Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “convolutional interleaver”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

High-Performance, Low-Complexity Codes Researched for Communication Channels

NASA Lewis Research Center s Communications Technology Division has an ongoing program in the development of efficient channel coding schemes for satellite communications applications. Through a university grant, as a part of this research, the University of Toledo is investigating the performance of turbocodes, which use parallel concatenation of non-systematic convolutional encoders with an interleaver. The error correcting capacity of these codes is close to the Shannon limit. The research emphasis is on the development of low-complexity, but higher rate (greater than one half), turbocodes and on the iterative decoding of block codes.

Kwatra, Subhash C.↗
NASA NTRS2000

Full Duplex, Spread Spectrum Radio System

The goal of this project was to support the development of a full duplex, spread spectrum voice communications system. The assembly and testing of a prototype system consisting of a Harris PRISM spread spectrum radio, a TMS320C54x signal processing development board and a Zilog Z80180 microprocessor was underway at the start of this project. The efforts under this project were the development of multiple access schemes, analysis of full duplex voice feedback delays, and the development and analysis of forward error correction (FEC) algorithms. The multiple access analysis involved the selection between code division multiple access (CDMA), frequency division multiple access (FDMA) and time division multiple access (TDMA). Full duplex voice feedback analysis involved the analysis of packet size and delays associated with full loop voice feedback for confirmation of radio system performance. FEC analysis included studies of the performance under the expected burst error scenario with the relatively short packet lengths, and analysis of implementation in the TMS320C54x digital signal processor. When the capabilities and the limitations of the components used were considered, the multiple access scheme chosen was a combination TDMA/FDMA scheme that will provide up to eight users on each of three separate frequencies. Packets to and from each user will consist of 16 samples at a rate of 8,000 samples per second for a total of 2 ms of voice information. The resulting voice feedback delay will therefore be 4 - 6 ms. The most practical FEC algorithm for implementation was a convolutional code with a Viterbi decoder. Interleaving of the bits of each packet will be required to offset the effects of burst errors.

Harvey, Bruce A.↗
NASA NTRS1993

A simulation study of the performance of the NASA (2,1,6) convolutional code on RFI/burst channels

In an earlier report, the LINKABIT Corporation studied the performance of the (2,1,6) convolutional code on the radio frequency interference (RFI)/burst channel using analytical methods. Using an R(sub 0) analysis, the report concluded that channel interleaving was essential to achieving reliable performance. In this report, Monte Carlo simulation techniques are used to study the performance of the convolutional code on the RFI/burst channel in more depth. The basic system model under consideration is shown. The convolutional code is the NASA standard code with generators g(exp 1) = 1+D(exp 2)+D(exp 3)+D(exp 5)+D(exp 6) and g(exp 2) = 1+D+D(exp 2)+D(exp 3)+D(exp 6) and d(sub free) = 10. The channel interleaver is of the convolutional or periodic type. The binary output of the channel interleaver is transmitted across the channel using binary phase shift keying (BPSK) modulation. The transmitted symbols are corrupted by an RFI/burst channel consisting of a combination of additive white Gaussian noise (AWGN) and RFI pulses. At the receiver, a soft-decision Viterbi decoder with no quantization and variable truncation length is used to decode the deinterleaved sequence.

Perez, Lance C.↗
NASA NTRS1981

An experimental study of the concatenated Reed-Solomon/Viterbi channel coding system performance and its impact on space communications

The need for efficient space communication at very low bit error probabilities to the specification and implementation of a concatenated coding system using an interleaved Reed-Solomon code as the outer code and a Viterbi-decoded convolutional code as the inner code. Experimental results of this channel coding system are presented under an emulated S-band uplink and X-band downlink two-way space communication channel, where both uplink and downlink have strong carrier power. This work was performed under the NASA End-to-End Data Systems program at JPL. Test results verify that at a bit error probability of 10 to the -6 power or less, this concatenated coding system does provide a coding gain of 2.5 dB or more over the Viterbi-decoded convolutional-only coding system. These tests also show that a desirable interleaving depth for the Reed-Solomon outer code is 8 or more. The impact of this "virtually" error-free space communication link on the transmission of images is discussed and examples of simulation results are given.

