Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electron irradiation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Enhancement of the Curie temperature in single-crystalline ferromagnetic LaCrGe 3 by electron irradiation-induced disorder

LaCrGe 3 has attracted attention as a potential candidate for studies of quantum phase transitions in a ferromagnetic material. The application of pressure avoids a quantum critical point by developing a new magnetic phase. It was suggested that the disorder may provide an alternative route to a quantum critical point. We used low-temperature 2.5 MeV electron irradiation to induce relatively small amounts of pointlike disorder in single crystals of LaCrGe 3 . Irradiation leads to an increase of the resistivity at all temperatures with some deviation from the Matthiessen rule. Hall effect measurements show that electron irradiation does not cause any detectable change in the carrier density. Unexpectedly, the Curie temperature, T FM , increases with the increase of disorder from approximately 90 K in pristine samples up to nearly 100 K in the heavily irradiated sample, with a tendency towards saturation at higher doses. This effect is observed both in resistivity and magnetization measurements. Although the mechanism of this effect is not entirely clear, we conclude that it cannot be caused by effective “doping” or “pressure” due to electron irradiation. Finally, we suggest that disorder-induced broadening of a sharp peak in the density of states, D⁡(E), situated at E p = E F – 0.25 eV below the Fermi energy, E F , causes an increase in D⁡(E F ), leading to an enhancement of T FM in this itinerant ferromagnet.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Electron beam irradiation of 1,4 dioxane

Electron beam irradiation produces both, reducing and oxidizing species which facilitate the reduction of contaminants found in water and wastewater. To investigate the impact of electron beam on 1,4-dioxane, a widely used solvent which has been declared as a probable human carcinogen by the U.S. Environmental Protection Agency, a beamline was designed and commissioned at the Upgraded Injector Test Facility at Jefferson Lab. Here, wastewater samples can be irradiated with a beam energy up to 10 MeV and a beam current of up to 100 nA. Beam acceleration is achieved by two superconducting radio-frequency cavities cooled by liquid helium in a cryomodule. A beam spot with a diameter of ~5 cm was produced at the target location using a pair of raster coils. Electron beam irradiation studies were performed using 1,4-dioxane in two different matrices, de-ionized water and secondary effluent wastewater, and for two concentrations, 10 microg/L and 100 microg/L. The concentration of 1,4-dioxane after irradiation was measured as a function of dose.

Li, Xi↗
DOE OSTI2023

Development of an in situ ion irradiation scanning electron microscope

An in situ ion irradiation scanning electron microscope (I 3 SEM) has been developed, installed, and integrated into the Ion Beam Laboratory at Sandia National Laboratories. The I 3 SEM facility combines a field emission, variable pressure, scanning electron microscope, a 6 MV tandem accelerator, high flux low energy ion source, an 808 nm-wavelength laser, and multiple stages to control the thermal and mechanical state of the sample observed. The facility advances real-time understanding of materials evolution under combined environments at the mesoscale. As highlighted in multiple examples, this unique combination of tools is optimized for studying mesoscale material response in overlapping extreme environments, allowing for simultaneous ion irradiation, implantation, laser bombardment, conductive heating, cooling, and mechanical deformation.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Edge-Mediated Annihilation of Vacancy Clusters in Monolayer Molybdenum Diselenide (MoSe 2 ) under Electron Beam Irradiation

Here annihilation of vacancy clusters in monolayer molybdenum diselenide (MoSe2) under electron beam irradiation is reported. In situ high-resolution transmission electron microscopy observation reveals that the annihilation is achieved by diffusion of vacancies to the free edge near the vacancy clusters. Monte Carlo simulations confirm that it is energetically favorable for the vacancies to locate at the free edge. By computing the minimum energy path for the annihilation of one vacancy cluster as a case study, it is further shown that electron beam irradiation and pre-stress in the suspended MoSe2 monolayer are necessary for the vacancies to overcome the energy barriers for diffusion. The findings suggest a new mechanism of vacancy healing in 2D materials and broaden the capability of electron beam for defect engineering of 2D materials, a promising way of tuning their properties for engineering applications.

