Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “directional airflow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Augmentation of Stagnation Region Heat Transfer Due to Turbulence from a DLN Can Combustor

Heat transfer measurements have been made in the stagnation region of a flat plate with a circular leading edge. Electrically heated aluminum strips placed symmetrically about the leading edge stagnation region were used to measure spanwise-averaged heat transfer coefficients. The maximum Reynolds number obtained, based on leading edge diameter, was about 100,000. The model was immersed in the flow field downstream of an approximately half-scale model of a can-type combustor from a low NO(x), ground-based power-generating turbine. The tests were conducted with room temperature air; no fuel was added. Room air flowed into the combustor through six vane-type fuel/air swirlers. The combustor can contained no dilution holes. The fuel/air swirlers all swirled the incoming airflow in a counterclockwise direction (facing downstream). A five-hole probe flow field survey in the plane of the model stagnation point showed the flow was one big vortex with flow angles up to 36 deg at the outer edges of the rectangular test section. Hot-wire measurements showed test section flow had very high levels of turbulence, around 28.5%, and had a relatively large axial-length scale-to-leading edge diameter ratio of 0.5. X-wire measurements showed the turbulence to be nearly isotropic. Stagnation heat transfer augmentation over laminar levels was around 77% and was about 14% higher than predicted by a previously developed correlation for isotropic grid-generated turbulence.

VanFossen, G. James↗
NASA NTRSDate not supplied

Effect of Liner Cooling Flow on Combustor Emissions for Commercial Supersonics Technology

An overview is provided of a parametric study conducted to study the effect of liner cooling airflow rates on NOx emissions of a seven-element lean-direct injection (LDI) module with radial airflow main swirlers. The goal of the CFD study was to determine the increase in cooling flow rate at which the NOx emissions would exceed 20% of the predicted emissions with zero liner cooling flow. The Open version of the National Combustion Code (OpenNCC) was used to perform two-phase reacting flow computations with a new LDI injection module design with radial airflow swirlers instead of axial airflow swirlers. CFD analysis with OpenNCC predicted a 20% increase in EINOx emissions was reached when the liner cooling airflow rate was increased to 15% of the baseline combustor airflow rate. The liner cooling flow rate was predicted to have a non-linear effect on increase in overall EINOx of the seven element LDI injection module.

CFD↗
NASA NTRS2000

Recent Studies on Methanol Crossover in Liquid-Feed Direct Methanol Fuel Cells

In this work, the effects of methanol crossover and airflow rates on the cathode potential of an operating direct methanol fuel cell are explored. Techniques for quantifying methanol crossover in a fuel cell and for separating the electrical performance of each electrode in a fuel cell are discussed. The effect of methanol concentration on cathode potential has been determined to be significant. The cathode is found to be mass transfer limited when operating on low flow rate air and high concentrations of methanol. Improvements in cathode structure and operation at low methanol concentration have been shown to result in improved cell performance.

Valdez, T. I.↗
NASA NTRS1982

Noise measurement in wind tunnels, workshop summary

In reviewing the progress made in acoustic measurements in wind tunnels over the 5-yr span of the workshops, it is evident that a great deal of progress has occurred. Specialized facilities are now on line, special measurement techniques were developed, and corrections were devised and proven. This capability is in the process of creating a new and more correct data bank on acoustic phenomena, and represents a major step forward in acoustics technology. Additional work is still required, but now, rather than concentrating on facilities and techniques, researchers may more profitably concentrate on noise-source modeling, with the simulation of propulsor noise source (in flight) and of propulsor/airframe airflow characteristics. Promising developments in directional acoustic receivers and other discrimination/correlation techniques should now be regularly exploited, in part for model noise-source diagnosis, but also to expedite extraction of the lone source signal from any residual background noise and reverberation in the working chamber and from parasitic noise due to essential rigs or instrumentation inside the airstream.

Hickley, D. H.↗
NASA NTRS1987

Hot-Gas Nozzle for Desoldering Leadless IC's

Simple hand-held tool removes leadless, surface-mounted integrated circuits (IC's) from printed-circuit boards. Nozzle used with hot-air gun of type used to apply heat-shrink tubing or with some other source of hot gas. Rectangular end of nozzle and deflector shape airflow pattern to concentrate heat directly on soldering pads located around edge of IC's to heat them quickly and uniformly.

