Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fan performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Energy efficient engine. Fan and quarter-stage component performance report

The fan configuration for the general Electric/NASA Energy Efficient Engine was selected following an extensive preliminary design study. The fan has an inlet radius ratio of 0.342 and a specific flowrate of 208.9 Kg/sec/sq. m (42.8 1bm/sec/sq. ft). The design corrected tip speed is 411.5 m/sec (1350 ft/sec) producing a bypass flow total-pressure ratio of 1.65 and a core flow total-pressure ratio of 1.6. The design bypass ratio is 6.8. The aerodynamic design point corresponds to the maximum climb power setting at Mach 0.8 and 10.67 Km (35,000 ft) altitude. The fully-instrumented fan component was tested in the Lynn Large Fan Test Facility in 1981. The overall performance results, reported herein, showed excellent fan performance with the fan meeting all of its component test goals of flow, efficiency and stall margin.

Cline, S. J.↗
NASA NTRS1976

Cold-air performance of a tip turbine designed to drive a lift fan. 1: Baseline performance

Full admission baseline performance was obtained for a 0.4 linear scale of the LF460 lift fan turbine over a range of speeds and pressure ratios without leakage air. These cold-air tests covered a range of speeds from 40 to 140 percent of design equivalent speed and a range of scroll inlet to diffuser exit static pressure ratios from 2.0 to 4.2. Results are presented in terms of specific work, torque, mass flow, efficiency, and total pressure drop.

Haas, J. E.↗
NASA NTRS1975

Summary of model VTOL lift fan tests conducted at NASA Lewis Research Center

Early in this decade three model VTOL lift fan studies were conducted in the NASA Lewis Research Center's 9- by 15-foot V/STOL wind tunnel. The first experiment consisted of crossflow tests of a 15-inch diameter fan installed in a two-dimensional wing. The wing was then used for a study of installation effects on lift fan performance. The model tested consisted of three 5.5-inch diameter tip-turbine driven model VTOL lift fans mounted chord-wise in the two-dimensional wing to simulate a pod-type array. For the third program, a pod was attached to the wing, and an investigation was conducted of the effect of design tip speed on the aerodynamic performance and noise of a 15-inch diameter lift fan-in-pod under static and crossflow conditions.

Diedrich, J. H.↗
NASA NTRS1974

Performance of a model cascade thrust reverser for short-haul applications

Aerodynamic and acoustic characteristics are presented for a cowlmounted, model cascade thrust reverser suitable for short-haul aircraft. Thrust reverser efficiency and the influence on fan performance were determined from isolated fan-driven models under static and forward velocity conditions. Cascade reverser noise characteristics were determined statically in an isolated pipe-flow test, while aerodynamic installation effects were determined with a wind-tunnel, fan-powered airplane model. Application of test results to short-haul aircraft calculations demonstrated that such a cascade thrust reverser may be able to meet both the performance and noise requirements for short-haul aircraft operation. However, aircraft installation effects can be quite significant.

Dietrich, D. A.↗
NASA NTRS1974

Performance of a model cascade thrust reverser for short-haul applications

Aerodynamic and acoustic characteristics are presented for a cowl-mounted, model cascade thrust reverser suitable for short-haul aircraft. Thrust reverser efficiency and the influence on fan performance were determined from isolated fan-driven models under static and forward velocity conditions. Cascade reverser noise characteristics were determined statically in an isolated pipe-flow test, while aerodynamic installation effects were determined with a wind-tunnel, fan-powered airplane model. Application of test results to short-haul aircraft calculations demonstrate that such a cascade thrust reverser may be able to meet both the performance and noise requirements for short-haul aircraft operation. However, aircraft installation effects can be quite significant.

