SEARCH · Engineering Papers

Results for “Viscosity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS1983

The minimum mantle viscosity of an accreting earth

The minimum mantle viscosity in an earth accreting from planetesimals is estimated. A plausible distribution of planetesimal sizes deposits enough energy to melt the outer nine-tenths of earth's mass; however, vigorous convection keeps temperatures near the solidus. Viscosity is significantly lower than prevails now. The temperature-dependent viscosity provides self-regulation so there is a continuing balance between accretional energy input and heat transfer out. This allows calculation of the minimum viscosity necessary to transfer out heat by a Nu/Ra-number relation. Typical viscosities are 0.1 to a million sq m/sec, lowest at mid-accretion when the mass growth rate is largest. Terrestrial planets are compared, and minimum iron descent times to central lithospheres are calculated.

Cooperman, S. A.↗

NASA NTRS1985

Measurement and correlation of jet fuel viscosities at low temperatures

Apparatus and procedures were developed to measure jet fuel viscosity for eight current and future jet fuels at temperatures from ambient to near -60 C by shear viscometry. Viscosity data showed good reproducibility even at temperatures a few degrees below the measured freezing point. The viscosity-temperature relationship could be correlated by two linear segments when plotted as a standard log-log type representation (ASTM D 341). At high temperatures, the viscosity-temperature slope is low. At low temperatures, where wax precipitation is significant, the slope is higher. The breakpoint between temperature regions is the filter flow temperature, a fuel characteristic approximated by the freezing point. A generalization of the representation for the eight experimental fuels provided a predictive correlation for low-temperature viscosity, considered sufficiently accurate for many design or performance calculations.

Schruben, D. L.↗

NASA NTRS1986

Plasma viscosity elevations with simulated weightlessness

A hypothesis correlating an increase in blood viscosity during bed rest to a decrease in aerobic capacity during simulated weightlessness is tested. Eight human subjects were studied on the sixth day of bed rest during two consecutive 10-d bed rest periods separated by a 14-d recovery interval designed to simulate the flight-layover schedule of Shuttle astronauts. Plasma viscosity and volume were measured, together with maximal aerobic capacity (VO2max). An increase in hematocrit, plasma protein, and fibrinogen concentrations was found, contributing to an elevation in plasma viscosity. VO2max decreased significantly in the first, but not the second bed rest cycle, and though many individuals exhibited a decrease in plasma volume and aerobic capacity coupled with elevated plasma viscosity, correlations between these variables were lacking. It is concluded that the decrease in VO2max observed following simulated weightlessness cannot be attributed to alterations in muscle blood flow resulting from increased blood viscosity.

Martin, D. G.↗

NASA NTRS1987

Calculated viscosity-distance dependence for some actively flowing lavas

The importance of viscosity as a gauge of the various energy and momentum dissipation regimes of lava flows has been realized for a long time. Nevertheless, despite its central role in lava dynamics and kinematics, it remains among the most difficult of flow physical properties to measure in situ during an eruption. Attempts at reconstructing the actual emplacement viscosities of lava flows from their solidified topographic form are difficult. Where data are available on the position of an advancing flow front as a function of time, it is possible to calculate the effective viscosity of the front as a function of distance from the vent, under the assumptions of a steady state regime. As an application and test of an equation given, relevant parameters from five recent flows on Mauna Loa and Kilauea were utilized to infer the dynamic structure of their aggregate flow front viscosity as they advanced, up to cessation. The observed form of the viscosity-distance relation for the five active Hawaiian flows examined appears to be exponential, with a rapid increase just before the flows stopped as one would expect.

Pieri, David↗

NASA NTRS1987

The effect of a shallow low viscosity zone on the apparent compensation of midplate swells

A model for midplate swells is assumed where the swell topography is dynamically maintained by convection beneath a conducting lid. Using an idealized viscosity structure consisting of a low viscosity layer underneath the lid and overlying a constant viscosity region, the effect of the low viscosities, the layer thickness, and the Rayleigh number on the flow and on the inference of a compensation mechanism from the associated gravity, geoid, and topography anomalies is investigated. The calculations show that a simple plume model with stratified viscosity variations of less than two orders of magnitude near the surface can produce the range of depths of compensation seen at midplate swells. Shallow depths of compensation, therefore, cannot be used to argue against dynamic models for the formation of hot spot swells.

Robinson, Elizabeth M.↗

NASA NTRS1987

Quantitative characterization of the viscosity of a microemulsion

The viscosity of the three-component microemulsion water/decane/AOT has been measured as a function of temperature and droplet volume fraction. At temperatures well below the phase-separation temperature the viscosity is described by treating the droplets as hard spheres suspended in decane. Upon approaching the two-phase region from low temperature, there is a large (as much as a factor of four) smooth increase of the viscosity which may be related to the percolation-like transition observed in the electrical conductivity. This increase in viscosity is not completely consistent with either a naive electroviscous model or a simple clustering model. The divergence of the viscosity near the critical point (39 C) is superimposed upon the smooth increase. The magnitude and temperature dependence of the critical divergence are similar to that seen near the critical points of binary liquid mixtures.

