SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Simple and economical conversion of aqueous ethanol feed streams into butenes by a single step method using transition metal oxides on a silica supports under preselected processing conditions. By directly producing a C4-rich olefin mixture from an ethanol containing stream various advantages are presented including, but not limited to, significant cost reduction in capital expenses and operational expenses.
The Ohio State University (OSU) is investigating the Biomass to Syngas (BTS) chemical looping technology to produce syngas for chemical production applications from biomass under US Department of Energy (DOE) Award #DE-EE0007530. The BTS process aligns with the programmatic area of interest of “Conversion, via biological, thermal, catalytic or chemical means, of acceptable feedstocks into advanced biofuels and/or biobased products including intermediate and end-use products”. Compared to conventional biomass gasification processes, the BTS process eliminates the need for air separation units and tar reforming reactors, which leads to energy efficiency improvement and capital cost reduction. The overall objective is to ascertain the potential of biomass gasification based on the chemical looping technique through mitigation of the possible techno-economic challenges in the steps of scale up for commercialization. The scope of work consists of 1) designing, constructing and operating a 10 kWth commercially scalable sub-pilot BTS system and; 2) completing a comprehensive techno-economic analysis (TEA) of the BTS process using methanol production as an example. Over the course of the project, the project team completed the design, fabrication, and operation of a 10 kWth sub-pilot scale test unit for the BTS process. Corn cob and wood pellets were successfully tested in the unit for high purity syngas generation in extended test campaigns that totals over 200 hours. Syngas purity (H2 and CO) of >70% was achieved with a CH 4 concentration of <6%. The H 2 /CO ratio was greater than 1.8. A comprehensive techno-economic analysis was performed to compare the BTS process and a reference indirectly heated gasification process for methanol synthesis. The result, updated with experimental results for BTS process performance, shows a methanol required selling price (MSP) of $\$ $1.15/gal, compared to $1.28/gal for the reference case.
Recent work at the National Renewable Energy Laboratory (NREL) and throughout the bioenergy community has highlighted incentives associated with co-processing bio-intermediates in existing refineries to reduce capital costs associated with renewable fuels and chemicals production and reduce overall risk for emerging biomass conversion technologies. This presentation summarizes the techno-economic analysis results from the NREL-Petrobras collaboration that focused on refinery integration of fast pyrolysis oil through co-processing in the fluid catalytic cracking (FCC) process. The NREL-Petrobras work highlights the economic opportunity for refiners to engage in co-processing for low-carbon products and introduces the risks for refiners based on variability in crude and fossil-product markets. The NREL-Petrobras results also serve as a basis to inform policy design that reduces economic risk for refinery co-processing and repurposing opportunities. The final topics in the presentation highlight experimental capabilities and emerging analysis approaches at NREL and partner laboratories that support the development and commercial deployment of refinery utilization strategies.
Catalytic Fast Pyrolysis (CFP) of biomass provides an opportunity for producing stabilized bio-oils (CFP oils) that can be further processed into hydrocarbon transportation fuels via hydroprocessing. Standalone hydrotreating of CFP oils has been pursued and has been shown to be able to produce hydrocarbon products with low oxygen contents of <1wt%, but the process is costly due to the high requirements of hydrogen and high capital costs. The costs can be reduced by co-processing in refineries, which takes advantage of the existing refinery infrastructure and the economies of the larger scale of petroleum processing operations. In this contribution, we evaluated co-hydrotreating of CFP oil with straight-run diesel in a laboratory continuous hydrotreating reactor. The CFP oil had been produced over a bi-functional metal-acid catalyst (Pt/TiO2) and contained 17 wt% oxygen on dry basis, and it was fed to the reactor together with straight-run diesel in the proportion of 20 vol%:80 vol%. The co-hydrotreated diesel products had acceptable cetane numbers (>40), and the calculated carbon efficiencies were high (~95%) for the CFP portion of the feed mixtures. Biogenic carbon incorporation in the product was confirmed by C-14 analysis. Sulfided NiMo catalyst gave better performance with respect to the diesel product quality than CoMo did due to the higher hydrogenation activity of NiMo. A comparison of standalone hydrotreating of the CFP oil and the straight-run diesel to co-hydrotreating showed good correspondence. Major challenges and risks associated with co-hydrotreating are discussed in this presentation.
