ZnTe-InAs heterojunctions
Fabrication and electrical properties of p-ZnTe/n-InAs heterojunctions obtained by interface alloying, suggesting p-i-n structure from characteristics and capacitance behavior
Baker, W. D.↗
SEARCH · Engineering Papers
Results for “ZnTe”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Vibronic spectra of Cu(2+) in ZnTe
Infrared-absorption spectra of substitutional Cu(2+) ions in ZnTe have been measured at 4.6 K. Several distinct absorption peaks are observed between 800 and 2000/cm. Absorption peaks at 1002 and 1069/cm are identified as zero-phonon lines arising from 2T2-2E transitions. Between 1069 and 2000/cm, several sets of sharp absorption lines are seen to recur regularly at an interval of 210/cm, corresponding to the LO phonon energy. Within each set distinct vibronic sidebands that cannot be identified with critical-point energies of TA, LA, TO or LO phonon modes are observed. A dynamic Jahn-Teller effect, involving coupling between a single-phonon mode and the electronic states of the 2E level, is proposed to account for the observed spectra.
Volz, M. P.↗
Phase Diagram of HgTe -ZnTe Pseudobinary and Density, Heat Capacity, and Enthalphy of Mixing of Hg(sub 1-x)Zn(sub x)Te Pseudobinary Melts
In this article, the solidus temperatures of the Hg(sub 1-x) Zn(sub x)Te pseudobinary phase diagram for several compositions in the low x region were measured by differential thermal analysis and the HgTe-ZnTe pseudobinary phase diagram was constructed. The densities of two HgZnTe melts, x = 0.10 and 0.16, were determined by an in situ pycnometric technique in a transparent furnace over, respectively, 110 and 50 C ranges of temperature. The thermodynamic properties of the melts, such as the heat capacity and enthalpy of mixing, were calculated for temperatures between the liquidus and 1500 C by assuming an associated solution model for the liquid phase.
Su, Ching-Hua↗
In-Situ Optical Determination of Thermomechanical Properties of ZnSe and ZnTe Crystals
At temperatures above 1/2 T(sub m), the generation and movement of dislocations may result due to the load created by the weight of the crystal itself The deformation may be expected to increase the line defect density and may result in generation of low angle grain boundaries, especially in the regions of the crystal attached to the ampule. It has often been suspected that elimination of this effect in space can improve crystallinity of crystals grown under microgravity conditions, however, a direct experimental proof of such relation is still missing. In this work we have designed and built a system of in-situ optical detection and measurement of the mechanical deformations of a crystal wafer under its own weight, and studied the deformation effects as a function of temperature. The results of the measurements for ZnSe and ZnTe crystal wafers will be presented.
Burger, A.↗
Research and development of HgZnTe as an infrared material
Interfacial morphology and Fermi level pinning behavior at the interfaces of Al, Ag, and Pt with UHV-cleaved CdTe and ZnTe have been studied using X-ray and ultraviolet photoemission spectroscopies. Results are compared to metal/HgCdTe interface formation, where the weak HgTe bond and consequent ease of Hg loss strongly influence semiconductor disruption and metal-semiconductor intermising. For Al/CdTe, the strong Al-Te reaction yields a significantly more extensive Al-Te reacted region than has been observed for HgCdTe. The Al/ZnTe interface is observed to be more abrupt than Al/CdTe. The final Fermi level pinning positions, Ef-Evbm for Al, Ag, and Pt on p-type CdTe and p-ZnTe have been determined. Efi is found to be roughly the same for both CdTe and ZnTe, with the value for ZnTe lying approximately 0.2 eV closer to the VBM for all three metals. From these results, one would expect Schottky barriers of about the same height for these metals on p-CdTe and p-ZnTe; and also that, in principle, metal interfaces with the two alloys HgCdTe and HgZnTe would have the same properties. Comparisons and implications for electrical behavior of metal contacts to the alloys are discussed.
