Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “downwind”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence D - Raw Data

Sequences B, C, and D: Downwind Baseline (F), Downwind Low Pitch (F), Downwind High Pitch (F) This test sequence used a downwind, teetered turbine with a 3.4° cone angle. The wind speed ranged from 5 m/s to 25 m/s. Yaw angles of ±180° were achieved at low wind speeds, and yaw angles of -20° to 10° were achieved for high wind speeds. The blade tip pitch was 3° for sequence B, 0° for sequence C, and 6° for sequence D. These three sequences were interleaved during testing because the pitch angle change was easily made by the turbine operator. The rotor rotated at 72 RPM. Blade and probe pressure measurements were collected.

17 WIND ENERGY↗
DOE OSTI2022

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence 8 - Raw Data

Sequences 8 and 9: Downwind Sonics (F,P) and Downwind Sonics Parked (P) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed ranged from 5 m/s to 25 m/s. Yaw angles of 0° to 60° were achieved. The blade tip pitch was 3°. The rotor rotated at 72 RPM during Sequence 8, but it was parked during Sequence 9. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm-thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to –99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. During post-processing, the probe channels were set to read -99999.99. Sonic anemometers were mounted on a strut downwind of the turbine. The strut was mounted to the T-frame, which was rotated to align the anemometers aft of the 9% and 49% radius locations at hub height. Because of this configuration, the tunnel balance data are considered invalid. Sequence 9 was designed to compare the downwind sonic anemometer readings with the upwind sonic anemometers without interference from the turbine. The rotor was parked with the instrumented blade at 0° azimuth. All pressure measurements obtained in Sequence 9 are invalid because sufficient time for temperature stabilization did not occur, thus all associated data values were flagged as not applicable by setting the measured values in the data file to 0.0000 Pa. This test is further described in Appendix G.

17 WIND ENERGY↗
DOE OSTI2022

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence 9 - Raw Data

Sequences 8 and 9: Downwind Sonics (F,P) and Downwind Sonics Parked (P) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed ranged from 5 m/s to 25 m/s. Yaw angles of 0° to 60° were achieved. The blade tip pitch was 3°. The rotor rotated at 72 RPM during Sequence 8, but it was parked during Sequence 9. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm-thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to –99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. During post-processing, the probe channels were set to read -99999.99. Sonic anemometers were mounted on a strut downwind of the turbine. The strut was mounted to the T-frame, which was rotated to align the anemometers aft of the 9% and 49% radius locations at hub height. Because of this configuration, the tunnel balance data are considered invalid. Sequence 9 was designed to compare the downwind sonic anemometer readings with the upwind sonic anemometers without interference from the turbine. The rotor was parked with the instrumented blade at 0° azimuth. All pressure measurements obtained in Sequence 9 are invalid because sufficient time for temperature stabilization did not occur, thus all associated data values were flagged as not applicable by setting the measured values in the data file to 0.0000 Pa. This test is further described in Appendix G.

17 WIND ENERGY↗
DOE OSTI2025

Computational Fluid Dynamics-Based Modeling of Methane Flows Around Oil and Gas Equipment

Recent studies estimate that emissions from oil and gas production facilities contribute between 20 and 50% of the total methane ( CH 4 ) emitted in the US; therefore, quantifying and reducing these emissions are crucial for achieving climate goals. Methane quantification depends on both measuring methane concentrations and converting them to emissions through a modeling framework. Currently, simple atmospheric dispersion models are primarily used to quantify emissions and concentrations, but these estimates are highly uncertain when quantifying emissions from complex aerodynamic sources, such as oil and gas facilities. This investigation used a CFD modeling approach, which can account for aerodynamic complexity but has hitherto not been used to model methane concentrations downwind of a methane release of a known rate, and compared it against in situ measurements. High-time-resolution (1 Hz) methane concentration and meteorological data were measured during experiments conducted at the METEC on 21 March and 11 July 2024. The METEC site configuration, measured wind data, and controlled emission rates were used as input for the CONVERGE CFD model to model downwind CH 4 concentration. The modeling was carried out between 20 and 70 m, from two different points of release in two separate controlled-release experiments, one from a separator and another from a wellhead. In these experiments, we found that the CFD model could predict the CH 4 concentrations downwind of the release to a good degree. The model was evaluated on multiple metrics to assess its performance in estimating methane concentrations at typical fence line distances (∼30 m). These results help us to understand external flows and the ability of CFD models to predict downwind concentrations in aerodynamically complex environments.

