Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attainable yield”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

An eigenvalue method for solving transient heat conduction problems

The eigenvalue method, which has been used by researchers in structure mechanics, is applied to problems in heat conduction. Its formulation is decribed in terms of an examination of transient heat conduction in a square slab. Taking advantage of the availability of the exact solution, we compare the accuracy and other numerical properties of the eigenvalue method with those of existing numerical schemes. The comparsion shows that, overall, the eigenvalue method appears to be fairly attractive. Furthermore, only a few dominant eigenvalues and their corresponding eigenvectors need to be computed and retained to yield reasonably high accuracy. Greater savings are attained in the computation time for a transient problem with long time duration and a large computational domain.

Shih, T. M.↗
NASA NTRS1988

The heating environment during Martian atmospheric descent

It has been shown that a vehicle with a lift/drag ratio of 2.3 entering the Martian atmosphere at parabolic speed of 5 km/sec, or from a low orbit at 3.5 km/sec, has a very large landing footprint. At the 5-km/sec entry speed, the trajectory exhibits large skipping motions; however, a lateral range of up to 3300 km is attainable. The entries from low satellite orbit yield a gliding lateral range of 2500 km. The distances correspond to latitude changes of 57 and 42 deg, respectively. The high-speed, skipping entries were accompanied by the most intense heating. The peak stagnation point convective rates varied from 59 W/sq cm to 88 W/sq cm for partially and fully catalytic walls, respectively; the corresponding equilibrium wall temperatures were 1900 K and 2100 K. The peak heating at a wing leading-edge point reached 50 W/sq cm because of the presence of a transitional boundary layer. The lower-speed, gliding entries experienced much milder heating with a peak stagnation point rate of about 14 W/sq cm, resulting in a wall temperature near 1300 K. However, the longer duration of the gliding entries resulted in comparable heat loads for both entry speeds. The highest heat loads approached values experienced by the Shuttle orbiter stagnation point during a typical entry.

Tauber, Michael E.↗
NASA NTRS2007

Automated Target Planning for FUSE Using the SOVA Algorithm

The SOVA algorithm was originally developed under the Resilient Systems and Operations Project of the Engineering for Complex Systems Program from NASA s Aerospace Technology Enterprise as a conceptual framework to support real-time autonomous system mission and contingency management. The algorithm and its software implementation were formulated for generic application to autonomous flight vehicle systems, and its efficacy was demonstrated by simulation within the problem domain of Unmanned Aerial Vehicle autonomous flight management. The approach itself is based upon the precept that autonomous decision making for a very complex system can be made tractable by distillation of the system state to a manageable set of strategic objectives (e.g. maintain power margin, maintain mission timeline, and et cetera), which if attended to, will result in a favorable outcome. From any given starting point, the attainability of the end-states resulting from a set of candidate decisions is assessed by propagating a system model forward in time while qualitatively mapping simulated states into margins on strategic objectives using fuzzy inference systems. The expected return value of each candidate decision is evaluated as the product of the assigned value of the end-state with the assessed attainability of the end-state. The candidate decision yielding the highest expected return value is selected for implementation; thus, the approach provides a software framework for intelligent autonomous risk management. The name adopted for the technique incorporates its essential elements: Strategic Objective Valuation and Attainability (SOVA). Maximum value of the approach is realized for systems where human intervention is unavailable in the timeframe within which critical control decisions must be made. The Far Ultraviolet Spectroscopic Explorer (FUSE) satellite, launched in 1999, has been collecting science data for eight years.[1] At its beginning of life, FUSE had six gyros in two IRUs and four reaction wheels. Over time through various failures, the satellite has been left with one reaction wheel on the vehicle skew axis and two gyros. To remain operational, a control scheme has been implemented using the magnetic torque rods and the remaining momentum wheel.[2] As a consequence, there are attitude regions where there is insufficient torque authority to overcome environmental disturbances (e.g. gravity gradient torques). The situation is further complicated by the fact that these attitude regions shift inertially with time as the spacecraft moves through earth s magnetic field during the course of its orbit. Under these conditions, the burden of planning targets and target-to-target slew maneuvers has increased significantly since the beginning of the mission.[3] Individual targets must be selected so that the magnetic field remains roughly aligned with the skew wheel axis to provide enough control authority to the other two orthogonal axes. If the field moves too far away from the skew axis, the lack of control authority allows environmental torques to pull the satellite away from the target and can potentially cause it to tumble. Slew maneuver planning must factor the stability of targets at the beginning and end, and the torque authority at all points along the slew. Due to the time varying magnetic field geometry relative to any two inertial targets, small modifications in slew maneuver timing can make large differences in the achievability of a maneuver.