Liu, K. Y.↗
NASA NTRS1999

Punctured Parallel and Serial Concatenated Convolutional Codes for BPSK/QPSK Channels

As available bandwidth for communication applications becomes scarce, bandwidth-efficient modulation and coding schemes become ever important. Since their discovery in 1993, turbo codes (parallel concatenated convolutional codes) have been the center of the attention in the coding community because of their bit error rate performance near the Shannon limit. Serial concatenated convolutional codes have also been shown to be as powerful as turbo codes. In this dissertation, we introduce algorithms for designing bandwidth-efficient rate r = k/(k + 1),k = 2, 3,..., 16, parallel and rate 3/4, 7/8, and 15/16 serial concatenated convolutional codes via puncturing for BPSK/QPSK (Binary Phase Shift Keying/Quadrature Phase Shift Keying) channels. Both parallel and serial concatenated convolutional codes have initially, steep bit error rate versus signal-to-noise ratio slope (called the -"cliff region"). However, this steep slope changes to a moderate slope with increasing signal-to-noise ratio, where the slope is characterized by the weight spectrum of the code. The region after the cliff region is called the "error rate floor" which dominates the behavior of these codes in moderate to high signal-to-noise ratios. Our goal is to design high rate parallel and serial concatenated convolutional codes while minimizing the error rate floor effect. The design algorithm includes an interleaver enhancement procedure and finds the polynomial sets (only for parallel concatenated convolutional codes) and the puncturing schemes that achieve the lowest bit error rate performance around the floor for the code rates of interest.

Acikel, Omer Fatih↗
NASA NTRS1995

On the design of turbo codes

In this article, we design new turbo codes that can achieve near-Shannon-limit performance. The design criterion for random interleavers is based on maximizing the effective free distance of the turbo code, i.e., the minimum output weight of codewords due to weight-2 input sequences. An upper bound on the effective free distance of a turbo code is derived. This upper bound can be achieved if the feedback connection of convolutional codes uses primitive polynomials. We review multiple turbo codes (parallel concatenation of q convolutional codes), which increase the so-called 'interleaving gain' as q and the interleaver size increase, and a suitable decoder structure derived from an approximation to the maximum a posteriori probability decision rule. We develop new rate 1/3, 2/3, 3/4, and 4/5 constituent codes to be used in the turbo encoder structure. These codes, for from 2 to 32 states, are designed by using primitive polynomials. The resulting turbo codes have rates b/n (b = 1, 2, 3, 4 and n = 2, 3, 4, 5, 6), and include random interleavers for better asymptotic performance. These codes are suitable for deep-space communications with low throughput and for near-Earth communications where high throughput is desirable. The performance of these codes is within 1 dB of the Shannon limit at a bit-error rate of 10(exp -6) for throughputs from 1/15 up to 4 bits/s/Hz.

Divsalar, D.↗
NASA NTRS1977

Advanced imaging communication system

Key elements of system are imaging and nonimaging sensors, data compressor/decompressor, interleaved Reed-Solomon block coder, convolutional-encoded/Viterbi-decoded telemetry channel, and Reed-Solomon decoding. Data compression provides efficient representation of sensor data, and channel coding improves reliability of data transmission.

Hilbert, E. E.↗
NASA NTRS1989

Orbital maneuvering vehicle teleoperation and video data compression

The Orbital Maneuvering Vehicle (OMV) and concepts of teleoperation and video data compression as applied to OMV design and operation are described. The OMV provides spacecraft delivery, retrieval, reboost, deboost and viewing services, with ground-control or Space Station operation, through autonomous navigation and pilot controlled maneuvers. Communications systems are comprised of S-band RF command, telemetry, and compressed video data links through the TDRSS and GSTDN networks. The control console video monitors display a monochrome image at an update rate of five frames per second. Depending upon the mode of operation selected by the pilot, the video resolution is either 255 x 244 pixels, or 510 x 244 pixels. Since practically all video image redundancy is removed by the compression process, the video reconstruction is particularly sensitive to data transmission bit errors. Concatenated Reed-Solomon and convolution coding are used with helical data interleaving for error detection and correction, and an error-containment process minimizes the propagation of error effects throughout the video image. Video sub-frame replacement is used, in the case of a non-correctable error or error burst, to minimize the visual impact to the pilot.