03 NATURAL GAS↗
DOE OSTI2026

Citizen science coupled with machine learning to quantify green-blue infrastructure cooling potential in Maricopa County, Arizona

Here, this study investigates the spatiotemporal cooling performance of green and blue infrastructure (GBI) in the Dobson Ranch urban neighborhood in Phoenix, Arizona. We leveraged citizen science near-surface (2 m) air temperature (Tair) measurements to train a highly accurate Tair predicting LightGBM machine learning model (R 2 : 0.986, MAE: 0.251 °C, RMSE: 0.585 °C). On June 16, 2024, the park area exhibited approximately 1 °C cooling effect (relative to the neighborhood mean) during both day and night. In contrast, the nearby artificial lake exhibited a stronger cooling effect of 2.4 °C during the day but a slight warming of 0.3 °C at night. At 00:00, locations 50 m downwind of the park were 0.3 °C warmer than the park, while locations 50 m upwind were 0.8 °C warmer. At 11:00, we observed that the downwind area is 0.8 °C cooler and the upwind area is 0.6 °C warmer—at the same 50 m distances relative to the park. We also observed 1 °C cooler and warmer effects respectively at the same 50 m downwind and upwind locations at 19:00 on June 17, 2024. Our data-driven analysis highlights potential limitations of car-traverse measurements, showing that failure to account for temporal variations during the traverse can lead to overestimation of Tair at night and underestimation during the day. Our analysis also showed only a weak correlation (coefficient: 0.48) between Landsat-derived land surface temperature (LST) and model predicted Tair at the time of the local Landsat overpass (∼11.00). This highlights the potential error of relying solely on LST for human thermal exposure analysis—particularly within the heterogenous built-environment.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Data Center Waste Heat as an Emerging Urban Thermal Hazard: First Field Measurements of Neighborhood-Scale Air Temperature Impacts

Data centers are among the fastest-growing sources of concentrated anthropogenic heat in urban environments. Despite heat flux densities that exceed peak solar irradiance by a factor of 2–6, their thermal impacts on adjacent communities have never been directly measured or reported in the peer-reviewed literature. This short communication addresses that gap by presenting the first vehicle-based traverse measurements of air temperature in residential neighborhoods downwind of operational data centers. Five traverses at four facilities in the Phoenix, Arizona metropolitan area, ranging from a 36 MW single-building data center in Mesa to a 169 MW colocation campus in Chandler, reveal downwind air temperature warming as high as 2.2 °C, with average downwind air temperatures 0.7–0.9 °C warmer than corresponding upwind areas. Thermal signatures were detectable at distances up to 500 m from facility perimeters. The 36 MW Mesa facility rejects waste heat equivalent to the electricity consumption of approximately 40,000 households, while the 169 MW Chandler campus is equivalent to over 180,000 households, both concentrated into footprints smaller than a single residential subdivision. With U.S. data center capacity projected to more than double by 2030, these findings establish data center anthropogenic waste heat as a previously undocumented urban thermal hazard demanding attention from the data center and urban planning communities.