Wahi, A. K.↗
ZnGa 2 Te 4 thin-film absorbers for photoelectrochemical CO 2 reduction
Photoelectrochemical (PEC) carbon dioxide reduction reaction (CO 2 RR) has been considered as a promising route to convert and store solar energy into chemical fuels. It is crucial to find suitable photoelectrode materials that are photo-catalytically active and exhibit excellent photochemical stability. One of the promising contenders is ZnTe with the ∼2.26 eV band gap and prolonged stability under CO 2 RR PEC conditions. Herein, a new telluride based thin-film ZnGa 2 Te 4 photocathode with lower band gap and stronger visible light absorption compared to ZnTe is synthesized and characterized using a combinatorial sputtering technique. A two-step annealing method with excess Te supply is implemented to synthesize nearly stoichiometric ZnGa 2 Te 4 absorber material with a zincblende-derived tetragonal crystal structure confirmed by synchrotron X-ray and electron diffraction. Theoretical calculations show that ZnGa 2 Te 4 has suitable direct bandgap (∼1.86 eV) and high absorption coefficient ∼10 5 cm −1 , in agreement with experimentally prepared films. Transient absorption spectroscopy reveals the biexponential decay dynamics, with time constants, τ 1 ∼ 0.04, and τ 2 ∼ 0.65 μs in microsecond time scales and provides the optical transition pathways for this semiconductor thin film. PEC measurements show that the ZnGa 2 Te 4 photocurrent densities are comparable to the widely investigated ZnTe photocathodes or even surpass it under simulated sunlight condition. ZnGa 2 Te 4 samples demonstrate promising photoelectrochemical stability, maintaining consistent performance under illumination. The inclusion of diaryliodonium additive substantially increases its CO 2 RR selectivity to ∼60%. These findings open a new avenue for the synthesis of telluride-based thin-film photocathodes for further exploration and will motivate future research to integrate this potential photocathode material into PEC devices.
36 MATERIALS SCIENCE↗
Applied research on 2-6 compound materials for heterojunction solar cells
Several II-VI heterojunctions show promise for photovoltaic conversion of solar energy. The three of greatest interest are p-CdTe/n-CdS, p-CdTe/n-ZnSe, and p-ZnTe/n-CdSe. Several p-CdTe/n-CdS heterojunction cells have been prepared by close spaced transport deposition of p-CdTe on single crystal n-CdS, and by two source vacuum evaporation of n-CdS on single crystal p-CdTe. Both types of cells, in an experimental stage, are quite comparable, exhibiting values of quantum efficiency between 0.5 and 0.9, open circuit voltages between 0.50 and 0.66 V, fill factors between 0.4 and 0.6, and solar efficiencies up to 4 percent. Cells of p-ZnTe/n-CdSe have also been made by close spaced vapor transport deposition of n-CdSe on single crystal p-ZnTe.
Bube, R. H.↗
Vapor Growth and Characterization of ZnSeTe Solid Solutions
Six ZnSe(1-x)Te(x) crystals were grown by the physical vapor transport technique. For each of the source material compositions, x = 0.10, 0.20 and 0.30, two crystals were grown - one under the horizontal and the other under the vertical stabilized configurations. The axial and radial compositional uniformity were measured by precision density measurements, wavelength dispersive X-ray spectroscopy (WDS) and optical transmission mappings. The measured radial ZnTe content was quite uniform for all the grown crystals except the horizontally grown crystal for x = 0.30. The WDS results on this crystal indicated a core with uniform ZnTe content, about 0.38, surrounded by a thin region of high ZnTe content with x = 0.8. This feature was confirmed by the SEM back scattering electron images. For the three source compositions the axial compositional variations for the vertically grown crystals were more uniform than that for the horizontally grown crystals. The measured compositions in the crystals grown from source composition of x = 0.10 suggest that the transport mechanism in the system can not be interpreted by a simple one-dimensional diffusion limited model.
