Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “eddy current loss”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Magnetic bearings for a spaceflight optical disk recorder

The development and testing of a magnetic bearing system for the translator of the read/write head in a magneto-optic disk drive are discussed. The asymmetrical three-pole actuators with permanent magnet bias support the optical head, and its tracking and focusing servos, through their radial excursion above the disk. The specifications for the magnetic bearing are presented, along with the configuration of the magnetic hardware. Development of a five degree of freedom collision model is examined which allowed assessment of the system response during large scale transients. Experimental findings and the results of performance testing are presented, including the roll-off of current-to-force due to eddy current loss in the magnetic materials.

Hockney, Richard↗
NASA NTRS2023

Magnetic Anisotropy and Stress Dependent Epoxy Wetting in FeNi-based Metal Amorphous Nanocomposite

Recently developed FeNi-based metal amorphous nanocomposites (MANCs) used in high-speed motors (HSMs) exhibit reduced eddy current losses while maintaining good mechanical properties and glass-forming abilities. Magnetic anisotropy in (Fe 70 Ni 30 ) 80 Nb 4 B 14 Si 2 amorphous magnetic ribbon (AMR) in the as-cast state and upon conventional (T CA ) and strain (T SA ) annealing heat treatment is investigated. From ribbon samples in as-cast condition, quenched in stress from planar flow casting (PFC) induced as-cast curvature derived uniaxial magnetic anisotropy. Stress relief by conventional furnace annealing at T CA > 350 °C achieved isotropic properties in the bulk. Annealing about the primary crystallization temperature, T CA ~ 450 °C, resulted in the formation of both FCC and BCC nanocrystallites and evolution to isotropic bulk magnetic properties confirming the random anisotropy model. In samples strain annealed at T SA = 440 °C at various tensions, relatively large controlled induced uniaxial anisotropy is achieved. The largest magnetic anisotropy occurs in annealing under the stress of 250 MPa yielding an anisotropy field of 7.1 x 10 4 A/m. Surface anisotropy observed by MOKE differs from bulk anisotropy due to image contrast from closure domains. Epoxy coatings are important for improved bonding, mechanical properties, and resistivity in tape-wound MANC cores for HSMs. Using a sessile droplet method, the equilibrium contact angle of an epoxy droplet on a tensile stress annealed MANC exhibits stress dependent surface energies. Anisotropic wetting in FeNi-based MANC heat treated at T CA = 440 °C mimics surface magnetic anisotropy observed by MOKE.

soft magnetic materials↗
NASA NTRS2015

Fine-Filament MgB2 Superconductor Wire

Hyper Tech Research, Inc., has developed fine-filament magnesium diboride (MgB2) superconductor wire for motors and generators used in turboelectric aircraft propulsion systems. In Phase I of the project, Hyper Tech demonstrated that MgB2 multifilament wires (<10 micrometers) could reduce alternating current (AC) losses that occur due to hysteresis, eddy currents, and coupling losses. The company refined a manufacturing method that incorporates a magnesium-infiltration process and provides a tenfold enhancement in critical current density over wire made by a conventional method involving magnesium-boron powder mixtures. Hyper Tech also improved its wire-drawing capability to fabricate fine multifilament strands. In Phase II, the company developed, manufactured, and tested the wire for superconductor and engineering current density and AC losses. Hyper Tech also fabricated MgB2 rotor coil packs for a superconducting generator. The ultimate goal is to enable low-cost, round, lightweight, low-AC-loss superconductors for motor and generator stator coils operating at 25 K in next-generation turboelectric aircraft propulsion systems.

Cantu, Sherrie↗
NASA NTRS1996

A Wide Bandwidth Model for the Electrical Impedance of Magnetic BearingS

Magnetic bearings are often designed using magnetic circuit theory. When these bearings are built, however, effects not included in the usual circuit theory formulation have a significant influence on bearing performance. Two significant sources of error in the circuit theory approach are the neglect of leakage and fringing effects and the neglect of eddy current effects. This work formulates an augmented circuit model in which eddy current and flux leakage and fringing effects are included. Through the use of this model, eddy current power losses and actuator bandwidth can be derived. Electrical impedance predictions from the model are found to be in good agreement with experimental data from a typical magnetic bearing.