2D materials↗
DOE OSTI2024

Unraveling the Highly Plastic Behavior of ALD-Aluminum Oxide Encapsulations by Small-Scale Tensile Testing

We present a study directly measuring the electron-beam-induced plasticity of amorphous Al 2 O 3 coatings. Core–shell nanostructures are employed as small-scale model systems for two-dimensional coatings made by atomic layer deposition (ALD). Copper nanowires (NWs) are used as substrates for ALD deposition, representing a model system for interconnects commonly found in integrated circuits. Experiments are performed in situ in a transmission electron microscope (TEM) and further analyzed with electron energy loss spectroscopy (EELS). Our in situ TEM tensile experiments reveal the highly plastic behavior of the ALD shell, which withstands a maximum strain of 188%. Comparable samples under beam-off conditions show a brittle fracture, which underlines the effect of electron irradiation. The electron-beam-activated bond switching within the amorphous network enables compensation of the applied tensile strain, leading to viscous flow. By incorporating an intermediate nanocrystalline layer within the Al 2 O 3 shell, the plasticity is suppressed and brittle fracture occurs. This work directly demonstrates the tuning of mechanical properties in amorphous ALD structures through electron irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Modeling electron beam irradiation of methane

We built a chemical kinetic model for the electron beam irradiation of methane and report simulation results with dose rates ranging from 2 to 200 kGy s -1 at 298 K and 1 atm pressure. The model contains 92 species and 778 gas-phase reactions. We report the time evolution of concentrations of stable products (including H 2 , C 2 H 6 , C 3 H 8 , C 2 H 4 , C 3 H 6 , C 4 H 10 , C 2 H 2 , and C 3 H 4 ) as well as some radicals and ions. Here we discuss how yields of products depend on dose rate and how they change during the course of irradiation. To understand the processes controlling product formation, we quantify the extent to which various reactions produce and destroy major products and the key radicals and ions. Normalized sensitivity coefficients are computed for the production of stable products to gain further insight into factors controlling product yields. We were able to reduce the mechanism to 63 species and 331 reactions while incurring less than 5% error in the final concentrations of stable products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Mesoscale atomic engineering in a crystal lattice

Controlling individual atoms using lasers, ion traps and scanning probe tips has transformed our understanding of matter and enabled breakthroughs in quantum science. Extending this control into three-dimensional (3D) solids and across mesoscopic scales, however, remains a foundational challenge. Electron irradiation in electron microscopes is known to induce atomic displacements, and atomic manipulation has been proposed and demonstrated. Yet repeated and deterministic control has remained elusive. Here, in this study, we demonstrate deterministic atomic engineering in a 3D crystal, creating ordered arrangements of more than 40,000 user-defined defects within minutes across a 150 nm × 100 nm × 13 nm volume. By steering individual Cr atoms in the magnetic semiconductor CrSBr into selected interstitial sites using an electron beam directed with sub-20-pm-scale accuracy, we create vacancy–interstitial complexes. The resulting impurity array forms a mesoscale crystal embedded within the host lattice, a new form of engineered artificial matter that remains stable at room temperature and outside the microscope. By tracking Cr atom displacements, we identify conditions under which the defect structures are predictable. Our calculations suggest that these defects form correlated impurity states with intra-defect optical transitions and inter-defect kinetic and Coulomb interactions. This establishes a generalizable platform for atomic defect engineering at mesoscopic, and potentially macroscopic, scales, opening opportunities for scalable quantum technologies, including deterministic colour-centre placement, quantum simulation of many-body lattice models and atomic-scale manufacturing.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2023

Radiation Effects Model for Ultra-Thin Silicon Solar Cells

This work is focused on investigation of radiation effects in Ultra-Thin Silicon solar cells with a particular emphasis on electron irradiation. The study is motivated by the application of these solar cells, developed by Solestial, Inc., for powering space missions, including those led by NASA, the Department Of Defence (DOD), and commercial satellite missions. Our research encompasses both experimental and theoretical approaches, addressing unique challenges posed by ultra-thin solar cell technology that deviates from the traditional models. From the experimental point of view, the test structures were irradiated with 1 MeV electrons up to the fluence of 1E+15 e/cm$^{2}$. Radiation effects due to accumulated electron dose were noticed as a drop in open-circuit voltage (Voc). An analytical expression for modeling the Voc characteristic of the UT-Si cell after exposure to electron irradiation was formulated and subsequently compared with experimental data. The theoretical foundation of the proposed approach builds upon the Non-Ionising Energy Loss (NIEL) concept, a fundamental parameter in addressing radiation damage modelling and survivability predictions.

Fedoseyev, Alex↗
DOE OSTI2022

Conversion of Classical Light Emission from a Nanoparticle‐Strained WSe 2 Monolayer into Quantum Light Emission via Electron Beam Irradiation

Abstract Solid‐state single photon emitters (SPEs) within atomically thin transition metal dichalcogenides (TMDs) have recently attracted interest as scalable quantum light sources for quantum photonic technologies. Among TMDs, WSe 2 monolayers (MLs) are promising for the deterministic fabrication and engineering of SPEs using local strain fields. The ability to reliably produce isolatable SPEs in WSe 2 is currently impeded by the presence of numerous spectrally overlapping states that occur at strained locations. Here nanoparticle (NP) arrays with precisely defined positions and sizes are employed to deterministically create strain fields in WSe 2 MLs, thus enabling the systematic investigation and control of SPE formation. Using this platform, electron beam irradiation at NP‐strained locations transforms spectrally overlapped sub‐bandgap emission states into isolatable, anti‐bunched quantum emitters. The dependence of the emission spectra of WSe 2 MLs as a function of strain magnitude and exposure time to electron beam irradiation is quantified and provides insight into the mechanism for SPE production. Excitons selectively funnel through strongly coupled sub‐bandgap states introduced by electron beam irradiation, which suppresses spectrally overlapping emission pathways and leads to measurable anti‐bunched behavior. The findings provide a strategy to generate isolatable SPEs in 2D materials with a well‐defined energy range.