Jones, Steve↗
NASA NTRS1993

Enhanced decoding for the Galileo S-band mission

A coding system under consideration for the Galileo S-band low-gain antenna mission is a concatenated system using a variable redundancy Reed-Solomon outer code and a (14,1/4) convolutional inner code. The 8-bit Reed-Solomon symbols are interleaved to depth 8, and the eight 255-symbol codewords in each interleaved block have redundancies 64, 20, 20, 20, 64, 20, 20, and 20, respectively (or equivalently, the codewords have 191, 235, 235, 235, 191, 235, 235, and 235 8-bit information symbols, respectively). This concatenated code is to be decoded by an enhanced decoder that utilizes a maximum likelihood (Viterbi) convolutional decoder; a Reed Solomon decoder capable of processing erasures; an algorithm for declaring erasures in undecoded codewords based on known erroneous symbols in neighboring decodable words; a second Viterbi decoding operation (redecoding) constrained to follow only paths consistent with the known symbols from previously decodable Reed-Solomon codewords; and a second Reed-Solomon decoding operation using the output from the Viterbi redecoder and additional erasure declarations to the extent possible. It is estimated that this code and decoder can achieve a decoded bit error rate of 1 x 10(exp 7) at a concatenated code signal-to-noise ratio of 0.76 dB. By comparison, a threshold of 1.17 dB is required for a baseline coding system consisting of the same (14,1/4) convolutional code, a (255,223) Reed-Solomon code with constant redundancy 32 also interleaved to depth 8, a one-pass Viterbi decoder, and a Reed Solomon decoder incapable of declaring or utilizing erasures. The relative gain of the enhanced system is thus 0.41 dB. It is predicted from analysis based on an assumption of infinite interleaving that the coding gain could be further improved by approximately 0.2 dB if four stages of Viterbi decoding and four levels of Reed-Solomon redundancy are permitted. Confirmation of this effect and specification of the optimum four-level redundancy profile for depth-8 interleaving is currently being done.

Dolinar, S.↗
NASA NTRS2004

Serial-Turbo-Trellis-Coded Modulation with Rate-1 Inner Code

Serially concatenated turbo codes have been proposed to satisfy requirements for low bit- and word-error rates and for low (in comparison with related previous codes) complexity of coding and decoding algorithms and thus low complexity of coding and decoding circuitry. These codes are applicable to such high-level modulations as octonary phase-shift keying (8PSK) and 16-state quadrature amplitude modulation (16QAM); the signal product obtained by applying one of these codes to one of these modulations is denoted, generally, as serially concatenated trellis-coded modulation (SCTCM). These codes could be particularly beneficial for communication systems that must be designed and operated subject to limitations on bandwidth and power. Some background information is prerequisite to a meaningful summary of this development. Trellis-coded modulation (TCM) is now a well-established technique in digital communications. A turbo code combines binary component codes (which typically include trellis codes) with interleaving. A turbo code of the type that has been studied prior to this development is composed of parallel concatenated convolutional codes (PCCCs) implemented by two or more constituent systematic encoders joined through one or more interleavers. The input information bits feed the first encoder and, after having been scrambled by the interleaver, enter the second encoder. A code word of a parallel concatenated code consists of the input bits to the first encoder followed by the parity check bits of both encoders. The suboptimal iterative decoding structure for such a code is modular, and consists of a set of concatenated decoding modules one for each constituent code connected through an interleaver identical to the one in the encoder side. Each decoder performs weighted soft decoding of the input sequence. PCCCs yield very large coding gains at the cost of a reduction in the data rate and/or an increase in bandwidth.

Divsalar, Dariush↗
NASA NTRS1990

VLSI single-chip (255,223) Reed-Solomon encoder with interleaver

The invention relates to a concatenated Reed-Solomon/convolutional encoding system consisting of a Reed-Solomon outer code and a convolutional inner code for downlink telemetry in space missions, and more particularly to a Reed-Solomon encoder with programmable interleaving of the information symbols and code correction symbols to combat error bursts in the Viterbi decoder.

Hsu, In-Shek↗
NASA NTRS1995

Joint Synchronization Of Viterbi And Reed-Solomon Decoders

Synchronization times reduced to reduce loss of data. Scheme for decoding received doubly encoded binary-data signal provides for joint synchronization of two decoders. Applies to concatenated error-correcting channel coding communication system in which, at transmitter, data first encoded by interleaved Reed-Solomon code (block code), then by convolutional code.