Hanlon, Mark T.↗
NASA NTRS2000

Augmentation of Stagnation Region Heat Transfer Due to Turbulence From a DLN Can Combustor

Heat transfer measurements have been made in the stagnation region of a flat plate with a circular leading edge. Electrically heated aluminum strips placed symmetrically about the leading edge stagnation region were used to measure spanwise averaged heat transfer coefficients. The maximum Reynolds number obtained, based on leading edge diameter, was about 100,000. The model was immersed in the flow field downstream of an approximately half scale model of a can-type combustor from a low NO(x), ground based power-generating turbine. The tests were conducted with room temperature air; no fuel was added. Room air flowed into the combustor through six vane type fuel/air swirlers. The combustor can contained no dilution holes. The fuel/air swirlers all swirled the incoming airflow in a counter clockwise direction (facing downstream). A 5-hole probe flow field survey in the plane of the model stagnation point showed the flow was one big vortex with flow angles up to 36' at the outer edges of the rectangular test section. Hot wire measurements showed test section flow had very high levels of turbulence, around 28.5 percent, and had a relatively large axial-length scale-to-leading edge diameter ratio of 0.5. X-wire measurements showed the turbulence to be nearly isotropic. Stagnation heat transfer augmentation over laminar levels was around 77 percent and was about 14 percent higher than predicted by a previously developed correlation for isotropic grid generated turbulence.

VanFossen, G. James↗
NASA NTRS1991

Technology development activities for housing research animals on Space Station Freedom

The development and design of animal facilities are described in terms of the technological needs for NASA's Biological Flight Research Laboratory. Animal habitats are presented with illustrations which encompass waste-collection techniques for microgravity conditions that reduce the need for crew participation. The technology is intended to be highly compatible with animal morphology, and airflow is employed as the primary mechanism of waste control. The airflow can be utilized in the form of localized high-speed directed flow that simultaneously provides a clean animal habitat and low airflow rates. The design of an animal-habitat testbed is presented which capitalizes on contamination-control mechanisms and suitable materials for microgravity conditions. The developments in materials and technologies represent significant contributions for the design of the centrifuge facilities for the Space Station Freedom.

Jenner, Jeffrey W.↗
NASA NTRS1974

Results from cascade thrust reverser noise and suppression experiments

Results from experimental work on model scale cascade reversers with cold airflow are presented. Sound power level directivity and spectral characteristics for cascade reversers are reported. Effect of cascade exit area ratio, vane profile shape, and emission arc are discussed. Model equivalent diameters varied from 3 to 5 inches, pressure ratios range from 1.15 to 3.0. Depending on the reverser type, acoustic power was proportional to the 4 1/2 to 6th power of ideal jet velocity. Reverser noise peaked at higher frequency and was more omnidirectional than nozzle-alone jet noise. Appreciable reduction in sideline noise was obtained from plane shields. Airfoil-vaned cascades were the most aerodynamically efficient and least noisy reversers. Scaling of cascade reverser data to example aircraft engines showed all cascades above the 95 PNdB sideline goal from STOL aircraft. However, the airfoil-vaned reverser has a good potential for meeting this goal for high-bypass (low pressure ratio) exhausts.

Gutierrez, O. A.↗
NASA NTRS1974

Results from cascade thrust reverser noise and suppression experiments

Results from experimental work on model scale cascade reversers with cold airflow are presented. Sound power levels, directivity, and spectral characteristics for cascade reversers are reported. Effect of cascade exit area ratio, vane profile shape, and emission arc are discussed. Model equivalent diameters varied from 3 to 5 inches; pressure ratios ranged from 1.15 to 3.0. Depending on the reverser type, acoustic power was proportional to the 4.5- to 6-th power of ideal jet velocity. Reverser noise peaked at higher frequency and was more omnidirectional than nozzle-alone jet noise. Appreciable reduction in sideline noise was obtained from plane shields.