Several studies have identified rare earths as critical materials. Although reasonably abundant in the Earth’s crust, rare earths typically occur in low concentrations of mined ores. Processes for recovering rare earth concentrates from these ores are complex and capital intensive. Further, lead times for deposit development, licensing, and construction are long, with reports of 10- 15 years. China is a major player in the rare earths supply chain, both in production capacity and technology innovation. In 2017, China supplied more than 80% of global rare earth oxide demand. Rare earth elements (REEs) have unique magnetic, catalytic, and phosphorescent properties that significantly improve performance of a wide range of technologies. These technologies span aerospace, energy, telecommunications, electronics, transportation, defense, and other diverse applications. Consequently, disruptions in rare earth supply can have a significant societal impact. Estimating that impact requires understanding of the dynamics across the supply chain, from rare earth oxide extraction to end use application. This report documents Argonne’s Global Critical Materials model (GCMat), first described by Riddle et al. 2015. GCMat provides capabilities to explore supply chain dynamics and uncertainty under scenarios of demand growth or shrinkage, technology adoption, supply disruptions, and trade policies and mitigation strategies of new supply sources, product substitution, consumer thrifting, and stockpiling. Supply chain participants from rare earth mining through final demand are modeled as interacting agents who make market decisions independently as time progresses. Since the version documented in Riddle et al. 2015, GCMat has been expanded to cover additional REEs, derived products and supply chains that use these REEs, and includes new agent behaviors and modeling capabilities. Section 2 provides a summary of the GCMat model design, including the structure of the model and key assumptions, section 3 summarizes methods used for model calibration and sensitivity analysis, and section 4 provides examples of model results.
Integrated Carbon Capture and Conversion of CO 2 into materials (IC3M) is an attractive solution to meet the global energy demand, reduce our dependence on fossil fuels and lower CO 2 emissions. In this work, using a water-lean post combustion capture solvent, (N-(2-ethoxyethyl)-3-morpholinopropan-1-amine) (2-EEMPA), >90% conversion of captured CO2 to hydrocarbons, mostly methane, is achieved in the presence of a heterogenous Ru catalysts under relatively mild reaction conditions (170 °C and <15 bar H 2 pressure). The catalytic performance was better in 2-EEMPA than aqueous 5M monoethanol amine (MEA). Operando NMR study showed in-situ formation of N-formamide intermediate, which underwent further hydrogenation to form methane and other higher hydrocarbons. The technoeconomic analyses (TEA) showed that the proposed integrated process can potentially improve the thermal efficiency by 5% and reduce the total capital investment and minimum synthetic natural gas (SNG) selling price by 32% and 12% respectively compared to conventional Sabatier process, highlighting the energetic and economic benefits of integrated capture and conversion. Methane derived from CO 2 and renewable H 2 source is an attractive fuel, and it has a great potential as a renewable hydrogen carrier as an environmentally responsible carbon capture and utilization approach.
A defining characteristic of nearly all catalytically functional MOFs is uniform, molecular-scale porosity. MOF pores, linkers and nodes that define them, help regulate reactant and product transport, catalyst siting, catalyst accessibility, catalyst stability, catalyst activity, co-catalyst proximity, composition of the chemical environment at and beyond the catalytic active site, chemical intermediate and transition-state conformations, thermodynamic affinity of molecular guests for MOF interior sites, framework charge and density of charge-compensating ions, pore hydrophobicity/hydrophilicity, pore and channel rigidity vs. flexibility, and other features and properties. Collectively and individually, these properties help define overall catalyst functional behaviour. Here, this review focuses on how porous, catalyst-containing MOFs capitalize on molecular-scale confinement, containment, isolation, environment modulation, energy delivery, and mobility to accomplish desired chemical transformations with potentially superior selectivity or other efficacy, especially in comparison to catalysts in homogeneous solution environments.