Statman, Joseph I.↗
NASA NTRS2009

LDPC-PPM Coding Scheme for Optical Communication

In a proposed coding-and-modulation/demodulation-and-decoding scheme for a free-space optical communication system, an error-correcting code of the low-density parity-check (LDPC) type would be concatenated with a modulation code that consists of a mapping of bits to pulse-position-modulation (PPM) symbols. Hence, the scheme is denoted LDPC-PPM. This scheme could be considered a competitor of a related prior scheme in which an outer convolutional error-correcting code is concatenated with an interleaving operation, a bit-accumulation operation, and a PPM inner code. Both the prior and present schemes can be characterized as serially concatenated pulse-position modulation (SCPPM) coding schemes. Figure 1 represents a free-space optical communication system based on either the present LDPC-PPM scheme or the prior SCPPM scheme. At the transmitting terminal, the original data (u) are processed by an encoder into blocks of bits (a), and the encoded data are mapped to PPM of an optical signal (c). For the purpose of design and analysis, the optical channel in which the PPM signal propagates is modeled as a Poisson point process. At the receiving terminal, the arriving optical signal (y) is demodulated to obtain an estimate (a^) of the coded data, which is then processed by a decoder to obtain an estimate (u^) of the original data.

Barsoum, Maged↗
NASA NTRS1994

Error coding simulations in C

When data is transmitted through a noisy channel, errors are produced within the data rendering it indecipherable. Through the use of error control coding techniques, the bit error rate can be reduced to any desired level without sacrificing the transmission data rate. The Astrionics Laboratory at Marshall Space Flight Center has decided to use a modular, end-to-end telemetry data simulator to simulate the transmission of data from flight to ground and various methods of error control. The simulator includes modules for random data generation, data compression, Consultative Committee for Space Data Systems (CCSDS) transfer frame formation, error correction/detection, error generation and error statistics. The simulator utilizes a concatenated coding scheme which includes CCSDS standard (255,223) Reed-Solomon (RS) code over GF(2(exp 8)) with interleave depth of 5 as the outermost code, (7, 1/2) convolutional code as an inner code and CCSDS recommended (n, n-16) cyclic redundancy check (CRC) code as the innermost code, where n is the number of information bits plus 16 parity bits. The received signal-to-noise for a desired bit error rate is greatly reduced through the use of forward error correction techniques. Even greater coding gain is provided through the use of a concatenated coding scheme. Interleaving/deinterleaving is necessary to randomize burst errors which may appear at the input of the RS decoder. The burst correction capability length is increased in proportion to the interleave depth. The modular nature of the simulator allows for inclusion or exclusion of modules as needed. This paper describes the development and operation of the simulator, the verification of a C-language Reed-Solomon code, and the possibility of using Comdisco SPW(tm) as a tool for determining optimal error control schemes.

Noble, Viveca K.↗
NASA NTRS1998

Investigation of Different Constituent Encoders in a Turbo-code Scheme for Reduced Decoder Complexity

A large number of papers have been published attempting to give some analytical basis for the performance of Turbo-codes. It has been shown that performance improves with increased interleaver length. Also procedures have been given to pick the best constituent recursive systematic convolutional codes (RSCC's). However testing by computer simulation is still required to verify these results. This thesis begins by describing the encoding and decoding schemes used. Next simulation results on several memory 4 RSCC's are shown. It is found that the best BER performance at low E(sub b)/N(sub o) is not given by the RSCC's that were found using the analytic techniques given so far. Next the results are given from simulations using a smaller memory RSCC for one of the constituent encoders. Significant reduction in decoding complexity is obtained with minimal loss in performance. Simulation results are then given for a rate 1/3 Turbo-code with the result that this code performed as well as a rate 1/2 Turbo-code as measured by the distance from their respective Shannon limits. Finally the results of simulations where an inaccurate noise variance measurement was used are given. From this it was observed that Turbo-decoding is fairly stable with regard to noise variance measurement.

Kwatra, S. C.↗
NASA NTRS1998

Design of Serially Concatenated Trellis Coded Modulation

Serial concatenation of an outer binary convolutional code with an inner TCM code over a multidimensional Euclidean constellation through an interleaver, allows to extend the extremely good performance of turbo codes to the case of high spectral efficiency.

Serial Concatenated trellis code↗
NASA NTRS1990

The Space Telescope SI C&DH system

The Hubble Space Telescope Scientific Instrument Control and Data Handling Subsystem (SI C&DH) is designed to interface with five scientific instruments of the Space Telescope to provide ground and autonomous control and collect health and status information using the Standard Telemetry and Command Components (STACC) multiplex data bus. It also formats high throughput science data into packets. The packetized data is interleaved and Reed-Solomon encoded for error correction and Pseudo Random encoded. An inner convolutional coding with the outer Reed-Solomon coding provides excellent error correction capability. The subsystem is designed with the capacity for orbital replacement in order to meet a mission life of fifteen years. The spacecraft computer and the SI C&DH computer coordinate the activities of the spacecraft and the scientific instruments to achieve the mission objectives.

Gadwal, Govind R.↗