Dietrich, D. A.↗
NASA NTRS1971

Large-scale wind-tunnel investigation of a V/STOL transport model with podded lift fans forward and aft of a low mounted wing

A configuration with outboard pod mounted front fans and rear fans located in the wing trailing-edge and fuselage juncture might have superior induced lift and variation of moment with airspeed. A large scale investigation of this type of configuration was conducted in 40- by 80-foot wind tunnel. The model used was a low wing transport representative of currently operating aircraft. Two lift fans were placed in pods forward of and below the wing with the fan centerline near mid semi-span. Two rear fans were mounted at the wing trailing-edge close to the fuselage with the fan rotor in the wing chord plane. Fan performance was measured statically and with forward speed, and longitudinal aerodynamic characteristics were obtained with the fans operating at various tip-speed ratios.

Hall, L. P.↗
NASA NTRS1972

Aerodynamic characteristics of a large scale lift fan transport model with podded fans forward and lift cruise fans mounted above the wing

The aerodynamic characteristics of a large scale V/STOL transport model powered by tip-turbine driven lift fans were investigated. The model had four fans; the forward fans were mounted in pods forward of the wing at midsemispan. The aft fans were placed in cruise nacelles behind and above the wing. A cascade of variable camber exit louvers was placed behind each of the lift-cruise fans to turn the fan flow in the lift direction for hover and transition to wing supported flight. The wing of the model was mounted above the fuselage, had an aspect ratio of 5.8, sweepback of 35 deg at the quarter chord line and a taper ratio of 0.3. Various configurations of the model were tested to explore the transition speed range. Fan performance, turning effectiveness of the variable camber exit louvers, longitudinal and lateral-directional characteristics with fan operation in crossflow are presented.

Kirk, J. V.↗
NASA NTRS1977

Effects of tip clearance on overall performance of transonic fan stage with and without casing treatment

The overall performance of a transonic fan stage is presented for various tip clearances, with and without casing treatment. The stage was tested with a solid casing, and with open skewed slots and closed skewed slots in the casing over the rotor blade tips. Four nominal nonrotating rotor blade tip clearances from 0.061 to 0.178 centimeter were used. For all three casings, the pressure ratio and efficiency decreased with increasing tip clearance. The stall margin for a given casing also decreased with increasing clearance. At design speed and a given tip clearance, the highest stall margin was obtained with the open-slot casing, and the lowest stall margin was obtained with the solid casing.

Moore, R. D.↗
NASA NTRS1977

Variable pitch fan system for NASA/Navy research and technology aircraft

Preliminary design of a shaft driven, variable-pitch lift fan and lift-cruise fan was conducted for a V/STOL Research and Technology Aircraft. The lift fan and lift-cruise fan employed a common rotor of 157.5 cm diameter, 1.18 pressure ratio variable-pitch fan designed to operate at a rotor-tip speed of 284 mps. Fan performance maps were prepared and detailed aerodynamic characteristics were established. Cost/weight/risk trade studies were conducted for the blade and fan case. Structural sizing was conducted for major components and weights determined for both the lift and lift-cruise fans.

Ryan, W. P.↗
NASA NTRS1972

Fan noise and performance

Tradeoffs between aerodynamic and acoustic properties of various fan configurations led to the selection of a variety of fans that produce noise levels in the range of 100 to 120 PNdb. Fan configuration and design pressure ratio required for specific mission operations depend in part on the type of mission to be performed. Noise data obtained for single-stage low speed fans, single-stage high speed fans, and two-stage fan engines are presented in table form.

Kramer, J. J.↗
NASA NTRS1980

CF6 jet engine performance improvement: New fan

As part of the NASA sponsored engine component improvement program, and fan package was developed to reduce fuel consumption in current CF6 turbofan aircraft engine. The new fan package consist of an improved fan blade, reduced fan tip clearance due to a fan case stiffener, and a smooth fan casing tip shroud. CF6 engine performance and acoustic tests demonstrated the predicted 1.8% improvement in cruise sfc without an increase in engine noise. Power management thrust/fan speed characteristics were defined. Mechanical and structural integrity was demonstrated in model fan rotor photoelastic stress tests, full-size fan blade bench fatigue tests, and CF6 engine bird ingestion, crosswind, and cyclic endurance tests. The fan was certified in the CF6-500c2/E2 engines and is in commerical service on the Boeing 747-200, Douglas DC-10-30, and Atrbus industrie A300B aircraft.

