Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “emission rates”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

In-Use Passenger Vessel Emission Rates of Black Carbon and Nitrogen Oxides

This study quantified emission factors of black carbon (BC) and nitrogen oxides (NO x ) from 21 engines on in-use excursion vessels and ferries operating in California's San Francisco Bay, including EPA uncertified and Tier 1-4 engines and across engine operating modes. On average, ~60 fuel-based emission factors per engine were measured using a novel combination of exhaust plume capture combined with GPS location and speed data that can be more readily deployed than common portable emissions measurement systems. Here, BC and NO x emission factors (g kg -1 ) were lowest and least variable during fast cruising and highest during maneuvering and docked operation. Selective catalytic reduction (SCR) reduced NO x emissions by ~80% when functional. However, elevated NO x emissions that exceeded corresponding exhaust standards were measured on most Tier 3 and Tier 4 engines sampled, which can be attributed to inactive SCR during frequent low engine load operation. In contrast, BC emissions exceeded the PM emission standard for only one engine, and SCR systems employed as a NO x reduction technology also reduced emitted BC. Using these measured emission factors to compare commuting options, we show that the CO 2 -equivalent emissions per passenger-kilometer are comparable when commuting by car and ferry, but BC and NO x emissions can be several to more than ten times larger when commuting by ferry.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Summertime methane and carbon dioxide emission rates and associated variables from a national‐scale survey of 146 reservoirs in the United States

Reservoirs are globally important sources of greenhouse gases, but the magnitude of their emissions is highly uncertain. Here, we present data for 146 reservoirs from two surveys of reservoir methane and carbon dioxide emissions, one at the regional scale in the midwestern United States and one at the national scale in the United States, plus data from two hand‐picked sites in Washington and Puerto Rico. At all reservoirs, ebullitive and diffusive emissions and basic physicochemistry were measured at 15–55 locations during one 22 to 64‐h period during the summers of 2016–2023, with four reservoirs revisited a second time. Contemporaneous water chemistry measurements were made at one or two locations in each reservoir. The dataset consists of two geospatial files and seven CSV files containing greenhouse gas emissions, water chemistry, morphology, and other relevant data. To date, these data comprise the largest multi‐reservoir emissions dataset assembled using consistent measurement methods.

Beaulieu, Jake J. [US Environmental Protection Age↗
DOE OSTI2026

Summertime methane and carbon dioxide emission rates and associated variables from a national-scale survey of 146 reservoirs in the United States, 2016-2023

Reservoirs are globally important sources of greenhouse gases, but the magnitude of their emissions is highly uncertain. Here we present data for 146 reservoirs from two surveys of reservoir methane and carbon dioxide emissions, one at the regional scale in the midwestern United States and one at the national scale in the conterminous United States, plus data from one reservoir in Washington and another in Puerto Rico. At all reservoirs, ebullitive and diffusive emissions and basic physiochemistry were measured at 15-70 locations during one 22 to 64-hour period during the summers of 2016-2023, with four reservoirs revisited a second time. Concomitant water chemistry measurements were also made at an index site. The dataset is comprised of two geospatial files and seven .csv files containing greenhouse gas emissions, water chemistry, morphology, and other relevant data. These data comprise the largest multi-reservoir emissions dataset ever assembled using consistent measurement methods.

Beaulieu, Jake [University of Notre Dame, IN]↗
DOE OSTI2025

Orphaned oil and gas well methane emission rates quantified using Gaussian plume inversions of ambient observations

