Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electrodialysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Separation characteristics of cations and natural organic matter in electrodialysis

Natural organic matter (NOM) in water can cause the formation of disinfection byproducts (DBPs) when NOM reacts with a disinfectant such as chlorine. Nanofiltration (NF) and reverse osmosis (RO) are effective treatment methods to remove NOM. However, the simultaneous presence of both NOM and divalent cations such as Ca 2+ can enhance fouling in NF and RO. Therefore, an appropriate pretreatment to remove such cations before NF or RO would delay fouling and perhaps improve water recovery and NOM removal efficiency. Electrodialysis (ED) is potentially an excellent pretreatment method because it separates inorganic ions well using ion exchange membranes (IEMs) but does not separate NOM well because of its size and consequent low diffusivity. This research focused on ion and NOM separation with ED using three different types of commercially available IEM pairs, two different commercially available NOM sources, and six different influents at 500 mg/L total dissolved solids in the presence or absence of both hardness (Ca 2+ and Mg 2+ ) and NOM. The target waters of interest in this research were drinking water supplies that require little or no desalination but substantial removal of NOM; after NOM separation in NF or RO, some or all of the ED concentrate can be added to the NF/RO permeate to create the finished water prior to disinfection. The results indicate that ED can effectively separate alkaline earth metal ions without separation of NOM. Cation exchange membranes with high exchange capacity, high selectivity for divalent cations are desirable, and both anion and cation exchange membranes should have low affinity for organic adsorption. As a result, the process would work particularly well for NOM with relatively low hydrophobicity, since NOM adsorption to most surfaces increases with hydrophobicity.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of electrode rinse solutions on the electrodialysis of concentrated salts

The data presented indicate that modest attention to the chemistry of the electrode rinse solution can yield as much as 56% improvement in process efficiency. When operating electrodialysis (ED) with salt concentrations greater than 10,000 mg/l (as NaCl) the amperage can be relatively high even at low voltages. To maximize the overall rate of ion transport from diluate to concentrate, there is a need to minimize resistances in the electrode cells since these can represent as much as 30% of the total resistances in the entire process and in this particular ED unit, represented resistance roughly equivalent to that within the membrane stack. This work describes the performance of a 10-cell pair, 200 cm 2 (0.02 m 2 ) per membrane, pilot ED unit operated in batch mode at 5 V potential. The feedstock to the stack was varied from 0.5% to 6% NaCl. Results from Volt-amp profiles (2.0–15 V) were used as the rationale for choosing the preferred electrode rinse solution, 90 g/l (kg/m 3 ) disodium sulfate at pH 12.5. The recommended solution of 30 g/l (kg/m 3 ) disodium sulfate at neutral pH was tested against stronger solutions (60, 90, and 120 g/l (kg/m 3 ) disodium sulfate) at neutral pH and with 1 g/l (kg/m 3 ) sodium hydroxide added to yield solutions at pH 12.5. There were stark differences in the performance of the ED unit between the solutions at pH 7 and those at pH 12.5. The slopes of the Volt-amp profiles improved indicating less resistance to ion flow at pH 12.5. Most of the difference can be attributed to the greater conductivity of sodium hydroxide compared to disodium sulfate, where even a modest addition of 1 g/l (kg/m 3 ) sodium hydroxide increased the conductivity of the solution between 8 and 20% depending on the concentration of disodium sulfate. Most notably, the initiation voltage was 2.39 ± 0.08 V with solutions at pH 7 and 1.99 V ± 0.04 V when the rinse solutions were around pH 12.5, a difference of around 0.42 V. Since the full batch runs were performed at 5.0 V, this 0.42 V differential represented a loss of 8% in process efficiency. A series of tests showed a shift in initiation voltage occurred between pH 11.5 and 12.5. Nernst equations for water electrolysis are coupled with a simple flux model that estimates the concentration of hydroxide and hydronium ions at the electrode surfaces. This model indicates that the potential demanded by the electrodes is directly linked to the current. Furthermore, there is a steep drop in the potential demanded by the anode when there is sufficient hydroxide available to generate oxygen from hydroxide as opposed to generation from water. The voltage demand is minimal at pH 12.5 and reflective of the reference standard voltage (just over 1.23 V predicted at 0.1 amps). However, the flux model predicts that the voltage demanded by the electrodes at pH 7 is 1.61 V at 0.1 amps (the lowest amperage measurable with the power pack). In conclusion, comparing this result to the reference standard (E 0 = -1.23 V) yields a satisfactory explanation for the observed difference below reference standard of 0.42 V.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Bipolar Membranes Electrodialysis for Water Purification and Resource Recovery

