Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “copper oxide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Life test results for an ensemble of CO2 lasers

The effects of cathode material, cathode operating temperature, anode configuration, window materials, and hydrogen additives on laser lifetime are determined. Internally oxidized copper and silber-copper alloy cathodes were tested. The cathode operating temperature was raised in some tubes through the use of thermal insulation. Lasers incorporating thermally insulated silver copper oxide cathodes clearly yielded the longest lifetimes-typically in excess of 22,000 hours. The use of platinum sheet versus platinum pin anodes had no observable effect on laser lifetime. Similarly, the choice of germanium, cadmium telluride, or zinc selenide as the optical window material appears to have no impact on lifetime.

Peruso, C. J.↗
NASA NTRS1990

Magnetism and superconductivity of some Tl-Cu oxides

Many copper oxide based Thallium compounds have now been discovered. In comparison to the Bi-compounds, the Tl-system shows a richer diversity; viz., High Temperature Superconductors (HTSC) can be obtained with either one or two Tl-0 layers (m = 1,2); also, the triple-digit phases are easier to synthesize. The value of d, oxygen stoichiometry, is critical to achieving superconductivity. The Tl system is robust to oxygen loss; Tl may be lost or incorporated by diffusion. A diffusion coefficient equal to 10 ms at 900 C was determined. Both ortho-rhombic and tetragonal structures are evidenced, but HTSC behavior is indifferent to the crystal symmetry. This system has the highest T(sub c) confirmed. T(sub c) generally increases with p, the number of CuO layers, but tends to saturate at p = 3. Zero resistance as high as 125K has been observed. Most of these HTSC's are hole type, but the Ce-doped specimens may be electronic. The magnetic aspects were studied; because in addition to defining the perfectly diamagnetic ground state as in the conventional superconductors, magnetism of the copper oxides show a surprising variety. This is true of both the normal and the superconducting states. Also, due to the large phonon contribution to the specific heat at the high T(sub c) accurate thermal measurement of important parameters such as the sp. heat jump, electronic density of states, D(Ef) and coherence length are uncertain, and thus, are estimated from the magnetic results. Results from the Tl-system CuO, LaBaCuO, 120 and the Bi-CuO compounds are discussed. The emphasis is on the role of magnetism in the TlCuO HTSC, but technological aspects are also pointed out.

Datta, Timir↗
NASA NTRS1991

Magnetism and superconductivity of some Tl-Cu oxides

Many copper oxide based Thallium compounds are now known. In comparison to the Bi-compounds, the Tl-system shows a richer diversity; i.e., High Temperature Superconductors (HTSC) can be obtained with either one or two Tl-0 layers (m = 1,2); also, the triple-digit phases are easier to synthesize. The value of d, oxygen stoichiometry, is critical to achieving superconductivity. The Tl system is robust to oxygen loss; Tl may be lost or incorporated by diffusion. A diffusion coefficient equal to 10 ms at 900 C was determined. Both ortho-rhombic and tetragonal structures are found, but HTSC behavior is indifferent to the crystal symmetry. This system has the highest T(sub c) confirmed. T(sub c) generally increases with p, the number of CuO layers, but tends to saturate at p = 3. Zero resistance was observed at temperatures as great as 125 K. Most of these HTSC's are hole type, but the Ce-doped specimens may be electronic. The magnetic aspects were studied; because in addition to defining the perfectly diamagnetic ground state as in conventional superconductors, magnetism of the copper oxides show a surprising variety. This is true of both the normal and the superconducting states. Also, due to the large phonon contribution to the specific heat at the high T(sub c) jump, electronic density of states, D(Ef), and coherence length are uncertain, and thus, are estimated from the magnetic results. Results from the Tl-system CuO, LaBaCuO,120 and the Bi-CuO compounds are discussed. The emphasis is on the role of magnetism in the Tl-CuO HTSC, but technological aspects are also pointed out.