Abstract. Annually, ∼ 3.6 million abandoned oil and gas wells in the US emit a combined ∼ 2.6 Tg methane (CH4), adversely affecting climate and regional air quality. However, these estimates depend on emission factors derived from measuring subpopulations of wells that vary by orders of magnitude due to very limited field sampling and poorly characterized distributions. Currently, US protocols to remediate orphaned wells lacks standardized quantification methods needed to both prioritize plugging and account for emission reductions. Therefore, sensitive, reliable, affordable, and scalable CH4 flux quantification methods are needed. We report the use of a simple Gaussian plume method where the dispersion parameters are constrained by in situ ground measurements of CH4 concentration at four locations 7.5–49 m downwind of the orphan well as well as local winds to estimate the leak rate from an orphan well. We derive a flux of 10.53 ± 1.16 kg CH4 h−1 during a venting procedure in April 2023 that agrees with the directly measured volumetric flow rate of 9.00 ± 0.25 kg CH4 h−1. This is 71 % greater than the 5.3 kg CH4 h−1 flux measured 7 months prior. Additionally, we discovered a secondary leak through the surface casing inferred as 0.43–0.67 kg CH4 h−1 both by our ground Gaussian analysis and by transecting the plume with an uncrewed aerial system (UAS). We show that in situ determination of the dispersion parameters used in our Gaussian inversions allows us to measure methane emissions to 15 % accuracy, significantly reducing errors when compared to the standard practice of assuming stability class. Our results help develop simpler methods and protocols for robust orphan well emission quantification that can be used for reporting.

Follansbee, Emily↗
DOE OSTI2020

Long-Term Methane Emissions Rate Quantification and Alert System for Natural Gas Storage Wells and Fields

The Department of Energy (DOE) National Energy Technology Laboratory (NETL) and other critical stakeholders (e.g., U.S. Environmental Protection Agency (USEPA), state regulators, and industry) seek to more accurately characterize and quantify methane emissions from natural gas storage wells. These efforts will reduce uncertainties in estimates of these emissions in USEPA’s current Green House Gas Inventory (GHGI) under their Greenhouse Gas Reporting Program (GHGRP; EPA, 2016). Emission factors currently used to estimate methane emissions from gas storage wells are the same factors used for onshore natural gas production wells (USEPA, 2016). This study has developed a robust and representative dataset of emissions from disaggregated gas station wellhead components and related emission factors that will inform future enhancements to the GHGI and GHGRP. Extensive methane emissions measurements and meteorological data were collected from three active storage facilities representing two of the three types of storage facilities (i.e., depleted gas reservoir and salt cavern) to support development of emissions factors specifically for gas storage wells and associated components. Methane emissions were quantified from both above-ground components (e.g., pipe fittings and valves) and seepage from the ground surface in proximity to gas storage wellheads.

03 NATURAL GAS↗
DOE OSTI2021

Atomic Iron and Nickel in the Coma of C/1996 B2 (Hyakutake): Production Rates, Emission Mechanisms, and Possible Parents

Abstract Two papers recently reported the detection of gaseous nickel and iron in the comae of over 20 comets from observations collected over two decades, including interstellar comet 2I/Borisov. To evaluate the state of the laboratory data in support of these identifications, we reanalyzed archived spectra of comet C/1996 B2 (Hyakutake), one of the nearest and brightest comets of the past century, using a combined experimental and computational approach. We developed a new, many-level fluorescence model that indicates that the fluorescence emissions of Fe I and Ni I vary greatly with heliocentric velocity. Combining this model with laboratory spectra of an Fe-Ni plasma, we identified 22 lines of Fe I and 14 lines of Ni I in the spectrum of Hyakutake. Using Haser models, we estimate the nickel and iron production rates as Q Ni = (2.6–4.1) × 10 22 s −1 and Q Fe = (0.4–2.8) × 10 23 s −1 . From derived column densities, the Ni/Fe abundance ratio log 10 [Ni/Fe] = −0.15 ± 0.07 deviates significantly from solar abundance ratios, and it is consistent with the ratios observed in solar system comets. Possible production and emission mechanisms are analyzed in the context of existing laboratory measurements. Based on the observed spatial distributions, excellent fluorescence model agreement, and Ni/Fe ratio, our findings support an origin consisting of a short-lived unknown parent followed by fluorescence emission. Our models suggest that the strong heliocentric velocity dependence of the fluorescence efficiencies can provide a meaningful test of the physical process responsible for the Fe I and Ni I emission.