Reverse osmosis concentrate (ROC) from inland brackish water desalination and wastewater recycling presents moderate salinity, posing significant challenges for treatment and disposal. Existing treatment technologies predominantly rely on energy-intensive thermal methods, large-area evaporation strategies, or deep-well disposal, which often result in the loss of water value. Electrified membrane brine treatment offers a promising alternative by utilizing renewable energy sources, enabling complete water recycling. This work proposes the development of next-generation bipolar membrane electrodialysis (BMED) systems capable of desalinating brine while simultaneously recovering valuable resources. However, several critical challenges remain in the areas of membrane engineering for BMED. These include: 1) decreased current efficiency during desalination due to the low conductivity of feed chambers, 2) fouling and scaling from multivalent ions and contaminants in the feed, and 3) the retention and carryover of ROC contaminants, including PFAS compounds. Our research focuses on the development of novel anion exchange membranes (AEMs) and cation exchange membranes (CEMs) based on synthesized multiblock copolymers. We investigate the effects of block length, ion exchange capacity (IEC), and polymer backbone structure on cation and anion transport (e.g., Na+, Cl-, OH-, H+) for both our synthesized membranes and commercial membranes. Fundamental properties of these membranes, such as water uptake, IEC, and ionic conductivity, are also evaluated to optimize performance for BMED applications.

08 HYDROGEN↗
DOE OSTI2024

An integrated approach to optimizing concentration shock wave electrodialysis using 2D multicell simulation and response surface models

Shock wave electrodialysis (SWED) is a highly promising technique for energy-efficient ion separation in the context of a circular economy. This paper presents a approach way of modeling and improving SWED using a two-dimensional multicell model combined with the COMSOL program and response surface methodology. The model integrates the Nernst-Planck equation, Darcy's law, and first-order electroosmosis to examine the local concentration, flux of ionic species, distribution of current, and velocity of flow in SWED cells under various operating conditions. We first illustrate the clear depiction of concentration, velocity, and electric potential distribution through contours which aids in identifying optimal operating conditions and designing scalable SWED systems. The results emphasize the significance of surface charge density and voltage in influencing the features of shock waves for obtaining effective ion separation while optimizing energy consumption and improving current efficiency by controlling the retention time of feed flow. Here, this study defines two crucial characteristics of shock waves, namely the length of the flat depletion zone of a fully developed shock wave (shock wave height) and the distance of shock wave propagation (shock wave length). These properties significantly impact separation performance, as determined by the simulation results. Additionally, the response surface methodology is incorporated with the COMSOL models to develop predictive models and graph responses, enabling a more comprehensive understanding of the interactions between parameters and performance indicators, such as removal ratio, energy consumption, and water recovery. Finally, this work suggests design tactics for expanding SWED processes and outlines potential areas for further research. This research provides valuable insights into the prospective applications, design optimization, and scalability of SWED in the field of electrokinetic separation technologies for green chemistry and a circular economy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Application of electrodialysis pretreatment to enhance boron removal and reduce fouling during desalination by nanofiltration/reverse osmosis

