Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “corrected data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Surface Temperature Anomalies Derived from Night Time ASTER Data Corrected for Solar and Topographic Effects, Alamosa and Saguache Counties, Colorado

This map shows areas of anomalous surface temperature in Alamosa and Saguache Counties identified from ASTER thermal data and spatial based insolation model. The temperature is calculated using the Emissivity Normalization Algorithm that separate temperature from emissivity. The incoming solar radiation was calculated using spatial based insolation model developed by Fu and Rich (1999). Then the temperature due to solar radiation was calculated using emissivity derived from ASTER data. The residual temperature, i.e. temperature due to solar radiation subtracted from ASTER temperature was used to identify thermally anomalous areas. Areas that had temperature greater than 2o were considered ASTER modeled "very warm modeled surface temperature" are shown in red on the map. Areas that had temperatures between 1o and 2o were considered ASTER modeled "warm modeled surface temperature" are shown in yellow on the map. This map also includes the locations of shallow temperature survey points, locations of springs or wells with favorable geochemistry, faults, transmission lines, and areas of modeled basement weakness "fairways." Note: 'o' is used in this description to represent lowercase sigma.

15 GEOTHERMAL ENERGY↗

NSA AERI Hatch Correction Data Set

From 2000-2008, the NSA AERI hatch was determined to be indicated as open too frequently. Analysis suggests that the hatch was actually opening and closing properly but that its status was not being correctly reported by the hatch controller to the datastream. An algorithm was written to determine the hatch status from the observed

54 ENVIRONMENTAL SCIENCES↗

Machine Learning Techniques Applied to Sensor Data Correction in Building Technologies

Since commercial and residential buildings account for nearly half of the United States' energy consumption, making them more energy-efficient is a vital part of the nation's overall energy strategy. Sensors play an important role in this research by collecting data needed to analyze performance of components, systems, and whole-buildings. Given this reliance on sensors, ensuring that sensor data are valid is a crucial problem. Solutions being researched are machine learning techniques, namely: artificial neural networks and Bayesian Networks. Types of data investigated in this study are: (1) temperature; (2) humidity; (3) refrigerator energy consumption; (4) heat pump liquid pressure; and (5) water flow. These data are taken from Oak Ridge National Laboratory's (ORNL) ZEBRAlliance research project which is composed of four single-family homes in Oak Ridge, TN. Results show that for the temperature, humidity, pressure, and flow sensors, data can mostly be predicted with root-mean-square error (RMSE) of less than 10% of the respective sensor's mean value. Results for the energy sensor are not as good; RMSE are centered about 100% of the mean value and are often well above 200%. Bayesian networks have RSME of less than 5% of the respective sensor's mean value, but took substantially longer to train.

building technologies↗

DSS 43 antenna gain analysis for Voyager Uranus encounter: 8.45-GHz radio science data correction

A malfunction of the Deep Space Network (DSN) 64-meter antenna in Australia forced the antenna to operate with a mispositioned subreflector during the Voyager Uranus encounter period (January 24, 1986). Because of changing main reflector shape and quadripod position as a function of elevation angle, the antenna gain and pointing were not as expected, and the 8.45 GHz received signal level changed during the pass. The study described here used the Geometrical Theory of Diffraction (GTD) analysis to determine actual antenna gain and pointing during that period in an attempt to reconstruct the radio science data. It is found that the 1.4 dB of signal variation can be accounted for by antenna geometry changes and pointing error. Suggested modifications to the values measured during the pass are presented. Additionally, an extremely useful tool for the analysis of gravity deformed reflectors was developed for use in future antenna design and analysis projects.

Slobin, S. D.↗

Function minimization with partially correct data via simulated annealing

The simulated annealing technique has been applied successfully to the problem of estimating the coefficients of a function in cases where only a portion of the data being fitted to the function is truly representative of the function, the rest being erroneous. Two examples are given, one in photometric function fitting and the other in pattern recognition. A schematic of the algorithm is provided.

Lorre, Jean J.↗

En route noise: NASA propfan test aircraft (corrected data - simplified procedure)

Surface noise measurements were made during a joint National Aeronautics and Space Administration (NASA) and Federal Aviation Administration (FAA) program to study the high-altitude, low-frequency acoustic noise propagation characteristics of the Advanced Turboprop (propfan) Aircraft. The measurements were made on October 26-31, 1987 in Huntsville, Alabama and on April 3-13, 1989 at the White Sands Missile Range (WSMR), New Mexico. To effectively compare flight-to-flight data as received on the ground, the procedures and practices of Federal Air Regulation (FAR) Part 36 were used as a guide in adjusting the measured ground data at the time of LA(sub MAX) to a set of reference conditions. After the data for each event were processed using slow detector characteristics, the data record at LA(sub MAX) was then identified and the coordinates of the aircraft at the time of emission were calculated, taking into account atmospheric refraction effects. The effects of atmospheric absorption through the test day and reference day atmosphere were also taken into account and the 1/3-octave data were adjusted accordingly.

