Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “diameter distribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Particulate Characteristics for Varying Engine Operation in a Gasoline Spark Ignited, Direct Injection Engine

The objective of this research is a detailed investigation of particulate sizing and number count from a direct-injection spark-ignited (DISI) engine at different operating conditions. The engine is a 549 [cc] single-cylinder, four valve engine with a flat-top piston, fueled by Tier II EEE. A baseline engine operating condition, with a low number of particulates, was established and repeatability at this condition was ascertained. This baseline condition is specified as 2000 rpm, 320 kPa IMEP, 280 [°bTDC] end of injection (EOI), and 25 [°bTDC] ignition timing. The particle size distributions were recorded for particle sizes between 7 and 289 [nm]. The baseline particle size distribution was relatively flat, around 1E6 [dN/dlogDp], for particle diameters between 7 and 100 [nm], before dropping off to decreasing numbers at larger diameters. Distributions resulting from a matrix of different engine conditions were recorded. These varied parameters include load, air-to-fuel ratio (A/F), spark timing, injection timing, fuel rail pressure, and oil and coolant temperatures. Most conditions resulted with uni-modal type distributions usually with an increase in magnitude of particles in comparison to the baseline, with the exception of lean operation with retarded ignition timing. Further investigation revealed high sensitivity of the particle number and size distribution to changes in the engine control parameters. There was also a high sensitivity of the particle size distributions to small variations in A/F, ignition timing, and EOI. Investigations revealed the possibility of emissions oxidation in the exhaust and engine combustion instability at later EOI timings which therefore ruled out late EOI as the benchmark condition. Attempts to develop this benchmark revealed engine sensitivity to A/F and ignition timing, especially at later EOI operation

Environmental Molecular Sciences Laboratory↗

Processing of alnico permanent magnets by advanced directional solidification methods

Advanced directional solidification methods have been used to produce large (>15 cm length) castings of Alnico permanent magnets with highly oriented columnar microstructures. In combination with subsequent thermomagnetic and draw thermal treatment, this method was used to enable the high coercivity, high-Titanium Alnico composition of 39% Co, 29.5% Fe, 14% Ni, 7.5% Ti, 7% Al, 3% Cu (wt%) to have an intrinsic coercivity (H ci ) of 2.0 kOe, a remanence (B r ) of 10.2 kG, and an energy product (BH) max of 10.9 MGOe. These properties compare favorably to typical properties for the commercial Alnico 9. Directional solidification of higher Ti compositions yielded anisotropic columnar grained microstructures if high heat extraction rates through the mold surface of at least 200 kW/m 2 were attained. This was achieved through the use of a thin walled (5 mm thick) high thermal conductivity SiC shell mold extracted from a molten Sn bath at a withdrawal rate of at least 200 mm/h. However, higher Ti compositions did not result in further increases in magnet performance. Images of the microstructures collected by scanning electron microscopy (SEM) reveal a majority α phase with inclusions of secondary αγ phase. Transmission electron microscopy (TEM) reveals that the α phase has a spinodally decomposed microstructure of FeCo-rich needles in a NiAl-rich matrix. In the 7.5% Ti composition the diameter distribution of the FeCo needles was bimodal with the majority having diameters of approximately 50 nm with a small fraction having diameters of approximately 10 nm. The needles formed a mosaic pattern and were elongated along one <001> crystal direction (parallel to the field used during magnetic annealing). Cu precipitates were observed between the needles. Regions of abnormal spinodal morphology appeared to correlate with secondary phase precipitates. The presence of these abnormalities did not prevent the material from displaying superior magnetic properties in the 7.5% Ti composition. As a result, higher Ti compositions did not display the preferred spinodal microstructure, explaining their inferior magnetic properties.

36 MATERIALS SCIENCE↗

Investigations on the droplet distributions in the atomization of kerosene jets in supersonic crossflows

Phase Doppler anemometry was applied to investigate the atomization processes of a kerosene jet injected into Ma = 1.86 crossflow. Physical behaviors, such as breakup and coalescence, are reproduced through the analysis of the spatial distribution of kerosene droplets' size. It is concluded that Sauter mean diameter distribution shape transforms into “I” type from “C” type as the atomization development. Simultaneously, the breakup of large droplets and the coalescence of small droplets can be observed throughout the whole atomization process.