Datta, Timir↗
DOE OSTI2025

Understanding how defects and dopant atoms in copper surface oxides affect reactivity

Copper and its oxides are key catalytic materials, on which reactions often occur at the metal/oxide interface. Here, in this work, we directly connect the induction period observed during methanol-driven reduction of thin-film copper oxides to their atomic-scale structural order. Using temperature-programmed desorption (TPD) methanol titrations combined with scanning tunneling microscopy, we show that highly ordered oxide phases – particularly the “29” structure with its low defect density – exhibit long induction periods and initially low reactivity. The induction period, defined as the number of methanol TPD cycles required to reach half of the maximum formaldehyde yield, scales with oxide order and oxygen coverage. Enhanced reactivity of well-ordered oxides emerges only after repeated methanol adsorption/desorption cycles generate oxygen vacancies and new Cu(111)/Cu x O interfacial sites. In contrast, disordered or sub-stoichiometric oxides, which contain more intrinsic defects and interfaces, are active from the first TPD cycle. We further examine how dilute Pt and Rh dopants influence oxide order and reactivity: 1% Pt increases defect density and catalytic activity, while 1% Rh promotes oxide ordering and longer induction periods. These findings demonstrate that dilute alloying provides a potential method for tuning the structure and reactivity of Cu(111)/Cu x O interfaces.

Cu(111)Methanol oxidation↗
NASA NTRS1979

Absorptive coating for aluminum solar panels

Method for coating forming coating of copper oxide from copper component of sheet aluminum/copper alloy provides strong durable solar heat collector panels. Copper oxide coating has solar absorption characteristics similar to black chrome and is much simpler and less costly to produce.

Desmet, D.↗
NASA NTRS2001

Investigation into Spectroscopic Techniques for Thermal Barrier Coating Spall Detection

Spectroscopic methods are proposed for detection of thermal barrier coating (TBC) spallation from engine hot zone components. These methods include absorption and emission of airborne marker species originally embedded in the TBC bond coat. In this study, candidate marker materials for this application were evaluated. Thermochemical analysis of candidate marker materials combined with additional constraints such as toxicity and uniqueness to engine environment, provided a short list of four potential species: platinum, copper oxide, zinc oxide. and indium. The melting point of indium was considered to be too low for serious consideration. The other three candidate marker materials, platinum, copper oxide, and zinc oxide were placed in a high temperature furnace and emission and absorption properties were measured over a temperature range from 800-1400 C and a spectral range from 250 to 18000 nm. Platinum did not provide the desired response, likely due to the low vapor Pressure of the metallic species and the low absorption of the oxide species. It was also found, however. that platinum caused a broadening of the carbon dioxide absorption at 4300 nm. The nature of this effect is not known. Absorption and emission caused by sodium and potassium impurities in the platinum were found in the platinum tests. Zinc oxide did not provide the desired response, again, most likely due to the low vapor pressure of the metallic species and the low absorption of the oxide species. Copper oxide generated two strongly temperature dependent absorption peaks at 324.8 and 327.4 nm. The melting point of copper oxide was determined to be too low for serious consideration as marker material.

