SEARCH · Engineering Papers

Results for “Wing loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

DOE OSTI2014

Structural FEM analysis of the strut-to-fuselage joint of a two-seat composite aircraft

An analysis of a strut-to-fuselage joint is realized in order to evaluate the zones with a high probability of failure by means of a safety factor. The whole section is analyzed using the Finite Element Method (FEM) so as to estimate static resistance behavior, therefore it is necessary a numerical mock-up of the section, the mechanical properties of the Carbon-Epoxy (C-Ep) material, and to evaluate the applied loads. Results of the analysis show that the zones with higher probability of failure are found around the wing strut and the fuselage joint, with a safety factor lower than expected in comparison with the average safety factor used on aircrafts built mostly with metals.

42 ENGINEERING↗

DOE OSTI2023

Exploring the Performance Boundaries of a Small Reconfigurable Multi-Mission UAV through Multidisciplinary Analysis

The performance of a small reconfigurable unmanned aerial vehicle (UAV) is evaluated, combining a multidisciplinary approach in the computational analysis of additive manufactured structures, fluid dynamics, and experiments. Reconfigurable UAVs promise cost savings and efficiency, without sacrificing performance, while demonstrating versatility to fulfill different mission profiles. The use of computational fluid dynamics (CFD) in UAV design produces higher accuracy aerodynamic data, which is particularly important for complex aircraft concepts such as blended wing bodies. To address challenges relating to anisotropic materials, the Tsai–Wu failure criterion is applied to the structural analysis, using CFD solutions as load inputs. Aerodynamic performance results show the low-speed variant attains an endurance of 1 h, 48 min, whereas its high-speed counterpart is 29 min at a 66.7% higher cruise speed. Each variant serves different aspects of small UAS deployment, with low speed envisioned for high-endurance surveying, and high speed for long-range or time-critical missions such as delivery. The experimental and simulation results suggest room for design iteration, in wing area and geometry adjustments. Structural simulations demonstrated the need for airframe improvements to the low-speed configuration. This paper highlights the potential of reconfigurable UAVs to be useful across multiple industries, advocating for further research and design improvements.

42 ENGINEERING↗

DOE OSTI2016

Effect of Form of Chromium on Spinel Formation

A number of Hanford high level waste (HLW) streams contain sufficiently high concentrations of chromium for it to become the waste loading limiting component in the waste. Chromium has relatively low solubility in borosilicate glasses and leads to the formation of various crystal phases including spinels. The extent of crystal formation must be managed during melter processing to prevent operational issues and potential premature melter failure that can result from excessive accumulation of crystals in the melter. In previous work for the Department of Energy (DOE) Office of River Protection (ORP), high-waste loading glass formulations were developed for representative HLW streams that are high in chromium. Results from those studies suggested that there may be differences in the crystallization behavior between glasses prepared in crucible melts and those prepared in DuraMelter 100 (DM100) joule heated melter runs. Understanding the cause of those differences has the potential to lead to the development of methods to further increase waste loadings for high chromium HLW streams through control of the formation of chromium-bearing crystals. As noted previously, the potential causes include differences in the form of components in the batch, including the form of chromium, as well as redox effects. This report describes the results from work to elucidate the origins of the observed differences and to identify melter feed composition modifications to control the formation of chromium-bearing crystal phases. The work focused on determining the effects of the form of chromium and the concentrations of oxidants in feed batches on spinel crystallization. Also evaluated was the use of potential melter feed additives to influence the redox state of chromium in the melt and its effect on spinel crystallization. As described in the Test Plan for this work, the objectives were accomplished through a combination of crucible-scale tests, small-scale tests with additives to influence redox state, and melter tests. This work builds on previous work performed at the Vitreous State Laboratory (VSL) of The Catholic University of America (CUA) for ORP to increase the waste loadings and processing rates of HLW glass formulations.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2013

