Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “extrusion force”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

34 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Additive Manufacturing of Isotropic NdFeB PPS Bonded Permanent Magnets

Extrusion based additive manufacturing of polymer composite magnets can increase the solid loading volume fraction with greater mechanical force through the printing nozzle as compared to traditional injection molding process. About 63 vol% of isotropic NdFeB magnet powders were compounded with 37 vol% of polyphenylene sulfide and bonded permanent magnets were fabricated while using Big Area Additive Manufacturing without any degradation in magnetic properties. The polyphenylene sulfide bonded magnets have a tensile stress of 20 MPa, almost double than that of nylon bonded permanent magnets. Additively manufactured and surface-protective-resin coated bonded magnets meet the industrial stability criterion of up to 175 °C with a flux-loss of 2.35% over 1000 h. They also exhibit better corrosion resistance behavior when exposed to acidic (pH = 1.35) solution for 24 h and also annealed at 80 °C over 100 h (at 95% relative humidity) over without coated magnets. Thus, polyphenylene sulfide bonded, additively manufactured, protective resin coated bonded permanent magnets provide better thermal, mechanical, and magnetic properties.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Porosity evolution during heating of copper made from powder by friction extrusion

Here, friction extrusion was used to compact and extrude solid copper rod from feedstock powders. Following extrusion, considerable porosity was observed throughout the extrudate cross section due to the entrained porosity in the feedstock material and the extrusion process. The thermal stability of the extrudate was investigated via a series of heat treatments. Porosity evolution exhibited three distinct stages—an unchanged plateau (0°C–300°C) followed by an abrupt increase (400°C–500°C) and ultimately a reduction, as the temperature increases (>500°C). The peak porosity measured was ~25%. The underlying driving force for pore evolution is described as the competition between the internal pore pressure, material strength, and sintering kinetics, as a function of temperature. The observed porosity evolution and driving force are not expected to be limited to copper. Thus, this manuscript reveals an important consideration regarding elevated-temperature thermal stability as advanced manufacturing methods involving direct powder extrusion are explored.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Pressure-based process monitoring of direct-ink write material extrusion additive manufacturing

As additive manufacturing (AM) has become a reliable method for creating complex and unique hardware rapidly, the quality assurance of printed parts remains a priority. In situ process monitoring offers an approach for performing quality control while simultaneously minimizing post-production inspection. For extrusion printing processes, direct linkages between extrusion pressure fluctuations and print defects can be established by integrating pressure sensors onto the print head. In this work, the sensitivity of process monitoring is tested using engineered spherical defects. Pressure and force sensors located near an ink reservoir and just before the nozzle are shown to assist in identification of air bubbles, changes in height between the print head and build surface, clogs, and particle aggregates with a detection threshold of 60–70% of the nozzle diameter. Visual evidence of printed bead distortion is quantified using optical image analysis and correlated to pressure measurements. Importantly, this methodology provides an ability to monitor the quality of AM parts produced by extrusion printing methods and can be accomplished using commonly available pressure-sensing equipment.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effect of grain structure and strain rate on dynamic recrystallization and deformation behavior: A phase field-crystal plasticity model

Herein, a phase field (PF)-crystal plasticity (CP) model has been developed to study the effects of initial grain structures, recrystallized grain orientation, and strain rates on dynamic recrystallization and deformation behavior under stress states typical of the Shear Assisted Processing and Extrusion (ShAPE) process. The model takes the geometrically necessary dislocation density as the nucleation criterion for recrystallization and minimizes the deformation energy as the driving force of recrystallized grain growth. Using this model, the effects of grain orientations and strain rates on dynamic recrystallization and deformation behavior were simulated. The results demonstrate that (1) a polycrystalline structure with the texture observed in ShAPE process has the lowest yield stress under the ShAPE stress conditions, (2) the recrystallized grains with the texture observed in ShAPE process largely soften the materials, and (3) higher shear strain rate or rotation speed results in larger magnitude of material softening.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Solid Phase Processing of Mg-Al-Mn-Ca for High Strength and Ductility

While rare-earth Mg alloys have remarkable properties for high strength applications, lower cost alternatives are necessary for the widespread industry use of Mg. Ca added Mg alloys have shown promise as an alternative to rare-earth alloys. Ca-based precipitates can reduce basal texture, reduce casting porosity, and increase mechanical strength. However, the accumulation of Ca-based precipitates along inter-dendritic regions can severely limit ductility. Here, we apply two solid phase processing techniques, friction stir processing and shear assisted processing and extrusion, to produce wrought microstructure sheet and extruded tubes from a cast Mg-Al-Mn-Ca alloy. Ductility of the alloy is enhanced by densification under applied force and elevated temperature, grain refinement, and refinement of (Al,Mg)-Ca based precipitate.