deGroot, Wim↗
NASA NTRS2002

Oxidation Behavior of GRCop-84 Copper Alloy Assessed

NASA's goal of safe, affordable space transportation calls for increased reliability and lifetimes of launch vehicles, and significant reductions of launch costs. The areas targeted for enhanced performance in the next generation of reusable launch vehicles include combustion chambers and nozzle ramps; therefore, the search is on for suitable liner materials for these components. GRCop-84 (Cu-8Cr-4Nb), an advanced copper alloy developed at the NASA Glenn Research Center in conjunction with Case Western Reserve University, is a candidate. The current liner of the Space Shuttle Main Engine is another copper alloy, NARloy-Z (Cu-3Ag-0.1Zr). It provides a benchmark against which to compare the properties of candidate successors. The thermomechanical properties of GRCop-84 have been shown to be superior, and its physical properties comparable, to those of NARloy-Z. However, environmental durability issues control longevity in this application: because copper oxide scales are not highly protective, most copper alloys are quickly consumed in oxygen environments at elevated temperatures. In consequence, NARloy-Z and most other copper alloys are prone to blanching, a degradation process that occurs through cycles of oxidation-reduction as the oxide is repeatedly formed and removed because of microscale fluctuations in the oxygen-hydrogen fuel systems of rocket engines. The Space Shuttle Main Engine lining typically degraded by blanching-induced hot spots that lead to surface roughening, pore formation, and coolant leakage. Therefore, resistance to oxidation and blanching are key requirements for second-generation reusable launch vehicle liners. The rocket engine ambient includes H2 (fuel) and H2O (combustion product) and is, hence, under reduced oxygen partial pressures. Accordingly, our studies were expanded to include oxygen partial pressures as low as 322 parts per million (ppm) at the temperatures likely to be experienced in service. A comparison of 10-hr weight gains of GRCop-84, NARloy-Z, and pure copper in 0.032, 2.2, and 100 percent oxygen from 550 to 750 C is shown. In 2.2 vol% and higher oxygen content, GRCop-84 oxidation was slower than that of NARloy-Z or Cu, but that advantage was lost or diminished in 322-ppm O2. Over longer (50-hr) exposures in 1.0 atm O2, however, the advantage of GRCop-84 increased significantly, its oxidation rate becoming approximately 10 times slower than those of Cu and NARloy-Z from 500 to 700 C. Weight gains were moderate and the kinetics parabolic for all three materials in 2.2 vol% and higher oxygen content; however, in 322-ppm O2, the scales were nonprotective below about 650 C, as reflected in linear kinetics and large weight gains. The superior oxidation resistance of GRCop-84 is likely related to the kinetics of extra oxygen consumption to form the additional oxides of Cr and Nb detected beneath the GRCop-84 oxide layer. While we continue to evaluate the blanching resistance of GRCop-84 in other tests, these oxidation results indicate that GRCop-84 is suitable as a reusable launch vehicle liner, and in applications where it is desired to use a copper alloy but without the risk of oxidative failure. Three bar charts comparing overall specific weight gains by each of the three materials studied. The top chart is for oxidation in 1.0 atm of oxygen, the middle is for 2.2% oxygen (balance argon), and the bottom is for 0.0322% oxygen. GRCop-84 outperforms the other two materials, showing the least weight gain in nearly all cases.

Thomas-Ogbuji, Linus U.↗
NASA NTRS2019

Applications of Atomic Layer Deposition in the Modification of Carbon Nanotubes

Atomic Layer Deposition (ALD) is a cost-effective nanoadditive-manufacturing technique that allows for conformal coating of substrates with atomic control in a benign temperature and pressure environment. Using paired precursor gases, thin films can be deposited on flat or textured surfaces ranging from glass, polymers, aerogels, and metals. Through atomic layer control, where single layers of atoms are deposited, fabrication of metal transparent films, nano-laminates, and coatings of nano-channels and pores is achievable. Reaction mechanisms in ALD are normally self-limiting, allowing for atomically accurate control of nanometer (nm) thicknesses. Therefore, high uniformity and precise thickness control make ALD an attractive process for the creation of novel nano-scale devices. Decreases in resistivity and density of electrical wire are needed to improve the function of electronics, electric motors and cables. Such improvements may be accomplished by adding ballistically conducting, metallic carbon nanotubes (CNT) to Cu. ALD was used to coat multiple substrates including CNT with Cu in an effort to make CNT-Cu composites which is more conductive and less dense than Cu. In addition, ALD can be used to as a method to deposit the catalyst layer seed layer for CNT growth using Ni. The ALD of copper metallic films can follow multiple reaction pathways depending on the ALD precursors used. For this work the reaction pathway was deposition of copper oxide and then post process annealing in a hydrogen environment. Copper(II) diacetylacetonate (Cu(acac)2) and ozone are used as precursors for copper oxide. As-deposited copper oxide films prepared at 180°C resulted in a growth per cycle of 1.0 A/cycle with low film resistivity.