Testing of Optimized Bubbler Configuration for HLW Melter

The principal objective of this work was to determine the glass production rate increase and ancillary effects of adding more bubbler outlets to the current WTP HLW melter baseline. This was accomplished through testing on the HLW Pilot Melter (DM1200) at VSL. The DM1200 unit was selected for these tests since it was used previously with several HLW waste streams including the four tank wastes proposed for initial processing at Hanford. This melter system was also used for the development and optimization of the present baseline WTP HLW bubbler configuration for the WTP HLW melter, as well as for MACT testing for both HLW and LAW. Specific objectives of these tests were to: Conduct DM1200 melter testing with the baseline WTP bubbling configuration and as augmented with additional bubblers. Conduct DM1200 melter testing to differentiate the effects of total bubbler air flow and bubbler distribution on glass production rate and cold cap formation. Collect melter operating data including processing rate, temperatures at a variety of locations within the melter plenum space, melt pool temperature, glass melt density, and melter pressure with the baseline WTP bubbling configuration and as augmented with additional bubblers. Collect melter exhaust samples to compare particulate carryover for different bubbler configurations. Analyze all collected data to determine the effects of adding more bubblers to the WTP HLW melter to inform decisions regarding future lid re-designs. The work used a high aluminum HLW stream composition defined by ORP, for which an appropriate simulant and high waste loading glass formulation were developed and have been previously processed on the DM1200.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2012

HLW Melter Control Strategy Without Visual Feedback

Plans for the treatment of high level waste (HL W) at the Hanford Tank Waste Treatment and Immobilization Plant (WTP) are based upon the inventory of the tank wastes, the anticipated performance of the pretreatment processes, and current understanding of the capability of the borosilicate glass waste form. The WTP HLW melter design, unlike earlier DOE melter designs, incorporates an active glass bubbler system. The bubblers create active glass pool convection and thereby improve heat and mass transfer and increase glass melting rates. The WTP HLW melter has a glass surface area of 3.75 m 2 and depth of ~ 1.1 m. The two melters in the HLW facility together are designed to produce up to 7.5 MT of glass per day at 100% availability. Further increases in HL W waste processing rates can potentially be achieved by increasing the melter operating temperature above 1150°C and by increasing the waste loading in the glass product. Increasing the waste loading also has the added benefit of decreasing the number of canisters for storage.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2023

Intensive and extensive margins of the peak load: Measuring adaptation with mixed frequency panel data

In this work we investigate the response of daily electricity peak load to daily maximum temperatures across states in Europe and India. We propose a method that decomposes short- from medium/long-run effects, retains the high frequency nature of the load-weather covariation and treats economic growth as a modulating factor. By simultaneously exploiting variation in unexpected daily weather anomalies and decade-long climatic changes in each location we decompose transitory - intensive margin - adjustments from permanent - extensive margin - adjustments. We find that the shocks over the long-run differ substantially from the short-run dynamics. Furthermore, we find evidence that per capita income modulates the adjustments over the short- and long-run. We project that in response to climate change around 2050 the peak load may increase by up to 20%-30% in Southern Europe and in several states in India, depending on the degree of warming and the evolution of socio-economic conditions. Even with a limited scope to two world regions, we identify that the structure of the economy and differences in future income growth matter in shaping the adaptation to climate change. Our decomposition allows to identify how future weather anomalies can further amplify the relative increase associated to the shift in the climate norm. Assuming that the interannual variability of maximum temperatures follows the distribution observed in the past, we find a doubling of the impacts of climate change during the summer in Europe. Uncertainty around the distribution of future weather anomalies may lead to further unexpected peak load amplifications. Our results have important policy implications for power systems’ generation capacity, transmission and storage, as we show that the challenges to accommodate the peak load in days with extreme temperatures may substantially increase already around mid-century.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

DOE OSTI2015

High Waste Loading Glass Formulation Development for High-Sr HLW

This report describes work performed to develop and test new glass and feed formulations in order to increase waste loading and glass melting rates for Hanford HLW with high concentrations of strontium. Testing was designed to identify glass and melter feed formulations that optimize waste loading and waste processing rate while meeting all processing and product quality requirements.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2015

FAINT CO LINE WINGS IN FOUR STAR-FORMING (ULTRA)LUMINOUS INFRARED GALAXIES

We report the results of a search for large velocity width, low-intensity line wings—a commonly used signature of molecular outflows—in four low redshift (ultra)luminous infrared galaxies that appear to be dominated by star formation. The targets were drawn from a sample of fourteen targets presented in Chung et al., who showed the stacked CO spectrum of the sample to exhibit 1000 km s{sup −1}-wide line wings. We obtained sensitive, wide bandwidth imaging of our targets using the IRAM Plateau de Bure Interferometer. We detect each target at very high significance but do not find the claimed line wings in these four targets. Instead, we constrain the flux in the line wings to be only a few percent. Casting our results as mass outflow rates following Cicone et al. we show them to be consistent with a picture in which very high mass loading factors preferentially occur in systems with high active galactic nucleus contributions to their bolometric luminosity. We identify one of our targets, IRAS 05083 (VII Zw 31), as a candidate molecular outflow.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2025