A key challenge facing most bioprocessing operations is that multiple unit operations are required, thereby resulting in complex, energy-intensive, and expensive processes. Further, biomass transportation costs drive the need for smaller, distributed processing plants. To incorporate the smaller scales desirable for biomass, novel processes must be developed with reduced capital costs. With over 20 years of experience in the development and commercialization of microchannel reactor technology, Oregon State University will partner with Pacific Northwest National Laboratory to demonstrate a microchannel reactor with lower capital costs for an alcohol-to-jet (ATJ) process technology that is currently being commercialized by LanzaTech. Ethanol can be produced from biomass feedstocks such as LanzaTech’s proprietary biochemical process using carbon from a number of possible feedstocks; syngas generated from biomass resources (e.g., MSW, organic industrial waste, agriculture waste) or reformed biogas, or from other biomass feedstocks such as corn kernel fiber. Ethanol then undergoes catalytic dehydration to form ethylene followed by a two-step oligomerization, hydrogenation, and fractionation to control the hydrocarbon product slate to the jet-range. Successful process development aided by a market pull for low carbon aviation fuel has spurred scale-up and commercial demonstration. However, Sustainable Aviation Fuel is a very price sensitive market and improved economics through process intensification will make the current ATJ process even more attractive. Recent efforts at PNNL have culminated in the development of a new catalyst technology for the conversion of ethanol to n-butene-rich olefins. A greater than 90% conversion, total olefin selectivity of 80-90% (n-butene selectivity ~60%), and good stability over a 100 hour test duration has been demonstrated at the bench scale. Producing butene-rich olefins directly from ethanol with high yield is new and impactful because the higher olefins can be selectively oligomerized to distillate-range hydrocarbons, thus eliminating one process step from the current ATJ process. Further, coupling the severely endothermic ethanol dehydration with exothermic C-C bond formation results in more energy efficient processing. Additional intensification and energy savings will stem from incorporating this new ethanol to n-butene catalyst technology within the ATJ process implemented using a microchannel reactor platform. Due to recent advances in microchannel manufacturing methods and associated cost reductions we believe the time is right to adapt this technology toward new commercial bioconversion applications.
Since its inception, the low-swirl burner (LSB) has shown to be a useful laboratory apparatus for fundamental studies of premixed turbulent flames. The LSB operates under wide ranges of equivalence ratios, flow rates, and turbulence intensities. Its flame is lifted and detached from the burner and allows easy access for laser diagnostics. The flame brush is axisymmetric and propagates normal to the incident reactants. Therefore, the LSB is well suited for investigating detailed flame structures and empirical coefficients such as flame speed, turbulence transport, and flame generated turbulence. Due to its capability to stabilize ultra-lean premixed turbulent flames (phi approx. = 0.55), the LSB has generated interest from the gas appliance industry for use as an economical low-NO(x) burner. Lean premixed combustion emits low levels of NO(x), due primarily to the low flame temperature. Therefore, it is a very effective NO(x) prevention method without involving selective catalytic reduction (SCR), fuel-air staging, or flue gas recirculation (FGR). En the gas turbine industry, substantial research efforts have already been undertaken and engines with lean premixed combustors are already in use. For commercial and residential applications, premixed pulsed combustors and premixed ceramic matrix burners are commercially available. These lean premixed combustion technologies, however, tend to be elaborate but have relatively limited operational flexibility, and higher capital, operating and maintenance costs. Consequently, these industries are continuing the development of lean premixed combustion technologies as well as exploring new concepts. This paper summarizes the research effects we have undertaken in the past few years to demonstrate the feasibility of applying the low-swirl flame stabilization method for a wide range of heating and power generation systems. The principle of flame stabilization by low-swirl is counter to the conventional high-swirl methods that rely on a recirculation zone to anchor the flame. In LSBS, flow recirculation is not promoted to allow the premixed turbulent flames to propagate freely. A LSB with an air-jet swirler is essentially an open tube with the swirler at its mid section. The small air-jets generate swirling motion only in the annular region and leaving the central core of the flow undisturbed, When this flow exits the burner tube, the angular momentum generates radial mean pressure gradient to diverge the non-swirling reactants stream. Consequently, the mean flow velocity decreases linearly. Propagating against this decelerating flow, the flame self-sustains at the position where the local flow velocity equals the flame speed, S(sub f). The LSB operates with a swirl number, S, between 0.02 to 0.1. This is much lower than the minimum S of 0.6 required for the high-swirl burners. We found that the swirl number needed for flame stabilization varies only slightly with fuel type, flow velocity, turbulent conditions and burner dimensions (i.e. throat diameter and swirl injection angle).