42 ENGINEERING↗

Optical Plasma Control During ARC Carbon Nanotube Growth

To improve nanotube production, we developed a novel optical control technique, based on the shape of the visible plasma zone created between the anode and the cathode in the direct current (DC) arc process. For a given inert gas, we adjust the anode to cathode distance (ACD) in order to obtain strong visible vortices around the cathode. This enhance anode vaporization, which improve nanotubes formation. In light of our experimental results, we focus our discussion on the relationship between plasma parameters and nanotube growth. Plasma temperature control during arc process is achieved using argon, helium, and their mixtures as a buffer gases. The variation of the gas mixture from pure argon to pure helium changes plasma temperature. As a consequence, the microscopic characteristics of nanotubes as diameter distribution is changed moving from smaller values for argon to higher diameters for helium. We also observe a dependence of the macroscopic characteristics of the final products as Brunauer-Emmett-Teller (BET) surface area.

Hinkov, I.↗

Effect of Enhanced Thermal Stability of Alumina Support Layer on Growth of Vertically Aligned Single-Walled Carbon Nanotubes and Their Application in Nanofiltration Membranes

We investigate the thermal stability of alumina supporting layers sputtered at different conditions and its effect on the growth of aligned single-walled carbon nanotube arrays. Radio frequency magnetron sputtering of alumina under oxygen–argon atmosphere produces a Si-rich alumina alloy film on a silicon substrate. Atomic force microscopy on the annealed catalysts reveals that Si-rich alumina films are more stable than alumina layers with low Si content at the elevated temperatures at which the growth of single-walled carbon nanotubes is initiated. The enhanced thermal stability of the Si-rich alumina layer results in a narrower (< 2.2 nm) diameter distribution of the single-walled carbon nanotubes. Thanks to the smaller diameters of their nanotube pores, membranes fabricated with vertically aligned nanotubes grown on the stable layers display improved ion selectivity.

36 MATERIALS SCIENCE↗

Growth of single and double walled carbon nanotubes over Co/V/MgO catalysts

Highlights: {yields} Co/V/MgO has remarkable catalytic activity on the growth of SWCNTs and DWCNTs. {yields} The diameter of CNTs can be controlled by adjusting molar ratio of Co-V to MgO. {yields} The formation of C{sub 7}V{sub 8} is critical to the synthesis of thin CNTs. -- Abstract: High quality single walled carbon nanotubes (SWCNTs) and double walled carbon nanotubes (DWCNTs) were synthesized on Co/V/MgO catalysts by catalytic decomposition of CH{sub 4} in H{sub 2}. Raman spectroscopy data revealed that the diameters of as-prepared SWCNTs are 1.28 and 0.73 nm. The diameter value of DWCNTs from Raman analysis also showed a narrow diameter distribution. Using field emission transmission electron microscopy (TEM), it was found that the diameter of carbon nanotubes can be controlled mainly by adjusting the molar ratio of Co-V versus the MgO support. The structure properties of catalysts were examined by X-ray diffraction (XRD). The formation of C{sub 7}V{sub 8} may play an important role in preserving carbon in the catalyst particle and favoring the dissociation balance of CH{sub 4}.