Garcia, David↗
DOE OSTI2023

Monitoring the compaction of single DNA molecules in Xenopus egg extract in real time

DNA compaction is required for the condensation and resolution of chromosomes during mitosis, but the relative contribution of individual chromatin factors to this process is poorly understood. We developed a physiological, cell-free system using high-speed Xenopus egg extracts and optical tweezers to investigate real-time mitotic chromatin fiber formation and force-induced disassembly on single DNA molecules. Compared to interphase extract, which compacted DNA by ~60%, metaphase extract reduced DNA length by over 90%, reflecting differences in whole-chromosome morphology under these two conditions. Depletion of the core histone chaperone ASF1, which inhibits nucleosome assembly, decreased the final degree of metaphase fiber compaction by 29%, while depletion of linker histone H1 had a greater effect, reducing total compaction by 40%. Compared to controls, both depletions reduced the rate of compaction, led to more short periods of decompaction, and increased the speed of force-induced fiber disassembly. In contrast, depletion of condensin from metaphase extract strongly inhibited fiber assembly, resulting in transient compaction events that were rapidly reversed under high force. Altogether, these findings support a speculative model in which condensin plays the predominant role in mitotic DNA compaction, while core and linker histones act to reduce slippage during loop extrusion and modulate the degree of DNA compaction.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Integrating helicoid channels for passive control of fiber alignment in direct-write 3D printing

3D printing of fiber-reinforced composites has been receiving increasing attention as an efficient additive approach enabling lightweight, functional, and high-performance components required for industrial applications. The properties of fiber composites significantly depend on internal microstructures, including fiber orientation, distribution, and degree of alignment. Although multiple strategies have been introduced for controlling the fiber composites microstructures, these strategies are mostly active approaches relying on additional control of mechatronics parts, external forces, or intentionally introduced unstable flows inside narrow nozzles. These methods suffer from higher risk of nozzle clogging and requiring extra parts in 3D printing. Here, we introduce helicoid channels into extrusion system as a passive approach to control the fiber alignment without any additional moving parts in direct-write 3D printing. The helicoid channels automatically guide the composite inks and align fibers before flowing into narrow nozzle space, avoiding clogging and improving printability. The analyses indicate that both helicoid surface to volume ratio and helix angle affect the pre-alignment of fibers, leading to tunable mechanical properties of printed fiber-reinforced composites with increased stiffness and strength up to 77.6% and 47.8%, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Ultrasound Manipulation and Extrusion of Active Nanorods

Abstract Synthetic self‐propelled nano and microparticles have a growing appeal for targeted drug delivery, collective functionality, and manipulation at the nanoscale. However, it is challenging to control their positions and orientations under confinement, e.g., in microchannels, nozzles, and microcapillaries. This study reports on the synergistic effect of acoustic and flow‐induced focusing in microfluidic nozzles. In a microchannel with a nozzle, the balance between the acoustophoretic forces and the fluid drag due to streaming flows generated by the acoustic field controls the microparticle's dynamics. This study manipulates the positions and orientations of dispersed particles and dense clusters inside the channel at a fixed frequency by tuning the acoustic intensity. The main findings are: first, this study successfully manipulates the positions and orientations of individual particles and dense clusters inside the channel at a fixed frequency by tuning the acoustic intensity. Second, when an external flow is applied, the acoustic field separates and selectively extrudes shape‐anisotropic passive particles and self‐propelled active nanorods. Finally, the observed phenomena are explained by multiphysics finite‐element modeling. The results shed light on the control and extrusion of active particles in confined geometries and enable applications for acoustic cargo (e.g., drug) delivery, particle injection, and additive manufacturing via printed self‐propelled active particles.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Drag Coefficient Analysis of Arbitrary Fragment Geometry with Emphasis on Meshing Sensitivity Studies.