Berg, Robert F.↗

NASA NTRS1988

The effect of a shallow low-viscosity zone on the mantle flow, the geoid anomalies and the geoid and depth-age relationships at fracture zones

A two-dimensional FEM is used to investigate the flow driven by the horizontal temperature gradient at a fracture zone and to calculate the resulting geoid and topography anomalies. Using a three-layered viscosity structure for the upper mantle, results are presented for the effects of varying: (1) the viscosity contrast between the fluid layers: (2) the Rayleigh number based on the viscosity of the bottom layer; and (3) the thickness of the low-viscosity channel. Good agreement is obtained with the results of geoid anomalies over the Udintsev fracture zone when the viscosity of the top layer is greater than one order of magnitude less than post-glacial rebound values.

Robinson, Elizabeth M.↗

NASA NTRS1990

Effect of artificial viscosity on three-dimensional flow solutions

Artificial viscosity is added either implicitly or explicitly in practically every numerical scheme for suppressing spurious oscillations in the solution of fluid dynamics equations. In the present central-difference scheme, artificial viscosity is added explicitly for suppressing high frequency oscillations and achieving good convergence properties. The amount of artificial viscosity added is controlled through the use of pre-selected coefficients. In the standard scheme, scalar coefficients based on the spectral radii of the Jacobian of convective fluxes are used. However, this can add too much viscosity to the slower waves. Hence, use the matrix-valued coefficients, which give appropriate viscosity for each wave component is suggested. With the matrix-valued coefficients, the central-difference scheme produces more accurate solutions on a given grid, particularly in the vicinity of shocks, while still maintaining good convergence properties.

Turkel, Eli↗

DOE OSTI2026

Lattice-scale variations in viscosity are correlated with solution structure at mineral-water interfaces

At solid-liquid interfaces, the viscosity increases markedly from the bulk due to the collective interactions of ions and water molecules, influencing phenomena relevant to nanofluidics, colloidal dynamics, and electrochemistry. Here, in this study, we investigated dissipative forces at the boehmite-water interface using 3D atomic force microscopy. We observed an increase in interfacial solution viscosity, η, by 10-100-fold as the nanoprobe approached the surface in normal direction, with up to four oscillatory features showing average peaks of η/η bulk = 44-71. Moreover, the viscosity showed sub-nanometer variations within 0.5 nm from the interface, templated by the underlying crystal lattice and correlated with the interfacial solution structure. Beyond a near-wall region of approximately 1.2 nm, the dissipative response was comparable to that in bulk solution. Molecular dynamics simulations, along with statistical mechanical analyses, provided details on hydrodynamic structures near the interface. Specifically, the lattice-dependent dissipative responses are correlated with extensive hydrogen bonding by interfacial water molecules, which increased friction, particularly along the [001] direction. These results demonstrate how solution viscosity at mineral-water interfaces is anisotropic and correlated with the local solution structure, providing insights into the dynamics of nanocrystal attachment.

Viscosity↗

DOE OSTI2025

Stockmayer fluid simulations for viscosity and glass transition temperature of ionic liquids

We develop a Stockmayer fluid model for molecular dynamics simulations of ionic liquids that captures molecular polarization, ionic conductivity, viscosity, and glass transition temperature, using ethylammonium nitrate (EAN) as an example. The ions in EAN are treated as spheres interacting via the Lennard-Jones potential with an embedded point charge and a permanent dipole moment. We show that our simulation results for EAN are consistent with experimental data and then explore the effects of the molecular parameters on the viscosity of ionic liquids. Our results indicate that viscosity monotonically increases with ionic charge and dipole moment but non-monotonically changes with ionic diameter (or molar volume). This non-monotonic trend arises from the competition among the electrostatic interactions, molecular packing, and size asymmetry between the cation and anion. In conclusion, our model also shows that long-lived ion pairs result in higher viscosities.