36 MATERIALS SCIENCE↗

Review of Laser Ablation Process for Single Wall Carbon Nanotube Production

Different types of lasers are now routinely used to prepare single wall carbon nanotubes (SWCNTs). The original method developed by researchers at Rice University utilized a "double pulse laser oven" process. A graphite target containing about 1 atomic percent of metal catalysts is ablated inside a 1473K oven using laser pulses (10 ns pulse width) in slow flowing argon. Two YAG lasers with a green pulse (532 nm) followed by an IR pulse (1064 nm) with a 50 ns delay are used for ablation. This set up produced single wall carbon nanotube material with about 70% purity having a diameter distribution peaked around 1.4 nm. The impurities consist of fullerenes, metal catalyst clusters (10 to 100 nm diameter) and amorphous carbon. The rate of production with the initial set up was about 60 mg per hour with 10Hz laser systems. Several researchers have used variations of the lasers to improve the rate, consistency and study effects of different process parameters on the quality and quantity of SWCNTs. These variations include one to three YAG laser systems (Green, Green and IR), different pulse widths (nano to microseconds as well as continuous) and different laser wavelengths (Alexandrite, CO, CO2, free electron lasers in the near to far infrared). It is noted that yield from the single laser (Green or IR) systems is only a fraction of the two laser systems. The yield seemed to scale up with the repetition rate of the laser systems (10 to 60 Hz) and depended on the beam uniformity and quality of the laser pulses. The shift to longer wavelength lasers (free electron, CO and CO2) did not improve the quality, but increased the rate of production because these lasers are either continuous (CW) or high repetition rate pulses (kHz to MHz). The average power and the peak power of the lasers seem to influence the yields. Very high peak powers (MegaWatts per square centimeter) are noted to increase ablation of bigger particles with reduced yields of SWCNTs. Increased average powers seem to help the conversion of the carbon from target into vapor phase to improve formation of nanotubes. The use of CW far infrared lasers reduced the need for the oven, at the expense of controlled ablation. Some of these variations are tried with different combinations and concentrations of metal catalysts (Nickel with Cobalt, Iron, Palladium and Platinum) different buffer gases (e.g. Helium); with different oven temperatures (Room temperature to 1473K); under different flow conditions (1 to 1000 kPa) and even different porosities of the graphite targets. It is to be noted that the original Cobalt and Nickel combination worked best, possibly because of improved carbonization with stable crystalline phases. The mean diameter and yield seemed to increase with increasing oven temperatures. Thermal conductivity of the buffer gas and flow conditions dictate the quality as well as quantity of the SWCNTs. Faster flows, lower pressures and heavier gases seem to increase the yields. This review will attempt to cover all these variations and their relative merits. Possible growth mechanisms under these different conditions will also be discussed.

Arepalli, Sivaram↗

One-Step Synthesis of Zeolite Membranes Containing Catalytic Metal Nanoclusters

Metal-loaded zeolitic membranes are promising candidates as catalytic membrane reactors. We report a one-step synthesis method to synthesize zeolite membranes containing metal nanoclusters, that has advantages in comparison to multistep methods such as impregnation and ion exchange. Pure-silica MFI zeolite-Pt hybrid membranes were prepared by hydrothermal synthesis with addition of 3-mercaptopropyl-trimethoxysilane (MPS) and a platinum precursor. Composition analysis and mapping by energy-dispersive X-ray spectroscopy (EDX) reveal that Pt ions/clusters are uniformly distributed along the membrane cross-section. High-magnification scanning transmission electron microscopy (STEM) analysis shows that Pt metal clusters in the hybrid zeolite membrane have a diameter distribution in the range of 0.5–2.0 nm. In contrast, a pure-silica MFI membrane synthesized from an MPS-free solution shows negligible incorporation of Pt metal clusters. To characterize the properties of the hybrid (zeolite/metal) membrane, it was used as a catalytic membrane reactor (CMR) for high-temperature propane dehydrogenation (PDH) at 600 °C and 1 atm. The results indicate that Pt metal clusters formed within the MFI zeolite membrane can serve as effective catalysts for high-temperature PDH reaction along with H 2 removal via membrane permeation, thereby increasing both conversion and selectivity in relation to a conventional membrane reactor containing an equivalent amount of packed Pt catalyst in contact with an MFI membrane. In conclusion, the hybrid zeolite-Pt CMR also showed stable conversion and selectivity upon extended high-temperature operation (12 h), indicating that encapsulation in the zeolite allowed thermal stabilization of the Pt nanoclusters and reduced catalyst deactivation.

36 MATERIALS SCIENCE↗

Effect of liquid droplets on turbulence structure in a round gaseous jet

A proposed two equation turbulence model for incompressible dilute two phase flows was validated and extended for steady incompressible two phase flow including phase change. The model was tested for the flow of a turbulent axisymmetric gaseous jet laden with multisize evaporating liquid droplets. Predicted results include distributions of the mean velocity; volume fractions of different phases concentration of the evaporated material in the carrier phase; turbulence intensity and shear stress of the carrier phase; droplet diameter distribution; and the jet spreading rate. Results are analyzed based on a qualitative comparison with the corresponding single phase jet flow.