Variations of a process for removing sulfur dioxide from stack gases and using it to treat municipal waste water are described. The once-through system lowers the pH of the scrubbing water from minor depressions to a pH of about 2.5 under certain conditions. A recycle system uses iron for catalytic oxidation of sulfurous acid to sulfuric acid allowing very large amounts of sulfur dioxide to be absorbed in a small portion of water. The partial recycle system uses municipal wastewater and iron as a scrubbing medium, followed by neutralization of the wastewater with lime to produce an iron hydroxide precipitation which, when removed, produces tertiary quality treated wastewater. The SO2 scrubber is described, test results are analyzed, and a preliminary capital cost estimate for the three processes is included.
In support of the Bioenergy Technologies Office in converting lignin to fuels and chemicals, this project develops scalable separations based on membranes and Electordeionization (EDI) to recover low molecular weight (LMW) compounds from lignin rich streams. The project addresses three technology barriers in developing the bioeconomy; (1) Cost of production (2) Selective separation of organic acid species, and (3) Advanced bioprocess development. Specifically, membrane cascades using Tangential Flow Filtration (TFF) are investigated for the recovery of LMW lignin compounds from lignin rich streams such as Alkaline Pretreatment Liquor (APL), Reductive Catalytic Fractionation (RCF) oil, and Catalytic Oxidation oil. Process concepts, including dynamic filtration, are investigated to meet specific performance targets indicated by the consortium's Industrial Advisory Board for the membrane filtration including maintaining permeance > 1 LMH/bar and an overall cost target of < $1/kg of LMW lignin. EDI is investigated as an integral part of the membrane cascade to recover LMW aromatic acids and as an alternative to nanofiltration. Economic analysis of the processes is presented with a focus on minimizing energy consumption and capital expenditure. Furthermore, a sensitivity analysis is presented to identify key cost drivers and optimize holistic process operating conditions.
Dual function materials (DFMs) comprised of 0.25 %Ru, 6.1 %Na 2 O/γ-Al 2 O 3 //monolith were evaluated for about 250 hours time-on-stream (TOS) at various simulated ambient climate capture conditions followed by temperature swing methanation to 280 °C. Herein this paper focuses on the impact of thrifting Ru to low levels and the impact on performance. Results showed both stable CO 2 capture capacity and CH 4 production with 0.25 % Ru DFM deposited on a ceramic monolith. The CO 2 conversion to CH 4 production was decreased slightly by the Ru decrease from 1 % to 0.25 %. The capture capacity decreased since a lower Ru content reduces the complete decomposition of the Na 2 CO 3 precursor producing fewer active adsorption sites (“Na 2 O”). The deployment of a low Ru DFM monolith would significantly decrease the overall capital cost and give more potential for a large-scale direct air capture and methanation (DACM) application.
With the aim of meeting the urgent demand for active anode materials (AAM) in energy storage systems, bio-based graphite (biographite) emerges as an affordable solution to de-risk the turbulent supply chain of critical minerals. Anode grade biographite requires high crystallinity and purity, which can be achieved by catalytic graphitization with iron, followed by acid washing. Therefore, a well-conceived process integration that recycles catalyst can be the starting point to commercialization. This study evaluates closed-loop catalyst recovery, and byproducts valorization scenarios through a technoeconomic framework to help understand the scale-up potential of biographite. For the acid washing, three reactors in series meet the required biographite purity at 99.95%. Iron and acid recovery can reduce material consumption and waste generation by ~95%, albeit at the expense of ~80% increase in capital costs. Recovery scenarios present similar capital and operational expenses, yielding minimum selling prices (MSP) near $6 kg-1 of biographite. Monte Carlo methodology reveals that feedstock price accounts for ~60% of MSP variance, followed by plant capacity ~20%. The likelihood of reaching a competitive profit margin of 30% in the U.S. AAM market sits at 85% average for recovery scenarios, and 103% when iron oxide is sold as byproduct. Additionally, an IRR >= 15% can be achieved for half of Monte Carlo simulations, representing promising early-stage results. Biographite production offers a strategic pathway to stabilize the anode market beyond China by integrating established technologies for a scalable, economically viable, and sustainable process. The role of catalyst recovery and byproducts utilization is critical for advancing the biomaterials industry.