Su, Ching-Hua↗
Distribution of Copper States, Phases, and Defects across the Depth of a Cu-Doped CdTe Solar Cell
Copper has been used as a p-type dopant in cadmium telluride (CdTe) for decades. However, the density of Cu atoms in the finished device is much higher than that of holes, which means that most Cu atoms are not activated as acceptors during incorporation. Furthermore, studies have demonstrated that the distribution of copper (Cu) atoms across the device is highly inhomogeneous, with reports citing Cu substitution on Cd sites and segregation to grain boundaries. Fast diffusion along these boundaries and Cu accumulation at the CdTe/CdS interface have also been observed and validated computationally. These levels of inhomogeneity make it difficult to accurately characterize and correlate the performance with the nature of the Cu atomic species present. To address this challenge, we utilize X-ray microscopy and, specifically, nanoscale fluorescence-mode X-ray absorption near-edge structure to resolve the atomic Cu environment throughout the depth of the CdTe layer. Our results suggest that the majority of Cu atoms are in the form of Cu x Te phases (or similar local environments) near the ZnTe|CdTe interface, Cu x O phases in the CdTe absorber, and present in various oxidation states, including Cu 1+ and Cu 2+ , near the CdS/CdTe junction. Here this work also provides experimental evidence for the first time of the presence of CuS around the ZnTe|CdTe interface and the hypothesized Cu Cd -Cl i complex in the CdTe absorber.
14 SOLAR ENERGY↗
Two-dimensional forms of robust CO 2 reduction photocatalysts
Photoelectrocatalysts that use sunlight to power the CO 2 reduction reaction will be crucial for carbon-neutral power and energy-efficient industrial processes. Scalable photoelectrocatalysts must satisfy a stringent set of criteria, such as stability under operating conditions, product selectivity, and efficient light absorption. Two-dimensional materials can offer high specific surface area, tunability, and potential for heterostructuring, providing a fresh landscape of candidate catalysts. From a set of promising bulk CO 2 reduction photoelectrocatalysts, we screen for candidate monolayers of these materials, then study their catalytic feasibility and suitability. For stable monolayer candidates, we verify the presence of visible-light band gaps, check that band edges can support CO 2 reduction, determine exciton binding energies, and compute surface reactivity. We find visible light absorption for SiAs, ZnTe, and ZnSe monolayers, and that due to a lack of binding, CO selectivity is possible. We thus identify SiAs, ZnTe, and ZnSe monolayers as targets for further investigation, expanding the chemical space for CO 2 photoreduction candidates.
36 MATERIALS SCIENCE↗
Ion beam sputter deposited zinc telluride films
Zinc telluride is of interest as a potential electronic device material, particularly as one component in an amorphous superlattice, which is a new class of interesting and potentially useful materials. Some structural and electronic properties of ZnTe films deposited by argon ion beam sputter depoairion are described. Films (up to 3000 angstroms thick) were deposited from a ZnTe target. A beam energy of 1000 eV and a current density of 4 mA/sq. cm. resulted in deposition rates of approximately 70 angstroms/min. The optical band gap was found to be approximately 1.1 eV, indicating an amorphous structure, as compared to a literature value of 2.26 eV for crystalline material. Intrinsic stress measurements showed a thickness dependence, varying from tensile for thicknesses below 850 angstroms to compressive for larger thicknesses. Room temperature conductivity measurement also showed a thickness dependence, with values ranging from 1.86 x to to the -6/ohm. cm. for 300 angstrom film to 2.56 x 10 to the -1/ohm. cm. for a 2600 angstrom film. Measurement of the temperature dependence of the conductivity for these films showed complicated behavior which was thickness dependent. Thinner films showed at least two distinct temperature dependent conductivity mechanisms, as described by a Mott-type model. Thicker films showed only one principal conductivity mechanism, similar to what might be expected for a material with more crystalline character.
