Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electron beam melting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Nickel-based superalloy single crystals fabricated via electron beam melting

Additive manufacturing technologies have emerged as potential disruptive processes whose possible impacts range from supply chain logistics, prototyping, and novel materials synthesis. Numerous works illustrate the ability to control mi- crostructure in fusion based processes and a few recent authors have even produced single crystals. However, a number of open questions remain regarding the process window which enables printing of single crystals. Furthermore, it has been observed that these additively manufactured single crystals exhibit a preferred $\langle$011$\rangle$ secondary orientation. In this work we investigate fabrication conditions which enable printing of single crystals via electron beam melting. A space filling design of experiments is utilized to efficiently explore the fabrication space. Single crystals were success- fully obtained using both commercially available powders and custom melt alloys. Microstructures obtained via these exploratory experiments exhibited a continuum of columnar structures ranging from weakly textured polycrystals, near single crystal, and fully single crystalline material. Complex geometry experiments are performed to study the grain selection mechanism. We find that the grain selection mechanism is independent of the bulk scale geometry and must therefore by driven by local heat transfer and solidification dynamics. Furthermore, grain selection is shown to be driven by competing driving forces; one which prefers epitaxial growth and another which is driven by the imposed scan pattern geometry. Finally, a mechanism is proposed for the anomalous secondary orientation preference.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Isothermal and Cyclic Oxidation of Haynes 282 Processed by Electron Beam Melting (EBM) and Laser Powder Bed Fusion (LPBF) in Dry Air at 800 and 950°C

Here, the isothermal and cyclic oxidation behavior of Haynes 282 (H282) processed by laser powder bed fusion and electron beam melting was compared to its cast counterpart during exposures in air at 800 and 950°C. The specific microstructure of the AM alloys compared to coarse-grain cast 282 resulted in differences in oxidation rates, internal oxidation and spallation behavior. At 800°C, faster Ti diffusion to the surface due to the smaller grain size of the AM alloys led to Ti doping of the Cr 2 O 3 scale and faster oxidation rates. The higher density of grain boundaries also resulted in more pronounced internal oxidation. At 950°C, a duplex Cr 2 O 3 scale was observed with a dense inner layer and porous cracked outer layer with embedded TiO 2 particles. The impact of the external and internal oxide compositions and oxidation-induced elemental depletions on the oxidation lifetime, creep properties and spallation behavior is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Understanding the Effect of Electron Beam Melting Scanning Strategies on the Aluminum Content and Materials State of Single Ti-6Al-4V Feedstock

Research on the additive manufacturing of metals often neglects any characterization of the composition of final parts, erroneously assuming a compositional homogeneity that matches the feedstock material. Here, the composition of electron-beam-melted Ti-6Al-4V produced through three distinct scanning strategies (linear raster and two point melting strategies, random fill and Dehoff fill) is characterized both locally and globally through energy-dispersive spectroscopy and quantitative chemical analysis. As a result of the different scanning strategies used, differing levels of preferential vaporization occur across the various parts, leading to distinct final compositions, with extremes of ~5.8 wt.% Al and ~4.8 wt.% Al. In addition, energy-dispersive spectroscopy composition maps reveal specific features in both the XY and XZ planes (with Z being the build direction) as a result of local inhomogeneous preferential vaporization. The subsequent change in composition significantly modifies the materials’ state of parts, wherein parts and local regions with higher aluminum contents lead to higher hardness levels (with a ~50 HV difference) and elastic property values and vice versa. While varying scan strategies and scan parameters are known to modify the microstructure and properties of a part, the effect on composition cannot, and should not, be neglected.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Texture evolution as a function of scan strategy and build height in electron beam melted Ti-6Al-4V

Metal additive manufacturing (AM) enables customizable, on-demand parts, allowing for new designs and improved engineering performance. Yet, the ability to control AM metal alloy microstructures (i.e., grain morphology, crystallographic texture, and phase content) is lacking. Furthermore, this work performs corroborative neutron diffraction and large-scale electron backscatter diffraction (EBSD) measurements to assess crystallographic texture in electron beam melted (EBM) Ti-6Al-4V as a function of scan strategy and build height. Texture components for one raster and two spot melt scan strategies were evaluated using a triclinic specimen symmetry to capture all possible texture components, which were found to be considerably different than previously reported values from studies employing orthotropic specimen symmetry. This finding highlights the importance of a standard method and best practice for assessing textures produced by AM.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Creep Behavior of a High-$\gamma^{\prime}$ Ni-Based Superalloy Fabricated via Electron Beam Melting

