Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WELDED JOINT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Investigation of weld joint detection capabilities of a coaxial weld vision system

This report describes the second phase of a series of evaluations of a vision-based welding control sensor for the Space shuttle Main Engine Robotic Welding System. The robotic welding system is presently under development at the Marshall Space Flight Center. This evaluation determines the factors influencing the minimum joint gap required for consistent detection of the weld joint.

Gangl, K. J.↗

Effect of Multiple Local Repairs on Microstructure and Mechanical Properties of T24 Steel Welded Joint

The effect of multiple local repairs on the microstructure and mechanical properties of the T24 steel welded joints was studied. T24 steel tubes were butt-welded by the GTAW method. Peripheral welded joints were made in four locations of the tube. In order to simulate the repair procedure, the welds were cut off from the root and the first local repair was performed. Other two local repairs were carried out in the same way. After each local repair, the microstructure and mechanical properties of the joints were evaluated. The results of the mechanical tests demonstrate that only two local repairs can be performed on the T24 steel peripheral welded joint. After the third local repair, impact energy of the welded joint was lower than required value, which is attributed to the coarser martensite and the coarser carbide precipitates formed in the heat-affected zone, compared with the weld metal.

36 MATERIALS SCIENCE↗

Microstructure, Chemical Composition and Local Corrosion Behavior of a Friction Stud Welding Joint

In this paper, friction stud welding technology was used to join a stud and base metal, which were composed of X65 steel. The scanning vibrating electrode technique (SVET) and localized electrochemical impedance spectroscopy (LEIS) were used to investigate the localized corrosion behaviors of the welded joint. Scanning electron microscopy, metallographic microscopy and a micro-hardness tester were used to observe the microstructure and measure the hardness of the welded sample. Raman spectrometry and energy-dispersive spectrometry were used to measure the composition of the weldment before and after corrosion, respectively. The results show that there are the maximum micro-hardness and the densest microstructure in the welded zone compared with the other zones. In addition, α-Fe{sub 2}O{sub 3} and Fe{sub 3}O{sub 4} are present in the welded zone. The SVET and LEIS data indicate that the welded zone has the lowest current density and the largest impedance due to the presence of iron oxides and the densest microstructure, thus showing the excellent corrosion resistance. The relationship among microstructure, micro-hardness, chemical composition and local electrochemical behavior was discussed.

36 MATERIALS SCIENCE↗

Plating To Reinforce Welded Joints

Electrodeposition used to strengthen welded joints gouged, nicked, or suffered other mechanical damage. Plating cell, typically of acrylic plastic such as poly (Methylmetacrylate), is assembled around part to be plated. Areas not to be plated are masked with plater's tape. Weld area is plated in standard nickel-plating process.

Otousa, J. E.↗

Characterization of Mechanical Properties and Residual Stress in API 5L X80 Steel Welded Joints

The use of high-strength and low-alloy steels, high design factors and increasingly stringent safety requirements have increased the operating pressure levels and, consequently, the need for further studies to avoid and prevent premature pipe failure. To evaluate the possibility of improving productivity in manual arc welding of this type of steel, this work characterizes the mechanical properties and residual stresses in API 5L X80 steel welded joints using the SMAW and FCAW processes. The residual stresses were analyzed using x-ray diffraction with the sin{sup 2}ψ method at the top and root of the welded joints in the longitudinal and transverse directions of the weld bead. The mechanical properties of the welded joints by both processes were characterized in terms of tensile strength, impact toughness and Vickers microhardness in the welded and shot peening conditions. A predominantly compressive residual stress was found, and shot peening increased the tensile strength and impact toughness in both welded joints.

36 MATERIALS SCIENCE↗

Influence of Aluminum Coatings on the Quality of Weld Joints

The application of a longitudinal magnetic field in welding aluminum coated sheet is considered. A special welding head is used to produce weld joints of satisfactory quality. Findings are obtained regarding the formation and metallographic structure of the metal in the seam, with the segregation of aluminum over its cross section. The formation of composite structure is noted.