Mostafa, A. M.↗

Effect of liquid droplets on turbulence in a round gaseous jet

The main objective of this investigation is to develop a two-equation turbulence model for dilute vaporizing sprays or in general for dispersed two-phase flows including the effects of phase changes. The model that accounts for the interaction between the two phases is based on rigorously derived equations for turbulence kinetic energy (K) and its dissipation rate epsilon of the carrier phase using the momentum equation of that phase. Closure is achieved by modeling the turbulent correlations, up to third order, in the equations of the mean motion, concentration of the vapor in the carrier phase, and the kinetic energy of turbulence and its dissipation rate for the carrier phase. The governing equations are presented in both the exact and the modeled formes. The governing equations are solved numerically using a finite-difference procedure to test the presented model for the flow of a turbulent axisymmetric gaseous jet laden with either evaporating liquid droplets or solid particles. The predictions include the distribution of the mean velocity, volume fractions of the different phases, concentration of the evaporated material in the carrier phase, turbulence intensity and shear stress of the carrier phase, droplet diameter distribution, and the jet spreading rate. The predictions are in good agreement with the experimental data.

Mostafa, A. A.↗

Investigation of turbulent inflow specification in Euler–Lagrange simulations of mid-field spray

The process of atomization of a liquid jet by a parallel high-speed gas stream results in a spray, whose downstream development is of considerable interest to several applications. The round jet spray can be spatially divided into (i) a near-field (near-nozzle) region of liquid atomization and (ii) a downstream mid-field region of fully-dispersed droplets. In order to accurately model mid-field droplet dispersion, this work aims at developing a rigorous and robust injection model for Euler–Lagrange spray simulations. Results from experiments are used to obtain the relevant droplet number density, size distribution, and mean and standard deviation velocity distributions of the injection model, systematically in a step-by-step process. Two-phase large eddy simulations are performed by stochastically generating the Lagrangian droplets at the inlet of the mid-field region. Number flux, diameter distribution, mean velocity, and other time-averaged statistics at several downstream locations are shown to agree well with the corresponding experimental data.

42 ENGINEERING↗

Morphology and properties of a hybrid organic-inorganic system: Al nanoparticles embedded into CuPc thin film

The evolution of the morphology and the electronic structure of the hybrid organic-inorganic system composed of aluminum nanoparticles (NPs) distributed in an organic semiconductor matrix—copper phthalocyanine (CuPc)—as a function of nominal aluminum content was studied by transmission electron microscopy and by photoemission spectroscopy methods. The aluminum atoms deposited onto the CuPc surface diffuse into the organic matrix and self-assemble to NPs in a well-defined manner with a narrow diameter distribution, which depends on the amount of aluminum that is evaporated onto the CuPc film. We find clear evidence of a charge transfer from Al to CuPc and we have been able to determine the lattice sites where Al ions sit. The finally at high coverage about 64 Å the formation of metallic aluminum overlayer on CuPc thin film takes place.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Novel pore size-controlled, susceptibility matched, 3D-printed MRI phantoms

We report the design concept and fabrication of MRI phantoms, containing blocks of aligned microcapillaires that can be stacked into larger arrays to construct diameter distribution phantoms or fractured, to create a “powder-averaged” emulsion of randomly oriented blocks for vetting or calibrating advanced MRI methods, that is, diffusion tensor imaging, AxCaliber MRI, MAP-MRI, and multiple pulsed field gradient or double diffusion-encoded microstructure imaging methods. The goal was to create a susceptibility-matched microscopically anisotropic but macroscopically isotropic phantom with a ground truth diameter that could be used to vet advanced diffusion methods for diameter determination in fibrous tissues. Two-photon polymerization, a novel three-dimensional printing method is used to fabricate blocks of capillaries. Double diffusion encoding methods were employed and analyzed to estimate the expected MRI diameter. Susceptibility-matched microcapillary blocks or modules that can be assembled into large-scale MRI phantoms have been fabricated and measured using advanced diffusion methods, resulting in microscopic anisotropy and random orientation. This phantom can vet and calibrate various advanced MRI methods and multiple pulsed field gradient or diffusion-encoded microstructure imaging methods. We demonstrated that two double diffusion encoding methods underestimated the ground truth diameter.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Intrinsic Performance Variability in Aligned Array CNFETs