Additive manufacturing enables the fabrication of complex engineering components previously inaccessible through traditional processes. Nickel-base superalloys with large γ' volume fraction are typically considered non-weldable and therefore exhibit a propensity for cracking during the fusion process. These crack-prone materials, however, are of great importance in gas turbine engines due to their excellent high temperature creep resistance. In this study we investigate the creep behavior of IN738LC produced by the electron beam melting process. Here, we find that with appropriate post-build heat treatment the creep response of material oriented in the build direction exhibits deformation and rupture behavior comparable to that of conventionally cast IN738 & IN738LC. In the transverse direction properties fall below the expected cast behavior, however, we argue this is likely due to differences in grain scale and crystallographic texture. It may be possible to coarsen the grain morphology with appropriate process-parameter optimization in order to reduce the severity of intergranular fracture in the transverse direction. These results illustrate that high temperature properties exhibited by additively manufactured IN738LC are suitable for the hot section of gas turbine engines.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Processing of tungsten through electron beam melting

Additive manufacturing (AM) presents a new design paradigm for the manufacture of engineering materials through the layer-by-layer approach combined with welding theory. In the instance of difficult to process materials such as tungsten and other refractory metals, AM offers an opportunity for radical redesign of critical components for next-generation energy technologies including fusion. In this work, electron beam powder bed fusion (EB-PBF) is applied to process pure tungsten to study the influence of process parameters on the defect density of the material. Here, an in-situ image analysis algorithm is applied to pure tungsten for the first time, and is used to visualize the defect structure in AM tungsten. Finally, a cracking mechanism for AM tungsten is proposed, and suggestions for suppression of cracks in pure tungsten are offered.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Electron Beam Melting of Niobium Alloys from Blended Powders

Niobium-based tungsten alloys are desirable for high-temperature structural applications yet are restricted in practice by limited room-temperature ductility and fabricability. Powder bed fusion additive manufacturing is one technology that could be leveraged to process alloys with limited ductility, without the need for pre-alloying. A custom electron beam powder bed fusion machine was used to demonstrate the processability of blended Nb-1Zr, Nb-10W-1Zr-0.1C, and Nb-20W-1Zr-0.1C powders, with resulting solid optical densities of 99+%. Ultimately, post-processing heat treatments were required to increase tungsten diffusion in niobium, as well as to attain satisfactory mechanical properties.

36 MATERIALS SCIENCE↗
NASA NTRS2018

Location-Specific Microstructure and the Effect of Heat Treatment on Electron-Beam Melted Ni-Based Superalloy LSHR

Examine set-to-set variability with 4 build sets with the same layout Establish the effect of solutioning heat treatments (HT) on as-fabricated grain structure and microstructure – (gamma)’-solvus= 1156 ºC (1) As-fabricated (2) 2 hour subsolvus HT(-15 ºC) + conventional 2-step aging (3, 4, 5) 0.5 hour, 2 hours, 4 hours supersolvus HT (+18 ºC) + 2 step aging Gain insight into location-specific microstructure to correlate later to mechanical properties (tensile, creep, LCF behavior)

heat treatment↗
NASA NTRS1972

Mechanical properties of electron-beam-melted molybdenum and dilute molybdenum-rhenium alloys

A study of molybdenum and three dilute molybdenum-rhenium alloys was undertaken to determine the effects of rhenium on the low temperature ductility and other mechanical properties of molybdenum. Alloys containing 3.9, 5.9, and 7.7 atomic percent rhenium exhibited lower ductile-brittle transition temperatures than did the unalloyed molybdenum. The maximum improvement in the annealed condition was observed for molybdenum - 7.7 rhenium, which had a ductile-brittle transition temperature approximately 200 C (360 F) lower than that for unalloyed molybdenum. Rhenium additions also increased the low and high temperature tensile strengths and the high temperature creep strength of molybdenum. The mechanical behavior of dilute molybdenum-rhenium alloys is similar to that observed for dilute tungsten-rhenium alloys.

Klopp, W. D.↗
NASA NTRS1973

Mechanical properties of electron-beam-melted molybdenum and dilute Mo-Re alloys.

Study of Mo-Re alloys aimed at examining the effects of small rhenium additions on the low-temperature ductility of molybdenum and determining the mechanical properties of dilute Mo-Re alloys. The results obtained indicate that high-purity Mo-Re alloys have ductile-brittle transition temperatures considerably lower than those for unalloyed molybdenum and that rhenium promotes normal solid-solution strengthening in molybdenum at elevated temperatures.

Klopp, W. D.↗
DOE OSTI2022

SRF E - Beam Accelerator for Metal Additive Manufacturing [Patent]

A system and apparatus for electron beam melting comprises a superconducting radio frequency accelerator configured to produce an electron beam, a conduction cooling system configured to cool the superconducting radio frequency accelerator, and an electron beam melting system wherein the electron beam melts power in a build chamber of the electron beam melting apparatus.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

SRF e-beam accelerator for metal additive manufacturing

A system and apparatus for electron beam melting comprises a superconducting radio frequency accelerator configured to produce an electron beam, a conduction cooling system configured to cool the superconducting radio frequency accelerator, and an electron beam melting system wherein the electron beam melts power in a build chamber of the electron beam melting apparatus.