Rickley, E. J.↗

Wind-tunnel boundary interference for V/STOL TESTING

The wake skew angle used in applying the theory of NASA TR R-124 to data correction should be such that the angular deflection of the wake vorticity from the horizontal is one-half that calculated from momentum theory at the lifting element. This usage is in contrast to that of the original paper which used the angle of the mass flow. Because of large-scale recirculation effects, there is a finite lower limit to the test speed at which reliable and correctable data can be obtained in closed wind tunnels. Although a zero-correction wind tunnel for V/STOL testing has not yet been achieved, it is shown that the use of suitably mixed wind-tunnel boundaries can alleviate boundary effects on V/STOL data.

V/STOL AIRCRAFT↗

Measurement of Plutonium Ratios for CRM 137A Recertification

This report documents the analytical methodologies used by the Chemical and Isotopics Mass Spectrometry (CIMS) Group at the US Department of Energy’s Oak Ridge National Laboratory (ORNL) for plutonium isotopic ratio characterizations on purified ~1 mg units prepared by Lawrence Livermore National Laboratory (LLNL) from a mother solution created from an existing 250 mg unit of certified reference material (CRM) 137. The analytical processes described are designed to maintain traceability of the final certified attributes and to eliminate sources of systematic bias for the measurements described. The measurands for certification are the plutonium isotope ratios: 238 Pu/ 239 Pu, 240 Pu/ 239 Pu, 241 Pu/ 239 Pu, and 242 Pu/ 239 Pu. The preparation and analytical process included the following activities: Preparation of reference materials to be used as calibrants to establish traceability to the SI unit of mass for the isotopic analyses and quality controls. For the plutonium isotopic analyses, CRM 128 (a CRM comprising equal atoms of 239 Pu and 242 Pu) was used as the primary calibrant; Each CRM 137A unit was reconstituted using dilute high-purity HNO3. From each, seven replicates were distributed for the isotopic characterizations by thermal ionization mass spectrometry (TIMS) using the total evaporation (TE) method for isotope ratio measurements and MC-ICP-MS using a dynamic peak hooping method for secondary isotope ratio measurements; Due to time delay in the analyses from the last purification of the original CRM 137 mother solution by LLNL, an aliquot of the three provided plutonium units was purified using Eichrom TEVA separation methods to remove americium in-growth and uranium impurities; Minimally corrected data were reported from each analysis using reporting templates provided by the New Brunswick Laboratory Program Office (NBL PO) for the specific methods used for isotopic measurements. In addition, a copy of the instrument exports, Excel templates for isotopic data corrections, and the uncertainty budgets completed with the GUM Workbench software package were submitted to NBL PO.

07 ISOTOPE AND RADIATION SOURCES↗

DC-8 Scanning Lidar Characterization of Aircraft Contrails and Cirrus Clouds

An angular-scanning large-aperture (36 cm) backscatter lidar was developed and deployed on the NASA DC-8 research aircraft as part of the SUCCESS (Subsonic Aircraft: Contrail and Cloud Effects Special Study) program. The lidar viewing direction could be scanned continuously during aircraft flight from vertically upward to forward to vertically downward, or the viewing could be at fixed angles. Real-time pictorial displays generated from the lidar signatures were broadcast on the DC-8 video network and used to locate clouds and contrails above, ahead of, and below the DC-8 to depict their spatial structure and to help select DC-8 altitudes for achieving optimum sampling by onboard in situ sensors. Several lidar receiver systems and real-time data displays were evaluated to help extend in situ data into vertical dimensions and to help establish possible lidar configurations and applications on future missions. Digital lidar signatures were recorded on 8 mm Exabyte tape and generated real-time displays were recorded on 8mm video tape. The digital records were transcribed in a common format to compact disks to facilitate data analysis and delivery to SUCCESS participants. Data selected from the real-time display video recordings were processed for publication-quality displays incorporating several standard lidar data corrections. Data examples are presented that illustrate: (1) correlation with particulate, gas, and radiometric measurements made by onboard sensors, (2) discrimination and identification between contrails observed by onboard sensors, (3) high-altitude (13 km) scattering layer that exhibits greatly enhanced vertical backscatter relative to off-vertical backscatter, and (4) mapping of vertical distributions of individual precipitating ice crystals and their capture by cloud layers. An angular scan plotting program was developed that accounts for DC-8 pitch and velocity.