Meeker, David C.↗
NASA NTRS1983

Magnetic Bearings for Inertial Energy Storage

The selection of a noncontacting bearing technique with no wear out phenomena and which is vacuum compatible which is the decisive factor in selecting magnetic bearings for kinetic energy storage was investigated. Unlimited cycle life without degradation is a primary goal. Storage efficiency is a key parameter which is defined as the ratio of the energy remaining to energy stored after a fixed time interval at no load conditions. Magnetic bearings, although noncontacting, are not perfectly frictionless in that magnetic losses due to eddy currents and hysteresis can occur. Practical magnetic bearings, however, deviate from perfect symmetry and have discontinuities and asymmetric flux paths either by design or when controlled in the presence of disturbances, which cause losses. These losses can be kept smaller in the bearings than in a high power motor/generator, however, are a significant factor in selecting the magnetic bearing type.

Studer, P. A.↗
NASA NTRS1995

Effects of atomic oxygen on polymeric materials flown on EOIM-3

Diverse polymeric materials, including several variations of Kapton, were flown on STS-46 as part of the Evaluation of Oxygen Interaction with Materials Experiment (EOIM-3). These materials were flown in the cargo bay and exposed to the space environment July 31 - August 8, 1992, including 40 hours of direct atomic oxygen impingement. The atomic oxygen exposure was approximately 2.2 x 10(exp 20) atoms/sq cm. Polymeric materials flown on EOIM-3 include coated and uncoated Kapton, Tefzel ETFE, Lexan, FEP and TFE Teflon, bulk Halar and PEEK, S383 silicone and Viton elastomeric seal material. Analyses performed included thickness measurements using Dektak and eddy current methods, mass loss, resistance, permeability, hardness, and FTIR. The effects of stress and the space environment on Kapton were also evaluated. Previous EOIM missions on STS-5 and STS-8 and the Long Duration Exposure Facility also contained polymeric material samples. Data from these previous flights are shown for comparison, as well as ground simulation of space environment effects using both thermal energy flow tubes and 5 eV neutral atomic oxygen beam facilities. Reaction efficiencies for the various atomic oxygen exposure conditions are discussed.

Kamenetzky, Rachel R.↗
NASA NTRS2001

Low loss pole configuration for multi-pole homopolar magnetic bearings

A new pole configuration for multi-pole homopolar bearings proposed in this invention reduces rotational losses caused by eddy-currents generated when non-uniform flux distributions exist along the rotor surfaces. The new homopolar magnetic bearing includes a stator with reduced pole-to-pole and exhibits a much more uniform rotor flux than with large pole-to-pole gaps. A pole feature called a pole-link is incorporated into the low-loss poles to provide a uniform pole-to-pole gap and a controlled path for pole-to-pole flux. In order to implement the low-loss pole configuration of magnetic bearings with small pole-to-pole gaps, a new stator configuration was developed to facilitate installation of coil windings. The stator was divided into sector shaped pieces, as many pieces as there are poles. Each sector-shaped pole-piece can be wound on a standard coil winding machine, and it is practical to wind precision layer wound coils. To achieve maximum actuation efficiency, it is desirable to use all the available space for the coil formed by the natural geometric configuration. Then, the coils can be wound in a tapered shape. After winding, the sectored-pole-pieces are installed into and fastened by bonding or other means, to a ring of material which encloses the sectored-pole-pieces, forming a complete stator.

Blumenstock, Kenneth A.↗
NASA NTRS1995

Stability mechanical considerations, and AC loss in HTSC monoliths, coils, and wires

For monolithic high-T(sub c) superconductors (HTSC's) calculations are presented of: (1) the initial flux jump field, H(sub fj), in melt-processed YBCO based on a field and temperature dependent J(sub c), and (2) the radial and circumferential stresses in solid and hollow cylinders containing trapped magnetic flux. For model multi filamentary (MF) HTSC/Ag strands calculations are presented of: (1) the limiting filament diameters for adiabatic and dynamic stability, and (2) the hysteretic and eddy current components of AC loss. Again for MF HTSC/Ag composite strands the need for filamentary subdivision and twisting is discussed.