42 ENGINEERING↗

Dissimilar Metal Weld Joints of P91/Ni Alloy: Microstructural Characterization of HAZ of P91 and Stress Analysis at the Weld Interfaces

Microstructure evolution and hardness were evaluated at the interface of two friction-welded transition joints between P91 and AISI 304 fabricated applying Inconel interlayers, viz. single-interlayer weld (P91/IN600/AISI304) and three-interlayer weld (P91/IN625/IN600/IN800H/AISI304). The welds were subjected to post-weld heat treatment at 1023 K for 1 h followed by air cooling and a long-term exposure at 973 K for 100, 250, and 500 h. A soft zone with the absence of lath martensite was noticed in both the welds which was located at the intercritical heat-affected zone of the welds. This zone was found to be extending with time toward the fine grain heat-affected zone by carbide precipitation and coarsening at the grain boundaries. Soft zone formation at the interface of the welds was found to be due to carbon diffusion. The presence of high-nickel-content alloy at the interface was proven to be beneficial in stopping carbon diffusion at the interface. Though soft zones existed in both the welds, better creep rupture life was observed for three-interlayer welds. Finite element analysis of these weld joints was performed for thermal loading followed by tensile loading. The results from this analysis indicated that thermal expansion also plays an important role in the failures of these dissimilar weld joints by creating high stress at the interface due to incompatibility.

36 MATERIALS SCIENCE↗

Investigation of Structure and Crack Formation in Welded Joints of Single Crystal Ni-Base Alloys

Conditions of initiation of hot cracks in welding of single crystal heat-resistant alloys with a 56% content of the γ’-phase were studied. Conditions for providing a polycrystalline structure in HAZ and part of the weld metal were artificially created in one region of a welded joint with the single crystal structure. Welding of the single crystal alloy was performed by the electron beam method in vacuum. Cracks in a low-temperature ductility dip range (ductility dip cracking) were found to form in HAZ and weld of a welded joint with the polycrystalline structure. The nature of cracking of the single crystal weld is related to formation of low-melting point eutectoid interlayers, as well as to exhausting of the safety factor for ductility. In conclusion, cracks in the single crystal weld along the strain grain boundaries are formed by a similar mechanism.

36 MATERIALS SCIENCE↗

Microstructure evolution of Al/Mg butt joints welded by gas tungsten arc with Zn filler metal

Based on the idea of alloying welding seam, Gas tungsten arc welding method with pure Zn filler metal was chosen to join Mg alloy and Al alloy. The microstructures, phases, element distribution and fracture morphology of welding seams were examined. The results indicate that there was a transitional zone in the width of 80-100 {mu}m between the Mg alloy substrate and fusion zone. The fusion zone was mainly composed of MgZn{sub 2}, Zn-based solid solution and Al-based solid solution. The welding seam presented distinct morphology in different location owning to the quite high cooling rate of the molten pool. The addition of Zn metal could prevent the formation of Mg-Al intermetallics and form the alloyed welding seam during welding. Therefore, the tensile strengths of joints have been significantly improved compared with those of gas tungsten arc welded joints without Zn metal added. Highlights: Black-Right-Pointing-Pointer Mg alloy AZ31B and Al alloy 6061 are welded successfully. Black-Right-Pointing-Pointer Zinc wire is employed as a filler metal to form the alloyed welding seam. Black-Right-Pointing-Pointer An alloyed welding seam is benefit for improving of the joint tensile strength.

36 MATERIALS SCIENCE↗

Cooling Environment Effect on the Microstructure and Mechanical Properties of Friction Stir-Welded Joints

The heat input in friction stir welding (FSW) influences the localized properties in welded joint. The external cooling during FSW reduces the localized heating and post-weld cooling time by extracting heat comparatively at a faster rate. In the present study, we have investigated the effect of different cooling environments on the performance of friction stir-welded (FSWed) AA5052 strain-hardenable aluminum alloy. Welding was performed under three different cooling environments such as natural air, water and liquid nitrogen in order to understand their effects on grain structure, metallurgical changes and mechanical properties of the joints. It has been noted that the width of weld nugget zone, thermo-mechanically affected zone and heat-affected zone has been decreased with the respective change in cooling environments. Welding speed could also influence the width of different zones in weldment alike the cooling environments. Finer grain size has been noticed with water cooling against the liquid nitrogen cooling. Comparatively, water was observed to be more favorable cooling environment against liquid nitrogen because of its better weld quality (97%) compared with base metal. The favorable mechanical properties resulting from the different weldment regions for different cooling environments have been elaborated in the present study.