Phoenix↗
DOE OSTI2022

Evaluation of the Fitch Wind-Farm Wake Parameterization with Large-Eddy Simulations of Wakes Using the Weather Research and Forecasting Model

Abstract Wind-farm parameterizations in weather models can be used to predict both the power output and farm effects on the flow; however, their correctness has not been thoroughly assessed. We evaluate the wind-farm parameterization of the Weather Research and Forecasting Model with large-eddy simulations (LES) of the wake performed with the same model. We study the impact on the velocity and turbulence kinetic energy (TKE) of inflow velocity, roughness, resolution, number of turbines (one or two), and inversion height and strength. We compare the mesoscale with the LES by spatially averaging the LES within areas correspondent to the mesoscale horizontal spacing: one covering the turbine area and two downwind. We find an excellent agreement of the velocity within the turbine area between the two types of simulations. However, within the same area, we find the largest TKE discrepancies because in mesoscale simulations, the turbine-added TKE has to be highest at the turbine position to be advected downwind. Within the downwind areas, differences between velocities increase as the wake recovers faster in the LES, whereas for the TKE both types of simulations show similar levels. From the various configurations, the impact of inversion height and strength is small for these heights and inversion levels. The highest impact for the one-turbine simulations appears under the low-speed case due to the higher thrust, whereas the impact of resolution is low for the large-eddy simulations but high for the mesoscale simulations. Our findings demonstrate that higher-fidelity simulations are needed to validate wind-farm parameterizations.

17 WIND ENERGY↗
DOE OSTI2024

50 MW Segmented Ultralight Morphing Rotors for Wind Energy

A multi-institutional team designed a 50 Megawatt (MW) rated wind turbine featuring downwind aeroelastic morphing to reduce blade loads and allow an ultralight segmented rotor (mass reduction of about 25% compared to a conventional upwind rotor). The team used a control co-design approach with state-of-the art simulations including for the rotor and tower design using non-linear fluid-structure interactions and control algorithms, and the team also designed, built, and field-tested an aeroelastically-scaled downwind rotor to demonstrate this novel technology and validate the design tool fidelity. In a follow-on phase, these results were used along with an updated Levelized Cost Of Energy (LCOE) methodology to co-design a more detailed set of 25 MW rated turbine designs (including individual pitch control) based on minimum LCOE with highly flexible blades for an Atlantic Ocean offshore fixed-bottom design targeted towards market technology evaluation. A set of upwind and downwind designs at 25 MW rated scales were found to provide the best LCOE, with strong improvements over all previous offshore reference turbines (NREL 5MW, DTU 10 MW and IEA 15 MW). The optimized design would represent the world’s largest offshore turbine design, which combines several state-of-the-art structural, aerodynamic, and control technologies into a new and optimized system concept.

17 WIND ENERGY↗
DOE OSTI2025

Investigation of Main Bearing Fatigue Estimate Sensitivity to Synthetic Turbulence Models Using a Novel Drivetrain Model Implemented in OpenFAST

ABSTRACT A coupled medium‐fidelity drivetrain model is developed and implemented in OpenFAST for a 10‐MW land‐based reference turbine. The implementation is verified against a fully coupled multibody wind turbine model, including a detailed drivetrain. The new model can simultaneously and accurately estimate main bearing loads and represent elastic bending of the drivetrain. It has low computational cost and is useful for early design phases, sensitivity analyses and complex systems like wind farms (where computational expense must be expended elsewhere). Here, the model is implemented for a monopile offshore wind turbine and used to investigate the sensitivity of main bearing basic rating life to different synthetic turbulence models. Large‐eddy simulations (LES) targeting stable, neutral, and unstable atmospheric conditions at below‐, near‐ and above‐rated wind speeds are used as a reference. The turbulence models recommended by the International Electrotechnical Commission, the Mann spectral tensor model, and the Kaimal spectral model with exponential coherence are fitted to the LES data. Additionally, a constrained turbulence generator, PyConTurb (short for Python Constrained Turbulence ), based on LES data, is applied in the aero‐hydro‐servo‐elastic simulations. Taking PyConTurb as the baseline, the Kaimal model significantly underestimates fatigue of the downwind main bearing, with between 10% and 40% less damage. The Mann model also underestimates the downwind main bearing fatigue by up to 30%. The upwind main bearing damage is driven by mean loads, and differences between models are less significant, although the trends are similar. Reasons for these discrepancies are investigated and attributed to differences in spatial and temporal variations among the turbulence models.