Sumption, M. D.↗
NASA NTRS1987

Space station power semiconductor package

A package of high-power switching semiconductors for the space station have been designed and fabricated. The package includes a high-voltage (600 volts) high current (50 amps) NPN Fast Switching Power Transistor and a high-voltage (1200 volts), high-current (50 amps) Fast Recovery Diode. The package features an isolated collector for the transistors and an isolated anode for the diode. Beryllia is used as the isolation material resulting in a thermal resistance for both devices of .2 degrees per watt. Additional features include a hermetical seal for long life -- greater than 10 years in a space environment. Also, the package design resulted in a low electrical energy loss with the reduction of eddy currents, stray inductances, circuit inductance, and capacitance. The required package design and device parameters have been achieved. Test results for the transistor and diode utilizing the space station package is given.

Balodis, Vilnis↗
NASA NTRS1993

Characteristics of Ferromagnetic Flux Focusing Lens in the Development of Surface/Subsurface Flaw Detector

Electromagnetic NDE techniques have in the past steered away from the use of ferromagnetic materials. Although their high permeabilities lead to increased field levels, the properties of ferrous elements in the presence of alternating magnetic fields are difficult to determine. In addition, their use leads to losses which can be minimized through the use of low conductivity ferrites. In fact, the eddy current probes which do incorporate ferromagnetic materials have focused on these losses and the shielding which can be obtained by surrounding a probe with a high permeability, conducting material. Eddy current probes enclosed in conducting and magnetic shields have been used to prevent the generated fields from interacting with materials in the vicinity of the probe, such as when testing near material boundaries. A recent invention has used ferromagnetic shielding to magnetically separate individual concentric eddy current probes in order to eliminate cross-talk between the probes so that simultaneous detection of different types of flaws at different depths can be achieved. In contrast to the previous uses of ferromagnetic materials purely as magnetic shields, an electromagnetic flaw detector recently developed at NASA Langley Research Center takes advantage of the flux focusing properties of a ferromagnetic mild steel in order to produce a simple, effective device for the non-destructive evaluation of conducting materials. The Flux Focusing Eddy Current Probe has been shown to accurately measure material thickness and fatigue damage. The straight forward flaw response of the probe makes the device ideal for rapid inspection of large structures, and has lead to its incorporation in a computer controlled search routine to locate fatigue crack tips and monitor experimental fatigue crack growth experiments.

Wincheski, Buzz↗
NASA NTRS1996

Ultralow Friction in a Superconducting Magnetic Bearing

Passive levitation by superconducting magnetic bearings can be utilized in flywheels for energy storage. Basic design criteria of such a bearing are high levitation force, sufficient vertical and horizontal stability and low friction. A test facility was built for the measurement and evaluation of friction in a superconducting magnetic bearing as a function of operating temperature and pressure in the vacuum vessel. The bearing consists of a commercial disk shaped magnet levitated above single grain, melt-textured YBCO high-temperature superconductor material. The superconductor was conduction cooled by an integrated AEG tactical cryocooler. The temperature could be varied from 50 K to 80 K. The pressure in the vacuum chamber was varied from 1 bar to 10(exp -5) mbar. At the lowest pressure setting, the drag torque shows a linear frequency dependence over the entire range investigated (0 less than f less than 40 Hz). Magnetic friction, the frequency independent contribution, is very low. The frequency dependent drag torque is generated by molecular friction from molecule-surface collisions and by eddy currents. Given the specific geometry of the set-up and gas pressure, the molecular drag torque can be estimated. At a speed of 40 Hz, the coefficient of friction (drag-to-lift ratio) was measured to be mu = 1.6 x 10(exp -7) at 10(exp -5) mbar and T = 60 K. This is equivalent to a drag torque of 7.6 x 10(exp -10) Nm. Magnetic friction causes approx. 1% of the total losses. Molecular friction accounts for about 13% of the frequency dependent drag torque, the remaining 87% being due to eddy currents and losses from rotor unbalance. The specific energy loss is only 0.3% per hour.

Bornemann, Hans J.↗
NASA NTRS1977

Low-loss energy storage flywheel

Magnetically-levitated, ironless-armature spokeless rotor is used. Ironless armature construction eliminates core losses due to hysteresis and eddy currents. Device combines features of homopolar salient poles and stationary ironless electronically commutated armature.

