Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “design constraints”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Synthetic aperture radar range - Azimuth ambiguity design and constraints

Problems concerning the design of a system for mapping a planetary surface with a synthetic aperture radar (SAR) are considered. Given an ambiguity level, resolution, and swath width, the problems are related to the determination of optimum antenna apertures and the most suitable pulse repetition frequency (PRF). From the set of normalized azimuth ambiguity ratio curves, the designer can arrive at the azimuth antenna length, and from the sets of normalized range ambiguity ratio curves, he can arrive at the range aperture length or pulse repetition frequency. A procedure based on this design method is shown in an example. The normalized curves provide results for a SAR using a uniformly or cosine weighted rectangular antenna aperture.

Mehlis, J. G.↗
NASA NTRS1973

Apollo experience report: Guidance and control systems - Digital autopilot design development

The development of the Apollo digital autopilots (the primary attitude control systems that were used for all phases of the lunar landing mission) is summarized. This report includes design requirements, design constraints, and design philosophy. The development-process functions and the essential information flow paths are identified. Specific problem areas that existed during the development are included. A discussion is also presented on the benefits inherent in mechanizing attitude-controller logic and dynamic compensation in a digital computer.

Peters, W. H.↗
NASA NTRSDate not supplied

Development of an Ejectable Data Recorder Ejection Mechanism for the Low Earth Orbit Flight Test of an Inflatable Decelerator

On November 10, 2022, the 1100kg (2,425 lbs.) LOFTID Reentry Vehicle (RV) was launched on a United Launch Alliance Atlas V as a secondary payload with the Joint Polar Surveyor System-2. The 6-meter diameter (~20 ft.) aeroshell (a type of heat shield) entered the atmosphere at 8 kilometers per second (18,000 miles per hour), and flew nominally, enduring the intended heat pulse that saw temperatures exceeding 1371˚C (2500˚F) on the front side while the payload skin remained only about 38˚C (100˚F). The RV exceeded Mach 30 and the heat-affected aeroshell withstood a pressure pulse that exerted 9g’s deceleration maintaining stable flight through the hypersonic, supersonic, transonic, and subsonic regimes to the parachute deployment. As part of the Agency’s strategic goal “to extend human presence deeper into space and to the moon for sustainable long-term exploration and utilization”, the LOFTID inflatable aerodynamic decelerator or aeroshell technology could one day help land humans on Mars. As with any flight test, data collection is of utmost importance. Without a data downlink and a possibility of the RV sinking before the recovery crew got to it, a secondary data collection method was introduced. The RV would eject a data recorder, which would have a duplicate copy of the on-board flight date, before splashdown and be retrieved separately. This paper discusses the development of the ejection mechanism used to eject the data recorder from the RV during the test flight. The development includes discussions of design constraints, a design overview, the testing program, and lessons learned throughout the process all the way through successful data recorder recovery.

mechanism↗
NASA NTRS1985

Generative engineering databases - Toward expert systems

Engineering data management, incorporating concepts of optimization with data representation, is receiving increasing attention as the amount and complexity of information necessary for performing engineering operations increases and the need to coordinate its representation and use increases. Research in this area promises advantages for a wide variety of engineering applications, particularly those which seek to use data in innovative ways in the engineering process. This paper presents a framework for a comprehensive, relational database management system that combines a knowledge base of design constraints with a database of engineering data items in order to achieve a 'generative database' - one which automatically generates new engineering design data according to the design constraints stored in the knowledge base. The representation requires a database that is able to store all of the data normally associated with engineering design and to accurately represent the interactions between constraints and the stored data while guaranteeing its integrity. The representation also requires a knowledge base that is able to store all the constraints imposed upon the engineering design process.