we report membranes have emerged as promising technologies for treatment of non-traditional waters, but fouling and poor rejection of small, neutral solutes (e.g., boric acid) impede their further implementation for water purification. Boron rejection is increased by raising the pH to convert boric acid to borate ion, but this change often leads to calcite supersaturation. This study investigated the use of a hybrid electrodialysis-nanofiltration/reverse osmosis (ED-NF/RO) system to reduce fouling from calcite precipitation and calcium-polysaccharide sorption to NF/RO membranes. Also, the study examined the potential of the hybrid process to increase permeate flux and boron rejection during NF/RO of synthetic saline water. ED pretreatment reduced calcite oversaturation and reduced flux decline during NF/RO. Low alginate concentrations (25 mg/L) limited NF/RO fouling, but high concentrations (100 mg/L) appeared to promote calcite scaling. ED pretreatment reduced the osmotic pressure of the NF/RO feed water, enabling lower operating pressures or greater permeate water fluxes. Boron rejection during NF/RO increased with ED pretreatment, probably due to stronger electrostatic repulsion and an increase in the fraction of total boron present as B(OH)4- following ED. This hybrid ED-NF/RO system shows promise as a novel approach to enhancing the performance of current membrane systems for treating complex feed waters.

alginate↗
DOE OSTI2024

Electrodialysis and nitrate reduction (EDNR) to enable distributed ammonia manufacturing from wastewaters

Underutilized wastewaters containing dilute levels of reactive nitrogen (Nr) can help rebalance the nitrogen cycle. This study describes electrodialysis and nitrate reduction (EDNR), a reactive electrochemical separation architecture that combines catalysis and separations to remediate nitrate and ammonium-polluted wastewaters while recovering ammonia. By engineering operating parameters (e.g., background electrolyte, applied potential, electrolyte flow rate), we achieved high recovery and conversion of Nr in both simulated and real wastewaters. The EDNR process demonstrated long-term robustness and up-concentration that recovered >100 mM ammonium fertilizer solution from agricultural runoff that contained 8.2 mM Nr. EDNR is the first reported process to our knowledge that remediates dilute real wastewater and recovers ammonia from multiple Nr pollutants, with an energy consumption (245 MJ per kg NH 3 –N in simulated wastewater, 920 MJ per kg NH 3 –N in agricultural runoff) on par with the state-of-the-art. Demonstrated first at proof-of-concept and engineered to technology readiness level (TRL) 4–5, EDNR shows great promise for distributed wastewater treatment and sustainable ammonia manufacturing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2003

Removal of sodium chloride from human urine via batch recirculation electrodialysis at constant applied voltage

The removal of sodium chloride (NaCl) from human urine using a six-compartment electrodialysis cell with batch recirculation mode of operation for use in advanced life support systems (ALSS) was studied. From the results obtained, batch recirculation at constant applied voltage yields high values (approximately 94% of NaCl removal. Based on the results, the initial rate of NaCl removal was correlated to a power function of the applied voltage: -r=2.0 x 10(-4)E(3.8). With impedance spectroscopy methods, it was also found that the anion membranes were more affected by fouling with an increase of the ohmic resistance of almost 11% compared with 7.4% for the cationic ones.

Ecological Systems, Closed↗
NASA NTRS2019

Waste Water Brine Purification through Electrodialysis Ion Exchange

Reutilizing resources onboard the International Space Station (ISS) and for future deep space missions are critical for mission longevity and sustainability. Waste water brine produced from water recovery systems contain chemical species that could be processed into a potential fertilizer for future plant systems.Fertilizer production can be achieved through a process called electrodialysis ion exchange. Waste water containing inorganic salt components are fed through a series of ion exchange membranes to produce fertilizer (a phosphate rich stream), electrolysis-grade water, and other useful commodities.A test bed was constructed to conduct controlled experiments and an experimental design procedure developed to determine the feasibility of the process. Conductivity and pH probes were utilized to determine the ion concentration in each of the product streams, along with ion chromatography (IC) to define the exact concentration of each ion in every stream throughout the experiment. This is crucial in order to convey the effectiveness of ion removal from the incoming waste water stream.The waste water and electrolyte streams were prepared in the lab prior to experimentation. Additionally, the ion exchange membrane configurations were developed and Opto 22 data analysis software incorporated to conduct measurements in real time.Ions successfully diffused across their respective membranes into the concentrate, acid, and base streams. This resulted in pure water, a phosphate rich stream, and a separate anion/hydrogen and cation/hydroxide stream.