Vitrification Testing of HLW with High Phosphate

Projections of the number of high level waste (HLW) canisters to be produced in the Hanford Tank Waste Treatment and Immobilization Plant (WTP) (e.g., [1]) are based upon the inventory of the tank wastes, the anticipated performance of the sludge treatment processes, and current understanding of the capability of the borosilicate glass waste form. The WTP HLW melter design, unlike earlier Department of Energy (DOE) melter designs, incorporates a glass bubbler system. The bubblers create active glass pool mixing and thereby improve heat and mass transfer and glass melting rate. The WTP HLW melters each have a glass surface area of 3.75 m 2 and depth of ~1.1 m. The two melters in the HLW facility together are designed to produce up to 7.5 MT of glass per day at 100% availability. Further increases in HLW waste processing rates can potentially be achieved by optimization of the feed and glass formulations, increasing the melter operating temperature above 1150⁰C, and by increasing the waste loading in the glass product. Increasing the waste loading also has the added benefit of decreasing the number of canisters for storage.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2014

Dynamic load balance scheme for the DSMC algorithm

The direct simulation Monte Carlo (DSMC) algorithm, devised by Bird, has been used over a wide range of various rarified flow problems in the past 40 years. While the DSMC is suitable for the parallel implementation on powerful multi-processor architecture, it also introduces a large load imbalance across the processor array, even for small examples. The load imposed on a processor by a DSMC calculation is determined to a large extent by the total of simulator particles upon it. Since most flows are impulsively started with initial distribution of particles which is surely quite different from the steady state, the total of simulator particles will change dramatically. The load balance based upon an initial distribution of particles will break down as the steady state of flow is reached. The load imbalance and huge computational cost of DSMC has limited its application to rarefied or simple transitional flows. In this paper, by taking advantage of METIS, a software for partitioning unstructured graphs, and taking the total of simulator particles in each cell as a weight information, the repartitioning based upon the principle that each processor handles approximately the equal total of simulator particles has been achieved. The computation must pause several times to renew the total of simulator particles in each processor and repartition the whole domain again. Thus the load balance across the processors array holds in the duration of computation. The parallel efficiency can be improved effectively. The benchmark solution of a cylinder submerged in hypersonic flow has been simulated numerically. Besides, hypersonic flow past around a complex wing-body configuration has also been simulated. The results have displayed that, for both of cases, the computational time can be reduced by about 50%.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2015

Experimental analysis of energy harvesting from self-induced flutter of a composite beam

Previous attempts to harvest energy from aeroelastic vibrations have been based on attaching a beam to a moving wing or structure. Here, we exploit self-excited oscillations of a fluttering composite beam to harvest energy using piezoelectric transduction. Details of the beam properties and experimental setup are presented. The effects of preset angle of attack, wind speed, and load resistance on the levels of harvested power are determined. The results point to a complex relation between the aerodynamic loading and its impact on the static deflection and amplitudes of the limit cycle oscillations on one hand and the load resistance and level of power harvested on the other hand.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2014

High Waste Loading Glass Formulation Development for High-Cr HLW, VSL-14R3060-1 (April 2014)

This report describes work performed to develop and test new glass and feed formulations with both high waste loadings and high melting rates for Hanford high level waste (HLW) with high concentrations of chromium. The testing was designed to identify glass and melter feed formulations that optimize waste loading and waste processing rate while meeting all processing and product quality requirements. The work included preparation and characterization of crucible melts to assess melt rate using a vertical gradient furnace system and testing with respect to properties that determine processability and product quality. The results from crucible-scale testing supported subsequent DM100 tests designed to further assess the enhanced glass and feed formulations with respect to processing rate and product quality. The DM100-BL, which is one of two DM100 melter systems installed at VSL, was selected as the platform for these tests due to its extensive previous use in processing rate determination for various HLW streams and glass compositions. This work builds on previous work performed at VSL for DOE to increase waste loadings in HLW glass formulations and processing rates. The testing was performed according to the Test Plan that was developed for this work.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2019