Uthe, Edward E.↗

An overview of the thematic mapper geometric correction system

Geometric accuracy specifications for LANDSAT 4 are reviewed and the processing concepts which form the basis of NASA's thematic mapper geometric correction system are summarized for both the flight and ground segments. The flight segment includes the thematic mapper instrument, attitude measurement devices, attitude control, and ephemeris processing. For geometric correction the ground segment uses mirror scan correction data, payload correction data, and control point information to determine where TM detector samples fall on output map projection systems. Then the raw imagery is reformatted and resampled to produce image samples on a selected output projection grid system.

Beyer, E. P.↗

LANDSAT-4 MSS Geometric Correction: Methods and Results

An automated image registration system such as that developed for LANDSAT-4 can produce all of the information needed to verify and calibrate the software and to evaluate system performance. The on-line MSS archive generation process which upgrades systematic correction data to geodetic correction data is described as well as the control point library build subsystem which generates control point chips and support data for on-line upgrade of correction data. The system performance was evaluated for both temporal and geodetic registration. For temporal registration, 90% errors were computed to be .36 IFOV (instantaneous field of view) = 82.7 meters) cross track, and .29 IFOV along track. Also, for actual production runs monitored, the 90% errors were .29 IFOV cross track and .25 IFOV along track. The system specification is .3 IFOV, 90% of the time, both cross and along track. For geodetic registration performance, the model bias was measured by designating control points in the geodetically corrected imagery.

Brooks, J.↗

SAIL-Net Raw and Post Corrected POPS Data Fall 2021 - Summer 2023

SAIL-Net is a DOE funded project in the East River Watershed near Crested Butte, Colorado with the goal of advancing our understanding of aerosol-cloud interactions in complex, mountainous regions. Through the deployment of a network of six low cost microphysics nodes in Fall 2021 in the same domain at the SAIL campaign, SAIL-Net provides data on aerosol size distributions, cloud condensation nuclei (CCN), and ice nucleation particles (INP). This network enables the investigation of small-scale variations in complex terrain. Two datasets are provided - one containing raw data and the other containing post-corrected data. The raw dataset provides the raw data recorded from the POPS which were deployed at each of the six sites. These data are organized by site and broken down into daily data files. The six site names used here are: “gothic”, “irwin”, “cbtop”, “cbmid”, “pumphouse”, and “snodgrass”. These data are not cleaned or post-corrected, but some flags have been added. The data are reported at 1 second time resolution. The post-corrected dataset provides the post-corrected and cleaned data recorded from the POPS which were deployed at each of the six sites. This data are also organized by site (same as those found in the raw data) and broken down into daily data files. Unlike the raw POPS data, these data have already been cleaned to remove what we believe are bad values. These data should be ready to use with no cleaning. For a full description of the cleaning and post-correction process, see the readme.

54 ENVIRONMENTAL SCIENCES↗

LANDSAT-D accelerated payload correction subsystem output computer compatible tape format

The NASA GSFC LANDSAT-D Ground Segment (GS) is developing an Accelerated Payload Correction Subsystem (APCS) to provide Thematic Mapper (TM) image correction data to be used outside the GS. This correction data is computed from a subset of the TM Payload Correction Data (PCD), which is downlinked from the spacecraft in a 32 Kbps data stream, and mirror scan correction data (MSCD), which is extracted from the wideband video data. This correction data is generated in the GS Thematic Mapper Mission Management Facility (MMF-T), and is recorded on a 9-track 1600 bit per inch computer compatible tape (CCT). This CCT is known as a APCS Output CCT (AOT). The AOT follows standardized corrections with respect to data formats, record construction and record identification. Applicable documents are delineated; common conventions which are used in further defining the structure, format and content of the AOT are defined; and the structure and content of the AOT are described.

Source record↗

Methodology for matching experimental and computational aerodynamic data

Correction factor methodologies have been developed which use steady experimental or analytical pressure or force data to correct steady and unsteady aerodynamic calculations. Three methods of calculating correction factors have been developed to match steady surface pressure distributions, to match airfoil section forces and moments. Data for a rectangular supercritical wing that was previously tested in the NASA Langley Research Center Transonic Dynamics Tunnel have been used to determine correction factors to match surface pressure distributions for a range of Mach numbers.

Wieseman, Carol D.↗

Methodology for matching experimental and analytical aerodynamic data

Correction factor methodologies have been developed which use steady experimental or analytical pressure or force data to correct steady and unsteady aerodynamic calculations. Three methods of calculating correction factors have been developed to match steady surface pressure distributions, to match airfoil section forces and moments, and to match total forces and moments. Data for a rectangular supercritical wing that was previously tested in the NASA Langley Research Center Transonic Dynamics Tunnel have been used to determine correction factors to match surface pressure distributions for a range of Mach numbers.

Wieseman, Carol D.↗