Thangaraj, Jayakar C.↗
DOE OSTI2023

EB Vs PAM Vs VAR for Uranium Alloys

Questions were raised during the February ’97 PDP Meeting at LLNL as to the advisability of funding three separate melting development programs (Advanced Vacuum Arc Remelt (VAR), Plasma Arc Melting (PAM) and Electron Beam Melting (EB)) through PDP in this era of shrinking research funds. The main issues seemed to be: 1) Have we evaluated the potentials of the three processes sufficiently to eliminate any of them out of hand and 2) Have any of these processes to date produced results which show clear advantages over the other two. The feeling at the meeting toward the latter seemed to be that all three processes required further development before they would be accepted by the complex as the standard. As far as evaluating potential for process improvements, however, we at Livermore did go through somewhat of a trade study in 1993 when we proposed the EB route. It seemed to us that even with the elimination of the skull caster via a VIM/VAR/VAR route, the problem of recycle limitations in the VIM step due to excessive carbon pick-up limited the potential for a great improvement in material utilization using this method. A single-step, cold hearth route looked to be the preferable choice. Both EB and PAM are used commercially as cold hearth processes, and both have been used for the production of refractory and specialty metals; EB since the mid 1950’s and PAM since the mid 1980’s. Both seem to have found their individual niches with some applications being suited to EB and others to PAM. Both can be adapted to continuous casting techniques and both are capable of imparting the high heat fluxes necessary to melt refractory metals. The major differences appear to be that for most applications, the EB process is capable of producing a purer product, while PAM results in less loss of volatile components. There exists an abundance of information in the open literature on the results of processing via both routes on various materials. The attached 1984 paper gives a good explanation of electron beam melting and plasma melting, and, I believe, a fair assessment of the advantages and limitations of both processes.

36 MATERIALS SCIENCE↗
NASA NTRS2014

Fabrication of Turbine Disk Materials by Additive Manufacturing

Precipitation-strengthened, nickel-based superalloys are widely used in the aerospace and energy industries due to their excellent environmental resistance and outstanding mechanical properties under extreme conditions. Powder-bed additive manufacturing (AM) technologies offer the potential to revolutionize the processing of superalloy turbine components by eliminating the need for extensive inventory or expensive legacy tooling. Like selective laser melting (SLM), electron beam melting (EBM) constructs three-dimensional dense components layer-by-layer by melting and solidification of atomized, pre-alloyed powder feedstock within 50-200 micron layers. While SLM has been more widely used for AM of nickel alloys like 718, EBM offers several distinct advantages, such as less retained residual stress, lower risk of contamination, and faster build rates with multiple-electron-beam configurations. These advantages are particularly attractive for turbine disks, for which excessive residual stress and contamination can shorten disk life during high-temperature operation. In this presentation, we will discuss the feasibility of fabricating disk superalloy components using EBM AM. Originally developed using powder metallurgy forging processing, disk superalloys contain a higher refractory content and precipitate volume fraction than alloy 718, thus making them more prone to thermal cracking during AM. This and other challenges to produce homogeneous builds with desired properties will be presented. In particular, the quality of lab-scale samples fabricated via a design of experiments, in which the beam current, build temperature, and beam velocity were varied, will be summarized. The relationship between processing parameters, microstructure, grain orientation, and mechanical response will be discussed.

oxidation↗
DOE OSTI2021

Solidification texture, variant selection, and phase fraction in a spot-melt electron-beam powder bed fusion processed Ti-6Al-4V

The effect of a spot melt strategy on the solidification texture, variant selection, phase fraction, and their variations along the build height was investigated in comparison to a conventional linear melt strategy. Ti-6Al-4V alloy samples were manufactured by an electron-beam powder bed fusion process using two different melt strategies and characterized using high-energy synchrotron x-ray diffraction. The linear and spot melt cases resulted in β<100> cube and fiber textures, respectively, with the cube/fiber axis nearly parallel to the build direction. The α phase exhibited Burgers orientation relationship (BOR) with the parent β phase for both melt strategies. Although all of the key texture components and the BOR between the α and β phases were consistently observed in both cases along the build height, there were several measurable differences between the two. At the top of the build height, the β<100> build texture intensity was stronger in the linear case. However, the texture intensity in the linear case decreased gradually from the top to near the substrate, whereas the spot melt case did not show this trend. Moreover, the BOR was examined along the build height and the results showed that there is a distinct variant selection in the spot melt case, unlike the linear case. Specifically, the planar variants sharing ($\bar101$) β || (0002) α with [$\bar2\bar2\bar2$]β and [$2\bar22$]β were the most prominent in the spot melt, but no preference was identified in the directional variants. The β phase fraction was slightly lower in the spot melt case compared to the linear case. In both the cases, the β phase fraction decreased moving towards the substrate but remained significantly higher than that of the powder feedstock. Overall, the novel spot melt strategy produced a more homogeneous microstructure in terms of both the phase fraction and texture across the build height.

36 MATERIALS SCIENCE↗