Filtered lifting line theory and application to the actuator line model

Lifting line theory describes the cumulative effect of shed vorticity from finite span lifting surfaces. In this work, the theory is reformulated to improve the accuracy of the actuator line model (ALM). This model is a computational tool used to represent lifting surfaces, such as wind-turbine blades in computational fluid dynamics. In ALM, blade segments are represented by means of a Gaussian body force distribution with a prescribed kernel size. Prior analysis has shown that a representation of the blade using an optimal kernel width $\unicode[STIX]{x1D716}^{opt}$ of approximately one quarter of the chord size results in accurate predictions of the velocity field and loads along the blades. Also, simulations have shown that use of the optimal kernel size yields accurate representation of the tip-vortex size and the associated downwash resulting in accurate predictions of the tip losses. In this work, we address the issue of how to represent the effects of finite span wings and tip vortices when using Gaussian body forces with a kernel size larger than the optimal value. This question is relevant in the context of coarse-scale large-eddy simulations that cannot afford the fine resolutions required to resolve the optimal kernel size. For this purpose, we present a filtered lifting line theory for a Gaussian force distribution. Based on the streamwise component of the vorticity transport equation, we develop an analytical model for the induced velocity resulting from the spanwise changes in lift force for an arbitrary kernel scale. The results are used to derive a subfilter-scale velocity model that is used to correct the velocity along the blade when using kernel sizes larger than $\unicode[STIX]{x1D716}^{opt}$ . Tests are performed in large-eddy simulation of flow over fixed wings with constant and elliptic chord distributions using various kernel sizes. Results show that by using the proposed subfilter velocity model, kernel-size independent predictions of lift coefficient and total lift forces agree with those obtained with the optimal kernel size.

17 WIND ENERGY↗

DOE OSTI2021

Bioinspired energy absorbing material designs using additive manufacturing

Nature provides many biological materials and structures with exceptional energy absorption capabilities. Few, relatively simple molecular building blocks (e.g., calcium carbonate), which have unremarkable intrinsic mechanical properties individually, are used to produce biopolymer-bioceramic composites with unique hierarchical architectures, thus producing biomaterial-architectures with extraordinary mechanical properties. Several biomaterials have inspired the design and manufacture of novel material architectures to address various engineering problems requiring high energy absorption capabilities. For example, the microarchitecture of seashell nacre has inspired multi-material 3D printed architectures that outperform the energy absorption capabilities of monolithic materials. Using the hierarchical architectural features of biological materials, iterative design approaches using simulation and experimentation are advancing the field of bioinspired material design. However, bioinspired architectures are still challenging to manufacture because of the size scale and architectural hierarchical complexity. Notwithstanding, additive manufacturing technologies are advancing rapidly, continually providing researchers improved abilities to fabricate sophisticated bioinspired, hierarchical designs using multiple materials. This review describes the use of additive manufacturing for producing innovative synthetic materials specifically for energy absorption applications inspired by nacre, conch shell, shrimp shell, horns, hooves, and beetle wings. Potential applications include athletic prosthetics, protective head gear, and automobile crush zones.

36 MATERIALS SCIENCE↗

DOE OSTI2017

Direct Vitrification of HLW [Final Report]

This report describes work performed to develop and test new glass and feed formulations to support the direct vitrification of High Level Waste (HLW) with minimal or no pretreatment. In the HLW direct feed option that is under consideration for early operations of the Hanford Tank Waste Treatment and Immobilization Plant (WTP), the pretreatment facility would be bypassed in order to support an earlier start-up of the vitrification facility. For HLW, this would mean that the ultrafiltration and caustic leaching operations that would otherwise have been performed in the pretreatment facility would either not be performed or would be replaced by an interim pretreatment function (in-tank leaching and settling, for example). These changes would likely affect glass formulations and waste loadings and have impacts on the downstream vitrification operations. The primary objective of the work described herein was to develop and identify HLW glass compositions and glass forming additive blends for vitrification of two optimized candidate HLW blends which have undergone little or no washing with no other pretreatment, while maintaining high waste loadings, high processing rates, and acceptable glass properties. This was accomplished through a combination of crucible-scale tests, vertical gradient furnace (VGF) tests, and confirmation tests on the DM100 melter system.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2017