This report characterizes Mach number effects in the hypersonic range from Mach 3 to Mach 7 for an arbitrary, computationally generated fragment. Force and moment coefficients in the x, y, z direction were successfully obtained and resulting trends were compared with theoretical expectations. Three orientations were tested in the form of unit vectors: [1,0,0], [0,1,0], and [0,0,1]; these represent the i, j, k principle axes. The final results ultimately showcased a trend very similar to that shown in previous literature — drag coefficients for a given orientation decreased with increasing Mach number by a very small amount in the hypersonic range. It was therefore concluded that the aerodynamic quantities used to obtain the fragment trajectory at low hypersonic Mach numbers (such as Mach 3) can be used to characterize the aerodynamic qualities at higher hypersonic Mach numbers (Mach 5, 7) with a reasonably small margin. A sensitivity study was also conducted which ultimately defined drag effects as a result of changing grid spacing and normal extrusion parameters for the unstructured tetrahedral mesh used in the simulation. Further work can be done in the form of experimental validation, specifically with regards to wind tunnels and ballistic range testing. Error can be reduced by testing more mesh variabilities and capturing a larger amount of fragment orientations. The results for force and moment characteristics dependent on meshing parameters and high Mach numbers are satisfactory and consistent with expected trends.

42 ENGINEERING↗
DOE OSTI2025

Conclusions • Multimaterial and isotopically-labeled specimens were successfully fabricated via FFF-AM • Raman spectroscopy, atomic force microscopy, and neutron scattering show promise for direct measurements of interlayer diffusion in the multimaterial and isotopically-labeled specimens • Although isotopically-labeled specimens offer the greatest potential for experimentally verifying FFF-AM process models, substituting hydrogen with deuterium alters the thermal and rheological properties of the HDPE polymer

Multimaterial and Isotopically Labeled Specimen Fabrication via Material Extrusion Additive Manufacturing for Interlayer Diffusion Analysis

Jones, Haley W. [Savannah River National Laborator↗
DOE OSTI2026

Design, characterization and shape recovery behavior of 3D/4D printed shape memory polymers (SMPs)

Shape memory polymers (SMPs) represent a paradigm shift in material science, uniquely capable of undergoing reversible shape transformations triggered by external stimuli, positioning them as pivotal in developing next-generation biomedical devices, aerospace components, and adaptive structures. Extensive research has been done on SMPs with a major focus on high-temperature programming methods, which can limit energy efficiency and applicability with temperature-sensitive materials. Additionally, while various SMP blends have demonstrated great potential, limited work has been done on the suitability for 3D printing these materials, particularly under high-strain and ambient temperature programming conditions. In this study, a three-component optimized SMP composition was evaluated by 3D printing via the Material Extrusion (MEX) technique and investigating its ambient temperature-programming behavior at high strains. The SMP formulation studied was a tailored blend of thermoplastic polyurethane (TPU), polycaprolactone (PCL), and an octadecane diol-based copolymer (OBC) that exhibits robust shape memory behavior, high strain tolerance, and efficient force generation. Rigorous thermal, mechanical, and shape recovery analyses, along with optimized printing parameters and consistent shape recovery rates of up to 90%, were achieved under dynamic mechanical analysis (DMA), even under ambient programming conditions. This work demonstrates the SMP composition’s potential for adaptive, self-deployable systems with 4D printing characteristics ideal for bio-inspired structures and artificial muscle fibers.

Sudan, Kavish [University of Louisville, KY]↗
DOE OSTI2021

Blending Polyurethane Thermosets Using Dynamic Urethane Exchange

Recycling crosslinked polyurethanes (PUs) is accomplished through mechanical or chemical processes that are energy-intensive or produce plastics of lesser value. Polymer recycling processes are notably intolerant of polymer mixtures, yet the ability to reprocess and compatibilize two or more crosslinked PUs together will make this process more amenable to mixed waste streams while offering an opportunity to tune the properties of the recycled polymer products. Here, we blend a rigid polyester PU and a soft polyether PU using twin-screw extrusion to yield materials with tunable mechanical properties based on the feed composition. Their material properties were compared to those of compression-molded reprocessed blends and blends where the monomers were mixed prior to synthesis. The extruded materials showed similar mechanical and thermal properties to newly prepared blends and had higher-value mechanical properties compared to the samples reprocessed via compression molding. The morphologies of the blends were observed using phase imaging via atomic force microscopy to show that there is less phase separation in the extruded materials compared to compression-molded blends. The mechanical properties of these materials were tunable from soft to elastomeric to rigid based on the feed composition, and this tunability was demonstrated through four consecutive reprocessing cycles, through which the mechanical properties were steadily varied from rigid to soft by incorporating increasing amounts of soft polyether PU material. Here, this blending method for reprocessing mixed waste compatibilizes different PUs and provides a means to tune the mechanical properties of a PU product, even if starting from waste streams of varying compositions. As such, this process represents an intriguing new approach for polymer reprocessing.