Rasdorf, W. J.↗
NASA NTRS1989

A second-generation supersonic transport

Ever since the advent of commercial flight vehicles, one goal of designers has been to develop aircraft that can fly faster and carry more passengers than before. After the development of practical supersonic military aircraft, this desire was naturally manifested in a search for a practical supersonic commercial aircraft. The first and, to date, only supersonic civil transport is the Concorde, manufactured by a consortium of British and French aerospace companies. Unfortunately, due to a number of factors, including low passenger capacity and limited range, the Concorde has not been an economic success. It is for this reason that there is considerable interest in developing a design for a supersonic civil transport that addresses some of the inadequacies of the Concorde. For the design of such an aircraft to be feasible in the near term, certain guidelines must be established at the outset. Based upon the experience with the Concorde, whose 100- passenger capacity is not large enough for profitable operation, a minimum capacity of 250 passengers is desired. Second, to date, because of the limited range of the Concorde, supersonic commercial flight has been restricted to trans-Atlantic routes. In order to broaden the potential market, any new design must have the capability of trans-Pacific flight. A summary of the potential markets involved is presented in Fig. 1. Also, because of both the cost and complexity involved with actively cooling an entire aircraft, an additional design constraint is that the aircraft as a whole be passively cooled. One additional design constraint is somewhat less quantitative in nature but of great importance nonetheless. Any time a new design is attempted, the tendency is to assume great strides in technology that serve as the basis for actual realization of the design. While it is not always possible to avoid this dependence on "enabling technology," since this design is desired for the near term, it is prudent, wherever possible, to rely on already existing technology. This is of particular importance with respect to support technology such as airport terminals and runways. Based on the above introductory remarks, a possible approach to the design of a second-generation supersonic civil transport is presented below. The design Mach number for this aircraft is 3.5. This value was chosen as it represents the limiting Mach number in the absence of active cooling. The ensuing design attempts to deal with the particular problems that are the most demanding, while relying on proven technology where it is adequate. The report clearly does not solve, or even deal with, every aspect of the aircraft design. Rather, a general direction is suggested and supported with initial, approximate calculations.

W. Humphrey↗
NASA NTRS1975

Conceptual engineering design studies of 1985-era commercial VTOL and STOL transports that utilize rotors

Conceptual design studies are summarized of tandem-rotor helicopter and tilt-rotor aircraft for a short haul transport mission in the 1985 time frame. Vertical takeoff designs of both configurations are discussed, and the impact of external noise criteria on the vehicle designs, performance, and costs are shown. A STOL design for the tilt-rotor configuration is reported, and the effect of removing the vertical takeoff design constraints on the design parameters, fuel economy, and operating cost is discussed.

Magee, J. P.↗
NASA NTRS1987

Design of a neural network simulator on a transputer array

A brief summary of neural networks is presented which concentrates on the design constraints imposed. Major design issues are discussed together with analysis methods and the chosen solutions. Although the system will be capable of running on most transputer architectures, it currently is being implemented on a 40-transputer system connected to a toroidal architecture. Predictions show a performance level equivalent to that of a highly optimized simulator running on the SX-2 supercomputer.

Mcintire, Gary↗
NASA NTRS1986

Optimization of Antenna-Structure Design

Conference paper describes application of optimality criterion to design of microwave dish antenna. For purpose of study, overall design objective is to minimize structural weight, subject to design constraints that antenna-pointing and microwave-path-length errors not exceed specified values. Design constraints and optimality criterion satisfied in same procedure.

Levy, R.↗
NASA NTRS1985

Liquid droplet radiator technology issues

The operation of the liquid droplet radiator (LDR) is analyzed to establish design constraints for the LDR components and to predict the performance of an integrated LDR system. The design constraints largely result from mass loss considerations: fluid choice is governed by evaporation loss; droplet generation techniques must be capable of precise aiming of greater than 10 to the 5th droplet streams; and collection losses must be less than 1 droplet in 10 to the 7th. Concepts for droplet generation and collection components are discussed and incorporated into a mass model for an LDR system. This model predicts that LDR's using lithium, Dow 705 silicone fluid, or NaK may be several times lighter than heat pipe radiators.