Dwivedi, Vivek H.↗
DOE OSTI2025

CeO 2 Promoted CuO/MgO-Al 2 O 3 Catalyst with Enhanced Activity and Water-Resistance for CO Oxidation

Copper (Cu)-based catalysts have emerged as cost-effective and sustainable alternatives to noble metal systems (e.g., Pt, Pd) for catalytic CO oxidation. However, their practical application is hindered by insufficient low-temperature activity and rapid deactivation under wet conditions containing moisture. To address these challenges, this work introduces CeO 2 -modified CuO/MgO-Al 2 O 3 (Cu-Ce/MA) catalysts, strategically designed to enhance the catalytic performance and water resistance simultaneously. These catalytic materials were evaluated for CO oxidation under both dry and humid conditions, revealing that CeO 2 modification significantly improves the low-temperature activity. Specifically, the optimal catalyst, Cu-30Ce/MA, achieved a 50% CO conversion temperature (T 50 ) of 151 °C, a marked reduction from 218 °C on Cu/MA reference catalyst. Furthermore, the water resistance improves in a CeO 2 content-dependent manner, with higher CeO 2 loadings imparting greater stability in humid environments. Detailed characterizations demonstrate that CeO 2 promotes the dispersion of CuO and stabilizes Cu sites, while also enhancing the low-temperature reducibility and CO adsorption capacity. Crucially, CeO 2 modification suppresses the competitive H 2 O adsorption, mitigating water-induced deactivation. These synergistic effects collectively rationalize the superior activity and durability of Cu-Ce/MA catalysts. By elucidating the dual role of CeO 2 in optimizing Cu-based systems, this study advances the rational design of cost-effective catalysts for real-world CO emission control, particularly under water-rich industrial conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Incorporation of Oxygen Carrier Recycle into Large-Scale Production of Cu-Based Oxygen Carriers

One of the greatest challenges in the chemical looping combustion (CLC) of solid fuels is developing an oxygen carrier material that is reactive and attrition resistant and can be prepared at a reasonable cost. Recent efforts in oxygen carrier development have followed two primary approaches: (1) using natural ores, such as ilmenite, or (2) developing highly attrition-resistant and reactive synthetic materials. Both approaches have shortcomings, namely, the low reactivity and incompatibility of ores with solid fuel CLC and the high cost and low durability of synthetic materials. Here, a different approach is taken where attrition is assumed inevitable and the recycling of spent oxygen carrier materials is incorporated into oxygen carrier manufacture. For solid fuel CLC, Cu-based oxygen carriers are attrited and are collected with fly ash. Copper oxides are more reactive with nitric acid than most ash materials, meaning that a copper-nitrate-rich leachate can be generated. This copper nitrate stream could then be reused in oxygen carrier synthesis by impregnation. For proof of concept, leaching experiments were conducted to verify that copper oxides are selectively leached from ash-containing spent oxygen carriers. Several cases for process design are proposed based on the composition of spent materials, as the degree of copper oxidation and type of solid fuel dictate leaching residence times and general processing intensity. The four stages proposed here include impurity removal, copper leaching and recovery, solid–liquid separation, and evaporation/concentrating. The resulting process should be able to recover up to 95% of copper while minimizing inclusion of undesirable ash-based impurities.

anions↗
DOE OSTI2025

Tuning the Selectivity of Carboxylic Acid–Based Eutectic Solvents for the Dissolution and Electrochemical Separation of Metal Oxides

Extracting metals from natural resources and recovering from waste materials with less-hazardous solvents is essential for sustainable technological advancements. The commonly employed method utilizes harsh chemicals for metal dissolution and the ensuing separation. Here, in this study, we examined the potential of eutectic solvents (types III and IV) as alternative media for the selective dissolution of metals and metal oxides and their subsequent electrochemical separation. Notably, type III eutectics composed of betaine:acetic acid and triazole:lactic acid exhibited excellent solubility for cobalt oxide (24.1 g·L –1 ) and copper oxide (30.5 g·L –1 ), respectively. In comparison, the type IV eutectic mixture of Ca(NO 3 ) 2 ·4H 2 O:acetic acid demonstrated the highest conductivity and lowest viscosity with solubility for both copper oxide (6.1 g·L –1 ) and metallic copper (5.4 g·L –1 from a used electronic circuit). Using a Ca(NO 3 ) 2 ·4H 2 O:acetic acid mixture, copper was selectively dissolved from a waste printed circuit board and subsequently electrodeposited onto a nickel electrode. These findings highlight the tunability of DESs for the selective recovery of metals from electronic waste, offering a promising approach for sustainable metal recycling and resource recovery.

electrodeposition↗