Coarse-grained simulations↗

DOE OSTI2026

Effect of Oil Viscosity and Impact of Ionic Liquid Additive on Electrically Induced Pitting in Rolling Contact

Electrically induced bearing damage (EIBD) is a growing concern in electric drivetrains, where electrical discharge currents generate localized pitting that accelerates wear and premature failure. While ionic liquids (ILs) have shown promise as lubricant additives due to their natural physical adsorption, strong capabilities of tribofilm formation, and high molecular tunability, their role in mitigating EIBD is little known. This gap is especially evident because lubricant viscosity and film thickness affect discharge behavior, and additive performance in these regimes has not been well explored. In this study, tribological tests were performed using a ball-on-disk pure rolling-contact system under an applied voltage on polyalphaolefin oils of three viscosities (4, 10, and 150 cSt measured at 100 °C), with and without the addition of a phosphonium-phosphate IL. Surface damage was analyzed using scanning electron microscopy (SEM) and stylus profilometry. Damage quantification was based on pit morphology analysis of SEM images. The results provide new insights into how oil viscosity governs the discharge behavior and how an IL additive could influence the pit formation. While viscosity seems to play a significant role, an IL additive shows potential to reduce EIBD and deserves further study.

electrically induced bearing damage (EIBD)↗

NASA NTRS1962

Estimated Viscosities and Thermal Conductivities of Gases at High Temperatures

Viscosities and thermal conductivities, suitable for heat-transfer calculations, were estimated for about 200 gases in the ground state from 100 to 5000 K and 1-atmosphere pressure. Free radicals were included, but excited states and ions were not. Calculations for the transport coefficients were based upon the Lennard-Jones (12-6) potential for all gases. This potential was selected because: (1) It is one of the most realistic models available and (2) intermolecular force constants can be estimated from physical properties or by other techniques when experimental data are not available; such methods for estimating force constants are not as readily available for other potentials. When experimental viscosity data were available, they were used to obtain the force constants; otherwise the constants were estimated. These constants were then used to calculate both the viscosities and thermal conductivities tabulated in this report. For thermal conductivities of polyatomic gases an Eucken-type correction was made to correct for exchange between internal and translational energies. Though this correction may be rather poor at low temperatures, it becomes more satisfactory with increasing temperature. It was not possible to obtain force constants from experimental thermal conductivity data except for the inert atoms, because most conductivity data are available at low temperatures only (200 to 400 K), the temperature range where the Eucken correction is probably most in error. However, if the same set of force constants is used for both viscosity and thermal conductivity, there is a large degree of cancellation of error when these properties are used in heat-transfer equations such as the Dittus-Boelter equation. It is therefore concluded that the properties tabulated in this report are suitable for heat-transfer calculations of gaseous systems.

HEAT TRANSFER↗

DOE OSTI2025

Reference Correlations for the Density and Viscosity of Molten Alkali and Alkaline Earth Fluoride Salts

While there is a significant body of literature pertaining to thermophysical property measurements of molten salts, there is often a wide degree of variability among independent measurements of the same compounds. As such, the scientific community benefits greatly from an unbiased, independent assessment of duplicate datasets, so that reference correlations which describe these thermophysical properties as functions of temperature can be determined and then commonly used by researchers, scientists, and engineers. With regard to molten fluoride compounds, a significant time has elapsed since density and viscosity reference correlations have been determined; Janz conducted the most recent effort, in 1988, to provide reference correlations for the densities and viscosities of molten fluoride compounds via the National Standard Reference Data System coordinated by the National Bureau of Standards. Since then, new data have been published for molten fluoride compounds, and a new precedent has surfaced for putting forth reference correlations that involve fitting to multiple primary datasets. In this work, reference correlations are put forth for molten alkali and alkaline earth fluoride compounds in an effort to provide updated, improved correlations for general use. For molten alkali fluoride densities, estimated uncertainties with a 95% confidence interval are summarized as follows: LiF (0.63%), NaF (0.48%), KF (0.76%), RbF (0.93%), and CsF (0.75%). For molten alkaline earth fluoride densities, an estimated uncertainty was not able to be quantified for BeF 2 because of limited data; however, estimated uncertainties with a 95% confidence interval are summarized as follows for the remaining alkaline earth fluorides: MgF 2 (1.5%), CaF 2 (0.92%), SrF 2 (1.6%), and BaF 2 (0.23%). For molten alkali fluoride viscosities, uncertainty was not able to be quantified for RbF and CsF because of limited data; however, estimated uncertainties with a 95% confidence interval are summarized as follows for the remaining alkali fluorides: LiF (4.4%), NaF (3.0%), and KF (4.0%). For molten alkaline earth fluoride viscosities, limited consistent data resulted in the recommendation of single datasets (from literature) that are deemed to be the most trustworthy based on the quality of the underlying experimental studies.

Birri, A. [Oak Ridge National Laboratory (ORNL), O↗

NASA NTRS1974

Effects of iron oxidation state on viscosity, lunar composition 15555

The viscous flow behavior of a 9.6-kg lunar rock containing 22.5 wt.% FeO was studied in the temperature ranges from 620 to 700 C and from 1215 to 1400 C. The material was synthesized under mildy reducing conditions to simulate the Fe(2+)/total Fe ratio of the lunar environment. The effect of iron oxidation state on flow behavior in the high viscosity region is studied for specimens of the 15555 composition with Fe(2+) concentration ratios of 0.94, 0.76, and 0.20. A change in ratio from 0.94 to 0.76 had no observable effect on viscosity, whereas a change from 0.76 to 0.20 was accompanied by a drastic increase in viscosity (some three orders of magnitude) at a given temperature, but without changing the form of the variation of viscosity with temperature. The flow behavior is analyzed as a function of the structural features of the glasses.