Mattick, A. T.↗
NASA NTRS1987

Development of wing and tail configurations for low altitude unmanned research aircraft (LAURA)

The Low Altitude/Airspeed Unmanned Research Aircraft (LAURA) is being developed by the U.S. Navy for flight test research using low-Reynolds number airfoils. This vehicle consists of a standard modular fuselage designed to accept the installation of several wings/tails having low Reynolds number airfoils, and various planform shapes. Design constraints include shipboard storage, long flight endurance at very low airspeeds and sea-skimming cruise altitude. The stringent design constraints require the development of high-performance low Reynolds number (LRN) airfoils, suitable lifting surface configuration, and advanced airframe-propulsion systems. The present paper describes ongoing efforts to develop wing and tail configurations for LAURA using airfoils designed at NASA Langley Research Center.

Mangalam, S. M.↗
NASA NTRS1990

Stacking optimization of compressor blades of gas turbine engines

A procedure is presented to obtain optimal designs of axial compressor blades with structural design constraints. Coefficients of the polynomials defining the circumferential tilting angles and the axial leaning distances of the airfoil cross sections from the initial design geometry are used as design variables. The compressor blades are modeled by 20-node solid elements. An efficient finite element method is developed for modal analysis and sensitivity analysis with respect to the design variables. Based on this information, a sequential linear programming method is applied to calculate the required change of geometry for the desired structural design constraints.

Cheu, Tsu-Chien↗
NASA NTRS1993

Simplified, inverse, ejector design tool

A simple lumped parameter based inverse design tool has been developed which provides flow path geometry and entrainment estimates subject to operational, acoustic, and design constraints. These constraints are manifested through specification of primary mass flow rate or ejector thrust, fully-mixed exit velocity, and static pressure matching. Fundamentally, integral forms of the conservation equations coupled with the specified design constraints are combined to yield an easily invertible linear system in terms of the flow path cross-sectional areas. Entrainment is computed by back substitution. Initial comparison with experimental and analogous one-dimensional methods show good agreement. Thus, this simple inverse design code provides an analytically based, preliminary design tool with direct application to High Speed Civil Transport (HSCT) design studies.

Dechant, Lawrence J.↗
NASA NTRS1999

Landing Site Engineering Constraints

Based upon the lander design, constraints are placed upon the landing site selection process in order to mitigate landing risk and optimize mission performance. Constraints are placed on the landing site latitude, elevation, measured rock abundance and terrain slopes within the landing footprint. Estimated mission lifetime and power availability as a function of landing site latitude will be presented. The dimensions of the landing footprint will be given. Plans for obtaining high resolution MOC images of candidate landing sites will be discussed.

Spencer, D.↗
NASA NTRS1988

Structural tailoring of advanced turboprops

The Structural Tailoring of Advanced Turboprops (STAT) computer program was developed to perform numerical optimization on highly swept propfan blades. The optimization procedure seeks to minimize an objective function defined as either: (1) direct operating cost of full scale blade or, (2) aeroelastic differences between a blade and its scaled model, by tuning internal and external geometry variables that must satisfy realistic blade design constraints. The STAT analysis system includes an aerodynamic efficiency evaluation, a finite element stress and vibration analysis, an acoustic analysis, a flutter analysis, and a once-per-revolution forced response life prediction capability. STAT includes all relevant propfan design constraints.