Evans, H. E.↗
NASA NTRS2022

Calculation of Transformer Leakage Inductance by Simplified Flux Path Geometries

Series inductance is a critical energy storage element in isolated power converters. Many have explored methods of estimating the total leakage inductance of transformers as an integrated series inductance without external inductors. However, this poses challenges with medium frequency converters and magnetic ribbon-based cores, e.g., metal amorphous nanocrystalline. The material’s relatively high conductivity allows eddy currents to develop when magnetic flux intersects wide surfaces. These eddy currents result in significant additional losses that increase with increasing power flow. This paper presents a simplified and accurate method of estimating leakage flux while identifying separate leakage flux paths that correlate with the magnetic material surfaces. This enables an understanding the proportion of leakage flux that will contribute to extra losses. The methods presented are applicable to both leakage and fringing (around heterogeneous material interfaces) fluxes. This paper includes detailed FEA studies and 3D flux vector measurements matching the presented analytical models.

transformer↗
NASA NTRS1978

Trapped-flux spin-down torques on a spherical superconducting gyroscope

Magnetic flux trapped in the rotor of a superconducting gyroscope can cause the rotor to lose energy through dissipation in a readout loop encompassing the rotor and by the generation of eddy currents in the support electrodes. These losses are calculated and shown to be negligible for the rotor in the gyroscope-relativity experiment, a proposed satellite experiment which is to test predictions of the theory of general relativity.

Holdeman, L. B.↗
NASA NTRS1991

Magnetostrictive direct drive motor

Highly magnetostrictive materials such as Tb.3Dy.7Fe2, commercially known as TERFENOL-D, have been used to date in a variety of devices such as high power actuators and linear motors. The larger magnetostriction available in twinned single crystal TERFENOL-D, approx. 2000 ppm at moderate magnetic field strengths, makes possible a new generation of magnetomechanical devices. NASA researchers are studying the potential of this material as the basis for a direct microstepping rotary motor with torque densities on the order of industrial hydraulics and five times greater than that of the most efficient, high power electric motors. Such a motor would be a micro-radian stepper, capable of precision movements and self-braking in the power-off state. Innovative mechanical engineering techniques are juxtaposed on proper magnetic circuit design to reduce losses in structural flexures, inertias, thermal expansions, eddy currents, and magneto-mechanical coupling, thus optimizing motor performance and efficiency. Mathematical models are presented, including magnetic, structural, and both linear and nonlinear dynamic calculations and simulations. In addition, test results on prototypes are presented.

Naik, Dipak↗
NASA NTRS1974

Induction brazing at the Kennedy Space Center

A description of the joint design, materials, equipment, qualification testing, inspection methods, and applications involved in performing induction brazing on hyperbolic propellants tubing at Kennedy Space Center. Induction brazing is a form of brazing in which the energy is transmitted to the workpiece by electrical induction; the eddy currents generated in the metal produce heat by resistance losses. Since induction heating is fast and highly localized, undesirable heat effects are minimized and the resulting braze is of high quality.

Clautice, W. E.↗
NASA NTRS2018

Study of Dissipative Losses in AC-Biased Mo/Au Bilayer Transition-Edge Sensors

We are developing kilo-pixel arrays of transition-edge sensors (TESs) for the X-ray Integral Field Unit on ESA's (European Space Agency's) Athena observatory. Previous measurements of AC-biased Mo/Au TESs have highlighted a frequency-dependent loss mechanism that results in broader transitions and worse spectral performance compared to the same devices measured under DC (Direct Current) bias. In order to better understand the nature of this loss, we are now studying TES pixels in different geometric configurations. We present measurements on devices of different sizes and with different metal features used for noise mitigation and X-ray absorption. Our results show how the loss mechanism is strongly dependent upon the amount of metal in close proximity to the sensor and can be attributed to induced eddy current coupling to these features. We present a finite element model that successfully reproduces the magnitude and geometry dependence of the losses. Using this model, we present mitigation strategies that should reduce the losses to an acceptable level.

Sakai, K.↗