Cukierman, M.↗

NASA NTRS1979

Release adiabat measurements on minerals - The effect of viscosity

The paper examines the effect of viscosity in the release adiabat measurements on minerals. The current inversion of pressure-particle velocity data for release from a high-pressure shock state to a pressure-density path usually depends critically upon the assumption that the release process is isentropic. It has been shown that the effective viscosity for geological materials below stresses of 150 GPa must be at least 1000 kg/m/s so that viscous work in the shock state remains small compared to mechanical work recovered upon adiabatic rarefaction. The magnitude of the shear stress in the shock state in minerals and viscosities of engineering materials shocked to pressures below 150 GPa show effective viscosities of about 1000 kg/m/s or less indicating that the conditions for isentropic release of materials from shock states are achieved and that the Riemann integral can be applied to obtain pressure-density states along the release adiabats of minerals.

Jeanloz, R.↗

NASA NTRS1983

Postglacial rebound observed by Lageos and the effective viscosity of the lower mantle

Sixty-four observations of the orbital node made by the Lageos satellite over a five year time interval reveal an acceleration of (-8.1 + or 1.8) x 10 to the -8 power arcseconds day/2 due to a source which is not presently modeled in the GEODYN orbit determination computer program. This acceleration cannot be explained by the ocean tide with 18.6 year period, assuming it to be an equilibrium tide. Instead it seems to be due to postglacial rebound, which changes the J(2) coefficient in the spherical harmonic expansion of the earth's gravitational field at the rate of (-8.2 + or - 18) x 10 to the -19th power/s; this in turn accelerates the node. This rate does not agree with the -32 x 10 to the -19th power/s predicted by Wu and Peltier's (1982) L2 model, which has upper and lower mantle effective viscosities of 10 to the 21st and 22nd powers Pa's, respectively. it does agree well with their L1 model, which gives about 10 x 10 to the 19th power/s. Since the effective viscosity is 10 to the 21st power Pa s throughout the entire mantle in the L1 model, the results support the contentions that the effective viscosity is near 10 to the 21st power Pa s everywhere in the mantle, and this relatively low value for the effective viscosity may have permitted several degrees of polar wander due to glaciation during the Quaternary Ice Age.

Rubincam, D. P.↗

NASA NTRS1983

Particle size effects on viscosity of silver pastes: A manufacturer's view

Particles from a variety of silver powders were investigated by scanning electron microscopy and particle size analyses. Particle size distribution curves and volume population graphs were prepared for these silver powders and for glass powders with optimum, extra fine and coarse particle sizes. The viscosity at a given shear rate and slope of viscosity over a range of shear rates were determined for thick film pastes made with these powders. Because of particle anomalies and variations, the need for flexibility to achieve the best printing qualities for silver pastes was evident. It was established that print quality, dried and fired film density and optimum contact of silver particles with silicon, important for cell electrical output, could be achieved by adjusting the slope of viscosity that fell outside of the range, -0.550 to -0.650. This was accomplished through organic vehicle technology that permitted a change in the slope of viscosity, up or down, while maintaining a constant silver and total solids content.

Provance, J.↗

NASA NTRS1984

Postglacial rebound observed by Lageos and the effective viscosity of the lower mantle

Sixty-four observations of the orbital node made by the Lageos satellite over a five year time interval reveal an acceleration of (-8.1 + or - 1.8) x 10 to the -8 power arcseconds day/2 due to a source which is not presently modeled in the GEODYN orbit determination computer program. This acceleration cannot be explained by the ocean tide with 18.6 year period, assuming it to be an equilibrium tide. Instead it seems to be due to postglacial rebound, which changes the J(2) coefficient in the spherical harmonic expansion of the earth's gravitational field at the rate of (-8.2 + or - 18) x 10 to the -19th power/s; this in turn accelerates the node. This rate does not agree with the -32 x 10 to the -19th power/s predicted by Wu and Peltier's (1982) L2 model, which has upper and lower mantle effective viscosities of 10 to the 21st and 22nd powers Pa's, respectively. It does agree well with their L1 model, which gives about 10 x 10 to the 19th power/s. Since the effective viscosity is 10 to the 21st power Pa s throughout the entire mantle in the L1 model, the results support the contentions that the efective viscosity is near 10 to the 21st power Pa s everyhere in the mantle, and this relatively low value for the effective viscosity may have permitted several degrees of polar wander due to glaciation during the Quaternary Ice Age. Previously announced in STAR as N84-13705

Rubincam, D. P.↗