Brown, K. W.↗
NASA NTRSDate not supplied

Lander Lighting Solution to Reduce Pilot & Autonomous Approach Errors

The south pole lighting environment will have harsh low inclination sunlight, making overhead judgement of surface features difficult. Autonomous solutions are great, however, the need for visual monitoring and independent go/no-go decisions remain. Our project proposes that lunar landing systems will be better served by including a powerful landing light system that improves visibility of surfaces from overhead by illuminating the ground at critical distances for the crew to make last minute decisions regarding an approach. The project utilized computer-based optical modeling software to predict requirements for a potential landing light system. The analysis based the lamp prediction from commercially available LED chip sets and lamp optics. The goal was to illustrate a method to raise the surface contrast of a landing site within an acceptable contrast threshold for most camera systems and human observers to recognize hazards that would not be noticed with low inclination sunlight alone. The Apollo lunar landings benefitted from overhead sun or dark conditions. The surface lighting at the Lunar South Pole is a harsh environment where surfaces are lit from a low inclination angle by the sun (from the side). This change in lighting condition precipitates a need for updated lunar landing systems that facilitate improved recognition of landing sites, and thereby increase pilot awareness of landing hazards. The reliance on LIDAR and other autonomous mechanisms alone is risky given the known usage of visual monitoring for operator concurrence on current spacecraft programs and present-day autonomous land-based vehicles. Visual monitoring via cameras or windows requires the surface contrast to be within 3 orders of magnitude for reasonable recognition of objects. Artificial overhead illumination, when sufficiently sized, provides a means to even out contrast problems created by low inclination sunlight, potentially reducing piloting errors. Current vehicle requirements do not specify this type of guidance for the purpose of increasing mission success. An optical ray-trace simulation model was developed in Zemax Optics Studio to predict the best combination of LED power, LED optics, lamp quantity, and lamp location to raise the surface contrast to within 2 orders of magnitude from 3 orders required to further increased visibility and reduce risk. The project considered the following design constraints: potential base diameter of lander, approach distance(s) for a go-no-go decision point (200 meter), solar inclination angle (2-7), lunar surface reflectance (10%), LED chip sets, LED focusing optics, LED power, lamp quantity, lamp locations, and illumination diameter of lunar surface landing zone. The results can be used to establish minimum design constraints for vehicle landing light systems. With a solar inclination angle ranging from 2-7 degrees, the horizontal illumination of the lunar surface is attenuated by about 10% when compared to overhead illumination from the Sun. This modifies the sun's maximum of 130,000 lux to 13,000 lux horizontal illuminance. The artificial lighting system was designed to provide an 18-meter-wide illumination zone, to create viewing clearances around a 6-meter-wide lander. The system provides an average illuminance of 300 lux, meeting the 2 orders of magnitude criteria. The solution utilized modern Chip On Board LEDs, that each utilized 17 watts, with focusing Total Internal Reflection (TIR) lenses. A lighting system of 300 LEDs was arrayed along the "bottom" of a “lander”. With 17 watts per LED, the system is estimated to require 5100 watts. This is a large amount of power, but it would only be needed during critical phases during the landing. LED lighting systems can be dimmed, and it is assumed that as the lander arrives closer to the landing site, the lighting system power can be adjusted as needed to produce the necessary surface illuminance. The designed reduction of contrast improves reliability of safety assessments using real time visible light camera systems and out the window viewing by the crew.

T A Clark↗
NASA NTRS1983

Parametric study of critical constraints for a canard configured medium range transport using conceptual design optimization

Constrained parameter optimization was used to perform optimal conceptual design of both canard and conventional configurations of a medium range transport. A number of design constants and design constraints were systematically varied to compare the sensitivities of canard and conventional configurations to a variety of technology assumptions. Main landing gear location and horizontal stabilizer high-lift performance were identified as critical design parameters for a statically stable, subsonic canard transport.

Arbuckle, P. D.↗
NASA NTRS1988

Control Augmented Structural Synthesis

A methodology for control augmented structural synthesis is proposed for a class of structures which can be modeled as an assemblage of frame and/or truss elements. It is assumed that both the plant (structure) and the active control system dynamics can be adequately represented with a linear model. The structural sizing variables, active control system feedback gains and nonstructural lumped masses are treated simultaneously as independent design variables. Design constraints are imposed on static and dynamic displacements, static stresses, actuator forces and natural frequencies to ensure acceptable system behavior. Multiple static and dynamic loading conditions are considered. Side constraints imposed on the design variables protect against the generation of unrealizable designs. While the proposed approach is fundamentally more general, here the methodology is developed and demonstrated for the case where: (1) the dynamic loading is harmonic and thus the steady state response is of primary interest; (2) direct output feedback is used for the control system model; and (3) the actuators and sensors are collocated.

Lust, Robert V.↗