, has been found to be very efficient in solving high-speed flows involving strong shocks. An analytic method for generating the body geometry and an algebraic method for quasi-three-dimensional grid generation are described. Results are presented for various blended wing-body configurations at different Mach numbers and angles of attack.

Moitra, A.↗
NASA NTRS2026

A Modular Conjugate Heat Transfer Optimization Framework for Thermal Management of Electric Aircraft

Conjugate heat transfer (CHT) analysis and optimization is a powerful method for improving thermal management, as it simultaneously resolves the temperature distribution in both fluid and solid domains. This paper presents a modular, discrete adjoint-based CHT optimization capability integrated within the OpenMDAO/MPhys framework. A unique feature of the proposed framework is its flexibility to extend to multidisciplinary optimization, including aero-structural-thermal applications. The fluid domain is modeled using a finite-volume Computational Fluid Dynamics (CFD) solver, and the solid domain with a conduction heat transfer solver. A mixed Neumann-Dirichlet boundary condition is developed to enable full submersion of the solid geometry within the fluid domain, while ensuring consistent temperature and heat flux coupling at the CHT interface. Gradient-based optimization is performed; the gradients are efficiently computed using the discrete adjoint solvers implemented in DAFoam. To demonstrate the method, this paper considers two cases related to electric aircraft thermal management: a U-bend heat exchanger and an actively cooled battery pack. The U-bend case aims to minimize pressure loss while maximizing heat flux by changing the pipe geometry. The optimized design reduces pressure loss by 52.7% and increases total heat flux by 2.3%. In the battery pack case, a 3-by-3 cell configuration is cooled by ambient airflow, with constant heat generation prescribed in the cells. The battery casing shape serves as the design variable, and the objective function is a weighted sum of pressure loss and pack weight, subject to a maximum temperature constraint. The optimized design achieves a 44.6% reduction in pressure loss and a 1.5% reduction in weight, while satisfying the thermal constraint. To ensure the reliability of the optimized designs, this study validates coarse-mesh, steady-state predictions against fine-mesh unsteady simulations, demonstrating consistency within acceptable errors. This work demonstrates the potential of the developed framework to enable rapid, high-fidelity design of thermal management systems for electric aircraft.

heat transfer↗
NASA NTRS1984

An implict LU scheme for the Euler equations applied to arbitrary cascades

An implicit scheme for solving the Euler equations is derived and demonstrated. The alternating-direction implicit (ADI) technique is modified, using two implicit-operator factors corresponding to lower-block-diagonal (L) or upper-block-diagonal (U) algebraic systems which can be easily inverted. The resulting LU scheme is implemented in finite-volume mode and applied to 2D subsonic and transonic cascade flows with differing degrees of geometric complexity. The results are presented graphically and found to be in good agreement with those of other numerical and analytical approaches. The LU method is also 2.0-3.4 times faster than ADI, suggesting its value in calculating 3D problems.

Buratynski, E. K.↗
NASA NTRS1987

Prospects for Eulerian CFD analysis of helicopter vortex flows

The applicability of current finite-volume CFD algorithms based on the Euler equations to the vortex flow over a helicopter in forward flight is investigated analytically. The general characteristics of the flow are reviewed; existing Euler, Navier-Stokes, perturbation, high-order, and adaptive methods are briefly characterized; and a novel Eulerian/Lagrangian approach with entropy and vorticity corrections is presented in detail. Numerical results for simple convection of a finite-core Lamb vortex moving downstream with its axis perpendicular to the flow are presented in graphs, and the possibility of extending the method to three-dimensional, viscous, and shock flows is discussed.

Drela, Mark↗
NASA NTRS1986

Euler solutions for high-speed flow about complex three-dimensional configurations

A numerical algorithm based on a finite-volume explicit scheme with Runge-Kutta time integration of the Euler equations is presented for calculating high-speed three-dimensional flow about complex aerospace configurations. The use of enhancing factors such as artificial dissipative terms, enthalpy damping and local time-stepping are described. An algebraic method for generating quasi-three-dimensional computational grids for realistic aerospace configurations is presented. Computed results for various three-dimensional bodies at different Mach numbers and angles of attack have been obtained using the methods for grid-generation and flow simulation. Comparison of computed and experimental data for an advanced tactical aircraft-like configuration is presented, and a reasonable agreement of the data is noticed.

Moitra, A.↗
NASA NTRS1983

A time-split finite-volume algorithm for three-dimensional flow-field simulation

A general finite-volume algorithm is developed for solving three-dimensional, time-dependent, compressible Navier-Stokes equations for high Reynolds number flows over an arbitrary geometry. This algorithm adapts MacCormack's (1982) explicit-implicit scheme to a time-split, three-dimensional finite-volume concept in a general coordinate system. It is shown that the thin-layer approximation in all three spatial directions significantly reduces the evaluation of viscous terms and allows the algorithm to solve more complicated geometries with all boundaries in two or all three directions. The calculated results using this method are found to be in good agreement with the experimental measurements of a blunt-fin induced shock wave and boundary-layer interaction problems. Observations of the existence of peak pressure, primary horseshoe and secondary vortices, and reversed supersonic zones show that computational fluid dynamics can effectively supplement the wind tunnel tests for aerodynamic design as well as for understanding basic fluid dynamics.