2D material↗
DOE OSTI2022

From ground to excited electronic state dynamics of electron and ion irradiated graphene nanomaterials

Microscopes utilizing convergent electron and ion beams are emerging as powerful tools for both imaging and manipulating two-dimensional materials with atomic resolution, allowing the ultimate limits of nanofabrication to be realized. In this chapter, we detail the use of time-dependent electronic structure theory to determine the excited state properties and reactivity of functionalized graphene nanostructures. A time-dependent density functional theory treatment of electronic excitations of materials is presented, with specific emphasis on predicting the position-dependent electronic response of two-dimensional nanomaterials to electron beams. The method is demonstrated in a study highlighting the important role that electronic excitation can play in opening reaction pathways relevant to atomically precise defect manipulation in graphene. Finally, we provide some perspective on future development directions for methods of simulating nonequilibrium electronic and vibrational dynamics induced by electron/ion beams.

Lingerfelt, David↗
DOE OSTI2023

Completion and Testing of a New High-Temperature Cell Holder to Support High Dose Rate Electron Beam Irradiations of Select Sulfur Chlorides (S2Cl2 and SOCl2) for Advanced Low Temperature Chlorination of Zirconium-based Used Nuclear Fuel Cladding

Short communication on the completion and testing of a new high-temperature cell holder to support high dose rate electron beam irradiations of select sulfur chlorides (S2Cl2 and SOCl2) for advanced low temperature chlorination of zirconium-based used nuclear fuel cladding.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2022

Beam-driven dynamics of aluminium dopants in graphene

Abstract Substituting heteroatoms into graphene can tune its properties for applications ranging from catalysis to spintronics. The further recent discovery that covalent impurities in graphene can be manipulated at atomic precision using a focused electron beam may open avenues towards sub-nanometer device architectures. However, the preparation of clean samples with a high density of dopants is still very challenging. Here, we report vacancy-mediated substitution of aluminium into laser-cleaned graphene, and without removal from our ultra-high vacuum apparatus, study their dynamics under 60 keV electron irradiation using aberration-corrected scanning transmission electron microscopy and spectroscopy. Three- and four-coordinated Al sites are identified, showing excellent agreement with ab initio predictions including binding energies and electron energy loss spectrum simulations. We show that the direct exchange of carbon and aluminium atoms predicted earlier occurs under electron irradiation, although unexpectedly it is less probable than the same process for silicon. We also observe a previously unknown nitrogen–aluminium exchange that occurs at Al–N double-dopant sites at graphene divacancies created by our plasma treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Electron beam irradiation effects on bulk metals: a comparative study of polycrystalline versus single-crystalline structures

This study investigates the effects of electron beam (e-beam) irradiation on the mechanical and structural properties of eight bulk metallic samples, comprising both polycrystalline (PC) and single-crystalline (SC) forms of Ni, Cr, V, and Ti. These metals were evaluated as potential candidates for beam exit windows in high-power (MW-class) particle accelerators. The primary objective is to identify metals capable of withstanding the conditions of high-power/MW-class e-beam accelerators and serve effectively as exit windows. Selection criteria were based on each metal’s intrinsic properties, power dissipation capability, and irradiation-induced changes in mechanical behavior, including hardness, elastic modulus, and defect density. Comprehensive characterization was conducted using field-emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM–EDS), X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), and nanoindentation, performed both before and after exposure to a ~¿66 kGy dose from a 10 MeV e-beam accelerator. Results revealed that e-beam irradiation induced hardening in PC Ni, whereas PC Ti, commonly used in beam exit windows, exhibited softening. The observed softening in PC Ti is attributed to grain coarsening, elongation, and the formation of twins and twin boundaries, in contrast to the smaller, compressed grains in the pristine (Pr) PC Ti samples, consistent with the Hall–Petch relationship. The stresses due to twinning are small and insignificant in influencing the overall hardening of the PC Ti irradiated sample when compared to the stresses due to the dislocation density. Conversely, SC Ti samples exhibited irradiation-induced hardening. The SC Ti irradiated samples developed additional irradiation-induced modifications in crystallographic texture of (100), (101), (110), (200), (112), (004), and (211) as evidenced from the XRD results, which could probably explain the hardening effect that is caused by irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effects of electron beam irradiation on CrMnV and CrMnTiV high entropy alloys: Nano-mechanical, structural, and thermodynamic perspectives