Extrusion↗
DOE OSTI2022

Processing of hollow sections

A system and method provide a material with uniform micro-structure. In an embodiment, an equal channel angular extrusion system includes an interior mandrel. The interior mandrel includes an expanding shear material section and a contracting shear material section. In addition, the system includes a material. The material is disposed about a portion of the interior mandrel. Moreover, the system includes a pressure application device. The pressure application device applies pressure to the material to force the material to contact the expanding shear material section to provide an expanded post-shear material section. Pressure from the pressure application device applies pressure to the material to force the expanded post-shear material section to contact the contracting shear material section to provide a contracted shear material section.

Barber, Robert E.↗
DOE OSTI2024

The effect of stretching on polyamide – 6: assessment of crystallinity, mechanical properties, and surface roughness

Polyamide-6 (PA6), or nylon-6, is a widely used low-cost polymer material for various applications. Manufacturing PA6 into fibers involves a spinning process such as melt extrusion, which orients the polymer chains into a semicrystalline structure. When stretching the produced fibers to high strains, the PA6 fibers transition the metastable gamma phase back into the stable gamma phase. The effects of these large stretches on mechanical properties have not been explored after the stretch has been released. In this study, the effects on mechanical properties were studied by stretching the PA6 fibers from 10% to 50% tensile strain and subsequently releasing the fibers. The stretched fibers were characterized by X-ray diffraction and atomic force microscopy to determine the changes to the crystal structure and surface roughness. The stretched fibers were then tensile tested to failure and the tensile properties were examined. The stress-strain curves on the post-stretched PA6 fibers showed clear softening in the fibers with lower initial moduli after 30% stretching. Furthermore, these results may hold a clue to softening of fibers in applications with repeated loading and have implications for mechanical stability and fatigue of this polymeric material.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Large-scale reactive thermoset printing: Complex interactions between temperature evolution, viscosity, and cure shrinkage

Thermoset composites are strong candidates for large-scale material extrusion additive manufacturing (AM). However, uncured thermoset composites become unstable as print height increases. Here, chemical initiation of vinyl ester immediately before deposition was used to suppress collapse and enable large-scale thermoset printing. Structural stability was assessed by printing thin walls at various layer times and monitoring thermal gradients with an infrared camera. Stable printing was observed at a layer time of 4.50 min, approximately half the gel time of the material (8 min). Self-weight collapse occurred at short layer time (0.68 min), whereas warpage occurred at long layer time (6.50 min). Here, a new behavior was discovered at intermediate layer time (2.25 min) where the heat generated by the reaction causes new, un-gelled layers to flow. Forced convection eliminates this behavior, stabilizing the 2.25-min layer time print. These findings motivated development of a less exothermic material system, which was used to print a large-scale mold and demonstrate the value of this understanding. By presenting these challenges of large-scale reactive thermoset AM for the first time, this work motivates focused studies of the complex interplay between rheological, thermal, and chemical behaviors to improve the feasibility of large-scale thermoset AM. Tensile properties of the printed material were also measured. Longitudinal and transverse elastic moduli are 3.79 and 2.95 GPa, respectively, and corresponding tensile strengths are 36.11 and 18.83 MPa. The glass transition temperature is 93.13 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effects of soybean 7S protein on the quality and digestibility of dry rice noodles under twin‐screw extrusion process

Summary Starch and protein are important components of food, the mixed system formed between them (complexes, gels, mixtures, etc.) can improve the physical and chemical properties of starch and protein, and its potential application in the food industry has also attracted widespread attention. In this study, indica rice flour and soybean 7S protein (β‐Conglycinin) were used as the experimental materials to explore the effect of soybean 7S protein addition on the quality and digestibility of rice noodles. Aims to develop rice noodles with high protein and low GI, so that people can take care of their health while satisfying their appetites. The results showed that with the increase of soybean 7S protein addition, the starch digestibility decreased, resulting in the estimated glycaemic index (eGI) and glycaemic load (GL) decreasing. However, the cooking loss rate and breakage rate of rice noodles gradually increased, the water absorption first increased and then decreased, and the taste of rice noodles is acceptable when the 7S protein addition amount is within 9%. The interaction between starch and soybean 7S protein was mediated by weak interactions such as hydrogen bonds and hydrophobic forces indicated by Fourier transform infrared spectroscopy (FTIR) and X‐ray diffraction (XRD).

Qiao, Fan↗