Gutierrez, O. A.↗
NASA NTRS1983

Measuring Surface-Shear Stress in a Wind Tunnel

Two-wire skin friction gage gives both magnitude and direction of mean and fluctuating stresses. Heated wires lie at surface of gage, measure airflow by cooling effect. Wires perpendicular to each other to measure flow direction as well as magnitude. Used successfully in various turbulent flow fields, including separating three-dimensional boundary layer over cone at high angle of incidence.

Lemos, F.↗
NASA NTRS1990

Flight investigation of the effect of tail boom strakes on helicopter directional control

A joint U.S. Army/NASA flight investigation was conducted utilizing an instrumented Bell 240B single-rotor helicopter to determine the effectiveness of horizontally-mounted tail boom strakes on directional controllability and tail rotor power required during low-speed, crosswind operating conditions. The purpose of the strakes was to separate airflow over the tail boom and change fuselage yawing moments in a direction to improve the yaw control margin and reduce tail rotor power required. Low-speed crosswind data were obtained in 5-knot increments at airspeeds of 0 knots to 35 knots and for 30 deg increments in wind azimuth from 0 to 330 deg. In right sideward flight at the most critical wind azimuth and airspeed (60 deg azimuth measured from the nose of the aircraft and 20 knots airspeed), the strakes improved the pedal margin by about 6 percent of total travel and reduced the tail rotor power required by 17 percent. The increase in yaw control and reduction in tail rotor power offered by the strakes can expand the operating envelope in terms of gross weight and altitude capability. No effects in forward flight were noted.

Kelley, Henry L.↗
NASA NTRS1998

Development of a mirror pointing mechanism for an atmospheric gas measurement instrument

Development of the Open Path Tunable Infrared Monitor of the Atmosphere (OPTIMA) instrument involved designing a pair of motion systems that could maintain a precise alignment and spatial distance between two mirrors installed on the NASA DC-8 research laboratory aircraft. This is the first airborne optical instrument that allows direct measurement of the gases in the freestream airflow on the exterior of the aircraft. One mirror is mounted within a specially constructed open port cavity in the cabin of the aircraft and the second is mounted 6 meters away on top of the inboard port side (number 2) engine pylon. Three co-aligned laser beams are reflected between the two mirrors 64 times in a Herriott pattern. The resulting sample path length of 384 meters is used to perform a spectral absorption analysis of the airflow between the mirrors. To compensate for normal wing movement and engine oscillations both mirrors were designed as continuously driven mechanisms to maintain alignment within allowable limits. The motion systems of the two mirror assemblies provide five degrees of freedom and are designed to maintain a pointing accuracy within seven arc-sec with a response frequency in excess of 10 Hz. The pylon motion system incorporates controlled pitch and yaw movement. The fuselage motion system compensates for pitch variation as well as linear translation for focal length and vertical aiming of the laser beam via a controlled beam guidance mechanism.

Graham, Michael↗
NASA NTRS1998

Development of a Mirror Pointing Mechanism for an Atmospheric Gas Measurement Instrument

Development of the Open Path Tunable Infrared Monitor of the Atmosphere (OPTIMA) instrument involved designing a pair of motion systems that could maintain a precise alignment and spatial distance between two mirrors installed on the NASA DC-8 research laboratory aircraft. This is the first airborne optical instrument that allows direct measurement of the gases in the freestream airflow on the exterior of the aircraft. One mirror is mounted within a specially constructed open port cavity in the cabin of the aircraft and the second is mounted 6 meters away on top of the inboard port side (number 2) engine pylon. Three co-aligned laser beams are reflected between the two mirrors 64 times in a Herriott pattern. The resulting sample path length of 384 meters is used to perform a spectral absorption analysis of the airflow between the mirrors. To compensate for normal wing movement and engine oscillations both mirrors were designed as continuously driven mechanisms to maintain alignment within allowable limits. The motion systems of the two mirror assemblies provide five degrees of freedom and are designed to maintain a pointing accuracy within seven arc-sec with a response frequency in 6xcess of 10 Hz. The pylon motion system incorporates controlled pitch and yaw movement. The fuselage motion system compensates for pitch variation as well as linear translation for focal length and vertical aiming of the laser beam via a controlled beam guidance mechanism.