Heatwole, Scott↗
NASA NTRS1974

Optimal and suboptimal control technique for aircraft spin recovery

An analytic investigation has been made of procedures for effecting recovery from equilibrium spin conditions for three assumed aircraft configurations. Three approaches which utilize conventional aerodynamic controls are investigated. Included are a constant control recovery mode, optimal recoveries, and a suboptimal control logic patterned after optimal recovery results. The optimal and suboptimal techniques are shown to yield a significant improvement in recovery performance over that attained by using a constant control recovery procedure.

Young, J. W.↗
NASA NTRS1996

Vibrating Systems with Singular Mass-Inertia Matrices

Vibrating systems with singular mass-inertia matrices arise in recent continuum models of Smart Structures (beams with PZT strips) in assessing the damping attainable with rate feedback. While they do not quite yield 'distributed' controls, we show that they can provide a fixed nonzero lower bound for the damping coefficient at all mode frequencies. The mathematical machinery for modelling the motion involves the theory of Semigroups of Operators. We consider a Timoshenko model for torsion only, a 'smart string,' where the damping coefficient turns out to be a constant at all frequencies. We also observe that the damping increases initially with the feedback gain but decreases to zero eventually as the gain increases without limit.

Balakrishnan, A. V.↗
NASA NTRS2006

Estimating Resolution Lengths of Hybrid Turbulence Models

A two-stage procedure has been devised for estimating the spatial resolution achievable in the simulation of a given flow on a given computational grid by a computational fluid dynamics (CFD) code that incorporates a hybrid model of turbulence. The hybrid models to which this procedure is especially relevant are those of the Reynolds-averaged Navier-Stokes (RANS) and the partial-averaged Navier-Stokes (PANS) approaches. This procedure represents the first step toward adding variable-resolution turbulence-modeling capabilities to CFD codes as part of a continuing effort to increase the accuracy and robustness of CFD simulations of unsteady flows. Some background information is prerequisite to a meaningful summary of the procedure. Among experts in CFD, it is well known that combination of the Reynolds-averaged Navier-Stokes (RANS) approach and eddy-viscosity turbulence models offers limited capability for simulating unsteady and complex flows. The RANS approach includes an assumption that most of the energy in a given flow is modeled through turbulence-transport equations and is resolved in a computational grid used to simulate the flow. RANS also overpredicts eddy viscosity, thereby yielding excessive damping of unsteady motion. The eddy viscosity attains an unphysically large value because of unresolved scales, and suppresses most temporal and spatial fluctuations in the resolved flow field. One approach used to overcome this deficiency is to provide a mechanism for the RANS equations to resolve motion only on the largest scales and to use a hybrid model to represent effects at smaller scales. The RANS approach involves the use of a standard two-equation turbulence model in which the effect of turbulence is summarized by a viscosity that is a function of (1) the time-averaged kinetic- energy density (k) associated with the local fluctuating (turbulent) component of flow and (2) the time-averaged rate of dissipation of the turbulent-kinetic- energy density ( ). In PANS, which was developed to overcome the grid dependency associated with other hybrid turbulence models (including that of RANS), the standard two-equation turbulence model is replaced by another two-equation model in which one solves for the previously unresolved k and , which are now allowed to vary in space and time.