Fasching, W. A.↗
NASA NTRS1972

Quiet engine design highlights

Three high performance fans were designed, built, and tested, accumulating 444 hours. All three fans are both aerodynamically and mechanically suitable for direct incorporation into engine applications. Two turbofan demonstrators to evaluate both low- and high-speed fan systems were also designed, built, and tested. All components and engine systems are demonstrating high reliability. These components have demonstrated advanced state-of-the-art in acoustics, aerodynamics, and mechanical design.

Koff, B. L.↗
NASA NTRS1977

Preliminary QCSEE program - Test results

Preliminary results are reported for the Quiet Clean Short-haul Experimental Engine (QCSEE) program initiated by NASA in 1974 to develop propulsion system technology suitable for powered-lift short-range commercial aircraft. The QCSEE technology also has applications to the proposed U.S. Navy V/STOL aircraft. Emphasis in the QCSEE program is placed on developing engines with low noise characteristics; in addition, the power plants are required to conform to EPA 1979 pollutant emissions standards. Thrust performance, fan design, and thrust/weight ratio are discussed for both the over-the-wing and under-the-wing engine configurations under study.

Ciepluch, C. C.↗
NASA NTRS1974

Quiet Clean Short-Haul Experimental Engine (QSCEE). Preliminary analyses and design report, volume 1

The experimental propulsion systems to be built and tested in the 'quiet, clean, short-haul experimental engine' program are presented. The flight propulsion systems are also presented. The following areas are discussed: acoustic design; emissions control; engine cycle and performance; fan aerodynamic design; variable-pitch actuation systems; fan rotor mechanical design; fan frame mechanical design; and reduction gear design.

Source record↗
NASA NTRS1982

Rotorcraft convertible engines for the 1980s

Two rotorcraft studies were executed. The goal was to identify attractive techniques for implementing convertible powerplants for the ABC, Folded Tilt Rotor, and X-wing type high speed, high-L/D rotorcraft; to determine the DOC and fuel savings benefits achieved thereby; and to define research required to bring these powerplants into existence by the 1990's. These studies are reviewed herein and the different methods of approach are pointed out as well as the key findings. Fan shaft engines using variable inlet guide vanes or torque converters, and turboprop powerplants appear attractive. Savings in DOC and fuel consumption of over 15 percent are predicted in some cases as a result of convertible engine use rather than using separate engines for the thrust and the shaft functions. Areas of required research are fan performance (including noise), integrated engine/rotorcraft control, torque converters, turbine design, airflow for rotorcraft torque control, bleed for lift flow, and transmissions and clutches.

Eisenberg, J. D.↗
NASA NTRS1976

Aerodynamic performance of flared fan nozzles used as inlets

Tests were conducted in a low speed wind tunnel to determine the aerodynamic performance of several flared fan nozzles. Each of the flared nozzles was a downstream-facing inlet to a model fan that was used to simulate a variable pitch fan during reverse thrust operation. The total pressure recovery of each of the flared nozzles as well as that of an unflared nozzle and a serrated flare nozzle was obtained for comparison. The aerodynamic performance of a selected flared nozzle was considered in further detail. The nozzle surface pressures for a flared nozzle were also determined. Results indicated that the differences in aerodynamic performance among the nozzles were most apparent at the wind-tunnel-off condition. A nonzero free stream velocity significantly reduced the perforamnce of all the nozzles, and crosswind flow (free stream flow perpendicular to the model axis) further reduced the performance of the nozzles. The unflared nozzle and the serrated flare nozzle had reduced aerodynamic performance compared to a solid surface flared nozzle.

Dietrich, D. A.↗