Gulino, D. A.↗
Ion beam sputter deposited zinc telluride films
Zinc telluride is of interest as a potential electronic device material, particularly as one component in an amorphous superlattice, which is a new class of interesting and potentially useful materials. Some structural and electronic properties of ZnTe films deposited by argon ion beam sputter deposition are described. Films (up to 3000 angstroms thick) were deposited from a ZnTe target. A beam energy of 1000 eV and a current density of 4 mA/sq cm resulted in deposition rates of approximately 70 angstroms/min. The optical band gap was found to be approximately 1.1 eV, indicating an amorphous structure, as compared to a literature value of 2.26 eV for crystalline material. Intrinsic stress measurements showed a thickness dependence, varying from tensile for thicknesses below 850 angstroms to compressive for larger thicknesses. Room temperature conductivity measurement also showed a thickness dependence, with values ranging from 1.86 x 10 to the -6th/ohm cm for 300 angstrom film to 2.56 x 10 to the -1/ohm cm for a 2600 angstrom film. Measurement of the temperature dependence of the conductivity for these films showed complicated behavior which was thickness dependent. Thinner films showed at least two distinct temperature dependent conductivity mechanisms, as described by a Mott-type model. Thicker films showed only one principal conductivity mechanism, similar to what might be expected for a material with more crystalline character.
Gulino, D. A.↗
HgCdTe versus HgZnTe - Electronic properties and vacancy formation energies
The alloy variation of the band gap and the electron and hole effective masses have been calculated for HgCdTe and HgZnTe. Band-gap bowing is larger in HgZnTe than in HgCdTe because of the larger bond length mismatch of HgTe and ZnTe; electron and hole effective masses are found to be comparable for the two alloys for a given band gap. The electron mobility was calculated in both alloys with contributions from phonon, impurity, and alloy scattering. Contributions to the E1 line width due to alloy and impurity scattering in Hg(0.7)Cd(03)Te have been calculated. Results of calculations of the vacancy formation energies in HgTe, ZnTe, and CdTe are discussed.
Berding, M. A.↗
Characterization of Cadmium-Zinc Telluride Crystals Grown by 'Contactless' PVT Using Synchrotron White Beam Topography
Crystals of Cd(1-x)Zn(x)Te grown by Physical Vapor Transport (PVT) using self-seeding 'contactless' techniques were characterized using synchrotron radiation (reflection, transmission, and Laue back-reflection X-ray topography). Crystals of low (x = 0.04) and high (up to x approx. = 0.4) ZnTe content were investigated. Twins and defects such as dislocations, precipitates, and slip bands were identified. Extensive inhomogeneous strains present in some samples were found to be generated by interaction (sticking) with the pedestal and by composition gradients in the crystals. Large (up to about 5 mm) oval strain fields were observed around some Te precipitates. Low angle grain boundaries were found only in higher ZnTe content (x greater than or equal to 0.2) samples.
Palosz, W.↗
Optical Characterization of Bulk ZnSeTe Solid Solutions
Optical characterization was performed on wafers sliced from crystals of ZnSe, ZnTe and ZnSe (sub 1-x) Te (sub x) (0 less than x less than 0.4) grown by physical vapor transport technique. The energy band gaps at room temperature were determined from optical transmission measurements on 11 wafers. The best fit to the band gap vs. composition, x, data gives a bowing parameter of 1.336 which is between the value of 1.23 determined previously on ZnSeTe bulk crystals by reflectivity and the value of 1.621 reported on epilayers by photoconductivity. Low-temperature photoluminescence (PL) spectra were measured on 6 samples. The spectra of ZnSe and ZnTe were dominated by near band edge emissions and no deep donor-acceptor pairs were observed. The PL spectrum exhibited a broad emission for each of the ZnSe (sub 1-x) Te (sub x) samples, 0.09 less than x less than 0.39. For x = 0.09, this emission energy is about 0.2eV lower than the band gap energy measured at low temperature. As x increases the energy discrepancy gradually decreases and reduces to almost zero at x = 0.4. The single broad PL emission spectra and the spectra measured as a function of temperature were interpreted to be associated with the exciton bound to Te clusters because of the high Te content in these samples.