17 WIND ENERGY↗
DOE OSTI2023

Review of particle deposition to and removal from clothing, skin, and hair after a radioactive airborne dispersal event

Explosive Radiological Dispersal Devices (RDD) – aka dirty bombs – are seen as a credible method to carry out a radiological terror attack. After exploding a radioactive source, the radionuclide-laden plume will be blown downwind of ground zero, with particles falling out and potentially depositing on people caught in and under the cloud. Some of these people may not show any sign of radiation sickness and therefore not realize they have been contaminated and may take the radioactive particulate with them on their daily activities, thus spreading the radioactive particulate outside the initially contaminated area. This paper reviews the scientific literature to better understand the rate at which particulate deposits on and is removed from the different “surfaces” of a person, i.e., hair, skin, and clothing. Prior research indicates that: 1) particle deposition is usually higher on skin than on hair and clothing; 2) particle deposition is greater for a person with higher skin moisture, 3) stronger wind increases the deposition flux onto a person, and 4) the fraction of particulate deposited on the hair, skin, and clothing respectively depends on the length of the hair, assuming all the hair surface is available for deposition. The studies taken into consideration show that the largest uncertainty in particulate deposition onto a person is due to clothing type because of the different possible weave arrangements and tightness which translate into differences in actual surface area and surface roughness. A factor of 2-to-20 variation in deposition rate was found. Removal of the particulate from the contaminated person may be due to wind, a person's movement, and/or contact transfer, i.e., by touching a different clean surface. Experiments show that the majority of the particulate is resuspended within 2–6 h mostly depending on the intensity of physical activity. The largest uncertainty in particulate removal from skin depends on the skin moisture, transfer rate of single-contact, and how many objects/people a person touches per hour. No data for hair were found for particle removal and resuspension. The studies considered did not utilize radionuclides directly; however, data on adhesion of radioactive vs. their non-radioactive counterpart have shown that the uncertainty due to the radioactivity of the particles is lower than that due to other factors. In conclusion, an idealized scenario involving a single building in the path of the cloud showed the impact of building-influenced flow on the cloud transport path and mixing, which affects the radiological dose the downwind population is exposed to and consequently the health effects.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗
DOE OSTI2024

Urban Effect on Precipitation and Deep Convective Systems Over Dallas‐Fort Worth

A range of multi-year observational data sets are used to characterize the hydroclimate of the Dallas Fort-Worth area (DFW) and to investigate the impact of urban land cover on daily accumulated precipitation, RADAR composite reflectivity (cREF), and cloud top height (CTH) during the warm season. Analyses of observational data indicate rainfall rates (RR) in a 45° annulus sector 50–100 km downwind of the city are enhanced relative to an upwind area of comparable size. Enhancement of mean precipitation intensity in this annulus sector is not observed on days with spatially averaged RR > 6 mm/day. Under some flow directions, the probability of cREF >30 dBZ, occurrence of hail, and the probability of CTH >10,000 geopotential meters are also enhanced up to 200 km downwind of DFW. Two deep convection events that passed over DFW are simulated with the Weather Research and Forecasting model using a range of microphysical schemes and evaluated using RADAR observations. Model configurations that exhibit the highest fidelity in these control simulations are used in a series of perturbation experiments where the areal extent of the city is varied between zero (replacement with grassland) and eight times its current size. These perturbation experiments indicate a non-linear response of Mesoscale Convective System properties to the urban areal extent and a very strong sensitivity to the microphysical scheme used. The impact on precipitation from the urban area, even when it is expanded to eight-times the current extent, is much less marked for deep convection with stronger synoptic forcing.