Graham, Michael↗
NASA NTRS1993

Flight investigation of the effect of tail boom strakes on helicopter directional control

A joint U.S. Army/NASA flight investigation was conducted utilizing a single-rotor helicopter to determine the effectiveness of horizontally mounted tail boom strakes on directional controllability and tail rotor power during low-speed, crosswind operating conditions. Three configurations were investigated: (1) baseline (strakes off), (2) single strake (strake at upper shoulder on port side of boom), and (3) double strake (upper strake plus a lower strake on same side of boom). The strakes were employed as a means to separate airflow over the tail boom and change fuselage yawing moments in a direction to improve the yaw control margin and reduce tail rotor power. Crosswind data were obtained in 5-knot increments of airspeed from 0 to 35 knots and in 30 deg increments of wind azimuth from 0 deg to 330 deg. At the most critical wind azimuth and airspeed in terms of tail rotor power, the strakes improved the pedal margin by 6 percent of total travel and reduced tail rotor power required by 17 percent. The increase in yaw control and reduction in tail rotor power offered by the strakes can expand the helicopter operating envelope in terms of gross weight and altitude capability. The strakes did not affect the flying qualities of the vehicle at airspeeds between 35 and 100 knots.

Kelly, Henry L.↗
NASA NTRS1984

Airflow Assists Solar Receiver

Heat loss by convection reduced. Simplified solar receiver concept involves inwardly directed flow of cooling air and "air door" to reduce loss by convection. Receiver is constructed from inexpensive materials.

Revere, W. R.↗
NASA NTRS1975

Study of a porous surface microphone sensor in an aerofoil

The porous microphone in an airfoil is described as a directional sensor which rejects flow noise. The airfoil allows the sensor to be rotated in the airflow over a wide range of yaw angles, 0 to 90 degrees, avoiding flow separation over the surface of the sensor and its associated additional flow noise. The microphone is discussed in terms of its acoustic properties, vibration sensitivity, effect of Mach number on the directivity function, and flow noise. Additional information on the acoustic calibration of the microphone, the acceleration sensitivity of the airfoil, stationary source and receiver in a moving gas, acoustic tests in airflow, and flow noise tests of the airfoil porous surface sensor is included.

Noiseux, D. U.↗
NASA NTRS2010

A Capillary-Based Static Phase Separator for Highly Variable Wetting Conditions

The invention, a static phase separator (SPS), uses airflow and capillary wetting characteristics to passively separate a two-phase (liquid and air) flow. The device accommodates highly variable liquid wetting characteristics. The resultant design allows for a range of wetting properties from about 0 to over 90 advancing contact angle, with frequent complete separation of liquid from gas observed when using appropriately scaled test conditions. Additionally, the design accommodates a range of air-to-liquid flow-rate ratios from only liquid flow to over 200:1 air-to-liquid flow rate. The SPS uses a helix input section with an ice-cream-cone-shaped constant area cross section (see figure). The wedge portion of the cross section is on the outer edge of the helix, and collects the liquid via centripetal acceleration. The helix then passes into an increasing cross-sectional area vane region. The liquid in the helix wedge is directed into the top of capillary wedges in the liquid containment section. The transition from diffuser to containment section includes a 90 change in capillary pumping direction, while maintaining inertial direction. This serves to impinge the liquid into the two off-center symmetrical vanes by the airflow. Rather than the airflow serving to shear liquid away from the capillary vanes, the design allows for further penetration of the liquid into the vanes by the air shear. This is also assisted by locating the air exit ports downstream of the liquid drain port. Additionally, any droplets not contained in the capillary vanes are re-entrained downstream by a third opposing capillary vane, which directs liquid back toward the liquid drain port. Finally, the dual air exit ports serve to slow the airflow down, and to reduce the likelihood of shear. The ports are stove-piped into the cavity to form an unfriendly capillary surface for a wetting fluid to carryover. The liquid drain port is located at the start of the containment region, allowing for draining the bulk fluid in a continuous circuit. The functional operation of the SPS involves introducing liquid flow (from a human body, a syringe, or other source) to the two-phase inlet while an air fan pulls on the air exit lines. The fan is operated until the liquid is fully introduced. The system is drained by negative pressure on the liquid drain lines when the SPS containment system is full.

Thomas, Evan A.↗