Pyrolysis oil, often referred as bio-oil or biocrude, has attracted considerable attention because it has higher energy density and carbon content compared to the raw biomass. Using pyrolysis oil derived from low cost and underutilized biomass to produce renewable hydrocarbon fuels provides a viable link between the agriculture/forestry and (petro-) chemical industry. Co-processing bio-oil with vacuum gas oil (VGO) in petroleum refinery is appealing due to the relatively low capital requirement to retrofit refinery and the compatibility of fuel products with existing infrastructure. In order to implement co-processing, a petroleum refinery would need to consider several process modifications and therefore could be subject to varying levels of air permitting requirements based on bio-oil co-processing ratio, co-processing capacity in existing units, the amount of regulated pollutants expected to be emitted, among other factors. This analysis considers co-processing 5% (by weight) of raw bio-oil with VGO in the fluidized catalytic cracking (FCC) unit(s) in a petroleum refinery. We estimate the potential increase in emissions of regulated air pollutants resulting from the modifications required to implement bio-oil co-processing and evaluate the regulatory and permitting implications for three FCC size categories in the U.S. refineries, which could co-processes raw bio-oil to produce partially renewable transportation fuels. We also assess technically feasible emission control options petroleum refineries could adopt to avoid being subject to major source permitting requirements if the estimated increase in regulated air pollutant emission exceeds the applicable threshold for major modifications. Insights from our analysis can help overcome challenges and risks associated with timely obtaining air permits required to implement bio-oil co-processing in existing refineries. Our analysis also provides needed information for decision makers (e.g., local air quality agencies) to understand the potential air quality implications for retrofitting refineries to co-process bio-oil, particularly in areas with high concentration of petroleum refineries.
Here we demonstrate the proof-of-concept for microchannel reactive distillation for alcohol-to-jet application: combining ethanol/water separation and ethanol dehydration in one unit operation. Ethanol is first distilled into the vapor phase, converted to ethylene and water, and then the water co-product is condensed to shift the reaction equilibrium. Process intensification is achieved through rapid mass transfer—ethanol stripping from thin wicks using novel microchannel architectures—leading to lower residence time and improved separation efficiency. Energy savings are realized with integration of unit operations. For example, heat of condensing water can offset vaporizing ethanol. Furthermore, the dehydration reaction equilibrium shifts towards completion by immediate removal of the water byproduct upon formation while maintaining aqueous feedstock in the condensed phase. For aqueous ethanol feedstock (40% w ), 71% ethanol conversion with 91% selectivity to ethylene was demonstrated at 220 °C, 600 psig, and 0.28 h -1 wt hour space velocity. 2.7 stages of separation were also demonstrated, under these conditions, using a device length of 8.3 cm. This provides a height equivalent of a theoretical plate (HETP), a measure of separation efficiency, of ~3.3 cm. By comparison, conventional distillation packing provides an HETP of ~30 cm. Thus, 9.1× reduction in HETP was demonstrated over conventional technology, providing a means for significant energy savings and an example of process intensification. Finally, preliminary process economic analysis indicates that by using microchannel reactive distillation technology, the operating and capital costs for the ethanol separation and dehydration portion of an envisioned alcohol-to-jet process could be reduced by at least 35% and 55%, respectively, relative to the incumbent technology, provided future improvements to microchannel reactive distillation design and operability are made.