Bromley, S. J. (ORCID:0000000321108152)↗
DOE OSTI2020

Applications of HPGe-detected high energy gamma rays toward quantifying neutron emission rates and 234 U enrichment in UF 6 cylinders

This study presents a 234 U enrichment meter that uses high energy gamma and neutron count rate as measured by a portable, high-purity germanium gamma ray detector. Twenty-one 30B cylinders containing UF 6 of varying origin were analyzed with an HPGe detector for high-energy gamma ray and neutron counts. Excellent correlations (R 2 0.95) between various regions of 3.0 MeV gamma rays, neutron count rate, and uranium enrichment were found. These neutron and high-energy gamma data are used to create calibration-dependent enrichment meters for 234 U. The 234 U enrichment calculated from the neutron count rate and 4 – 6 MeV gamma count rate is more accurate than methods that rely on the 120.9 keV peak which is strongly attenuated inside commercial sized UF 6 cylinders. These neutron and high-energy gamma enrichment calculators can also be used to determine a 235 U enrichment, assuming mass-based enrichment from natural uranium, but the results are not as accurate as the traditional 185.7 keV peak enrichment meter.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Quantification of oil and gas methane emissions in the Delaware and Marcellus basins using a network of continuous tower-based measurements

Abstract. According to the United States Environmental Protection Agency (US EPA), emissions from oil and gas infrastructure contribute 30 % of all anthropogenic methane (CH4) emissions in the US. Studies in the last decade have shown emissions from this sector to be substantially larger than bottom-up assessments, including the EPA inventory, highlighting both the increased importance of methane emissions from the oil and gas sector in terms of their overall climatological impact and the need for independent monitoring of these emissions. In this study we present continuous monitoring of regional methane emissions from two oil and gas basins using tower-based observing networks. Continuous methane measurements were taken at four tower sites in the northeastern Marcellus basin from May 2015 through December 2016 and five tower sites in the Delaware basin in the western Permian from March 2020 through April 2022. These measurements, an atmospheric transport model, and prior emission fields are combined using an atmospheric inversion to estimate monthly methane emissions in the two regions. This study finds the mean overall emission rate from the Delaware basin during the measurement period to be 146–210 Mg CH4 h−1 (energy-normalized loss rate of 1.1 %–1.5 %, gas-normalized rate of 2.5 %–3.5 %). Strong temporal variability in the emissions was present, with the lowest emission rates occurring during the onset of the COVID-19 pandemic. Additionally, a synthetic model–data experiment performed using the Delaware tower network shows that the presence of intermittent sources is not a significant source of uncertainty in monthly quantification of the mean emission rate. In the Marcellus, this study finds the overall mean emission rate to be 19–28 Mg CH4 h−1 (gas-normalized loss rate of 0.30 %–0.45 %), with relative consistency in the emission rate over time. These totals align with aircraft top-down estimates from the same time periods. In both basins, the tower network was able to constrain monthly flux estimates within ±20 % uncertainty in the Delaware and ±24 % uncertainty in the Marcellus. The results from this study demonstrate the ability to monitor emissions continuously and detect changes in the emissions field, even in a basin with relatively low emissions and complex background conditions.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Point Sensor Networks Struggle to Detect and Quantify Short Controlled Releases at Oil and Gas Sites

This study evaluated multiple commercially available continuous monitoring (CM) point sensor network (PSN) solutions under single-blind controlled release testing conducted at operational upstream and midstream oil and natural gas (O&G) sites. During releases, PSNs reported site-level emission rate estimates of 0 kg/h between 38 and 86% of the time. When non-zero site-level emission rate estimates were provided, no linear correlation between the release rate and the reported emission rate estimate was observed. The average, aggregated across all PSN solutions during releases, shows 5% of the mixing ratio readings at downwind sensors were greater than the site’s baseline plus two standard deviations. Four of seven total PSN solutions tested during this field campaign provided site-level emission rate estimates with the site average relative error ranging from −100% to 24% for solution D, −100% to −43% for solution E, −25% for solution F (solution F was only at one site), and −99% to 430% for solution G, with an overall average of −29% across all sites and solutions. Of all the individual site-level emission rate estimates, only 11% were within ±2.5 kg/h of the study team’s best estimate of site-level emissions at the time of the releases.