Here, the I-V characteristic of carbon nanotube (CNT) transistors is dictated by the Schottky barrier (SB) at metal-nanotube interface. The SB is defined by the diameter of the CNT along with the source/drain metal and is presumed a device constant for single CNT transistors. Given the wide distribution of diameter of CVD-grown nanotubes, the presumption of single SB, however, is inappropriate for transistors with aligned array of CNTs. Indeed, array transistors with similar geometries and contact material can still exhibit considerable variation in threshold voltage (V T ), on current (I ON ), and device resistance (R d ). We use measured diameter distribution within the framework of detailed numerical simulations to demonstrate that the diameter distribution of CNTs (in CNT FETs) plays a dominant role in defining the fluctuation of array transistors. Besides, it is argued that the large-scale integration of these devices within an IC would be feasible only if the distribution of diameter is considerably narrowed.

42 ENGINEERING↗

Orientational Growth of Carbon Nanotube for Applications

Since the superior properties of multi-wall carbon nanotubes (MWCNT) could improve numerous devices such as electronics and sensors, many efforts have been made in investigating the growth mechanism of MWCNT to synthesize high quality MWCNT. Most applications require uniform aligned CNT. In this presentation, a directional growth of CNT will be reported. Carbon nanotubes are synthesized using thermal chemical vapor deposition. Temperature and pressure are two important growth parameters for fabricating carbon nanotubes. It is found that the nanotube diameter distribution mainly depends on the growth-temperature. With the substrate surface normal either along or against the gravity vector, different growth orientations of MWCNT are observed by scanning electron microscopy although the Raman spectra are similar for samples synthesized at different locations. The sizes of these carbon nanotubes in each sample are quite uniform and the length of the tube is up to several tens of micrometers. These results suggest the gravitation effects in the growth of long and small diameter CNT.

Zhu, Shen↗

High-Performance Hemofiltration via Molecular Sieving and Ultra-Low Friction in Carbon Nanotube Capillary Membranes

Conventional dialyzer membranes typically comprise of unevenly distributed polydisperse, tortuous, rough pores, embedded in relatively thick ≈20–50 µm polymer layers wherein separation occurs via size exclusion as well as differences in diffusivity of the permeating species. However, transport in such polymeric pores is increasingly hindered as the molecule size approaches the pore dimension, resulting in significant retention of undesirable middle molecules (≥15–60 kDa) and uremic toxins. Enhanced removal of middle molecules is usually accompanied by high albumin loss (≈66 kDa) causing hypoalbuminemia. Here, the scalable bottom-up fabrication of wafer-scale carbon nanotube (CNT) membranes with highly aligned, low-friction, straight-channels/capillaries and narrow pore-diameter distributions (≈0.5–4.5 nm) is demonstrated, to overcome persistent challenges in hemofiltration/hemodialysis. Using fluorescein isothiocyanate (FITC)-Ficoll 70 and albumin in phosphate buffered saline (PBS) as well as in bovine blood plasma, it is shown that CNT membranes can allow for significantly higher hydraulic permeability (more than an order of magnitude when normalized to pore area) than commercial high-flux hemofiltration/hemodialysis membranes (HF 400), as well as greatly enhance removal of middle molecules while maintaining comparable albumin retention. These findings are rationalized via an N-pore transport model that highlights the critical role of molecular flexing and deformation during size-selective transport within nanoscale confinements of the CNTs. In conclusion, the unique transport characteristics of CNTs coupled with size-exclusion and wafer-scale fabrication offer transformative advances for hemofiltration, and the obtained insight into molecular transport can aid advancements in several other bio-systems/applications beyond hemofiltration/hemodialysis.

36 MATERIALS SCIENCE↗