TDA developed and demonstrated a highly efficient pre-combustion carbon capture system. The overall objective of this work was to develop a new sorbent-based pre-combustion carbon capture technology for Integrated Gasification Combined Cycle (IGCC) power plants. In this project our goal was to demonstrate the techno-economic viability of the new technology by 1) demonstrating it in large-scale slipstream tests, and 2) carrying out a high fidelity engineering and cost analysis. TDA’s process used an advanced physical adsorbent that selectively removes CO 2 from coal-derived synthesis gas above the dew point of the gas at temperatures as high as 300°C. The sorbent consists of a mesoporous carbon whose surface was grafted with functional groups that remove CO 2 via a well-known acid-base interaction. As documented in bench-scale experiments and field tests with actual coal gas, the sorbent achieved a very high capacity for CO 2 at temperatures as high as 300°C. The sorbent bound CO 2 more strongly than common physical adsorbents, providing the chemical potential needed for the high temperature operation. However, because CO 2 does not form a true covalent bond with the surface sites (as is the case with chemical absorbents), the sorbent regeneration could be carried out with only a very small energy input. The heat input to regenerate our sorbent was only 4.9 kcal per mol of CO 2 , which is much lower than that for chemical absorbents (e.g., 29.9 kcal/mol CO 2 for sodium carbonate) and was similar to the requirements of physical solvents (e.g., 4 kcal/mol CO 2 for Selexol TM ). Because the sorbent operates above the dew point of the synthesis gas (unlike the Selexol TM process), a higher power cycle efficiency can be achieved. With previous DOE/NETL funding (Contract No. DE-FE-0000469), we demonstrated the techno-economic viability of the technology in bench-scale tests and slipstream demonstrations at the National Carbon Capture Center (NCCC), Wilsonville, Alabama and Wabash River IGCC plant in Terra Haute, Indiana. We demonstrated a stable working CO 2 capacity for over 11,650 cycles with simulated synthesis gas. We also evaluated its performance with actual synthesis gas in two test campaigns at the Wabash River IGCC Plant, Terre Haute, IN and the National Carbon Capture Center (NCCC), Wilsonville, AL. The slipstream tests clearly showed that the actual coal gas constituents and potential contaminants (e.g. trace metals, halides, tars) had no effect on the sorbent’s ability to remove CO 2 (the same sorbent beds were used in both field tests with no sign of deactivation for 2,000 cycles with over 26,750 SCF of gas treated). As expected, due to the high temperature CO 2 removal capability and low energy needed to regenerate the sorbent, the power cycle efficiency with our process was greater than 34% on a higher heating value (HHV) basis; in comparison, the same IGCC plant equipped with the Selexol TM solvent for carbon capture can only achieve 31.4% HHV efficiency. The capital cost for an IGCC system with TDA’s process is estimated as $2,417/kW e , which is 12% lower than that of the IGCC/ Selexol TM process. The levelized cost for electricity including the transport, storage and monitoring (TS&M) cost for CO 2 was calculated as $\$ $92.9/MWh (lowest reported to our knowledge), which is much better than the $105.2/MWh estimated for the IGCC/ Selexol TM process. In this project (DE-FE0013105), TDA Research, in collaboration with our partners Gas Technology Institute (GTI), Illinois Clean Coal Institute (ICCI), University of California, Irvine (UCI), University of Alberta (UOA), Siemens, NCCC and Sinopec advanced the technical maturity of the technology; scaling it up by a factor of 100. We optimized the reactor design using computational fluid dynamics (CFD); using adsorption modeling we improved the pressure swing adsorption (PSA) cycle sequence. We carried out two field test campaigns with a fully-equipped 0.1 MW e prototype unit (for a total of 844 hours) using actual synthesis gas to prove the viability of the new technology. A successful 30 day (707 hrs) evaluation was completed at NCCC under air blown gasification conditions. We demonstrated 97.3% carbon capture at 1,500 SLPM, 93% carbon capture at 1,800 SLPM, and 90% carbon capture at 2,100 SLPM in the NCCC tests. We also demonstrated the system for 137 hours at a Sinopec petrochemical plant under oxygen blown gasification, demonstrating 86% carbon capture at 2,660 SLPM. In collaboration with University of California, Irvine (UCI), we completed a techno-economic analysis (TEA) for TDA’s warm gas cleanup technology integrated to IGCC power plant. The net plant efficiencies (on a coal HHV basis) for the warm gas cleanup cases were estimated to be 34.0% for E-GasTM gasifier, 34.4% for GE gasifier, 33.4 for the Shell gasifier and 34.2 for the TRIG TM gasifier (Cases 2, 4, 6 and 8 in this study) with a catalytic combustor for CO 2 purification, which are significantly higher than those for the Cold Gas Case, or an increase of as much as 12% in the heat rate for Case 2, 6% for