58 GEOSCIENCES↗
DOE OSTI2024

Upwind Moisture Controls on Interannual Variations of Precipitation and Vegetation in China's Drylands

Dryland precipitation depends on upwind and local moisture sources via moisture recycling. How upwind moisture variations affect interannual variations of downwind precipitation and vegetation in China's drylands remains unclear. We used high-resolution moisture tracking data sets and found terrestrial moisture (93%) was the dominant moisture source for China's drylands, especially from drylands themselves (46%). In most dryland grids, we observed strong correlations between precipitation and upwind moisture sources from 2003 to 2022 (median r = 0.55), with a more significant effect in drier areas. These demonstrated the upwind moisture control on interannual variations of dryland precipitation, in which internal moisture from drylands exceeds the influence of external terrestrial sources. The upwind moisture variations, especially the recycled moisture of drylands, propagate to influence downwind vegetation greenness in precipitation-sensitive dryland areas. Our findings revealed that upwind moisture variations induced by climate or land-cover changes have important implications for water and food security in China's drylands.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Summer Convective Precipitation Changes Over the Great Lakes Region Under a Warming Scenario

To understand future summer precipitation changes over the Great Lakes Region (GLR), we performed an ensemble of regional climate simulations through the Pseudo-Global Warming (PGW) approach. We found that different types of convective precipitation respond differently to the PGW signal. Isolated deep convection (IDC), usually concentrated in the southern domain, shows an increase in precipitation to the north of the GLR. Mesoscale convective systems (MCSs), usually concentrated upwind of the GLR, shift to the downwind region with increased precipitation. Thermodynamic variables such as convective available potential energy (CAPE) and convective inhibition energy (CIN) are found to increase across almost the entire studied domain, creating a potential environment more favorable for stronger convection systems and less favorable for weaker ones. Meanwhile, changes in the lifting condensation level (LCL) and level of free convection (LFC) show a strong correlation with variations in convective precipitation, highlighting the significance of these thermodynamic factors in controlling precipitation over the domain. Our results indicate that the decrease in LCL and LCF in areas with increased convective precipitation is mainly due to increased atmospheric moisture. In response to the prescribed warming perturbation, MCSs occur more frequently downwind, while localized IDCs exhibit more intense rain rates, longer durations, and larger rainfall area.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Urban Land Surface Effects on Summertime Clouds and Moist Convection in Houston Under Different Synoptic Conditions

Urban landscapes modify cloud formation and convection through complex thermodynamic and aerodynamic processes; however, their influence under different synoptic regimes remains poorly understood. This study investigates the impact of the Houston metropolitan area on summertime cloud cover and convective cell characteristics using a combination of satellite observations, radar data, and high-resolution process-based modeling. We isolate urban effects by comparing model simulations with realistic urban land cover against hypothetical scenarios where all urban areas are replaced by rural vegetation. Results reveal that Houston's land cover consistently enhances cloud fraction and convective activity relative to surrounding rural areas, altered by large-scale meteorological forcing. Under weakly forced conditions, enhanced surface heat flux primarily contributes to driving low-level convergence and vertical ascent, leading to over 8% cloud fraction increase between 2 and 6 km over the city. Under strongly forced conditions, urban influences manifest differently depending on cloud type. For non-convective clouds, the city acts as a barrier that decelerates and lifts moist southerly inflow, increasing low cloud cover over the urban core, while decreasing it downwind the city. For convective clouds, both synoptic ascent and urbanization modulate moisture redistribution and cloud structure, producing modest cloud enhancement over the city and slight suppression over the downwind area. Urbanization exerts small changes in the intensity of the convective cells; however, it significantly decreases their duration and traveling distance. This work highlights the importance of accounting for land surface heterogeneity in modeling clouds and precipitation and demonstrates that urban impacts on clouds are highly regime-dependent.

Liu, Ye [Pacific Northwest National Laboratory (PN↗
DOE OSTI2022

Extensive urban air pollution footprint evidenced by submicron organic aerosols molecular composition

Transport and transformation of urban air pollutants are among the major factors driving the changes in the atmospheric composition in the downwind rural/remote areas of a megacity. Here, we assess the impacts of urban air pollution in a subtropical forest through characterization of the organic markers in submicron aerosol particles. The aerosol samples were collected and analyzed using TD-PTR-ToF-MS, where 163 ions were detected. The concentration of these extracted ions accounts for 83% of the mass of submicron organic aerosols, which are accordingly characterized by a median formula of C 7 H 10 O 2 . Molecular speciation indicates that urban and biomass burning pollution contributed substantially to the budget of organic aerosols, which were enhanced particularly by the liquid water content and acidity of the aerosols. Our results evidence that the footprint of urban air pollution was extended to its downwind forested areas and caused changes in the concentration and composition of submicron aerosols.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Cloud microphysical response to entrainment and mixing is locally inhomogeneous and globally homogeneous: Evidence from the lab