Abdol-Hamid, Khaled S.↗
NASA NTRS2012

Theory of a Traveling Wave Feed for a Planar Slot Array Antenna

Planar arrays of waveguide-fed slots have been employed in many radar and remote sensing applications. Such arrays are designed in the standing wave configuration because of high efficiency. Traveling wave arrays can produce greater bandwidth at the expense of efficiency due to power loss in the load or loads. Traveling wave planar slot arrays may be designed with a long feed waveguide consisting of centered-inclined coupling slots. The feed waveguide is terminated in a matched load, and the element spacing in the feed waveguide is chosen to produce a beam squinted from the broadside. The traveling wave planar slot array consists of a long feed waveguide containing resonant-centered inclined coupling slots in the broad wall, coupling power into an array of stacked radiating waveguides orthogonal to it. The radiating waveguides consist of longitudinal offset radiating slots in a standing wave configuration. For the traveling wave feed of a planar slot array, one has to design the tilt angle and length of each coupling slot such that the amplitude and phase of excitation of each radiating waveguide are close to the desired values. The coupling slot spacing is chosen for an appropriate beam squint. Scattering matrix parameters of resonant coupling slots are used in the design process to produce appropriate excitations of radiating waveguides with constraints placed only on amplitudes. Since the radiating slots in each radiating waveguide are designed to produce a certain total admittance, the scattering (S) matrix of each coupling slot is reduced to a 2x2 matrix. Elements of each 2x2 S-matrix and the amount of coupling into the corresponding radiating waveguide are expressed in terms of the element S11. S matrices are converted into transmission (T) matrices, and the T matrices are multiplied to cascade the coupling slots and waveguide sections, starting from the load end and proceeding towards the source. While the use of non-resonant coupling slots may provide an additional degree of freedom in the design, resonant coupling slots simplify the design process. The amplitude of the wave going to the load is set at unity. The S11 parameter, r of the coupling slot closest to the load, is assigned an arbitrary value. A larger value of r will reduce the power dissipated in the load while increasing the reflection coefficient at the input port. It is now possible to obtain the excitation of the radiating waveguide closest to the load and the coefficients of the wave incident and reflected at the input port of this coupling slot. The next coupling slot parameter, r , is chosen to realize the excitation of that radiating waveguide. One continues this process moving towards the source, until all the coupling slot parameters r and hence the S11 parameter of the 4-port coupler, r, are known for each coupling slot. The goal is to produce the desired array aperture distribution in the feed direction. From an interpolation of the computed moment method data for the slot parameters, all the coupling slot tilt angles and lengths are obtained. From the excitations of the radiating waveguides computed from the coupling values, radiating slot parameters may be obtained so as to attain the desired total normalized slot admittances. This process yields the radiating slot parameters, offsets, and lengths. The design is repeated by choosing different values of r for the last coupling slot until the percentage of power dissipated in the load and the input reflection coefficient values are satisfactory. Numerical results computed for the radiation pattern, the tilt angles and lengths of coupling slots, and excitation phases of the radiating waveguides, are presented for an array with uniform amplitude excitation. The design process has been validated using computer simulations. This design procedure is valid for non-uniform amplitude excitations as well.

Rengarajan, Sembiam↗
NASA NTRS1975

Effect of crack initiation, stable crack growth and unstable crack propagation on the crack-tip plastic zone

A technique for measuring the plastic zones associated with initial crack-tip yielding, subcritical crack growth, and unstable fracture is discussed. The results of the measurement of the locus of these yield regions, on center-cracked sheet and compact tension specimens of 7075-T6, 7075-T651, and 2024-T3 aluminum, are reported in this paper. It was found that a very accurate representation of the strains was obtained by this method and that the results added significant insight into the fracture process. The plastic zones were found to be approximately eight times wider in 2024-T3 than in the 7075-T6 sheets. The yield zones approached a maximum value after unstable fracture was attained and maintained that size through the fast fracture region. As expected, the plastic zones in the compact tension specimen were associated only with the formation of the shear lips and no plastic zones were observed in the fatigue precracked regions of either the center-cracked or compact-tension specimens.

Poulose, P. K.↗
NASA NTRS1982

Superconducting gravimeter

The superconducting gravimeter was developed and applied to field measurements. The stability of the instrument yielded the highest precision measurements of the Earth tides ever attained. It revealed unprecedented details about the effect of the atmosphere on gravity. Secular variations in gravity and the stability of the instruments were measured by comparing records from co-located instruments. These efforts have resulted in substantial reductions in the noise level at very low frequencies so that the peak differences between two instruments at the same location can be reduced to 0.1 micron gal.