36 MATERIALS SCIENCE↗

ASSESSING THE EFFECTIVENESS OF ULTRASONIC IMPACT TREATMENT ON RESIDUAL STRESS PROFILES IN DISSIMILAR WELDED JOINTS

Residual stresses (RS) induced during welding processes are a critical concern in materials engineering, as they can significantly impair the mechanical performance of components by reducing fatigue strength and tensile load capacity. This challenge is especially pronounced in dissimilar metal welds (DMWs), where variations in thermal expansion properties between the joined alloys exacerbate the formation of tensile RS. Conventional post-weld heat treatments, though effective for homogeneous materials, often require substantial energy, specialized equipment, and extensive processing time, making them less practical for DMW applications. Thus, there is a clear need for innovative, energy-efficient techniques to mitigate these detrimental stresses. This study investigates ultrasonic impact treatment (UIT) as a possible alternative for mitigating tensile RS in both similar and dissimilar metal welds. To evaluate UIT’s effectiveness, neutron diffraction (ND) was employed as a nondestructive technique to quantify RS in three orthogonal directions—longitudinal, transverse, and normal. The results showed that UIT significantly reduced peak tensile RS, particularly in the longitudinal direction, by up to 180 MPa in similar welds and up to 150 MPa in dissimilar welds. Given the limited literature on UIT application in DMWs, this work contributes valuable data on stress redistribution mechanisms and highlights UIT’s potential as a practical stress-relief method. The findings lay the groundwork for further investigations aimed at optimizing process parameters and understanding long-term performance in welded joints.

EisaZadeh, Hamid [Western Carolina University, Cul↗

Formation of Lamellar Carbides in Alloy 617-HAZ and Their Role in the Impact Toughness of Alloy 617/9%Cr Dissimilar Welded Joint

The relationship between the microstructure and impact toughness, especially the formation of the lamellar carbides and its effect on the impact toughness of the heat-affected zone of Alloy 617 (Alloy 617-HAZ), was systematically investigated. Impact test was performed on Alloy 617/9%Cr dissimilar welded joints aged for different time at 620 °C. The results showed that the characteristic zones of the whole welded joint revealed decreased impact toughness with increasing the aging time. The impact energies in weld metal showed high stability despite the aging process, while the Alloy 617-HAZ for all testing specimens presented the lowest impact toughness with various aging time. Meanwhile, the mixed grains were found in the base metal (BM) and heat-affected zone of Alloy 617, together with the twins with different widths located in the interior of the large grains. The columnar and equiaxed grain zones appear alternately due to the multilayer and multi-pass welding technique. In particular, compared with Alloy 617-BM, coarsened and even lamellar carbides were observed in Alloy 617-HAZ. These special carbides can separate the grains and therefore result in the formation of intergranular fracture morphology in Alloy 617-HAZ. Besides, the microhardness distribution was tested with a proper load, and the results exhibited that the weld possessed the highest hardness for all specimens with various aging time. The higher microhardness in Alloy 617-HAZ compared with that in Alloy 617-BM was attributed to the high density of the dislocations, which could be detected by transmission electron microscope. As a result, the coarsened carbides aggregated in the grain boundaries to form the lamellar layer are deemed as the main factor to reduce the impact toughness in Alloy 617-HAZ.

36 MATERIALS SCIENCE↗

Experimental study of cyclic creep and high-cycle fatigue of welded joints of St3 steel by the DIC technique

In the paper the mechanisms of plastic deformation and fracture of welded joints of steel St3 were investigated at high-cycle fatigue and cyclic creep by the digital image correlation (DIC) technique. The evolution of strain rate is studied for the following regions: base metal, HAZ, and fusion zone. This strain rate evolution can be considered as a mechanical response of material. Three stages of deformation evolution are shown: deformation hardening (I), fatigue crack initiation (II), and the last stage is related to main crack (III). Two criteria are offered to evaluate the current mechanical state of welded joints.