Hung, C. M.↗
NASA NTRSDate not supplied

Aerothermal Shape Optimization of Actively-Cooled Battery Packs using Conjugate Heat Transfer

Thermal management for battery is important for electric aircraft because battery temperature is critically important to vehicle safety, and it also has direct impact on the efficiency of the battery system. Because ambient air is a readily available resource for aircraft, this paper considers an active cooling concept with forced convection of ambient air through the battery pack. Conjugate heat transfer analysis is used to solve the coupled aero-thermal problem, which consists of a finite-volume computational fluid dynamics solver for the fluid domain, and a conduction heat transfer solver for the solid domain. A mixed Neumann and Dirichlet boundary condition is developed for the fluid-solid interface, which allows the solid domain to completely submerge in the fluid domain. A gradient-based optimization method is adopted, and the discrete adjoint approach implemented in DAFoam is used to efficiently compute the gradients. The aero-thermal coupling for primal analysis and gradient computation is handled using the OpenMDAO-based MPhys framework. A constant heat source is prescribed for the battery cells, and the battery shape (design variable) is optimized to minimize cooling pump power and battery weight (composite objective function) while keeping the battery temperature below a threshold (constraint). The optimized design achieves a 44.6% and 1.5% reduction in the cooling pump power and battery weight, respectively, and the maximal temperature constraint is satisfied. This work has the potential to reduce battery-pack weight, improve performance, and reduce the weight of thermal management systems for electric vertical take-off and landing aircraft.

thermal management↗
NASA NTRS1982

Transonic potential flow and coordinate generation for bodies in a wind tunnel

An accurate method has been developed for computation of transonic potential flow about a 2-D lifting airfoil or an axisymmetric body in a wind tunnel. The computational mesh is nearly orthogonal everywhere and is generated by a sequence of Schwarz-Christoffel transformations and shearings to obtain an '0' grid near the body. A conservative finite-volume scheme for the full-potential equation and exact boundary conditions is used together with 'retarded' density to solve efficiently transonic flow with embedded shocks and large regions of supersonic flow. Supersonic free-stream flows are also solved with captured bow shocks and embedded subsonic regions.

Doria, M. L.↗
NASA NTRS1982

Singularity embedding method in potential flow calculations

The so-called H-type mesh is used in a finite-element (or finite-volume) calculation of the potential flow past an airfoil. Due to coordinate singularity at the leading edge, a special singular trial function is used for the elements neighboring the leading edge. The results using the special singular elements are compared to those using the regular elements. It is found that the unreasonable pressure distribution obtained by the latter is removed by the embedding of the singular element. Suggestions to extend the present method to transonic cases are given.

Jou, W. H.↗
NASA NTRS1986

An analysis of finite-difference and finite-volume formulations of conservation laws

Finite-difference and finite-volume formulations are analyzed in order to clear up the confusion concerning their application to the numerical solution of conservation laws. A new coordinate-free formulation of systems of conservation laws is developed, which clearly distinguishes the role of physical vectors from that of algebraic vectors which characterize the system. The analysis considers general types of equations--potential, Euler, and Navier-Stokes. Three-dimensional unsteady flows with time-varying grids are described using a single, consistent nomeclature for both formulations. Grid motion due to a non-inertial reference frame as well as flow adaptation is covered. In comparing the two formulations, it is found useful to distinguish between differences in numerical methods and differences in grid definition. The former plays a role for non-Cartesian grids, and results in only cosmetic differences in the manner in which geometric terms are handled. The differences in grid definition for the two formulations is found to be more important, since it affects the manner in which boundary conditions, zonal procedures, and grid singularities are handled at computational boundaries. The proper interpretation of strong and weak conservation-law forms for quasi-one-dimensional and axisymmetric flows is brought out.

Vinokur, Marcel↗
NASA NTRS1985

Thermodynamic evaluation of transonic compressor rotors using the finite volume approach

Research at NASA Lewis Research Center gave the opportunity to incorporate new control volumes in the Denton 3-D finite-volume time marching code. For duct flows, the new control volumes require no transverse smoothing and this allows calculations with large transverse gradients in properties without significant numerical total pressure losses. Possibilities for improving the Denton code to obtain better distributions of properties through shocks were demonstrated. Much better total pressure distributions through shocks are obtained when the interpolated effective pressure, needed to stabilize the solution procedure, is used to calculate the total pressure. This simple change largely eliminates the undershoot in total pressure down-stream of a shock. Overshoots and undershoots in total pressure can then be further reduced by a factor of 10 by adopting the effective density method, rather than the effective pressure method. Use of a Mach number dependent interpolation scheme for pressure then removes the overshoot in static pressure downstream of a shock. The stability of interpolation schemes used for the calculation of effective density is analyzed and a Mach number dependent scheme is developed, combining the advantages of the correct perfect gas equation for subsonic flow with the stability of 2-point and 3-point interpolation schemes for supersonic flow.

Moore, J.↗