Goodkind, J. M.↗
NASA NTRS2007

Observed and Modeled HOCl Profiles in the Midlatitude Stratosphere: Implication for Ozone Loss

Vertical profiles of stratospheric HOCl calculated with a diurnal steady-state photochemical model that uses currently recommended reaction rates and photolysis cross sections underestimate observed profiles of HOCl obtained by two balloon-borne instruments, FIRS-2 (a far-infrared emission spectrometer) and MkIV (a mid-infrared, solar absorption spectrometer). Considerable uncertainty (a factor of two) persists in laboratory measurements of the rate constant (k(sub 1)) for the reaction ClO + HO2 yields HOCl + O2. Agreement between modeled and measured HOCl can be attained using a value of k(sub 1) from Stimpfle et al. (1979) that is about a factor-of-two faster than the currently recommended rate constant. Comparison of modeled and measured HOCl suggests that models using the currently recommended value for k(sub 1) may underestimate the role of the HOCl catalytic cycle for ozone depletion, important in the midlatitude lower stratosphere.

temperature dependence↗
NASA NTRS1993

An electrorheologically controlled semi-active landing gear

This study is to explore the application of electrorheology (ER) to the real-time control of damping forces that are transmitted through the nose landing gear for an F-106B aircraft. The main part of the landing gear is a strut that consists of a pneumatic spring and an ER controlled damper that is situatted on the strut centerline and applies a force directly opposing the vertical displacement of the nose wheel. The damping element rotates in response to strut displacement, employing a co-axial arrangement of stator and rotor plates connected to the opposing electrodes in the control circuit. The vertical displacement is conveted into rotation of the damper through a screw-nut mechanism. The ER fluid between the electrodes is thus engaged in shear along circumferential lines of action. This design results in a fast time response and a high ratio of strut forces achieved under Er-vs. zero-field control. Compact size and simplicity in fabrication are also attained. The analysis shows that when using an ER fluid of a yield stress of 7kPa, the energy absorption efficiency of the landing gear can reach almost 100% at various sink rates.

Lou, Zheng↗
NASA NTRS2016

Additive Manufacturing of Multifunctional Components Using High Density Carbon Nanotube Yarn Filaments

Additive manufacturing allows for design freedom and part complexity not currently attainable using traditional manufacturing technologies. Fused Filament Fabrication (FFF), for example, can yield novel component geometries and functionalities because the method provides a high level of control over material placement and processing conditions. This is achievable by extrusion of a preprocessed filament feedstock material along a predetermined path. However if fabrication of a multifunctional part relies only on conventional filament materials, it will require a different material for each unique functionality printed into the part. Carbon nanotubes (CNTs) are an attractive material for many applications due to their high specific strength as well as good electrical and thermal conductivity. The presence of this set of properties in a single material presents an opportunity to use one material to achieve multifunctionality in an additively manufactured part. This paper describes a recently developed method for processing continuous CNT yarn filaments into three-dimensional articles, and summarizes the mechanical, electrical, and sensing performance of the components fabricated in this way.

Gardner, John M.↗
NASA NTRS1980

The relative stress-corrosion-cracking susceptibility of candidate aluminum-lithium alloys for aerospace structural applications

The microstructure and tensile properties of two powder metallurgy processed aluminum-lithium alloys were determined. Strength properties of 480 MPa yield and 550 MPa ultimate tensile strength with 5% strain to fracture were attained. Very little reduction in area was observed and fracture characteristics were brittle. The magnesium bearing alloy exhibited the highest strength and ductility, but fracture was intergranular. Recrystallization and grain growth, as well as coarse grain boundary precipitation, occurred in Alloy 2. The fracture morphology of the two alloys differed. Alloy 1 fractured along a plane of maximum shear stress, while Alloy 2 fractured along a plane of maximum tensile stress. It is found that a fixed orientation relationship exists between the shear fracture plane and the rolling direction which suggests that the PM alloys are strongly textured.

Pizzo, P. P.↗
NASA NTRS1986

Orbit determination using dual crossing arc altimetry

Accurate knowledge of the position of an altimetric satellite is required for the altimeter range data to be effective in measuring ocean topography. This study addresses the use of high-precision altimeter data from NASA's TOPEX Mission in reducing the radial component of the orbit of the U.S. Navy's N-ROSS satellite. Simulated altimeter crossing arc residuals between the TOPEX and N-ROSS orbits are minimized using both geometric and dynamic techniques in an effort to reduce the N-ROSS radial error to a level comparable to that of TOPEX. Tracking of N-ROSS by the Navy's NAVSPASUR system is simulated, and crossover residuals are created from the TOPEX and N-ROSS orbits. A simple geometric fit is shown to reduce the radial component of the NAVSPASUR N-ROSS orbit error from 350 m RMS to below 10 m RMS. In comparison, the dynamic approach of estimating the initial conditions of the N-ROSS orbit using a twentieth degree and order gravity field and a combined data set of tracking and altimeter crossover data yields a 6 m RMS residual error. Sub-meter accuracy can be attained by geometrically fitting these residuals to remove long wavelength orbit error.