36 MATERIALS SCIENCE↗

Investigation of Hydrogen Embrittlement Susceptibility of X80 Weld Joints by Thermal Simulation

The objective of this study was to investigate the hydrogen embrittlement (HE) susceptibility and influence mechanism of X80 weld joints. Slow strain rate testing (SSRT) under in situ H-charging, combined with microstructure and fracture analysis, was performed on the base metal (BM), weld metal (WM), thermally simulated fine-grained heat-affected zone (FGHAZ) and coarse-grained heat-affected zone (CGHAZ). Results showed that the WM and simulated HAZ had a greater degree of high local strain distribution than the BM; compared to the CGHAZ, the FGHAZ had lower microhardness and more uniformly distributed stress. SSRT results showed that the weld joint was highly sensitive to HE; the HE index decreased in the following sequence: FGHAZ, WM, CGHAZ and BM. The effect of the microstructure on HE was mainly reflected in microstructure, local stress distribution and microhardness.

36 MATERIALS SCIENCE↗

Effect of Welding Parameters on Junction Structure and Fracture Behavior of Friction-Stir-Welded Joints of 2024 Aluminum Alloys

In this paper, the effect of welding speed and tool rotation speed on the junction structure and fracture behavior of friction-stir-welded joints was investigated with use of 2024 aluminum alloys of 3.2 mm thick. Results show that the formation of junction structure is more affected by tool rotation speed than by welding speed due to the differences of heat input levels. When welding speed is at 100 mm/min and tool rotation speed is in the range of 400-600 r/min, the joint junction structure causes complete bonding with no welding defects. While under improper welding parameters, the junction structure causes the precipitate aggregation on the bonding line and the partial bonding with the appearance of both tunnel defects and kissing bond defects. Meanwhile, the results of tensile tests show that the tensile fracture of all FSW joints occur at the weld center. The failure mode of joints with defects-free junction structure characterized by shear fracture is ductile. While the failure mode of joints with defects-existent junction structure characterized by layered fracture surface is brittle. Furthermore, that heterogeneous microstructure, precipitate aggregation and welding defects converge inside the junction structure is the main factor affecting the tensile properties and fracture behavior of the friction-stir-welded joint.

36 MATERIALS SCIENCE↗

Effect of long-term aging on microstructure and local behavior in the heat-affected zone of a Ni–Cr–Mo–V steel welded joint

Evolution of microstructure, micro-hardness and micro-tensile strength behavior was investigated in the heat-affected zone of a Ni–Cr–Mo–V steel welded joint after the artificial aging at 350 °C for 3000 h. After detailed characterization of microstructures in optical microscopy, scanning electron microscopy and transmission electron microscopy, it is revealed that the change of martensite–bainite constituent promotes more homogeneous microstructure distribution. The aging treatment facilitates redistribution of carbon and chromium elements along the welded joint, and the micro-hardness is increased slightly through the welds due to enrichment of carbon. The types of precipitates in the weldment mainly include M{sub 3}C, MC, M{sub 2}C and M{sub 23}C{sub 6}. The carbides in base metal, weld metal and coarse-grained heat-affected zone are prone to change from ellipsoidal to platelet form whereas more uniform spherical carbides are observed in the fine-grained zone. Precipitation and coarsening of M{sub 23}C{sub 6} near the fusion line, and formation of MC and M{sub 2}C, are responsible for the tensile strength decrease and its smooth distribution in the aged heat-affected zone. This implies that the thermal aging can relieve strength mismatch in the weldments. - Highlights: • Microstructure homogeneity improved in HAZ after long-term aging. • Tensile strength decreased in HAZ due to precipitation and coarsening of M{sub 23}C{sub 6}. • Strength mismatch in NiCrMoV steel welds was relieved after aging at 350 °C × 3000 h.

36 MATERIALS SCIENCE↗