Case 4, 9% for Case 6, and 9% for Case 8. The 1st year cost of electricity with the transport, storage and monitoring (TS&M) costs for the CO 2 included was $\$ $129.2/MWh for the E-GasTM gasifier Warm Gas Cleanup Case, $\$ $131.9/MWh for the GE gasifier Warm Gas Cleanup Case, $\$ $146.8/MWh for the Shell Gasifier Warm Gas Cleanup Case, and $\$ $129.9/MWh for the TRIG TM gasifier Warm Gas Cleanup Case. For comparison, the costs for the baseline Cold Gas CO 2 removal with Selexol for the different gasifiers were: $\$ $146.6/MWh for the E-Gas TM gasifier, $\$ $142.2/MWh for the GE gasifier, $\$ $159.0/MWh for the Shell gasifier and $\$ $144.3/MWh for the TRIG TM gasifier. In summary, the costs for our system were 7 to 12% lower than the corresponding Cold Gas Cleanup cases. The results of this techno-economic analysis suggested that TDA’s high temperature PSA-based Warm Gas Clean-up Technology can make a substantial improvement in the IGCC plant thermal performance for achieving near zero CO 2 emissions for E-Gas TM , GE, Shell and TRIG TM gasifier based IGCC power plants. The capital expenses were estimated to be lower than that of Selexol’s™. Taken together, the higher net plant efficiency and lower capital and operating costs resulted in substantial reduction in the cost of carbon capture for the IGCC plant equipped with TDA’s high temperature PSA-based carbon capture system. Finally, in collaboration with Gas Technology Institute (GTI) we completed the environmental health and safety assessment for TDA’s warm gas carbon capture technology.
The rapid rise in global plastic production in recent decades has resulted in the massive generation of plastic waste. Over 75% of the plastic waste generated in the United States was sent to landfills, with a meager 8.7% recycled. Plastics are valuable feedstocks for platform chemicals and fuels. Chemical upcycling of waste high-density polyethylene (HDPE) is gaining more attention as a potentially feasible and environmentally friendly plastic waste management technology. Conventional pyrolysis (CPY) and thermal oxo-degradation (TOD) are two chemical upcycling technologies actively researched for decomposing waste HDPE into valuable chemicals and fuels. However, there are few studies on the techno-economic analysis (TEA) and life cycle assessment (LCA) of these technologies for converting waste HDPE to valuable products. This study conducts a comparative TEA and LCA study of the thermochemical decomposition of waste HDPE to produce gaseous (ethylene and propylene) and liquid (naphtha, diesel, and wax) products by CPY and TOD. The study elucidates and compares the impact of hydrocracking longer chain hydrocarbons to produce more valuable products on the TEA and LCA. The TEA showed that the fixed capital investment could range from $\$32.5$ million for TOD without hydrocracking to $\$244$ million for CPY with hydrocracking scenarios. Annual revenues range from $\$28.1$ million to $\$71.5$ million in favor of scenarios with hydrocracking. However, the net present value ranges from $\$1.4$ million to $\$265.8$ million in favor of scenarios without hydrocracking. Sensitivity analysis showed that fixed capital cost, facility capacity, and product prices have the biggest impact on the process economics of the facilities, while utilities and waste transportation to refineries have the biggest impact on environmental impacts. Here, the LCA showed that primary products from scenarios without hydrocracking can be more environmentally friendly than virgin products from petroleum processes. However, TOD and CPY with hydrocracking primary products have more emissions than those of virgin products.
Propylene is an important petrochemical that is used in various industries, including the automobile and polymer sectors. Conventionally, propylene has been produced through fluid catalytic cracking, steam cracking, and propane dehydrogenation. In this project, a novel process to produce propylene from polypropylene plastic waste using a microwave reactor is introduced. Propylene production is simulated in Aspen Plus for both the conventional propane dehydrogenation process and the novel design, with heat integration applied to minimize utility demands and the conventional process serving as the base case for comparison. Finally, a tailored technoeconomic analysis is carried out for both simulated cases to estimate important economic indicators. Analysis of the results shows that the novel microwave-assisted process outperforms the conventional route for propylene production, achieving a single-pass conversion of almost 100%, compared with only 33.8% in the conventional plant. The Net Present Value of the novel plant is $\$1720.3$ MM, which is 3.5 times higher than the conventional process, while the Levelized Cost of Propylene is reduced by 40%. Capital and operating expenditure are also improved in the proposed scheme, with reductions of approximately $\$29$ MM and $\$222$ MM/yr, respectively. In addition to cost savings, this novel process also provides a convenient means to recycle waste polypropylene.