Hancock, Matthew L.↗
DOE OSTI2020

Studies on the Encapsulation of Brine Generated from a Process Using Selective Electrodialysis Reversal

This topical report summarizes the laboratory testing, geochemical modeling, and mineralogical testing conducted to examine the efficacy of wastewater encapsulation for the brine generated from the Saltworks Flex electrodialysis reversal technology. Within the laboratory testing, the short- and long-term physical properties of seven separate mix designs were examined along with the leaching of each mix design. Additionally, geochemical thermodynamic modeling was used along with mineralogical analyses to help gain a fundamental understanding of the chemistry involved in the encapsulation process. Encapsulation is a process that results in the immobilization of constituents of interest by creating an engineered material that contains the waste within its matrix, both physically and chemically, in such a manner that the receiving environment is protected from adverse effects. Within the context of this study, encapsulation mix designs involved mixing the Saltworks brine with fly ash and various additives, principally lime (calcium oxide) and cement, to form a paste that eventually sets and hardens into a monolith upon placement in a landfill. Moisture conditioning fly ash with wastewater sources for on-site landfill disposal is a process that is in use at some sites and has been presented as a viable option to dispose of liquid wastes. However, because chemical reactions that can lead to sequestration of constituents of interest are not optimized, leaching can occur. Therefore, in this study, mixes were created to mimic moisture conditioning, as well as engineered pastes of varying mix designs. The study found that engineered encapsulation mixes provide significant resistance to leaching compared to moisture conditioning alone. The best performing encapsulation mix used lime as the additive, which proved superior to the use of cement. After 90 days of curing, this encapsulated mix was 5.5 times stronger than the moisture conditioned mix. Additionally, this mix exhibited an approximate 2.5 order of magnitude drop in hydraulic conductivity compared to the moisture conditioned mix. When comparing leaching, nearly all the chloride was found to evolve from the moisture conditioned mix, whereas only 6.7% of the chlorine contained in the best performing encapsulated mix leached out. Mineralogical analysis via X-ray diffraction (XRD) showed a significant concentration of the chloride sequestering mineral, Friedel’s salt, in the best performing encapsulation mix, whereas none was observed in the moisture conditioned mix, pointing to it being the primary chemical mechanism for chloride retention, along with the physical impermeability of the material. With respect to the modeling study, the model was successful in predicting the presence of most mineral phases observed in the XRD analysis.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Selective Removal of Barium and Hardness Ions from Brackish Water with Chemically Enhanced Electrodialysis

The use of a nonconventional water resource for energy and industrial applications often requires extraction of low-level undesirable ions from matrices of benign dominant ions. In this study, the selective extraction of Ba 2+ and Mg 2+ from synthetic brine solutions was evaluated using strong acid cation-exchange membranes modified with the surface deposition of macrocyclic molecules including crown ethers and calixarenes. Compared to the bare membrane, vinylbenzo-18-crown-6 (VB18C6) and calix[4]arene-amended membranes showed increased selectivity for Ba 2+ and Mg 2+ with respect to the dominant ion (Na + ) by up to fourfolds, with the calix[4]arene-modified membrane achieving more selective separation than VB18C6. Optimal selectivity was achieved at a moderate-to-high current density (3.1–6.3 mA/cm 2 ), which was attributed to the alleviation of transport limitation in the boundary layer by the surface modification. Amendment of a calix[4]arene derivative with a crown-6 “boot strap” and two carboxylic groups resulted in reduced selectivity due to the formation of strong complexes with divalent ions. Furthermore, these results show that surface deposition of ion sequestrants can be a versatile approach to improve the membrane’s selectivity; however, the performance is sensitive to feed water salinity, current loading, and the macrocycle-ion chemistry, where there is a trade-off between ion affinity and mobility.

36 MATERIALS SCIENCE↗