Use of Groundwater Flow, Solute Transport, and Geochemical Modeling To Evaluate Long-Term Nitrate Plume Concentrations Following Phreatophyte Source Control - 17262

The Monument Valley, Arizona, Processing Site is a former uranium mill site within the Navajo Nation in northeastern Arizona. Milling activities between 1955 and 1968 resulted in contamination of groundwater in the shallow alluvium at the site. Remedial action was completed under Title I of the Uranium Mill Tailings Radiation Control Act of 1978. Site remediation activities between 1992 and 1994 removed surficial source material and other site-related contamination, but contamination of deeper soil, primarily by nitrate, remained between the excavation depth and the water table. Residual nitrate in these soils, from uranium ore processing at the mill, has continued to be a source of groundwater contamination. To evaluate the potential for native phreatophytes to control remaining source material, four-wing salt-bush and black grease-wood were planted in 2000 and 2005 within the footprints of the former tailings piles. The objectives of the plantings were to increase nitrate removal from soil water through root uptake and, because phreatophyte water usage is expected to equal or exceed annual precipitation, to halt nitrate loading to groundwater. Recent evaluation showed more than an 80% decrease in soil nitrate concentrations and no effective groundwater recharge in the planting area. Numerical groundwater flow, solute transport, and geochemical modeling were performed to evaluate the long-term response of the existing nitrate plume to the phreatophyte source control measures. This modeling will help determine if 100-year natural flushing is a viable compliance strategy for the nitrate plume. Results showed that nitrate concentrations in the alluvial aquifer are expected to drop below the standard of 10 mg/L as N in approximately 70 years as a result of the phreatophyte planting. Companion sensitivity analysis was also performed to better understand how uncertainty in groundwater flow model and solute transport model inputs would impact cleanup times. Even considering input uncertainty, nitrate concentrations are expected to reach the standard in the alluvial aquifer within 100 years. Recognizing that model predictions are not absolute, but represent the general potential for an event to occur, the model was used to identify key sampling locations to verify that the nitrate plume will attenuate as predicted. This evaluation identified locations that can be used to assess the viability of the modeling predictions within the next 50 years. If the source diminishes or no longer exists, modeling predicts that concentrations of nitrate and ammonium in these wells should show significant declines over the next 10-55 years. If downward concentration trends do not occur as predicted, other remedial strategies may need to be evaluated to meet groundwater standards within the specified 100-year duration. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2026

Direct vitrification of HLW: evaluation of candidate source tanks

The initial objective of the present work was to review Hanford HLW compositions to identify HLW streams that are good candidates for the HLW direct feed vitrification option. Another objective was to develop and identify HLW glass compositions and glass forming additive blends for vitrification of two HLW streams identified from the review that could be treated with little or no washing or other pretreatment and would be, therefore, good direct feed candidates. The HLW glass compositions and additive blends were developed to maintain high waste loadings, high processing rates, and acceptable product glass properties. This was accomplished through a combination of crucible-scale and DM100 melter system tests.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2019

Crashworthiness of a Composite Wing Section: Numerical Investigation of the Bird Strike Phenomenon by Using a Coupled Eulerian–Lagrangian Approach

Crashworthiness is defined as the capability of a structure to guarantee its occupants safety during a crash event. In the present work, the crashworthiness of a composite wing section, subjected to a bird strike event, has been investigated. Indeed, the mechanical behavior of the impacted wing section has been inspected by means of the FE code Abaqus/Explicit. The impact phenomenon has been numerically simulated with a coupled Eulerian–Lagrangian (CEL) approach. The impacted structure has been modeled considering a Lagrangian formulation, while a Eulerian one has been used to model the bird. Moreover, Eulerian–Lagrangian contacts are used for transfer the loads arising from the impact event to the Lagrangian structure. The proposed numerical model, capable to take into account the matrix and fiber traction and compression damages, uses a 3D finite element approach to better predict the deformations and the damages onset and propagation during the impact event. The numerical results, in terms of structural deformation and damage onset and propagation, have been obtained by considering different impact locations and different impact angles.

36 MATERIALS SCIENCE↗