Su, Ching-Hua↗
Optical Characterization of Bulk ZnSeTe Solid Solutions
Optical characterization was performed on wafers sliced from crystals of ZnSe, ZnTe, and ZnSe(1-x)Te(x)(0 less than x less than 0.4) grown by physical vapor transport. Energy band gaps at room temperature were determined from optical transmission measurements on 11 wafers. A best fit curve to the band gap versus composition x data gives a bowing parameter of 1.45. This number lies between the value of 1.23 determined previously on ZnSeTe bulk crystals and the value of 1.621 reported on ZnSeTe epilayers. Low-temperature photoluminescence (PL) spectra were measured on six samples. The spectra of ZnSe and ZnTe were dominated by near band edge emissions and no deep donor-acceptor pairs were observed. The PL spectrum exhibited a broad emission for each of the ZnSe(1-x)Te(x) samples, 0.09 less than x less than 0.39. For x=0.09, this emission energy is about 0.2 eV lower than the band gap energy measured at low temperature. As x increases the energy discrepancy gradually decreases and reduces to almost zero at x=0.4. The single broad PL emission spectra and the spectra measured as a function of temperature were interpreted as being associated with the exciton bound to Te clusters because of the high Te content in these samples.
Su, Ching-Hua↗
Origin of the Bandgap Bowing in ZNSe(1-x)Te(x) Alloys
Photomodulated reflection and optical absorption spectroscopies were used to measure the composition and hydrostatic pressure dependencies of interband optical transitions in ZnSe(1-x)Te(x) alloys. On the Te-rich side, the bandgap reduction and the reduction in the pressure dependence of the bandgap are well explained by the band anticrossing interaction between the ZnTe conduction band states and the Se localized state located at 2.85 eV above the valence band top of ZnTe. On the Se-rich side, an interaction between the degenerate Gamma valence bands of ZnSe and the localized Te state located at 0.1 eV above the valence band top of ZnSe is proposed to generate the bandgap reduction and the rapid increase of the spin-orbit splitting with increasing Te concentration. A linear interpolation between these two models accounts for the composition and pressure dependencies of the bandgap in the entire composition range.
Walukiewicz, W.↗
Crystal Growth of ZnSe and Related Ternary Compound Semiconductors by Vapor Transport
The objective of the project is to determine the relative contributions of gravity-driven fluid flows to the compositional distribution, incorporation of impurities and defects, and deviation from stoichiometry observed in the crystals grown by vapor transport as results of buoyance-driven convection and growth interface fluctuations caused by irregular fluid-flows. ZnSe and related ternary compounds, such as ZnSeS and ZnSeTe, were grown by vapor transport technique with real time in-situ non-invasive monitoring techniques. The grown crystals were characterized extensively to correlate the grown crystal properties with the growth conditions. The following are the research progress in the past two years. In-situ monitoring of partial pressure by optical absorption technique and visual observation of the growing crystal were performed during vapor growth of ZnSe. Low-temperature photoluminescence (PL) spectra and glow discharge mass spectroscopy (GDMS) were measured on ZnSe starting materials provided by various vendors and on bulk crystals grown from these starting materials by physical vapor transport (PVT) to study the effects of purification and contamination during crystal growth process. Optical characterization was performed on wafers sliced from the grown crystals of ZnSe, ZnTe and ZnSe(1-x),Te(x), (0<x<0.4). Energy band gaps at room temperature were determined from optical transmission measurements and a best fit curve to the band gap vs. composition, x, data gives a bowing parameter of 1.45. Low-temperature photoluminescence (PL) spectra of ZnSe and ZnTe were dominated by near band edge emissions and no deep donor-acceptor pairs were observed. The PL spectrum exhibited a broad emission for the ZnSe(1-x),Te(x), samples, 0.09<x<0.39. The single broad PL emission spectra and the spectra measured as a function of temperature were interpreted as being associated with the exciton bound to Te clusters because of the high Te content in these samples. To validate numerical codes, in-situ monitoring during the PVT of HgI2 was designed. Optical absorption spectra of the vapor phase over HgI2 were measured for wavelengths between 200 and 600nm at sample temperatures between 349 and 610K. The Beer's Law constants for 15 wavelengths between 200 and 440 nm were determined. From these constants the vapor pressure of HgI2 was established as a function of temperature for the liquid and the solid Beta-phases To characterize the growth conditions during the PVT growth of In-doped ZnSe the optical absorbance of the vapor phase over the In-Se system were measured and were used to obtain the partial pressures of Se2(g) and In2Se(g).
Su, Ching-Hua↗