Entrainment of dry air into clouds strongly influences cloud optical and precipitation properties and the response of clouds to aerosol perturbations. The response of cloud droplet size distributions to entrainment–mixing is examined in the Pi convection-cloud chamber that creates a turbulent, steady-state cloud. The experiments are conducted by injecting dry air with temperature (T e ) and flow rate (Q e ) through a flange in the top boundary, into the otherwise well-mixed cloud, to mimic the entrainment–mixing process. Due to the large-scale circulation, the downwind region is directly affected by entrained dry air, whereas the upwind region is representative of the background conditions. Droplet concentration (Cn) and liquid water content (L) decrease in the downwind region, but the difference in the mean diameter of droplets (D m ) is small. The shape of cloud droplet size distributions relative to the injection point is unchanged, to within statistical uncertainty, resulting in a signature of inhomogeneous mixing, as expected for droplet evaporation times small compared to mixing time scales. As T e and Q e of entrained air increase, however, Cn, L, and D m of the whole cloud system decrease, resulting in a signature of homogeneous mixing. The apparent contradiction is understood as the cloud microphysical responses to entrainment and mixing differing on local and global scales: locally inhomogeneous and globally homogeneous. This implies that global versus local sampling of clouds can lead to seemingly contradictory results for mixing, which informs the long-standing debate about the microphysical response to entrainment and the parameterization of this process for coarse-resolution models.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Glaciation of liquid clouds, snowfall, and reduced cloud cover at industrial aerosol hot spots

The ability of anthropogenic aerosols to freeze supercooled cloud droplets remains debated. Here, in this work, we present observational evidence for the glaciation of supercooled liquid-water clouds at industrial aerosol hot spots at temperatures between -10° and -24°C. Compared with the nearby liquid-water clouds, shortwave reflectance was reduced by 14% and longwave radiance was increased by 4% in the glaciation-affected regions. There was an 8% reduction in cloud cover and an 18% reduction in cloud optical thickness. Additionally, daily glaciation-induced snowfall accumulations reached 15 millimeters. Glaciation events downwind of industrial aerosol hot spots indicate that anthropogenic aerosols likely serve as ice-nucleating particles. However, rare glaciation events downwind of nuclear power plants indicate that factors other than aerosol emissions may also play a role in the observed glaciation events.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Measuring the Effects of Wake Steering With Nacelle-Mounted Scanning Lidar

In large wind plants, wakes from upwind turbines affect downwind turbines by reducing wind speeds and increasing turbulence. Wake steering may mitigate this effect by deflecting the wakes of upwind turbines away from downwind units. Here, we characterize the impact of wakes from yawed turbines at a commercial-scale wind plant under varying atmospheric and turbine operating conditions. Six months of nacelle-based lidar measurements were collected as part of a field campaign in 2019-2020 in the northern US Great Plains to test the effectiveness of wake steering. We separate these lidar scans by atmospheric stability and turbine operating condition to summarize how yawed wind turbine wakes vary with these input parameters in the atmospheric boundary layer. We summarize the impact of wake steering on various wake characteristics including velocity deficit, wake width, and wake center as retrieved from these lidar data. Yawed wakes have significantly different centerline characteristics compared to unyawed wakes, with large regions of meander in the mid wake region. Yawed wakes are also deflected farther than unyawed wakes in less turbulent conditions with velocity deficits persisting further downstream in stable atmospheric conditions. Overall, yawed wind turbine wakes are larger and wider in lower wind speed environments, and yawed wakes are deflected farther in less turbulent conditions, suggesting that wake steering is most effective in stable atmospheric stratification.

17 WIND ENERGY↗