SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Numerical calculation of the critical current through a Josephson junction interferometer, taking into consideration the effect of applied and self-induced magnetic fields on the junctions and in the interference loop. The periodicity of the interference pattern is shown to be less than the flux quantum. Quantitative results are given which illustrate the degree of deviation in periodicity from the flux quantum.
NASA Glenn Research Center is developing a 1.4~MW high-efficiency electric machine for future electrified aircraft to reduce energy consumption, emissions, and noise. This wound-field, synchronous machine employs a self-cooled, superconducting rotor to achieve excellent specific power and efficiency. This paper discusses the fabrication of the no-insulation high temperature superconducting (HTS) coils and presents the lessons learned. The process is compared to the fabrication of conventionally insulated HTS coils. Testing of the coils' critical current at liquid nitrogen temperature is also presented. The influence of thermal cycling on the critical current and n-value is studied.
In the Y-Ba-Cu-O system YBa2Cu3Ox phase is produced by the following peritectic reaction: Y2BaCuO5 + liquid yields 2YBa2Cu3Ox. Through the control of processing conditions and starting compositions it becomes possible to fabricate large crystals containing fine Y2BaCuO5(211) inclusions. Such crystals exhibit Jc values exceeding 10000 A/sq cm at 77 K and 1T. Recently, researchers developed a novel process which can control the volume fraction of 211 inclusions. Elimination of 211 inclusions is also possible. In this study, researchers prepared YBaCuO crystals with and without 211 inclusions using the novel process and compared flux pinning, flux creep and critical currents. Magnetic field dependence of Jc for YBaCuO crystals with and without 211 inclusions is shown. It is clear that fine 211 inclusions can contribute to flux pinning. It was also found that flux creep rate could be reduced by increasing flux pinning force. Critical current density estimates based on the conventional flux pinning theory were in good agreement with experimental results.
In the Y-Ba-Cu-O system, YBa2Cu3O(x) phase is produced by the following peritectic reaction: Y2BaCuO5 + liquid yields 2YBa2Cu3O(x). Through the control of processing conditions and starting compositions, it becomes possible to fabricate large crystals containing fine Y2BaCuO5(211) inclusions. Such crystals exhibit Jc values exceeding 10000 A/sq cm at 77 K and 1T. Recently, researchers developed a novel process which can control the volume fraction of 211 inclusions. Elimination of 211 inclusions is also possible. In this study, researchers prepared YBaCuO crystals with and without 211 inclusions using the novel process, and compared flux pinning, flux creep and critical currents. Magnetic field dependence of Jc for YBaCuO crystals with and with 211 inclusions is shown. It is clear that fine 211 inclusions can contribute to flux pinning. It was also found that flux creep rate could be reduced by increasing flux pinning force. Critical current density estimates based on the conventional flux pinning theory were in good agreement with experimental results.
Critical current studies have been made on copper-clad Nb-Ti composite wire prepared under area reductions of 100:1 and 10,000:1 by hydrostatic extrusion (HE), wire drawing and HE plus drawing. Comparative evaluation of the thermomechanical processing equivalent of HE was performed.
Anisotropy determination of critical current density in wide samples of strip semiconductors as function of magnetic field direction
Flux-flow resistivity and critical current density orientational dependence in Pb alloys type 2 superconducting foils under magnetic field, discussing Lorentz force
Niobium nitride thin films very high critical current and field characteristics, noting deposition by sputtering
Time linear increase of magnetic flux flow through superconducting Nb-Zr wall, inferring empirical critical current density model agreement with measured flow rate
The angular dependence of the critical current density and the magnetoresistance of high-T(sub c)-films in high and low magnetic fields and for different temperatures were measured to investigate the flux pinning and the superconducting properties. A comparison of the results for the different superconductors shows their increasing dependence on the angle Theta between the magnetic field and the c-axis of the film due to the anisotropy of the chosen superconductor. Furthermore the influence of the current direction to the Theta-rotation plane is discussed.
A study of irreversibility in the magnetization curves of Tl2Ba2Ca2Cu3O10 and Tl2Ba2Ca1Cu2O8 was undertaken to determine the intragranular critical currents and the effects of flux-creep in grain-aligned samples of these materials. For fields of greater than 0.3 T, and H parallel to c axis, the critical supercurrent falls approximately exponentially with both magnetic field and temperature. Flux-creep is found to be linear in the logarithm of time at low fields over a wide temperature range.
Epitaxial (Tl,Bi)Sr(1.6)Ba(0.4)Ca2Cu3O(x) ((Tl,Bi)-1223) thin films on (100) single crystal LaAlO3 substrates were synthesized by a two-step procedure. Phase development, microstructure, and relationships between film and substrate were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Resistance versus temperature, zero-field-cooled and field cooled magnetization, and transport critical current density (J(sub c)) were measured. The zero-resistance temperature was 105-111 K. J(sub c) at 77 K and zero field was greater than 2 x 10(exp 6) A/sq cm. The films exhibited good flux pinning properties.
The nonlinear current-voltage curves exhibited by tin films in the flux flow state have made studies of the amount of heating present in the sample necessary. The samples in this work consisted of an evaporated tin film on one side of a 2 mm thick crystal quartz substrate and a carbon film of the same configuration as the tin film on the back of the substrate. The carbon film was used as a thermometer to measure the temperature rise of the tin film above the bath temperature. The heating results indicate negligible effects in the samples. Temperature ratios as small as 0.80 for the tin samples have been investigated and the current-voltage characteristics are still nonlinear, indicating that the source of the nonlinearity is not Joule heating in the samples.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Spatial distributions of persistent magnetic field trapped by sintered and melt-textured ceramic-type high-temperature superconductor (HTS) samples have been studied. The trapped field can be reproduced by a model of the current consisting of two components: (1) a surface current Js and (2) a uniform volume current Jv. This Js + Jv model gives a satisfactory account of the spatial distribution of the magnetic field trapped by different types of HTS samples. The magnetic moment can be calculated, based on the Js + Jv model, and the result agrees well with that measured by standard vibrating sample magnetometer (VSM). As a consequence, Jc predicted by VSM methods agrees with Jc predicted from the Js + Jv model. The field mapping method described is also useful to reveal the granular structure of large HTS samples and regions of weak links.
No abstract available
Electric arc quenching at critical direct current values for circuits with inductive load