42 ENGINEERING↗
DOE OSTI2024

Neutron star cooling with lepton-flavor-violating axions

The cores of dense stars are a powerful laboratory for studying feebly coupled particles such as axions. Some of the strongest constraints on axionlike particles and their couplings to ordinary matter derive from considerations of stellar axion emission. In this work we study the radiation of axionlike particles from degenerate neutron star matter via a lepton-flavor-violating coupling that leads to muon-electron conversion when an axion is emitted. We calculate the axion emission rate per unit volume (emissivity) and by comparing with the rate of neutrino emission, we infer upper limits on the lepton-flavor-violating coupling that are at the level of | g a e μ | ≲ 10 − 6 . For the hotter environment of a supernova, such as SN 1987A, the axion emission rate is enhanced and the limit is stronger, at the level of | g a e μ | ≲ 10 − 11 , competitive with laboratory limits. Interestingly, our derivation of the axion emissivity reveals that axion emission via the lepton-flavor-violating coupling is suppressed relative to the familiar lepton-flavor-preserving channels by the square of the plasma temperature to muon mass ratio, which is responsible for the relatively weaker limits. Published by the American Physical Society 2024

Astronomy & Astrophysics↗
DOE OSTI2024

Assessing the design of integrated methane sensing networks

Abstract While methane is the second largest contributor to global warming after carbon dioxide, it has a larger warming effect over a much shorter lifetime. Despite accelerated technological efforts to radically reduce global carbon dioxide emissions, rapid reductions in methane emissions are needed to limit near-term warming. Being primarily emitted as a byproduct from agricultural activities and energy extraction, methane is currently monitored via bottom–up (i.e. activity level) or top–down (via airborne or satellite retrievals) approaches. However, significant methane leaks remain undetected and emission rates are challenging to characterize with current monitoring frameworks. In this paper, we study the design of a layered monitoring approach that combines bottom–up and top–down approaches as an integrated sensing network. By recognizing that varying meteorological conditions and emission rates impact the efficacy of bottom–up monitoring, we develop a probabilistic approach to optimal sensor placement in its bottom–up network. Subsequently, we derive an inverse Bayesian framework to quantify the improvement that a design-optimized integrated framework has on emission-rate quantifications and their uncertainties. We find that under realistic meteorological conditions, the overall error in estimating the true emission rates is approximately 1.3 times higher, with their uncertainties being approximately 2.4 times higher, when using a randomized network over an optimized network, highlighting the importance of optimizing the design of integrated methane sensing networks. Further, we find that optimized networks can improve scenario coverage fractions by more than a factor of 2 over experimentally-studied networks, and identify a budget threshold beyond which the rate of optimized-network coverage improvement exhibits diminishing returns, suggesting that strategic sensor placement is also crucial for maximizing network efficiency.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Isotopic mass effects of tritium-fueled high-performance TFTR supershots

An increase in total stored energy correlated with the addition of tritium fuel was observed in supershots during the TFTR DT campaign. This supershot regime had strikingly high, centrally peaked ion and electron temperatures, and the largest neutron emission rates observed in TFTR. This paper presents a study of the causes of this increase in stored energy in supershots. Twenty-six supershots have been recently reanalyzed with the TRANSP plasma analysis code. Early TRANSP simulations did not accurately match the measured magnitude and time evolutions of the neutron emission rates. This mismatch is attributed to neglecting apparent increases of trace amounts of heavy impurities during neutral beam injection. The new TRANSP runs were tuned to accommodate this and match the measured global neutron emission rates. These new runs also had improved fidelity in predicting the time histories and radial dependencies of measured DT neutron emission rates. That in turn adds confidence in the simulated thermal deuterium and tritium density profiles that are needed for calculating the average hydrogenic atomic mass profiles. Six subsets of these supershots had well matched toroidal field B tor , plasma current I p , flux geometry, and total injected neutral beam power. The mix of D and T beam ions was varied for different discharges. The magnitude of the increase of the thermal ion energy W i with added tritium was relatively small, and the total W tot increase is dominated by the increase in fast beam ions with T. Analyses at times before the occurrences of deleterious MHD instabilities yielded scaling of W tot with the volume-average isotopic mass consistent with previous publications. The relative fraction of fast energy ions is expected to be small in practical tokamak reactors. Thus the increase in stored energy W tot observed in TFTR supershots does not appear likely to be significantly helpful for producing useful fusion energy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Results of the 2018 Wood Stove Design Challenge