Beam exit windows are crucial components of any particle accelerator as they provide an interface between the beamline vacuum and target material at atmospheric media. For high beam power machines, special materials and designs are required to withstand high radiation and mechanical loads, while minimizing energy loss during transition and maximizing window lifetime. This research investigates the impact of electron beam exposure to bulk CrMnV and CrMnTiV high entropy alloys (HEAs) with the primary goal of identifying suitable candidate materials for the design of robust and durable exit window settings. The selection criteria include intrinsic characteristics, power dissipation, and mechanical responses. According to the thermodynamic calculations, both equiatomic CrMnV and the addition of 7% of Ti with equiatomic CrMnV yield solid-solutions phases. The structural and mechanical properties of CrMnV and CrMnTiV samples were tested using field emission scanning electron microscopy, atomic force microscopy, scanning electron microcopy with energy dispersive x-ray spectroscopy, x-ray diffraction, and nanoindentation before and after exposure to a dose of ~66 kGy from a 10 MeV e-beam accelerator. Despite exhibiting beam transmission characteristics comparable to Cr and V, the indentation hardness of HEAs exceeded that of the Cr and V samples by five to six times. The examination of the CrMnTiV irradiated samples revealed organized deformation patterns depicting new features, which we suspect twinning and twin boundaries due to the addition of Ti to CrMnV. Ti, a hexagonal-close-packed crystal structure, is commonly known for deformation twinning behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Small Scale Creep Testing of 14YWT via In-situ Transmission Electron Microscopy Irradiation and Nanoindentation

The next generation of nuclear materials must withstand harsh operating conditions such as high temperatures and irradiation doses. Nanostructured ferritic alloys like oxide dispersion strengthened steels, especially 14YWT, have shown promise as a structural material to withstand these harsh operating conditions. For application, understanding the irradiation enhanced creep of the structural components is fundamental to evaluating the service life in a reactor. Challenges with evaluating irradiation enhanced creep are related to the limited space in nuclear reactors and the expense of conducting post irradiation experiments on irradiated cladding. Ion irradiations are considered to expedite irradiation testing, but such experiments have restricted depth of penetration into the material, limiting the ability to characterize changes to material properties after irradiation. Small scale mechanical testing can be used with ion beam irradiations as a potential avenue to evaluate the irradiation enhanced creep of materials. In this study, in-situ transmission electron microscopy nanopillar creep studies on 14YWT were performed and simultaneously ion beam irradiated with 2.8 MeV Au4+ ions. It was observed that the ion beam irradiation did increase the measured strain rate of the materials. In addition, ex-situ nanoindentation creep studies were performed over a range of temperatures on control 14YWT, and it was observed that there was a change in the deformation mechanism between 873 K and 1073 K that agrees well with macro-scale mechanical testing. Furthermore, these results show promise for applying these techniques to nuclear materials in the future.

14 YWT↗
DOE OSTI2020

Mechanical detwinning device for anisotropic resistivity measurements in samples requiring dismounting for particle irradiation

Uniaxial stress is used to detwin samples of orthorhombic iron based superconductors to study their intrinsic electronic anisotropy. Here we describe the development of a new detwinning setup enabling variable-load stress-detwinning with easy sample mounting/dismounting without the need to re-solder the contacts. It enables the systematic study of the anisotropy evolution as a function of an external parameter when the sample is modified between the measurements. In our case, the external parameter is the dose of 2.5 MeV electron irradiation at low temperature. We illustrate the approach by studying resistivity anisotropy in single crystals of Ba 1-x K x Fe 2 As 2 at x =0.25 where the much discussed unusual re-entrance of tetragonal C 4 phase, C 4 → C 2 → C 4 , is observed on cooling. With the described technique we found a significant anisotropy increase in C 2 phase after electron irradiation with dose of 2.35 C/cm 2 .

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Electron beam irradiated foil expansion simulated by a coupled HYDRA/MCNP6 application

Simulating the hydrodynamic evolution of a temporally pulsed electron beam with multiple metal foils requires coupling the nearly monoenergetic, relativistic electron beam to the foil target. This deposition may be effectively calculated by Monte Carlo transport. Once this energy is deposited on a computational mesh representing the foil target, highly developed radiation-hydrodynamic codes, such as HYDRA, can describe the subsequent evolution. Currently, HYDRA does not have an internal Monte Carlo electron transport capability. To partially rectify this deficiency, a PYTHON-based scheme to link MCNP6 to HYDRA has been developed for quadrilateral meshes. Results from a seven-foil tantalum target configuration are presented to demonstrate this capability.

42 ENGINEERING↗