Born, G. H.↗
NASA NTRS1996

Finite Difference Time Marching in the Frequency Domain: A Parabolic Formulation for Aircraft Acoustic Nacelle Design

An explicit finite difference iteration scheme is developed to study harmonic sound propagation in aircraft engine nacelles. To reduce storage requirements for large 3D problems, the time dependent potential form of the acoustic wave equation is used. To insure that the finite difference scheme is both explicit and stable, time is introduced into the Fourier transformed (steady-state) acoustic potential field as a parameter. Under a suitable transformation, the time dependent governing equation in frequency space is simplified to yield a parabolic partial differential equation, which is then marched through time to attain the steady-state solution. The input to the system is the amplitude of an incident harmonic sound source entering a quiescent duct at the input boundary, with standard impedance boundary conditions on the duct walls and duct exit. The introduction of the time parameter eliminates the large matrix storage requirements normally associated with frequency domain solutions, and time marching attains the steady-state quickly enough to make the method favorable when compared to frequency domain methods. For validation, this transient-frequency domain method is applied to sound propagation in a 2D hard wall duct with plug flow.

Baumeister, Kenneth J.↗
NASA NTRS1996

Finite Difference Time Marching in the Frequency Domain: A Parabolic Formulation for the Convective Wave Equation

An explicit finite difference iteration scheme is developed to study harmonic sound propagation in ducts. To reduce storage requirements for large 3D problems, the time dependent potential form of the acoustic wave equation is used. To insure that the finite difference scheme is both explicit and stable, time is introduced into the Fourier transformed (steady-state) acoustic potential field as a parameter. Under a suitable transformation, the time dependent governing equation in frequency space is simplified to yield a parabolic partial differential equation, which is then marched through time to attain the steady-state solution. The input to the system is the amplitude of an incident harmonic sound source entering a quiescent duct at the input boundary, with standard impedance boundary conditions on the duct walls and duct exit. The introduction of the time parameter eliminates the large matrix storage requirements normally associated with frequency domain solutions, and time marching attains the steady-state quickly enough to make the method favorable when compared to frequency domain methods. For validation, this transient-frequency domain method is applied to sound propagation in a 2D hard wall duct with plug flow.

Baumeister, K. J.↗
NASA NTRS2003

The Multipole Structure of Earth's STEP Signal

If there is an interaction in physical law which differentially accelerates the test bodies in a STEP satellite, then the di.erent elements that compose the Earth will most likely have source strengths for this interaction which are not proportional to their mass densities. The rotational flattening of Earth and geographical irregularities of our planet's crust then produces a multipole structure for the Equivalence Principle violating force field which differs from the multipole structure of Earth's ordinary gravity field. Measuring these differences yields key information about the new interaction in physical law which is not attainable by solely measuring differences of test body accelerations.

Nordtvedt, Kenneth↗
NASA NTRS1978

The Array Automated Assembly Task for the Low Cost Solar Array Project, Phase 2

During the program a process sequence was proposed and tested for the fabrication of dendritic welb silicon into solar modules. This sequence was analyzed as to yield and cost and these data suggest that the price goals of 1986 are attainable. Specifically, it was shown that a low cost POCL3 is a suitable replacement for the semiconductor grade, and that a suitable CVD oxide can be deposited from a silane/air mixture using a Silox reactor. A dip coating method was developed for depositing an antireflection coating from a metalorganic precursor. Application of photoresist to define contact grids was made cost effective through use of a dip coating technique. Electroplating of both Ag and Cu was shown feasible and cost effective for producing the conductive metal grids on the solar cells. Laser scribing was used to separate the cells from the dendrites without degradation. Ultrasonic welding methods were shown to be feasible for interconnecting the cells. A study of suitable low cost materials for encapsulation suggest that soda lime glass and phenolic filled board are preferred.

Campbell, R. B.↗