The 2018 Wood Stove Design Challenge was an international design competition which sought to identify top performing residential wood stoves based on automation. To prepare for the event, the Northeast States for Coordinated Air Use Management (NESCAUM) developed a testing protocol that challenged the stoves by testing them in more field-like conditions—capturing emissions from start-up, reloading a stove, and the use of larger piece sizes. Flue gas emissions were measured using a combination of in-stack and novel dilution sampling methods, as the event occurred on the National Mall in Washington D.C. in a non-laboratory setting. Particulate matter (PM), carbon monoxide (CO), carbon dioxide (CO2), and methane (CH4) were measured from three stoves in real-time. A combustion efficiency was also calculated for each stove in real-time. Measured PM emission rates ranged between 1.8 and 8.0 g/hr for all stoves and operating conditions, with the highest emissions being measured during cold start in all cases. The test average PM emission rates were 2.4, 4.0, and 2.4 g/hr for stoves A, B, and C, respectively. Results showed emissions measured during transient operations, which are often excluded in current certification methods, can be significantly higher than steady-state periods—echoing other studies and highlighting the importance of testing in various operational modes for more realistic emission estimates. Additionally, the stoves had overall CO emission rates of 48.8, 284.8, and 100.8 g/hr, for stoves A, B and C, respectively. Calculated PM and CO emission factors overall were low considering the testing protocol sought to follow more challenging yet realistic practices in terms of fuel loading and operating procedures. The overall estimated combustion efficiency for stoves A, B, and C was 85%, 78%, 76%, respectively and in all cases was lowest during the cold start period.This report details the successfully proposed and assembled instrumentation that was relatively portable for field-site testing and the results of the emissions measurements for the 2018 Wood Stove Design Challenge competition. Overall, the repeatability of each stove was favorable with coefficients of variation (COV) ranging from 7 to 15% for measured PM concentrations.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Regional trends and drivers of the global methane budget

Abstract The ongoing development of the Global Carbon Project (GCP) global methane (CH 4 ) budget shows a continuation of increasing CH 4 emissions and CH 4 accumulation in the atmosphere during 2000–2017. Here, we decompose the global budget into 19 regions (18 land and 1 oceanic) and five key source sectors to spatially attribute the observed global trends. A comparison of top‐down (TD) (atmospheric and transport model‐based) and bottom‐up (BU) (inventory‐ and process model‐based) CH 4 emission estimates demonstrates robust temporal trends with CH 4 emissions increasing in 16 of the 19 regions. Five regions—China, Southeast Asia, USA, South Asia, and Brazil—account for >40% of the global total emissions (their anthropogenic and natural sources together totaling >270 Tg CH 4 yr −1 in 2008–2017). Two of these regions, China and South Asia, emit predominantly anthropogenic emissions (>75%) and together emit more than 25% of global anthropogenic emissions. China and the Middle East show the largest increases in total emission rates over the 2000 to 2017 period with regional emissions increasing by >20%. In contrast, Europe and Korea and Japan show a steady decline in CH 4 emission rates, with total emissions decreasing by ~10% between 2000 and 2017. Coal mining, waste (predominantly solid waste disposal) and livestock (especially enteric fermentation) are dominant drivers of observed emissions increases while declines appear driven by a combination of waste and fossil emission reductions. As such, together these sectors present the greatest risks of further increasing the atmospheric CH 4 burden and the greatest opportunities for greenhouse gas abatement.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Smelly-Odor Webtool (Smelly) v1

Smelly is an interactive webtool displaying odor dispersion from various potential waste-to-energy sites across California. It currently displays data for dry anaerobic digestion technology with organic waste intake of 90,000 tons per year. The model addresses meteorological and geographical differences in offsite odor impacts (Jin et al. 2019). In addition to interactive display of odor dispersions, the embedded emission calculator provides two additional functionalities: (1) determine the impact distance for given onsite odor emission rates; and (2) determine allowable odor emission rates at given separation distance between the facility and its downwind communities. Please note that data and model is preliminary at this point and serve as a Proof of Concept. Additional data collection, modeling and research is needed for final application.

Jin, Ling↗